Insignia Stereo System NS H2002 User Manual

The speaker to listener dimensions (DIM) shown in the above right picture is used for correct  
setup of the surround system. For more information, seeSetting up the speakers.  
Notes:  
1 Connect the video  
For a good picture quality, use the RCA video cable.  
Remote control  
Parental lock is NOT active  
The Parental lock is active  
Notes:  
Do not connect more than one speaker to any one pair of +/- speaker terminals  
Do not connect speakers with an impedance lower than the speakers supplied  
The parental lock must be active for the rating level to function  
The parental lock must not be active to changes the rating level  
If you forget the password, enter 76418 while the player is in NO Disc mode  
User Guide  
Installing your DVD home theater system  
Install your home theater on a stable flat surface. There must be sufficient room in  
front of your home theater for the disc tray to open. Positon your home theater so  
that it can have a direct line of signal to the remote control.  
Selecting the playing source  
200-Watt 5.1 Home Theater System I NS-H2002  
Do not expose your home theater to extremes of temperature or humidity.  
Avoid placing your home theater on a hot surface such as on top of other hot running  
equipment. Make sure that there is adequate ventilation to your home theater.  
Caution: Do not install this home theater in a confined space such as a bookcase.  
Note: Connect the AV cord only after the speakers, antenna, and all optional equipment have been connected.  
Never make or change any connections with power turned on.  
authorized by Macrovision Corporation and is intended for home and other limited viewing  
INTRODUCTION  
uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or  
disassembly is prohibited. Consumers should note that not all high definition television sets  
are fully compatible with this product and may cause artifacts to be displayed in the picture.  
In case of 525 or 625 progressive scan picture problems, we recommend that the user switch  
the connection to the “standard definition” output. If there are questions regarding our TV  
set compatibility with this model 525p and 625p DVD player, contact our customer service  
center. U.S. Patent Nos. 4,631,603; 4,819,098; 4,907,093; 5,315,448; and 6,516,132  
Congratulations on your purchase of a high-quality Insignia product. Your NS-H2002  
represents the state of the art in home theater design and is designed for reliable and  
trouble-free performance.  
Select the source files that you want to play between Disc and USB. To access files in a USB  
device, make sure your USB devices is connected to the USB jack on the front panel.  
Notes:  
Maintaining  
Cleaning discs  
This unit can not support NTFS format. If the USB flash drive does not work on it. Please check the USB flash  
drive file system and format it with FAT or FAT32.  
Picture freezing, sound skipping, or repeating can occur if the disc inside theplayer  
is dirty.  
When a disc gets dirty, clean it with a cleaning cloth. Wipe the disc fromthe center  
out.  
Do not wipe in a circular motion. Circular scratches can cause picture distortionor  
render the disc unplayable.  
SAFETY INFORMATION  
Electric shock warning  
Not all MPEG 4 files can be played through the USB jack due to the limited transmission speed  
For a higher quality picture, purchase an S-Video cable, or for the best picture quality, purchase  
a component video cable.  
Selecting languages for menus  
You can select different languages for the Setup Menu.You can also select different languages  
for audio, subtitle, and menu recorded on the DVD.  
Front  
Caution: Do not use solvents, commercially available cleaners, or antistatic spray intended for analog discs.  
Warning: To reduce the risk of electric shock, do not remove the cover or back. There are no user-serviceable  
parts inside. Refer servicing to qualified service personnel.  
Turning on your DVD home theater system  
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the  
user to the presence of uninsulated dangerous voltage within your home theater’s enclosure that  
may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation  
point within an equilateral triangle is intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in the literature accompanying your home  
theater. Warning  
To start your home theater the first time:  
1.  
Plug in your home theater. The standby indicator on the front panel lights up.  
2.  
Press Standby/On (on your home theater or on the remote control). After a few  
seconds the display shows NO DISC.  
CAUTION: To prevent fire or electric shock hazard, do not expose this home theater to rain or  
moisture.  
3.  
Turn on your television and select the AV input that your home theater is connected  
to.  
Press Eject (on your home theater or on the remote control). The disc tray opens.  
Place a DVD in the disc tray, then press Eject. The player reads the disc and starts  
playback. Before the movie starts to play, a menu appears.  
Select PLAY MOVIE and press OK. The movie starts.  
Although you can watch a movie immediately, to get the best results from your  
home theater, press STOP.  
