Installation andAssembly - All-in-one Projector Adapter Plate for
InFocus® Projectors
Model: SP-CEIL-UNIV
This product is intended for use with UL
Listed products and must be installed
by a qualified professional installer.
Maximum Load Capacity: 25 lb (11 kg)
R
Read instruction sheet before you start installation and assembly.
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
IMPORTANT! Turn to the appropriate page for your ceiling installation.
Applications:
FlushMount ................................................................................................................................................. page 5
ExtensionColumn........................................................................................................................................ page 6
Lightweight Suspended Ceiling Plate ....................................................................................................... page 7
Installations:
To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings........................................................................................ page 3
To Concrete Ceilings.................................................................................................................................... page 4
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
1 of 11
Disengage connection block from projector mount assembly (A) by unscrewing captive screw and sliding out
connection block as shown.
A
CONNECTIONBLOCK
CAPTIVESCREW
Installation To Wood Joist Finished Ceilings, Exposed
Wood Joists, or Wood Beam Ceilings
Drill two 5/32" (4 mm) dia. holes to a minimum depth
of 2.5" (64 mm). Attach ceiling plate (Q) with two
#14 x 2.5" (6 mm x 65 mm) wood screws (F) as
shown using 3/8" (10 mm) socket wrench. Tighten
wood screws (F) so ceiling plate (Q) is firmly
attached.
WOOD
JOIST
CEILING
WARNING
• Tighten wood screws so that ceiling plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
Q
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joist. The use of an "edge to edge" stud
finder is highly recommended.
F
F
Skip to step 7.
WOOD
JOIST
For optional Cord Management,
install two spacers (L) between ceiling
plate (Q) and ceiling.
CEILING
L
L
Q
F
F
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
3 of 11
Installation to Concrete Ceilings
Alligator® concrete anchors are recommended.
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (Q) using two
concrete anchors (G) and #14 x 2.5" wood screws (F)
as shown in Illustration A and 1, 2, and 3. Tighten all
fasteners.
G
Skip to step 7.
CONCRETECEILING
Q
WARNING
F
• Make sure that the supporting surface will safely
support the combined load of the equipment and all
attached hardware and components.
• Tighten concrete anchor bolt firmly, but do not over-
tighten. Overtightening can damage the bolt, greatly
reducing its holding power.
Illustration A
• Never tighten in excess of 80 in • lb (9 N.M.).
concrete
ceiling
1
WARNING
• Concrete anchors are not intended for attachment to
G
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete wall
covered with plaster/drywall is unavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
Drill hole and insert anchor.
2
Q
F
G
INCORRECT
Place ceiling plate over anchor and secure with screw.
metal
concrete
bracket
3
plaster/
dry wall
G
F
After repeating step one tighten all fasteners.
CORRECT
metal
bracket
concrete
plaster/
dry wall
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
4 of 11
Flush Mount Installation
Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) with two
#14 x 2.5" (6 mm x 65 mm) wood screws (F) and two flat washers (E) as shown in figure 1 or figure 2 depending
on joist orientation. Tighten wood screws (F) using 3/8" (10 mm) socket wrench until projector mount assembly (A)
is firmly attached.
WARNING
• Tighten wood screws so that projector mount assem-
bly is firmly attached, but do not overtighten. Overtight-
ening can damage the screws, greatly reducing their
holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the joist. The use of an "edge to edge" stud
finder is highly recommended.
Skip to step 7.
WOOD JOIST
WOOD JOIST
A
FRONT OF
MOUNT
FRONT OF
MOUNT
A
E
F
E
F
figure 1
figure 2
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
5 of 11
Installation to Extension Column (SP-EXTARM-01, SP-
EXTARM-02, SP-EXTARM-03, SP-EXTARM-04)
Q
Screw extension column (sold separately) to
ceiling plate (Q). Align the notch with one of the
four holes in the ceiling plate (Q) and secure
extension column with a M5 x 10 mm socket pin
screw (M) using security allen wrench (B). See
detail 3.
Screw projector mount assembly (A) onto the
extension column as shown in detail 4.
EXTENSIONCOLUMN
(SOLD SEPARATELY)
(UL LISTED)
N
Q
M
Note: For 3/4" extension columns, reducer
ACC 913 will be required as shown in detail 5.
Tighten swivel stop screw against extension
column or reducer using security allen wrench (B).
EXTENSION
COLUMN
Note: Swivel stop screw is used to jam against
threads of extension column or reducer to prevent
any excess movement of projector mount
assembly (A). Do not overtighten screw;
overtighteningscrewwilldamagethreadsmaking
it difficult to separate products.
DETAIL 3
Note: Slotted set screws (N) are used to jam
against the threads of each connecting joint to
preventanyexcessmovement.Donotovertighten
screws;overtighteningscrewswilldamage
threads making it difficult to separate the
products.
A
BACK OF
MOUNT
SWIVELSTOPSCREW
Skip to step 7.
