FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference
at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Can-
ada.
Safety Certifications
UL, CUL, TÜV, NOM, IRAM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interfer-
ence, in which case the user may be required to take adequate measures. The typ-
ical use is in a conference room, meeting room or auditorium.
Remote Control Warning
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and
1040.11. Remote control complies with applicable requirements of EN 60 825-1:
1994 +A11.
Safety Instructions
Introduction
Image Resolution
Compatibility
Unpacking the Projector
Usage Guidelines
If You Need Assistance
Warranty
1
4
Setting up the Projector
Connecting a Computer Using a VESA Cable
Connecting a USB type B mouse
Connecting a Computer using BNC Cables
Connecting a Computer with an M1-DA Cable
Connecting a Computer with an RS-232 Cable
Connecting a Video Player
Connecting a Video Player using BNC Cables
Connecting External Speakers
13
17
Connecting the Remote Control Cable
Turning Off the Projector
Using the Projector
Basic Image Adjustment
Adjusting the Projector
Using the Remote Control
Using the On-Screen Menus
Display Menu
Audio Menu
Image Menu
Controls Menu
Language Menu
24
28
30
32
35
38
38
Status Menu
i
T
a
b
l
e
o
f
C
o
n
t
e
Maintenance & Troubleshooting
Cleaning the Lens
Replacing the Projection Lamp
Using the Security Lock
41
Troubleshooting
Appendix
Specifications
Accessories
Portable and Laptop Activation Chart
Using Video Mirroring with a PowerBook Computer
Projected Image Sizes
49
49
52
57
58
59
RS232 Terminal Specifications
Index
63
ii
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instruc-
tions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
• Warning: Statements identify conditions or practices that
could result in personal injury.
• Caution:Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention: For information about usage of a feature, please
refer to the User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
Warning: Laser radiation. Do not stare into laser beam.
Safety Terms:
• Warning: Don’t look directly into the lens when the lamp is
turned on.
•Warning: To replace the lamp, turn the projector off by
unplugging the power cord. To avoid burns, wait 30
minutes before opening the lamp door. Follow all instructions
provided in this User’s Guide.
iii
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
•Warning: Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
•Warning: Visible laser radiation. Do not stare into
beam.
• Warning: Refer all service to qualified service personnel. Ser-
vicing your own projector will void the warranty. See the fol-
lowing page for the customer service contact information.
• Caution: Don’t block ventilation openings.
damage your projector.
sunlight.
• Caution: Do not drop the projector. Transport the projector in
an InFocus-approved case; see page 50 for a list of cases.
• Caution: For ceiling mount installations, please use the ceiling
mount recommended in this User’s Guide on page 51 and fol-
low all instructions provided with it.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb ruptur-
ing, thoroughly clean the area behind the projector and discard
any edible items placed in that area.
Do not place objects in
this area behind the projector
iv
Customer Service
If you need assistance, call InFocus Customer Service directly at
1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST,
Monday through Friday. Support is available in North America
after hours and weekends for a fee at 1-888-592-6800.
In Europe, call InFocus in The Netherlands at (31) 35-6474010.
In Asia, call InFocus in Singapore at (65) 332-0659.
v
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
vi
INTRODUCTION
The InFocus® LP930™ XGA multimedia projector is specifically
designed for fixed installations. The projector features an M1-DA
connector for easy, built-in digital/analog and USB connectivity.
It allows four computer, three video, and three audio inputs, one
audio output, and RS-232 control.
Image Resolution
NOTE: The LP930 automatically
expands 640x480 and 800x600
images to 1024x768. You can dis-
play these images at their native
resolutions by turning off the Auto
Resize feature. See “Resize” on
page 32 for more information.
The native resolution of the 930’s projected image is XGA
1024x768. Screen resolutions between 1024x768 and 1280x1024
are compressed to 1024x768. The projector cannot compress
screen resolutions above 1280x1024. If your computer’s screen
resolution is higher than 1280x1024, reset it to a lower resolution
before you connect the projector.
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including laptops, up to 1280x1024
resolution.
• Apple® Macintosh® and PowerBook® computers up to
1280x1024 resolution.
NOTE: The projector is compati-
ers and laser disc players.
ble with 1080i HDTV format.
• Selected workstations (contact your dealer for details).
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included. Contact your InFocus dealer imme-
diately if anything is missing. User’s Guides are also available
for download from our website at www.infocus.com.
NOTE: The projector is compati-
ble with many third-party control-
lers and amplifiers, including
AMX, Crestron, and Extron. Call
your dealer for details.
A registration card is included in the box. Register to receive
product updates, announcements, and special offers from
InFocus. Or, register online at www.infocus.com/service/register
and you will be automatically entered to win free merchandise.
1
I
n
t
r
o
d
u
c
t
i
o
n
NOTE: The contents of your
1
shipping box may vary depending
on the projector configuration
you’ve ordered.
2
p
o
w
e
r
st
a
n
c
o
d
m
p
b
y
fre
e
ze
vi
d
eo
b
ri
g
h
tn
e
ss
v
o
lu
m
e
3
la
se
r
6
5
4
FIGURE 1
Shipping box contents
1. LP930 projector + lens cap
2. Power cord
4. VESA computer cable
5. Audio/Video cable
6. User’s Guide and CD
3. Remote control
NOTE: Long throw zoom, wide
angle zoom, and ultra wide angle
lenses are also available. See
page 50 for details.
2
keypad
connector panel
zoom ring
speaker
power
cord
connector
focus ring
FIGURE 2
Side view of projector
Usage Guidelines
• Do not look directly into the projection lens when the lamp is
turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
• Transport the projector in a vendor-approved hard or soft case.
Part numbers for these cases are listed on page 50.
3
I
n
t
r
o
d
u
c
t
i
o
n
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 45. Or, check the
Service and Support section of our website at
FAQs, and support contacts including a technical support e-mail
form.
If those sources don’t answer your question, call your InFocus
dealer. You can also call InFocus Customer Service directly at
1-800-799-9911. Call between 6 a.m. and 6 p.m. PST, Monday
through Friday. Service is available in North America after hours
and on weekends for a fee at 1-888-592-6800.
In Europe, call InFocus in The Netherlands at (31) 35-6474010.
In Asia, call InFocus in Singapore at (65) 332-0659.
Or, send us an e-mail at [email protected]
Warranty
This product is backed by a limited two-year warranty. The
details of the warranty are printed at the back of this manual. A
longer term warranty can be purchased from your InFocus
dealer. Refer to page 50 for the part number.
4
SETTING UP THE PROJECTOR
• The projector must be within 10 feet (3 m) of your power
source and within 6 feet (1.8 m) of your computer.
• If you want to project from behind a translucent screen, set
on page 36 to reverse the image.
• If you are installing the projector on the ceiling, refer to the
installation guide that comes with the Ceiling Mount Kit for
more information. To turn the image upside down, see
“Ceiling Projection” on page 36. The Ceiling Mount Kit is
sold separately; see “Optional Accessories” on page 50.
2 Position the projector the desired distance from the screen.
• The distance from the lens of the projector to the screen and
the zoom lens setting determine the size of the projected
image. Table 1 shows example projected image sizes and
minimum and maximum distances to the screen.
The formulas for distance to the screen are:
Max distance (ft) = diagonal image size (ft) ÷.49
Min distance (ft) = diagonal image size (ft) ÷.69
Table 1:
NOTE: For a similar table for the
optional short throw and long
throw lenses, see page 58 of the
Appendix.
Diagonal Image Size and Width at Maximum and Minimum Distance
to Screen-Standard Lens
Distance to screen
Diagonal
Image Size
(inches)
Maximum
distance
(feet)
Minimum
Distance
(feet)
Image Width
(inches)
300
240
180
144
120
96
240
192
144
115
96
51
41
31
24
20
16
12
10
8
36
29
22
17
14
12
9
77
72
58
60
48
7
5
48
38
6
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
zoom adjustment range:
20-14’
90º
A
0
s
R
G
B
90º
BNC
BNC
L
R
L
R
L
R
G
B
R
out
In
In
In
minimum L: 14’
maximum L: 20’
distance between lens and screen: L
FIGURE 3
Projected image size for 10’ diagonal image size
The projector is equipped with a lens shift feature that allows you
to adjust the projection height (move the image along the wall)
without moving the projector, while still maintaining a perfectly
square image. Turn the lens shift knob on the side of the projector
to make this adjustment (Figure 4).
FIGURE 4
Adjusting the lens shift
6
The bottom of the image can move from half way below the pro-
jector’s lens (Figure 5) to parallel with the lens (Figure 6).
Example: With a 10’ image, at the lowest projection angle, the bot-
tom of the image is 5’ below the projector’s lens; at the highest
projection angle, the bottom of the image is parallel with the lens.
