Insignia Indoor Furnishings NS WD1450 User Manual
USER GUIDE  
Espresso Finish Closed Cabinet  
TV Stand  
for TVs up to 50”/95 lbs  
NS-WD1450/NS-WD1450-C  
SAFETY INFORMATION AND SPECIFICATIONS....2  
PACKAGE CONTENTS: PARTS.....................................3  
PACKAGE CONTENTS: HARDWARE..........................4  
ASSEMBLY INSTRUCTIONS.........................................5  
CARE AND MAINTENANCE...................................... 19  
Before using your new product, please read these instructions to prevent any damage.  
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
PACKAGE CONTENTS: PARTS  
Make sure that you have all the parts necessary to assemble your new TV stand. While not all parts are  
labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts  
from each other. Use this part identification to help identify similar parts.  
A
B
C
D
E
F
G
H
I
Right End  
Left End  
1
1
1
1
1
1
1
2
2
2
K
L
Small Adjustable Shelf  
Long Skirt  
2
1
2
1
2
1
2
2
2
Right Upright  
Left Upright  
Top  
M
O
P
Short Skirt  
Top Molding  
Long Brace  
Bottom  
Back  
Q
R
Short Brace  
Side Brace  
Outer Back  
Door  
S
Inner Base Block  
Outer Base Block  
T
J
Large Adjustable Shelf  
E
O
A
G
H
C
K
J
D
J
H
K
F
B
P
R
P
T
M
Q
I
L
I
R
S
M
T
www.insigniaproducts.com  
3
 
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
PACKAGE CONTENTS: HARDWARE  
Note: The table below shows the required hardware. You may receive extra hardware.  
Make sure that you have all the hardware necessary to assemble your new TV stand.  
Label  
U
Hardware  
Qty.  
8
Label  
CC  
Hardware  
Metal pin  
Qty.  
24  
Sauder  
twist-lock®  
fasteners  
Rubber sleeve  
Warning label  
DD  
EE  
16  
1
V
Hidden cam  
2
2
Cam dowel  
W
FF  
GG  
HH  
10  
14  
2
Large metal  
bracket  
X
Y
1
Black 1-7/8” flat head screw  
Silver 1-1/8” flat head screw  
Metal bracket  
Hinge  
18  
Gold 1” machine screw  
Z
4
II  
37  
AA  
BB  
Knob  
2
4
Black 9/16” large head screw  
JJ  
8
Felt discs  
Black 1/2” flat head screw  
Nail  
KK  
20  
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
www.insigniaproducts.com  
4
 
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
ASSEMBLY INSTRUCTIONS  
Step 1: Preparing the right and left ends and the uprights  
Caution: Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your stand.  
• Push a Sauder twist-lock® fastener (U) into the large holes in the right and left ends (A and B) and uprights (C  
and D).  
NOTE: Do not tighten the Sauder twist-lock® fasteners at this time.  
U
B
A
D
C
You’ll need:  
U (8)  
www.insigniaproducts.com  
5
 
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 2 Preparing the short brace  
:
•
Push two hidden cams (V) into the short brace (Q). Then, insert the metal end of a cam dowel (W) into  
each hidden cam (V).  
NOTE: Do not tighten the hidden cams in this step.  
Q
Arrow  
V
W
Arrow  
Insert the cam dowel into the hidden cam.  
You’ll need:  
W (2)  
V (2)  
www.insigniaproducts.com  
6
 
ESPRESSO FINISH CLOSED CABINET TV STAND  
Step 3 Preparing the top  
:
•
Fasten the top molding (O) to the top (E). Use six silver 1-1/8” flat head screws (GG).  
Finished surface  
s
e
l
o
h
h
t
i
w
e
c
a
f
O
r
u
E
S
Curved edge  
You’ll need:  
GG (6)  
Phillips screwdriver  
www.insigniaproducts.com  
7