DETAIL 4
3/4" EXTENSION COLUMN
ACC 913
(NOT UL LISTED)
BACK OF
MOUNT
A
SWIVELSTOPSCREW
DETAIL 5
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
6 of 11
Installation to
LIGHTWEIGHT
SUSPENDEDCEILING
PLATE (SOLD
Lightweight Suspended
Ceiling Plate
SEPARATELY)
(EXT-LTMT-PLTB)
Refer to instruction sheet for lightweight
suspended ceiling plate (sold
separately) for attachment of ceiling
plate to ceiling.
RETAINING COLLAR
M
Screw extension column (sold
separately) to retaining collar in ceiling
tray. Align the notch with one of the
four holes in retaining collar and secure
extension column with a M5 x 10 mm
socket pin screw (M) using security
allen wrench (B). See detail 6.
N
DETAIL 6
EXTENSION
COLUMN
(UL LISTED)
Screw projector mount assembly (A)
onto the extension column as shown in
detail 7.
Note: For 3/4" extension columns,
reducer ACC 913 will be required as
shown in detail 8.
Tighten swivel stop screw against
extension column or reducer using
security allen wrench (B).
A
Note: Swivel stop screw is used to jam
against threads of extension column or
reducer to prevent any excess
movementofprojectormountassembly
(A). Donotovertightenscrew;
overtighteningscrewwilldamage
threads making it difficult to separate
products.
SWIVEL STOP SCREW
DETAIL 7
Note: Slotted set screws (N) are used
to jam against the threads of each
connecting joint to prevent any excess
movement.Donotovertightenscrews;
overtighteningscrewswilldamage
threads making it difficult to separate
the products.
DETAIL 8
3/4" EXTENSION
COLUMN
Skip to step 7.
P
L
T
B
ACC 913
(NOT UL
LISTED)
BACK OF
MOUNT
A
SWIVELSTOPSCREW
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
7 of 11
Note: The projector adapter plate and projector you are installing may differ in appearance from the sample illustrated
below.
Align shoulder on connection block opposite of front of projector. Attach adapter plate (R) to connection block from
projector mount assembly (A) using two #10-32 x 3/8" serrated socket pin screws (C) as shown.
CONNECTION BLOCK
SHOULDER
ADAPTER PLATE
R
FRONTOF
PROJECTOR
C
P
R
Attach extension brackets (S) to adapter plate (R)
using two M4 x 6 mm serrated socket pin screws (P).
For specific models, see step 8H.
S
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
8 of 11
Flip projector upside down. Find your projector from the models listed below. Using the holes indicated on the corre-
sponding hole pattern diagram, attach adapter plate (R) to projector using three M4 x 16 mm serrated socket pin
screws (H) and three .198 x .313 x .375 retaining spacers (J).
Notes:
Retaining spacers go between adapter plate and projector.
* Front of projector.
** Projectors using hole pattern G use one M4 x 12 mm screw (I) and one .198 x .313 x .187 retaining spacer (K)
where indicated.
*** Using holes indicated in hole pattern H, attach adapter plate (R) to projector using four M6 x 12 mm serrated
socket pin screws (O) and four spacers (L)
A. C200, DP6500X, LP650, SP5700,
B. C40, C50, DP2000S, DP2000X,
C. LP340, LP350, LP500, LP530,
SP7200, SP7205, SP7210
LP240, LP250
SP110
*
*
*
R
R
R
D. C100, C105, DP6150, DP6155,
E. C109, C110, DP8000, LP790,
F. C170, LP600
LP690
SP4800, SP4805, X1, X1a, X2, X3
*
*
*
R
R
R
I. C410, C420, LP815, LP820,
H. C440, C450, C460, DP8400X,
G. C160, C180, LP540, LP640,
DP8500X, LP840, LP850, LP860
SP5000
DP8200X
S
***
*
***
*
*
S
**
R
R
***
R
***
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
9 of 11
K. IN24, IN26
J. IN72, IN74, IN76
*
*
R
R
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the projector.
Slide connection block with projector into projector mount
assembly (A) as shown. Tighten captive screw to secure
projector to projector mount assembly (A).
IMPORTANT: For security installations, insert
one #10-32 x 1/4" socket pin screw (D) through
projector mount assembly (A) and into connection
block as shown.
CONNECTIONBLOCK
A
CONNECTIONBLOCK
A
FRONTOFMOUNT
D
CAPTIVESCREW
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
10 of 11
Projector Alignment
To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen
wood screws (F), or locknuts for threaded rods, until projector mount can be rotated. Rotate mount to desired
position and retighten screws or locknuts.
To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Loosen two screws on projector mount assembly (A) indicated
below. Tilt mount to desired position and retighten screws.
To adjust roll (side to side tilt): Loosen two screws on projector mount assembly (A) indicated below. Tilt mount
to desired position and retighten screws.
SCREW FOR SWIVEL STOP
A
SCREWS FOR ROLL
SCREWS FOR PITCH
ADJUSTMENT
ADJUSTMENT
BACKOFMOUNT
ISSUED: 10-22-04 SHEET #: 055-9236-5 01-10-06
11 of 11
|