10’ high
image
A
0
s
R
G
B
lens center
BNC
BNC
L
R
L
R
L
R
G
B
R
out
In
In
In
H
bottom of image
5’ below lens
FIGURE 5
Lowest image projection angle
10’ high
image
bottom of image
parallel with lens
A
0
s
R
G
B
BNC
BNC
L
R
L
R
L
R
G
B
R
out
In
In
In
lens center
FIGURE 6
Highest image projection angle
Once you know the diagonal image size, you can figure out the
width and height using these formulas:
width (inches) = diagonal (inches) x 0.8
height (inches) = width (inches) x 0.75
7
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
The following tables give the lens shift values for desktop and
ceiling-mounted setups for various image sizes. The lower lens
shift position represents the highest the projector can be above
the bottom of the screen; the upper lens shift position represents
the lowest the projector can be below the bottom of the screen.
Table 2:
Lens Shift Positions for Desktop Setup
Distance from lens center to
lower edge of screen (H)
Diagonal
Image Size
(inches)
Lower lens
shift position
(inches)
Upper lens
shift position
(inches)
300
240
180
144
120
96
90
72
54
43
36
29
22
18
14
0
0
0
0
0
0
0
0
0
72
60
48
When the projector is ceiling mounted, use the upper edge of the
screen as the base line.
Table 3:
Lens Shift Positions for Ceiling-Mounted Setup
Distance from lens center to
upper edge of screen (H)
Diagonal
Image Size
(inches)
Lower lens
shift position
(inches)
Upper lens
shift position
(inches)
300
240
180
144
120
96
90
72
54
43
36
29
22
18
14
0
0
0
0
0
0
0
0
0
72
60
48
8
high edge of screen
lens center
H
lens center
FIGURE 7
Lens shift with ceiling-mounted projector
3 Make sure the projector is unplugged and your computer is
turned off.
Now you’re ready to connect your equipment.
Steps for connecting the different types of equipment are given
on the pages listed below.
NOTE: The CableWizard connec-
tor is used with the optional
CableWizard2 or 3, a connection
hub containing mouse, audio,
monitor and computer connectors.
It is optimized for ceiling-mounted
installations, and can be used with
a 60’ extension cable. See
Equipment you want to connect Page
Computer with VESA cable
USB type B mouse
Computer with BNC cables
Computer with M1-DA cable
RS-232 cable
page 11
page 11
page 11
page 12
page 12
page 13
page 15
page 15
“Optional Accessories” on
Video player
page 50. This input is designated
Computer CableWizard.
External speaker
Remote cable
9
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Composite
Video
wired
remote
Computer M1
Analog/Digital
Computer RGBHV
USB
Computer
Computer
VESA
5 BNCs
CableWizard
S-video
USB
Video
S-Video
M1-DA
CableWizard
VESA
R
G
V
B
Wired
Remote
Y
Cr
Cb
RS232 Serial
In
R
R
R
L
L
L
out
In
In
H
Audio 1
Audio 2
Audio 3
external
speakers
RS-232
Component Video
3 BNCs
audio
inputs
FIGURE 8
Connector panel
The projector has the following audio/video inputs:
NOTE: Make sure all equipment
is turned off before connecting
equipment.
Source
Video
Audio
Computer
RGBHV
3 Single-ended analog RGB
+ 2 H&V sync (5 BNCs)
Left and right line-level
(2 RCAs)
Computer
VESA
VESA Single-ended analog
RGB (HD-15)
Left and right line-level
(2 RCAs)
Computer
M1
M1-DA Single-ended ana-
log or digital
Left and right line-level
(2 RCAs)
Computer
CableWiz-
ard
CableWizard Analog RGB
Combined with CableWizard
Compo-
nent Video
Base-band component video
(BNC)
Left and right line-level
(2 RCAs)
Composite
Video
Base-band composite video
(RCA)
Left and right line-level
(2 RCAs)
S-Video
S-video Y/C (4-pin circular)
Left and right line-level
(2 RCAs)
10
Connecting a Computer Using a VESA Cable
This input is designated Computer VESA.
1 Plug one end of the supplied VESA cable into the video con-
nector on your computer. Plug the other end into the VESA
connector on the projector.
NOTE: If you are connecting an
older Macintosh computer that
has a 2-row 15-pin connector, you
must use a Mac adaptor between
the computer and the projector.
See “Optional Accessories” on
page 50.
2 If you want audio with your presentation, plug an audio cable
(not supplied) into the audio connector on your computer.
Plug the other end into a
In connector on the projector.
A
s
R
G
B
0
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
In
VESA cable
FIGURE 9
Connecting the projector to a computer using a VESA cable
Connecting a USB type B mouse
NOTE: When all 5 BNCs are con-
nected, the projector handles sepa-
rate synch on H and V. When 4
BNCs are connected, the projector
handles a composite sync on H.
When 3 BNCs are connected, the
projector handles a composite sync
on G.
You can control the computer’s mouse with the projector’s key-
pad or remote by connecting a USB mouse cable to the USB con-
nector on the projector (Figure 8 on page 10) and on your
computer. This feature is available for PC Computer RGBHV and
VESA sources only. It is not supported on the Macintosh plat-
mouse.
Connecting a Computer using BNC Cables
Connect the BNC cables to the appropriate RGBHV connectors
on the projector (Figure 8 on page 10) and on your computer.
This input is designated Computer RGBHV.
11
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Connecting a Computer with an M1-DA Cable
See “Optional Accessories” on page 50 to order this cable.
This input is designated Computer M1 Analog or Computer M1
Digital.
1 Plug the
end of the M1-DA computer cable into the
M1-DA connector on the projector.
2 Plug the
end of the M1-DA computer cable into the video
connector on your computer.
NOTE: Many laptop computers
do not automatically turn on their
external video port when a
secondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the
external video port. Activation
commands for some laptop
computers are listed in the
Appendix of this
A
0
s
R
G
B
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
USB mouse
M1-DA analog computer cable
FIGURE 10
manual on page 52.
Connecting the projector to a computer using the M1-DA cable
Do you want to control the computer’s mouse from the projector’s
remote or keypad?
1 Plug the
end of the M1-DA computer cable into a
USB mouse connector on your computer.
NOTE: The USB mouse is
supported for use with
Do you want to play your computer’s audio on the projector?
Windows 98, Windows 2000, and
Apple OS 8.5 and higher only.
1 Plug an audio cable (not supplied) into the audio connector
on your computer.
2 Plug the other end of the audio cable into a
In connector
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it (it is hot-
pluggable).
Connecting a Computer with an RS-232 Cable
You can control the projector from an LCD control panel by con-
necting an RS-232 cable to the projector (see Figure 8 on page 10).
See “RS232 Terminal Specifications” on page 59 for details.
12
Connecting a Video Player
There are 3 video inputs: Composite video, S-video, and Compo-
nent video. For Composite and S-video, follow these instructions:
the projector.
nector, you’ll need an S-video cable in addition to the A/V
cable. The S-video cable is sold separately. (See “Optional
Accessories” on page 50.)
2 Plug the A/V cable’s yellow connector into the “video-out”
connector on your video player (Figure 11). This connector
may be labeled “To Monitor.”
NOTE: HDTV sources are con-
nected to the projector using the
computer inputs, not the video
inputs. All analog computer inputs
can display HDTV. See the previ-
ous pages for computer connection
instructions.
• If you’re using an S-video cable, connect it to the “S-video
out” connector on the video player (Figure 12).
3 Plug the other yellow connector into the composite video con-
nector on the projector.
• If you’re using S-video, plug the other end of the cable into
the “S-video” connector on the projector (Figure 12).
A
0
s
R
G
B
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
In
A/V cable
FIGURE 11
Connecting the projector to a video player using the standard A/V cable
13
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
A
0
s
R
G
B
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
In
S-video
cable
A/V cable
FIGURE 12
Connecting the projector to a video player using an S-video cable and the A/V cable
4 Plug the A/V cable’s white connector into the left “audio out”
connector on your video player. Plug the cable’s red connector
into the right “audio out” connector on the video player (Fig-
ure 11 and Figure 12).
5 Plug the A/V cable’s other white and red connectors to the
left and right
In ports on the projector.
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, and
SECAM. It automatically adjusts to optimize its performance for
the incoming video. The input signal for SECAM video is similar
to other video signals and cannot be automatically detected,
dard” on page 35 for details.
CAUTION: Your video player
may also have a “Video Out”
connector for a coaxial cable
connection. DO NOT use this to
connect to the projector.
Connecting a Video Player using BNC Cables
Connect the BNC cables and audio cables to the appropriate con-
nectors on the projector (Figure 8 on page 10) and on your video
player.
This input is designated Component Video.
14
Connecting External Speakers
To connect one or two external speakers, plug the speaker cable
into the
out (audio out) connectors on the projector. The
external speaker’s volume is controlled by the projector; see “Vol-
ume + or -” on page 26.
A
0
s
R
G
B
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
In
FIGURE 13
Connecting external speakers
Connecting the Remote Control Cable
If the projector cannot receive the remote’s signal, as may be the
case if you’re using rear projection, connect the remote directly to
the projector with the optional remote cable. See “Optional
Accessories” on page 50.
1 Plug the remote cable into the wired remote connector on the
projector.
NOTE: For more information on
2 Plug the other end into the connector on the remote.
using the remote, see page 22.
A
0
s
R
G
B
BNC
BNC
G
B
R
L
R
L
R
L
R
out
In
In
In
FIGURE 14
Connecting the remote control cable
15
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Powering up the Projector and Adjusting the Image
NOTE: Always use the power cord
2 Plug the power cord into the side of the projector, then plug it
into your electrical outlet. A surge-protected power strip is
recommended.
that shipped with the projector.
• The Power LED on the top of the projector (Figure 20 on
page 24) lights green.
3 Press the power button.
• The Power LED blinks green until the lamps turns on, then
it lights solid green.
NOTE: The first time you connect
your computer to the projector, the
computer may display a message
stating that new hardware was
found. The Add New Hardware
Wizard may appear. Use the
• The startup screen appears.
4 If you connected a video player, turn it on.
• The video image should display on the projection screen. If
a computer source is active, press the source button on the
keypad (page 26) or the video button on the remote to dis-
play your video image. You can select a default source to
determine which source the projector examines first during
power-up for active video; see “Default Source” on page 36.
Wizard to load the correct driver
(the computer considers the
projector a Plug and Play Monitor).
• Use the volume buttons to adjust the volume.
5 Turn on your computer.
• The computer image should display on the projection
screen. If a video source is active, press the source button on
the keypad or the computer button on the remote to display
your computer’s image. Make sure your laptop’s external
video port is activated; see “Portable and Laptop Activation
Chart” on page 52 for details.
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
• If necessary, make adjustments to the image using the pro-
jector’s on-screen menus. To open the menus, press the
menu button on the keypad or remote, then select the Dis-
play or Image menu. For more information about the
menus, see page 27.
determine the correct order.
16
If you want to blank the screen for a short period of time, press
the standby button on the keypad or remote. This blanks the
screen for fifteen minutes, but keeps the projector running. (You
can change the amount of time the projector stays in standby
mode; see “Standby Time” on page 35 for details.) After the
standby time, the projector shuts off. To exit standby mode, press
the standby button again.
To completely power off the projector, press the Power button.
The lamp turns off and the LED blinks orange while the fans con-
tinue to run to cool the projector. After the projector is cooled, the
projector turns off and the LED lights solid green.
NOTE: Lamp life will be extended
if you turn the projector off, then
wait 1 minute while the lamp cools
before unplugging the projector.
17
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
18
USING THE PROJECTOR
This section describes how to use and make adjustments to the
buttons and the options available from the on-screen menus.
Basic Image Adjustment
order (page 16).
2 If the image doesn’t display completely, zoom the image
(page 20), adjust the height of the projector (page 20) or center
the image by adjusting its horizontal or vertical position
screen.
4 If the image appears to shimmer or if it has blurry vertical
bars after you have adjusted the focus, turn Auto Image
(page 32) off and then back on to reset the automatic sync and
tracking. If that doesn’t clear up the image, turn Auto Image
off and adjust the sync (page 33) and/or the tracking
(page 33) manually.
5 If the colors don’t look right, adjust the brightness (page 28).
19
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 15) until the
image is clear. To zoom the image, rotate the zoom ring. This
adjusts the image size without affecting focus.
zoom ring
focus ring
FIGURE 15
Focus ring and zoom ring
The projector is equipped with a projection angle lens shift knob
that provides adjustment from horizontal. This allows you to
adjust the projection height without moving the projector (see
page 8 for lens shift values). It also has a height-adjustment foot,
an elevator button, and a leveling knob.
FIGURE 16
Adjusting the lens shift
20
To adjust the height of the projector, press and hold the elevator
button, raise the projector to the desired height, then release the
button to lock the foot into position. Rotate the leveling knob, if
necessary, to adjust the angle of the projected image.
elevator button
FIGURE 17
elevator foot
Adjusting the height of the projector
A
s
R
G
B
0
G
B
R
BNC
BNC
L
R
L
R
L
R
out
In
In
In
leveling knob
FIGURE 18
Leveling knob
21
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the Remote Control
To control the computer’s mouse from the projector’s remote or
keypad, you must connect either the USB connector on the M1
computer cable to the computer (see page 12) or a type B USB
mouse cable to your computer and the projector (see page 11).
This feature is not supported on the Macintosh platform.
NOTE: If you can’t aim the
remote control at the projector so
that its signal is received — for
example, when using rear
Point the remote control at the projection screen or at the top of
the projector. The range for optimum operation is about 25 feet. If
you point the remote at the projection screen, the distance to the
screen and back to the projector must be less than or equal to 25
rear of the projector.
projection or in a large
auditorium— connect it directly to
the projector with the optional
remote control cable.
The projector ships with a full-feature remote (see page 24 for a
description of the buttons) which includes a laser pointer. The
remote has a disk mouse and two mouse buttons, one on the top
of the remote and one on the bottom (Figure 19).
laser pointer
disk mouse
right mouse button
left mouse button
(on underside of remote)
FIGURE 19
Remote control
22
Press anywhere on the edge of the disk mouse to move the cursor
on the screen. You can move the cursor at any angle by pressing
the corresponding edge of the disk. The mouse button on the top
of the remote simulates your computer’s right mouse button; the
button on the bottom simulates your computer’s left mouse but-
ton. When you press the disk mouse, the remote lights up. The
light goes off about 10 seconds after you stop pressing buttons.
To use the laser pointer, press and hold the laser button. The laser
goes off when the button is released.
If you are creating presentations in Microsoft® PowerPoint®, you
can use the remote’s mouse buttons to navigate through your
presentation while in Slide Show mode. To configure PowerPoint
for this, choose Options from the Tools menu, click the View Tab,
de-select the “Popup Menu on Right Mouse Click” option in the
Slide Show section, then click OK. Then, when you’re in Power-
Point’s Slide Show mode, a left click advances to the next slide
and a right click returns to the previous slide (other PowerPoint
modes are not affected).
NOTE: In some cases, you can
use the projector’s Controls menu
to configure the mouse for Power-
Point. See page 37 for details.
23
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the Keypad and Remote Buttons
While the menus are displayed, the volume, source, and standby
buttons on the keypad act as menu navigation buttons. See
“Using the On-Screen Menus” on page 27 for details.
power
menu
source
volume -
volume +
standby
right mouse
button
left mouse
button
FIGURE 20
Keypad buttons
FIGURE 21
Remote buttons
24
Brightness + or - (remote only)
Adjusting the brightness lightens or darkens the image.
• To darken the image, press -.
• To lighten the image, press +.
Freeze (remote only)
The freeze button halts, or “freezes” the projected image. Use this
button to freeze a frame of video (the video continues to run but
the projected image is frozen). You can also freeze an image from
a computer source on the screen, allowing you to perform other
operations on the computer without the audience seeing them.
Press freeze again when you want the image to return to normal.
Laser (remote only)
The laser button activates a laser beam that can be used as a
pointing device. To use the laser, press and hold the laser button.
Menu
Press menu to open the on-screen menus. Press menu again to
close the menus. When you close the menus, the projector saves
any changes you made. For more information about the on-
screen menus, see page 27.
Power
The power button turns the projector on and off. When you plug
the projector in, the Power LED lights. When you press the power
button, the LED blinks green, then turns solid green and the lamp
turns on.
When you press the power button while the projector is on, the
lamp turns off and the LED blinks orange while the fans continue
to run to cool the projector. After the projector is cooled, the pro-
jector turns off and the LED lights solid green.
25
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Standby
When you press standby, the display and audio turn off and a
blank screen is displayed for 15 minutes. You can change the
amount of time the projector stays in standby mode; see
“Standby Time” on page 35 for details. While the projector is in
standby, the keypad and remote buttons do not affect the projec-
tor and the LED lights orange.
• If you press standby again within the standby time, the projec-
tor returns to normal operations immediately.
• If you don’t press standby again, the projector turns off after the
standby time.
Source (keypad only)
or
Comp and Video (remote only)
When you have more than one source (computer and video) con-
nected to the projector, select between them by pressing the
source button on the keypad or the comp or video button on the
remote. Press comp to display your computer image. Press comp
again to toggle among the computer sources. The sources switch
in this order:
• Computer RGBHV
• Computer VESA
• Computer M1 Analog/Digital
• Computer CableWizard
Press video again to toggle among the video sources. The video
sources switch in this order:
• Component Video
• Composite Video
• S-Video
Volume + or -
• To increase the volume, press +.
• To decrease the volume, press -.
Volume adjustments are saved for each source you have con-
nected.
26
Using the On-Screen Menus
The projector has six drop-down menus that allow you to make
image adjustments and change a variety of settings. Most of these
adjustments aren’t available directly from the keypad.
To open the on-screen menus, press the menu button on the
keypad or remote. This changes the volume, source, and standby
buttons on the keypad to menu navigation buttons. Press the
corresponding buttons to move the cursor up, down, left, or
right, or use the disk mouse on the remote. To select a menu,
move the cursor left or right to highlight the menu you want. The
drop-down menu appears.
NOTE: Some menu items may be
grayed out at certain times. This
indicates the item is not applicable
to your setup (for example, video
standards do not apply to com-
puter sources) or the item is not
enabled until another selection is
made (for example, Manual Track-
ing is not available until Auto
Image is turned off).
menu
>
>
Display Audio Image Controls Language Status
Brightness
Contrast
Tint
source
Color
Color temperature
Sharpness
Blank screen
Reset all
blue
volume -
volume +
use these buttons to navigate through
the menus
standby
FIGURE 22
Keypad navigation buttons and drop-down menu
To change a menu setting, use the up and down navigation but-
tons on the keypad or the disk mouse on the remote to move the
cursor up and down to the item you want to change (the selected
item is highlighted), then use the left and right mouse buttons to
adjust a setting. Some submenus, such as Brightness, consist of a
slider bar you use to increase or decrease a value; some sub-
menus, such as Standby Time, consist of options you scroll
through to select the desired one. All changes are saved when
you close the menus.
To access another menu, use the left and right navigation buttons
to move to the desired menu.
27
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Display Menu
>
>
Display Audio Image Controls Language Status
Brightness
Contrast
Tint
Color
Color temperature
Sharpness
Blank screen
Reset all
blue
FIGURE 23
Display menu
Brightness
Adjusting the brightness changes the intensity of the image.
• Press the left mouse button to darken the image.
• Press the right mouse button to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
• Press the left mouse button to decrease the contrast.
• Press the right mouse button to increase the contrast, making
the blacks appear blacker and the whites appear whiter.
Tint
The tint adjusts the red-green color balance in the projected
image. Changing the Tint setting has no effect on PAL or SECAM
video sources.
• Press the left mouse button to increase the amount of green in
the image.
• Press the right mouse button to increase the amount of red in
the image.
28
Color
The color setting adjusts a video image from black and white to
fully saturated color.
• Press the left mouse button to decrease the amount of color in
the image.
• Press the right mouse button to increase the amount of color in
the image.
Color Temperature
The Color Temperature setting adjusts the amount of red in the
projected image.
• Press the left mouse button to decrease the amount of red in the
image.
• Press the right mouse button to increase the amount of red in
the image.
Sharpness
This setting adjusts the sharpness of a video image.
• Press the left mouse button to decrease the sharpness.
• Press the right mouse button to increase the sharpness.
Blank Screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby. Click the left
or right mouse button to toggle between blue and black.
Reset All
Click the left or right mouse button to reset all the options (except
Language, Video Standard, Audio Source, Plug and Play, Rear
Projection, Standby Time, and projection modes) in all the menus
to their original settings.
29
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Audio Menu
>
>
Display Audio Image Controls Language Status
Volume
Tr e b l e
Bass
Balance
Fade
Audio source audio source 2
FIGURE 24
Audio menu
Volume
• Press the left mouse button to decrease the volume.
NOTE: Changing the volume
using the menu is the same as
changing it using the remote or
keypad.
• Press the right mouse button to increase the volume.
Volume adjustments you make are saved for each source.
Treble
The treble setting controls the high frequencies of your audio
source.
• Press the left mouse button to decrease the treble.
• Press the right mouse button to increase the treble.
Treble adjustments you make are saved for each source.
Bass
The bass setting controls the low frequencies of your audio
source.
• Press the left mouse button to decrease the bass.
• Press the right mouse button to increase the bass.
Bass adjustments you make are saved for each source.
30
Balance
The Balance setting controls the balance between the left and
right speakers. The Balance setting applies to all sources you have
connected.
• Press the left mouse button to increase the amount of sound
coming from the left speaker; press the right mouse button to
increase the amount of sound coming from the right speaker.
Fade
The Fade setting controls the balance between the internal and
external speakers. The setting appears gray and won’t highlight if
external speakers aren’t connected.
• Press the left mouse button to increase the amount of sound
coming from the internal speaker; press the right mouse button
to increase the amount of sound coming from the external
speakers.
Audio Source Select
This setting allows you to match a computer or video input to an
audio input. The projector has four computer and three video
inputs, but only four audio inputs.
Select among audio sources 1, 2, and 3, and CableWizard. (The
CableWizard computer input does not have a separate audio
input. Audio is transmitted in the CableWizard computer input.)
By default, the RGBHV and M1-DA sources are assigned to audio
input 1, the VESA source to audio 2, the CableWizard source to
CableWizard, and all video sources to audio 3. (Figure 8 on page
10 shows the labeled audio inputs on the connector panel.) To
change these assignments, make the desired source active (for
example, the VESA input), then select an audio source.
NOTE: Audio cables must be con-
nected in order to hear sound from
the projector.
31
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Image Menu
>
>
Display Audio Image Controls Language Status
Overscan
on
top
on
Image position
Auto image
Resize
on
Manual sync
Manual tracking
Horizontal position
Vertical position
Zoom
FIGURE 25
Image menu
Overscan
This option crops all the edges of the image to remove noise gen-
erated on the edges by your source. This option is available for
video sources only.
NOTE: Some screen savers
interfere with the operation of
Auto Image. If you’re experiencing
problems, try turning your screen
saver off, then turning Auto Image
off and back on.
Image Position
This setting allows you to re-position a 16x9 or native mode
video image. Select among top, bottom, and center by highlight-
ing Image Position in the menus and clicking either mouse but-
ton to cycle through the options.
Auto Image
The projector automatically adjusts tracking, signal synchroniza-
tion and vertical and horizontal position for most computers
(Auto Image does not apply to video sources). If you want to
adjust these features manually, you must turn off Auto Image first
by highlighting Auto Image in the Image menu and clicking the
left or right mouse button to select “off”.
Resize
This option works differently for computer and video sources.
For computer sources, Resize automatically resizes the image by
scaling it up or down. It only affects computer images that are not
the projector’s native resolution. When Resize is on, the projector
makes the best fit of the image to the computer screen. If you turn
Resize off (by highlighting it in the Image menu and clicking the
left or right mouse button to select “off”), the image may be either
cropped or too small for the screen.
NOTE: When you connect an
HDTV source, the projector
automatically displays the image in
16x9 format.
32
For video sources, Resize allows you to select from among four
different re-sizing options. The default is Standard, which resizes
the image from its original version to fit a standard 4x3 aspect
ratio screen. Widescreen Letterbox preserves the 16x9 aspect ratio
of the original theater version, but the image is placed in a 4x3
space, so black bars appear at the top and bottom of the image.
Enhanced Widescreen also preserves the aspect ratio of the origi-
nal theater version and is designed to be used with content that is
Enhanced for Widescreen TVs. This option yields more detail
than Widescreen Letterbox. Native reduces the Standard size to
match the height of Enhanced Widescreen.
Manual Sync
The projector adjusts signal synchronization automatically for
most computers. But if the projected computer image looks fuzzy
or streaked, try turning Auto Image off then back on again. If the
image still looks bad, try adjusting the signal synchronization
manually:
1 Turn Auto Image off.
NOTE: The Manual Sync,
Manual Tracking, Horiz. Posi-
tion and Vert. Position options
are available only for computer
sources. The projector sets these
options automatically for video
sources.
2 Highlight Manual sync, then press the left or right mouse but-
ton repeatedly until the image is sharp and free of streaks.
Manual Tracking
The projector adjusts tracking automatically to match the video
signal from your computer. However, if the display shows evenly
spaced, fuzzy, vertical lines or if the projected image is too wide
or too narrow for the screen, try turning Auto Image off then back
on again. If the image is still bad, try adjusting the tracking man-
ually:
1 Turn Auto Image off.
2 Highlight Manual tracking, then press the left or right mouse
button repeatedly until the fuzzy vertical bars are gone.
33
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Horizontal position
Follow these steps to manually adjust the horizontal position:
1 Turn Auto Image off.
2 Highlight Horizontal position, then press the left mouse but-
ton to move the image right or press the right mouse button to
move the image left.
Positioning adjustments are saved when you power off the pro-
jector.
Vertical position
Follow these steps to manually adjust the vertical position.
1 Turn Auto Image off.
2 Highlight Vertical position, then press the left mouse button to
move the image down or press the right mouse button to
move the image up.
Positioning adjustments are saved when you power off the pro-
jector.
Zoom
This option allows you to digitally zoom a computer image.
Highlight Zoom, then press either mouse button. A rectangle
appears on the screen. Use the arrow buttons on the keypad or
the disk mouse on the remote to move the rectangle to the area
you want to zoom, then click the right mouse button (not the left
mouse button). The image is zoomed. To zoom further, press the
right mouse button, move the rectangle to the desired area, then
press the right mouse button again. You can zoom three times. To
return the image to normal view, press the left mouse button. The
zoom rectangle appears. To cancel zoom, press the left mouse
again or activate the menu.
NOTE: The Zoom feature is only
available when a computer source
is active. It is not available for
video sources.
34
Controls Menu
>
>
Display Audio Image Controls Language Status
Video standard
Standby time
1 minute
Ceiling projection
Rear projection
Default source
Auto source select
Plug and Play
off
off
computer VESA
off
off
USB: Mouse Button
left/right
USB: Inhibit Screen Saver off
Display messages
on
on
Display startup screen
FIGURE 26
Controls menu
Video Standard
When Video standard is set to Auto, the projector attempts to
pick the video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-
N,PAL-60, or SECAM) automatically based on the input signal it
receives. (The video standard options may vary depending on
your region of the world.) The input signal for SECAM video is
similar to other video signals and cannot be automatically
detected, therefore SECAM must be chosen manually. If the pro-
jector is unable to detect the correct standard, the colors might
not look right or the image might appear “torn.” If this happens,
manually select a standard by clicking the left or right mouse but-
ton and cycling through the standards.
NOTE: If you already know the
video standard used in your geo-
graphical area, it’s often best to
manually select it.
Standby Time
This option lets you select how long the lamp stays on and the
blank screen is displayed when the projector enters standby
mode before the projector turns off. Select among instant, 1, 5, 10,
15 and 30 minutes and 1 and 2 hours by clicking the left or right
mouse button and cycling through the options.
35
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Ceiling Projection
When you turn Ceiling Projection on, the projector turns the
image upside down for ceiling-mounted projection. Highlight
Ceiling Projection, then click the left or right mouse button to
turn this feature on and off.
Rear Projection
When you turn Rear Projection on, the projector reverses the
image so you can project from behind a translucent screen. High-
light Rear Projection, then click the left or right mouse button to
turn this feature on and off.
Default Source
Default Source toggles among Computer RGBHV, Computer
VESA, Computer M1 Analog, Computer M1 Digital, Computer
CableWizard and Component Video, Composite Video, and
S-video. This determines which source the projector checks first
for active video during power-up. Highlight Default Source and
click the left or right mouse button to toggle among the options.
Auto Source Select
This setting toggles between On and Off. When this feature is Off,
the projector defaults to the source selected in Default Source. To
display another source, you must manually select one by press-
ing the source button on the keypad or the computer or video but-
ton on the remote. When this feature is On, the projector
automatically finds the active source, checking the default source
first. Highlight Auto Source Select and click the left or right
mouse button to turn this feature on and off.
Plug and Play
This setting toggles between On and Off. When it is On, most
new computers will automatically recognize the projector, then
set the monitor resolution and refresh rate accordingly. You need
to set the Plug and Play setting to Off for the projector to display
properly on some older computers. The Plug and Play setting
does not affect video images.
If the projector’s display constantly changes between the com-
puter image and the message, “Perfecting the image”, you may
need to turn Plug and Play Off.
36
USB: Mouse Button
This setting toggles between Left/Right and Page up/Page
down. Use Page up/Page down if you want to use the remote or
keypad mouse buttons to advance slides in PowerPoint. A type B
USB mouse cable must be connected to use this feature. See
page 11 for details. This feature is available for PC Computer
RGBHV and VESA sources only. It is not supported on the Macin-
tosh platform.
USB: Inhibit Screen Saver
This setting toggles between On and Off. When it is On, your
computer’s screen saver will not be activated. A type B USB
mouse cable must be connected to use this feature. See page 11
for details. This feature is available for PC Computer RGBHV and
VESA sources only. It is not supported on the Macintosh plat-
form.
Display Messages
This setting toggles between On and Off. When this feature is On,
status messages such as “No signal detected” or “Standby
Active” appear in the lower-right corner of the screen. Click the
left or right mouse button to turn this feature off and not see sta-
tus messages.
Display Startup Screen
This setting toggles between On and Off. When this feature is On,
the startup screen appears when the projector starts up and
remains until an active source is detected. The startup screen con-
tains contact information. Click the left or right mouse button to
turn this feature off and display a plain black or blue screen
instead of the startup screen.
37
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Language Menu
>
Display Audio Image Controls Language Status
>
English
Francais
Deutsch
~
Espanol
FIGURE 27
Language menu
You can display the on-screen menus in English, French, German,
Spanish, Chinese or Japanese.
• Move the cursor to the language you want, then click the left or
right mouse button. The menus redraw immediately.
Status Menu
This is a read-only window for informational purposes. To dis-
play the status window, select Show status from the menu, then
click the left or right mouse button. To remove the window, click
the left or right mouse button.
Display Audio Image Controls Language Status
>
Show status
Lamp hours used
Computer resolution
Horizontal refresh rate
Vertical refresh rate
Mute status
0039
1024x768
60.03 KHz
75.04 Hz
off
Source
computer VESA
internal
1.0
Speakers
Software version
Startup screen version
Boot version
1.0
1.0
CableWizard version
1.0
FIGURE 28
Status menu
38
Lamp hours used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in
use. After 1,900 hours, the message “Change Lamp” temporarily
appears on the screen when the projector is turned on. Change
the bulb when the brightness is no longer acceptable. See
“Replacing the Projection Lamp” on page 41 for details.
Computer resolution
Shows your computer’s resolution setting. To change this, go to
your computer’s Control Panel and adjust the resolution in the
Display tab. See your computer’s user’s guide for details.
Horizontal refresh rate
The time period that one horizontal line is displayed.
Vertical refresh rate
The time period that one video frame is displayed.
Mute status
Indicates if the audio is muted. Mute is only available on the
optional remote.
Source
Indicates the active source: Computer RGBHV, Computer VESA,
Computer M1 Analog or Computer M1 Digital, Computer
CableWizard, Component Video, Composite Video, or S-Video.
Speakers
Indicates if external speakers are connected.
Software version
Indicates the projector’s software version. This information is
useful when contacting Technical Support.
Startup screen version
Indicates the projector’s startup screen version. This information
is useful when contacting Technical Support.
Boot version
Indicates the projector’s boot software version. This information
is useful when contacting Technical Support.
CableWizard version
Indicates the CableWizard’s software version. This information is
useful when contacting Technical Support.
39
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
40
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•clean the lens
•replace the projection lamp
•replace the batteries in the remote
•use the security lock feature
•troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner.
• Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular
motion.
3 If you don’t intend to use the projector immediately, replace
the lens cap.
Replacing the Projection Lamp
hours the lamp has been in use. After 1,900 hours, the message
“Change Lamp” temporarily appears on the screen when the pro-
jector is turned on. Replace the lamp when the brightness is no
longer acceptable. You can order new lamp modules from your
InFocus dealer. See “Accessories” on page 50 for information.
WARNING: To avoid burns,
allow the projector to cool for at
least 30 minutes before you open
the lamp module door. Never
extract the lamp module while the
lamp is operating.
1 Turn off the projector by unplugging the power cord.
2 Wait 30 minutes to allow the projector to cool thoroughly.
3 Use a screwdriver to remove the seven screws on the back of
the projector (Figure 29).
41
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
WARNING: Be extremely careful
when removing the lamp module.
In the unlikely event that the bulb
ruptures, small glass fragments
may be generated. The lamp
module is designed to contain
these fragments, but use caution
when removing the lamp module.
FIGURE 29
Removing the screws on the lamp door
4 Loosen the three captive screws on the outside of the module.
CAUTION: Never operate the
projector with the lamp door open
or removed. This disrupts the air
flow and causes the projector to
overheat.
FIGURE 30
Loosening the screws on the lamp module
42
5 Lift and grasp the metal handle and pull the module out (Fig-
ure 31). Dispose of the lamp module in an environmentally
proper manner.
FIGURE 31
Removing the lamp module
6 Install the new lamp module, being sure to align the connec-
tors properly.
WARNING: Do not drop the
lamp module or touch the glass
bulb! The glass may shatter and
cause injury.
7 Push the module in until it is flush with the case of the projec-
tor.
8 Tighten the three screws on the outside of the module.
9 Replace the lamp door and re-install the seven screws.
10 Plug in the power cord and press the power button to turn the
projector back on. The lamp hour counter in the Status menu
is automatically reset to zero.
43
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of opera-
tion.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Slide the battery cover off the end of the remote.
3 Remove the old batteries and dispose of them in an environ-
mentally proper manner.
4 Install two new AA alkaline batteries. Make sure you install
each in the correct direction.
Using the Security Lock
The projector has a security connector for use with a PC Guardian
Cable Lock System (Figure 32). See “Optional Accessories” on
page 50 for ordering information. Refer to the information that
came with the lock for instructions on how to use it to secure the
projector.
FIGURE 32
Installing the security lock
44
Troubleshooting
Problem: Nothing on projection screen
•Make sure that the power cord is properly connected to a fully
functional AC electrical outlet. Make sure that the power cord
is also properly connected to the projector.
•If the projector is plugged into a power strip, make sure the
power strip is turned on.
lens at the front of the projector.
•Make sure the lamp is switched on.
•Check the projector’s lamp to ensure that it is securely con-
nected in the lamp module. See “Replacing the Projection
Lamp” on page 41.
•Make sure that the cables do not have any bent pins.
Problem: Color or text not being projected
•You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 28 for more infor-
mation.
Problem: The screen resolution is not right
no greater than 1280x1024.
Problem: Image isn’t centered on the screen
•Move the projector to reposition the image.
•Be sure the projector is at a 90 degree angle to the screen.
•Verify that the cables are connected correctly. See page 12
through page 14 for connection procedures.
•Verify that the proper input source is connected and active. See
“Source (keypad only) or Comp and Video (remote only)” on
page 26.
45
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
•You might need to turn everything off and power up the
equipment again in the proper order. Refer to your com-
puter’s documentation to determine the correct order.
•Make sure your laptop’s external video port is turned on. See
the “Portable and Laptop Activation Chart” on page 52 or
your computer’s manual for details.
•Make sure your computer’s video board is installed and con-
figured correctly.
•Make sure your computer has a compatible video board. The
projector isn’t CGA, EGA or SXGA compatible.
If you’re using Windows 98:
1 Open “My Computer” icon, the Control Panel folder and
then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1280x1024 or less.
Problem: Image is too wide or narrow for screen
•Adjust the zoom or projector placement.
•Adjust the resolution of your video card if it’s greater than
1280x1024.
Problem: Image is out of focus
•Turn the projection lens to focus the image.
•Make sure the projection screen is at least 3.3 feet (1 m) from
the projector.
Problem: Image and menus are reversed left to right
•Rear projection mode is probably turned on. Turn Rear Projec-
tion off in the Controls menu. The image should immediately
return to forward projection. See “Rear Projection” on
page 36.
46
Problem: the projector displays vertical lines, “bleeding” or
spots
•Adjust the brightness. See “Brightness” on page 28.
Problem: no sound
•Adjust volume.
•Verify audio/input connections. Make sure you have selected
the proper audio source. See “Audio Source Select” on
page 31.
•Adjust audio source.
Problem: Image is “noisy” or streaked
Try these steps in this order.
2 Turn Auto Image off and then back on again. See “Auto
Image” on page 32.
3 Turn Auto Image off and adjust the synchronization and track-
ing manually to find an optimal setting. See “Manual Sync”
on page 33 and “Manual Tracking” on page 33.
•The problem could be with your computer’s video card. If
possible, connect a different computer.
Problem: Projected colors don’t match the computer or video
player’s colors
•Just as there are differences in the displays of different moni-
tors, there are often differences between the computer image
and the projected image. Adjust the brightness, tint and/or
“Tint” on page 28 and “Contrast” on page 28.
Problem: Lamp seems to be getting dimmer
•The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 41.
47
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Problem: Lamp shuts off
•A minor power surge may cause the lamp to shut off. Unplug
the projector, wait at least a minute, then plug it back in.
•Make sure the vents are not blocked.
The most current troubleshooting information can be found in
the Service and Support section of our website at
Library, FAQs, and support contacts including a technical sup-
port e-mail form.
Before calling your dealer or InFocus Technical Support for assis-
tance, please have the following information available:
•the projector’s serial number (located on the bottom label)
•the resolution of your computer.
Call InFocus Technical Support at 1-800-799-9911 between 6 a.m.
and 6 p.m. PST, Monday through Friday. Service is available in
North America after hours and on weekends for a fee at
1-888-592-6800.
In Europe, call InFocus in The Netherlands at (31) 35-6474010
between 8 a.m. and 6 p.m. Central European Time.
In Asia, call (65) 332-0659 between 9:30 a.m. and 5:30 p.m.
Or, send us an e-mail at [email protected]
48
APPENDIX
Specifications
The projector must be operated and stored within the tempera-
ture and humidity ranges specified.
Te m p e r a t u re
Operating
50 to 104° F (10 to 40° C)
-4 to 158° F (-20 to 70° C)
Non-operating
Humidity
Operating and non-oper.
10% to 90% relative humidity, non-condensing
Dimensions
16.5 x 8.25 x 19.5 inches (cm)
Weight
25.5 lbs. (11.5 kg) unpacked
Altitude
Operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)
Non-operating
Optics
Focus Range
3.3 - 40 feet (10-12 m)
230-watt UHP lamp
Lamp
Type
Input Power Requirements
100-120VAC 5A;50/60Hz
200-240VAC 3A; 50Hz
49
A
p
p
e
n
d
i
x
Accessories
Standard Accessories
(ship with the projector)
Part Number
590-0275-xx
SP-LAMP-LP9
110-0332-xx
340-0445-xx
010-0264-xx
010-0265-xx
210-0053-xx
210-0119-xx
Laser Pro Remote Control
Projection Lamp Module (one in projector)
Shipping Box
Lens Cap
User’s Guide
User’s Guide CD
A/V cable
VESA cable
Power Cords (one ships with projector, type depends on country)
NOTE: Use only InFocus
North American Power Cord
Australian Power Cord
UK Power Cord
210-0023-xx
210-0027-xx
210-0028-xx
210-0029-xx
210-0030-xx
210-0031-xx
approved accessories. Other
products have not been tested with
the projector.
European Power Cord
Danish Power Cord
Swiss Power Cord
Optional Accessories
NOTE: You can purchase these
items by contacting your dealer or
InFocus Catalog Sales at
ATA Shipping Case
CA-C204
900 Series Long Throw Zoom Lens
900 Series Wide Angle Zoom Lens
HW-LENS-LL02
HW-LENS-LW01
HW-LENS-LR01
1-800-660-0024.
900 Series Ultra Wide Angle Lens (rear projec-
tion)
M1-DA Digital Computer Cable w/ USB
M1 to VGA/USB-Analog Computer Cable
Macintsoh adapter
SP-DVI-D
SP-DVI-A
SP-MACADPT
SP-CW3
CableWizard 3
CableWizard 2
SP-CW2
CableWizard Lite
SP-CW2LITE
SP-CW2EXT
CableWizard Extension Cable, non-plenum rated,
60.7 ft
CableWizard Extension Cable, plenum-rated,
60.7 ft
SP-CW2EXTP
CableWizard Extension Cable (70’)
3rd year Advantage Service Plan
Projector Cable Cover
SP-CW2-IEXT
EW-LP9xx-12
50
HW-CBLCVR9XX
Ceiling Mount Kit (10” base box)
Ceiling Mount Adapter Plate (10” base box)
Ceiling Mount Adapter Plate (12” base box)
LiteMount False Ceiling Plate
SP-CEIL-LM9x
SP-CEIL-P9
SP-CEIL-P9A
SP-LTMT-PLT
SP-LTMT-EXT
SP-LTMT-EXT-GRAY
SP-CWWALL
SP-WIREM
LiteMount Pipe Tubing Extension-Black
LiteMount Pipe Tubing Extension-Gray
CableWizard Extension Cable Wall Plate
Wired Remote Cable
GyroMouse Pro RF Remote (40’, not limited to
HW-RF-GPRO
line of sight)
RemotePoint RF Remote Control w Laser Pointer HW-RF-REMLSR
GyroMouse Presenter RF Remote Control
Full-Feature LaserPro Remote Control
Executive Plus Remote Control (4 Button)
Executive Remote IR Receiver
HW-RF-GPRES
HW-LASERPRO
HW-EXPLUS
HW-EXRCVR
SP-LOCK
PC Guardian Projector Cable Lock
40” Diagonal Portable Projection Screen
50” Diagonal Portable Projection Screen
60” Diagonal Portable Projection Screen
84” Diagonal Pull Down Projection Screen
Portable Projector Stand
HW-PORTSCR40
HW-PORTSCR50
HW-DLXSCRN
HW-WALLSCR84
SP-STND
Deluxe Wheeled Projector and Computer Cart
HW-CART
Appian Traveler (Digital/Analog CardBus PC
Card)
SP-DVI-CARD
eBeam (Web Enabled Electronic Meeting
Assistant
HW-EBEAM
BNC to BNC Cable (Composite Video)
5BNC to 5BNC Cable
SP-BNC
SP-5TO5
5BNC to HD15 Cable (VESA)
S-Video Cable
SP-5TO15
SP-SVIDEO
SP-MAC15
SP-MAC50-D
SP-MAC50-I
SP-VGA15
SP-VGA50-D
SP-VGA50-I
15’ Mac Extension Cable
50’ Mac Cable-Domestic
50’ Mac Cable-International
15’ VGA Extension Cable
50’ VGA Cable-Domestic
50’ VGA Cable-International
51
A
p
p
e
n
d
i
x
Portable and Laptop Activation Chart
Many laptop computers do not automatically turn on their exter-
nal video port when a projector is connected. Activation com-
mands for some laptop computers are listed in the following
table. (If your computer is not listed or the given command does
not work, refer to the computer’s documentation for the appro-
priate command.) On many laptops, the activation function key
is labeled with an icon, for example
or the text CRT/LCD.
NOTE: Usually, pressing the key
commands once activates the
external video port, pressing it
again activates both the external
Key command to
Key command to
de-activate port
Computer
Acer
activate port
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
AST* **
and internal ports, and pressing it
a third time activates the internal
port. Refer to your computer’s
documentation for details on your
specific model.
FN-F5
FN-F5
type from A:/IVGA/CRT
FN-F12
type from A:/IVGA/CRT
FN-F12
AMS
FN-F2
FN-F2
AMT
AT&T
setup screen
setup screen
FN-F3
FN-F6
FN-F3
FN-F6
Advanced Logic
Research
Ctrl-Alt-V
Ctrl-Alt-V
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
setup VGA/
Conf.Simulscan
Conf.Simulscan
Ambra**
FN-F12
FN-F12
FN-F5
FN-F5
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
Amrel* **
Apple
Aspen
Award
BCC*
see Mac Portable and Mac PowerBook
automatic
FN-F6
automatic
FN-F6
automatic
reboot computer
52
Key command to
activate port
Key command to
de-activate port
Computer
Bondwell
LCD or CRT options after
bootup
reboot for LCD or CRT
options to appear
Chaplet**
setup screen
FN-F6
setup screen
FN-F6
FN-F4
FN-F4
Chembook
Commax
FN-F6
FN-F6
Ctrl-Alt-#6
Ctrl-Alt-<
FN-F4
Ctrl-Alt-#5
Ctrl-Alt->
FN-F4
Compaq* **
automatic
mode/? (for setup option)
automatic
automatic
mode/? (for setup option)
automatic
Compuadd* **
Data General
Alt-F for screen setup
option
Alt-F for screen setup
option
Ctrl-Alt-Command
Ctrl-Alt-Command
reboot
Data General
Walkabout
2 CRT/X at DOS prompt
Datavue
DEC**
Ctrl-Shift-M
FN-F5
Ctrl-Shift-M
FN-F5
FN-F4
FN-F4
Dell**
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
FN-F8
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-D
FN-D
FN-F12
FN-F12
Digital*
automatic
reboot
FN-F2
FN-F2
Dolch
Epson
Everex*
For-A
dip switch to CRT
dip switch to CRT
setup screen option
Ctrl-Alt-Shift-C
FN-F10
dip switch to LCD
dip switch to LCD
setup screen option
Ctrl-Shift-Alt-L
Fujitsu
53
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Gateway
FN-F3
FN-F3
FN-F1
FN-F1/FN-F1 again simul-
taneous
Grid* **
FN-F2, choose auto or
simultaneous
FN-F2
Ctrl-Alt-Tab
Ctrl-Alt-Tab
FN-F7
Hitachi
FN-F7
Honeywell
Hyundai
FN-F10
FN-F10
setup screen option
automatic
setup screen option
warm reboot
FN-F2
IBM 970*
IBM ThinkPad**
reboot, enter setup menu
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor plugged
in
unplug monitor
Kris Tech
FN-F8
FN-F8
FN-T
Leading Edge
FN-T
Mac Portable
100
no video port: not compatible
Mac PowerBook
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165, 180,
520, 540, 5300
Control Panel folder, Pow- warm reboot
erBook Display folder;
Activate Video Mirroring
210, 230, 250,
270, 280, 2300
requires Apple Docking Station or Mini Dock
Magitronic
FN-F4
FN-F2
FN-F4
FN-F1
Mastersport
54
Key command to
activate port
Key command to
de-activate port
Computer
Micro Express*
Micron
automatic
warm reboot
FN-F2
FN-F2
Microslate*
Mitsubishi
NCR
automatic
warm reboot
SW2 Off-On-On-On
setup screen option
setup screen option
LCD at the DOS prompt
FN-F3
SW2 On-Off-Off-Off
setup screen option
setup screen option
CRT at the DOS prompt
FN-F3
NEC* **
Olivetti*
automatic
automatic
FN-O/*
FN-O/*
Packard Bell* **
FN-F0
FN-F0
Ctrl-Alt-<
Ctrl-Alt->
Panasonic
Prostar
Samsung*
Sanyo
FN-F2
FN-F2
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to CRT
Ctrl-Shift-M
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to LCD
Ctrl-Shift-M
Sharp
Sun SPARC-
Dataview
Tandy**
Ctrl-Alt-Insert
setup screen option
FN-F5
Ctrl-Alt-Insert
setup screen option
FN-F5
Tangent
Texas Instru-
ments*
setup screen option
setup screen option
Top-Link* **
setup screen option
FN-F6
setup screen option
FN-F6
Toshiba* **
Ctrl-Alt-End
FN-End
Ctrl-Alt-Home
FN-Home
FN-F5
FN-F5
setup screen option
FN-F7
setup screen option
FN-F7
Twinhead*
WinBook
FN-F5
FN-F5
Automatic
Ctrl-Alt-F10
Automatic
Ctrl-Alt-F10
55
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Wyse
software driven
FN-F10
software driven
FN-F10
Zenith**
FN-F2
FN-F2
FN-F1
FN-F1
Zeos**
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
*
These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depend-
ing on the computer model.
56
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer Pow-
erBooks—see below) on, the projector displays the same informa-
tion that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip, then click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as
the primary monitor.
4 Restart the PowerBook.
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and
Sound.
2 In the Resolution list, choose the SimulScan mode, then click
OK.
3 If this changes your display settings, a dialog box appears.
Click OK to confirm the change.
57
A
p
p
e
n
d
i
x
Projected Image Sizes
Table 4:
NOTE: Use the tables to help you
Diagonal Image Size and Width at Maximum and Minimum Distance
to Screen-Short Throw Lens
determine projected image sizes.
Distance to screen
Diagonal
Image Size
(inches)
Maximum
distance
(feet)
Minimum
Distance
(feet)
Image Width
(inches)
300
240
180
144
120
96
240
192
144
115
96
33
27
20
16
13
11
8
28
22
17
13
11
9
77
72
58
7
60
48
7
6
48
38
5
4
NOTE: Visit our website at
image size calculator. It is located
in the Technical Library in the
Service and Support section.
Table 5:
Diagonal Image Size and Width at Maximum and Minimum Distance
to Screen-Long Throw Lens
Distance to screen
Diagonal
Image Size
(inches)
Maximum
distance
(feet)
Minimum
Distance
(feet)
Image Width
(inches)
300
240
180
144
120
96
240
192
144
115
96
86
69
52
41
34
28
21
17
14
51
41
31
24
20
16
12
10
8
77
72
58
60
48
48
38
58
RS232 Terminal Specifications
Communication configuration
To control the projector from an LCD control panel or terminal
software, connect a null modem type RS232 cable and set your
computer’s serial port settings to match this communication con-
figuration:
Setting
Value
19,200
8
Bits per second
Data bits
Parity
None
1
Stop bits
Flow control
Emulation
None
VT100
Here are the pinouts of the RS232 connector (outputs and inputs
are relative to the projector):
6
9
1. Not used
6. Not used
2. Receive data
(input)
7. Ready to
send (output)
3. Transmit (output)
4. Not used
8. Not used
9. Not used
1
5
5. Ground
Command format
All commands consist of 3 alpha characters followed by a
request, all enclosed in parentheses. The request can be a read
request (indicated by a “?”) or a write request (indicated by 1 to 4
ASCII digits).
A read request format: (AAA?) where
(
starts the command
AAA denotes the command
?
)
denotes the read request
ends the command
59
A
p
p
e
n
d
i
x
A read command returns the range and the current setting, for
example:
Function
Brightness
Volume
Command
(BRT?)
Response
(0-22, 10)
(0-80, 0)
(VOL?)
Lamp hours
(LMP?)
(0-9999, 421)
A write request example: (AAA####) where
starts the command
AAA denotes the command
(
####
denotes the value to be written
(leading zeros not necessary)
)
ends the command
Some commands have ranges, while others are absolute. If a
number greater than the maximum range is received, it is auto-
matically set to the maximum number for that function. If a com-
mand is received that is not understood, a “?” is returned. With
absolute settings, “0” is off, 1-2147483647 is on. The one exception
is the Power command, where 0 is off and 1 is on.
NOTE: To assure the projector
can process a command, wait 3
seconds before entering the next
command.
Function
Brightness
Freeze
Command
(BRT10)
Response
Sets the brightness to 10
Freezes the display
Turns power off
Turns power on
?
(FRZ1)
Power
(PWR0)
Power
(PWR1)
Power
(PWR9999)
Supported commands
Comma
nd
Function
Power
Range
0-1
PWR
LMP
STB
Lamp Hours (Read only)
Standby
0-9999
0-1
Freeze
FRZ
0-1
60
Brightness
Contrast
BRT
0-63
0-63
0-63
0-127
0-63
0-1
CON
TNT
CLR
CON
RST
Tint
Color
Contrast
Reset All
Auto Source Select Control
Default Source
ASC
DSC
0-1
0-9
0 = Computer RGBHV
1 = Computer VESA
2 = Computer M1
analog
3 = Computer M1
digital
4 = Computer
CableWizard
5 = Feature Card Analog
(not currently available)
6 = Feature Card Digital
(not currently available)
7 =Component Video
8 = Composite Video
9 = S-video
Source
SRC
0-9
(same designations as
Default Source)
Volume
VOL
MTE
BAL
FAD
IPO
0-100
0-1
Mute
Balance
0-60
0-60
0-2
Fade
Image Position
Treble
TRB
BAS
MTE
AIM
ARZ
MSS
MTS
HPS
0-100
0-100
0-1
Bass
Mute
Auto Image
0-1
Resize
0-1
Manual Sync Setting
Manual Tracking Setting
Horizontal Position Setting
0-20
800-2112
0-256
61
A
p
p
e
n
d
i
x
USB:Inhibit Screen Saver
USB:Mouse Button
Current
UIS
0-1
0-1
0-6
0-28
UMB
USB
VPS
VSU
Vertical Position Setting
Video Standard
0-6
0 = NTSC
1 = PAL
2 = PAL-M
3 =PAL-N
4 = SECAM
5 = NTSC4.43
6 = PAL-60
Language
LAN
0-5
0 = English
1 = French
2 = German
3 = Spanish
4= Chinese
5= Japanese
Video Connection Status
TV Connector Control
Color Temperature
System State
VCS
TVC
TMP
SYS
0-2147483647
0-3
0-25
0-2147483647
Sharpness
SHP
SBT
0-10
Standby Time
Power Off Time
Plug and Play
0-7
POT
PAP
0-7
0-1
Overscan
OVS
MNU
DSU
DMG
BSC
ASL
0-1
Menu
0-1
Splash Screen
Display Message
Blank Screen Color
Audio Select
0-1
0-1
0-1
0-3
Audio Mode
AMO
ACS
CEL
REA
0-2147483647
0-2147483647
0-1
Audio Connection Status
Ceiling
Rear Project
0-1
62
C
cables
INDEX
composite video 13
A
accessories, ordering 50
activation commands for laptop com-
adjusting
power 50
balance 31
S-video 13
brightness 25, 28
color 29
contrast 28
extension cable 50
ceiling-mounted projection 36, 50
centering the image 34
fade 31
tint 28
volume 26, 30
altitude limits 49
assistance. See Technical Support
audio cable, connecting 11, 12, 14
Audio menu 30
Audio menu options
Balance 31
not displayed 45
compatibility
Bass 30
IBM-compatible 1
Macintosh 1
Fade 31
Treble 30
Volume 30
Auto Image 32
Auto Source Select 36
B
balance, adjusting 31
audio cable 11, 12, 14
bass 30
Blank Screen 29
BNC connection 14
Brightness buttons 25
brightness, adjusting 25, 28
buttons on keypad
Brightness 25
Freeze 25
computers 12
power cord 16
remote 12
video player 13–14
connecting RS-232 cable 12
connector panel
Laser 25
Menu 25
Power 25
audio out 15
Source 26
remote cable 15
Standby 26
contrast, adjusting 28
Volume 26
63
I
n
d
e
x
Controls menu 35
Controls menu options
Auto Source Select 36
Ceiling Projection 36
Default Source 36
image
Display Messages 37
Display Startup Screen 37
Plug and Play 36
adjusting 16, 19
focusing 20
Rear Projection 36
Standby Time 35
Video Standard 35
not centered 45
D
Default Source 36
Display menu 28
Display menu options
Blank Screen 29
Brightness 28
size 5, 58
Color 29
Contrast 28
streaked 47
Reset All 29
Sharpness 29
Tint 28
Display Messages 37
Display Startup Screen 37
displaying
Image menu 32
Image menu options
Manual Sync 33
Manual Tracking 33
Overscan 32
on-screen menus 25
startup screen 37
status messages 37
E
Resize 32
extension cable 50
Vert. Position 34
Zoom 34
external speakers, connecting 15
F
K
fade, adjusting 31
keypad 24
focusing the image 20
Freeze button 25
freezing the projected image 25
fuzzy lines 33
H
HDTV 1, 13, 32
64
L
lamp
NTSC video 35
ordering 50
O
replacing 41
turns off unexpectedly 48
changing language of 38
Controls menu 35
Display menu 28
lamp hour counter 39
Language menu 38
language, selecting for menus 38
laptop computers
activation sequence to allow
compatibility 12
connecting 12
Image menu 32
Language menu 38
making changes to menu
laser pointer 25
Status menu 38
lens
cap 50
cleaning 41
leveling the projector 20
LP930
PAL video 28, 35
Plug and Play 36
project from behind the screen 36
setting up 5
power cord
connecting 16
specifications 49
turning off 17
ordering 50
power up sequence 16
PowerPoint slides, advancing with the
remote 12
turning on 16
M
project from behind the screen 36
Macintosh computers
compatibility 1
connecting 11
Menu 25
Menu button 25, 27
menus. See on-screen menus
monitor, projected colors don’t match
47
mouse
connecting 12
connecting USB type B 11
65
I
n
d
e
x
R
rear projection 36
remote control
in USA 4
advancing PowerPoint slides
with 12
connecting 12
temperature limits 49
controlling the computer with 12,
22
laser pointer 23, 25
replacing the batteries 44
using 22, 24
test pattern 45
text not visible 45
tint, adjusting 28
replacing projection lamp module 41
re-positioning the image on the screen
34
troubleshooting 45
turning off the projector 17
turning on the projector 16
resetting adjustments 29
resizing video 32
U
resolution 1
USB mouse 12
RGBHV connection 11
RS-232 cable
connecting 12
vertical lines displayed 33, 47
video resizing 32
S
safety guidelines iii
SECAM video 35
security lock 44, 51
sharpness 29
video standards 35
SimulScan, using with PowerBooks 57
Source button 26
specifications 49
Standby button 26
Standby Time 35
startup screen 37
Status menu 38
adjusting 26
Volume buttons 26
volume, adjusting 30
W
widescreen video 33
S-video
Z
connecting 13
Zoom, digital 34
zooming the image 20
66
LIMITED WARRANTY
InFocus Corporation (“InFocus”) warrants that each LP930 (“the Product”) sold hereunder will conform to and function in
accordance with the written specifications of InFocus. Said limited warranty shall apply only to the first person or entity
that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said warranty
shall continue for a period of two (2) years from the date of such purchase. The standard limited warranty excludes the
lamps in projectors after 90 days and the accessories after one year. InFocus does not warrant that the Product will meet the
specific requirements of the first person or entity that purchases the Product for personal or business use. InFocus’ liability
for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the pur-
chase price of the Product, at InFocus’ sole option. Replacement Product may be re-furbished in “like-new” condition, at
InFocus’ sole discretion. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at
the Purchaser’s sole cost and expense, to InFocus or to any authorized InFocus service center provided, and the Product
must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the
dealer’s name; and (iii) the model and serial number of the Product. When sending your unit in for repair, please ship your
unit in its original packing material or an InFocus approved ATA Shipping Case, or have a professional packaging com-
pany pack the unit. Please insure your shipment for its full value. A return authorization number, issued by the InFocus
customer service department, must also be clearly displayed on the outside of the shipping carton containing the Product.
Note: Remanufactured Products are exempt from the foregoing Limited Warranty. Please refer to the Remanufactured
Product Warranty for applicable warranty information.
WARRANTY LIMITATION AND EXCLUSION
InFocus shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations,
or service other than by InFocus or its authorized agents, causes other than from ordinary use or failure to properly use the
Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO
YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE
PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR
LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING INFOCUS’ LIABILITY.
NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE
BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPE-
CIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Part Number 010-0264-00
|