Complete the following system setup options. This sets up all the functions on your  
home theater. You only need to do this when you first set up your home theater.  
OSD LANG: Select the Setup menu language.  
AUDIO LANG: Select the audible language heard during playback.  
SUBTITLE LANG: Select the subtitle language displayed on the television screen.  
DISC MENU: Select the disc menu language.  
WARNING:Your home theater should not be exposed to water (dripping or splashing) and no objects filled with  
liquids, such as vases,should be placed on your home theater.  
4.  
5.  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Standby/On - press to turn your home theater on or to standby mode  
Standby Indicator - Power On/Off Mode: no light; Standby Mode: red LED  
Disc Tray - place a DVD or CD, label side up, into this tray  
Infrared receiver - receives the signal from the remote control  
VFD Display Area - displays status messages  
PHONES - plug standard headphones into this jack  
USB jack - plug external USB devices into this jack  
VOLUME - adjusts the volume. Turn clockwise to increase the volume and counter-  
clockwise to decrease the volume  
Eject/ Stop Eject - opens or closes the disc loading tray in stop or no disc mode;  
Stop - Stops playing  
1) Starts playback in DVD mode, 2) Pauses playback in DVD mode  
DVD, VCD, or CD mode: 1) press to skip to the previous chapter or track; 2) press  
and hold to search forward; Tuner mode - tunes channel number down  
DVD, VCD, or CD mode: 1) press to skip to the next chapter or track; 2) press and  
hold to search forward; Tuner mode - tunes channel number up  
EX BASS - switches EX BASS to Soft Bass, Balance Bass or Powerful Bass  
SOURCE - switches between AV mode, tuner mode, and DVD mode  
Ventilation  
Note: If the selected language is not recorded on the disc, the disc’s default language is selected automatically.  
6.  
7.  
CAUTION: Do not block any ventilation openings. Install in accordance with these instructions.  
Setting up the volume  
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of your home  
theater and to protect it from over-heating.  
The openings should never be blocked by placing your home theater on a bed, sofa, rug, or other similar surface.  
This home theater should not be placed in a built-in installation such as a bookcase or rack unless correct  
ventilation is provided or these instructions have been adhered to.  
8.  
Basic setup  
1.  
2.  
STANDBY/ON - Press to toggle between Operating and Standby mode.  
0 - 9 (numeric keys): DVD mode - Press to enter title, chapter, track, and time search  
selections. Tuner mode - Press to enter a preset station.  
TITLE - Press to display the title menu if present on the disc.  
Stop - Press to stop playing.  
Laser warning  
WARNING: This home theater uses a laser system.  
NOTE: When in AV1 or AV2 mode, only composite video sources have a video output signal. Connect only the  
RCA video cable to your television set.  
To complete basic setup:  
9.  
To ensure correct use of this home theater, read this user guide carefully and retain it for future reference. Should  
your home theater require maintenance, contact an authorized service center.  
1.  
Press the SETUP / EXIT button to enter the System Setup Menu.  
3.  
4.  
5.  
2 Connect the audio  
10.  
11.  
Changing controls, making adjustments, or carrying out procedures other than those specified herein may  
result in hazardous radiation exposure.  
To set the volume on a speaker:  
1.  
MENU - 1) DVD mode - Press to enter the Disc Contents menu. 2) PBC ON mode  
- Press to view a VCD disc menu.  
Select Volume Setup, then press OK. You will hear the calibrating sound from the  
front left speaker for a few seconds. This sound then move from speaker to speaker  
as follows :  
To prevent direct exposure to the laser beam, do not try to open the enclosure. There is visible laser radiation  
when open.  
12.  
6.  
Active Navigation mode  
-
Press to navigate in the indicated  
Do not stare into the beam.  
directions for making selections in menus  
Tuner Mode - Press or to change the radio frequency  
Press or to change the radio channel  
Front Left  
Subwoofer  
Center  
Rear Right  
Front Right  
Rear Left  
13.  
14.  
Laser Type: Dual semiconductor laser GaAIAs  
Wavelength: 650nm and 780nm  
Output Power: 7mW  
If the calibrating sound is either too soft or too loud, exit Volume Setup, then adjust the  
volume control until the calibrating sound is clearer. Let the calibrating sound cycle through  
all the speakers at least once.  
Back  
7.  
/
- Press to skip backward or forward to the previous or next chapter or  
2.  
3.  
Press or to navigate to one of these menus:  
Beam Divergence: 60 degree  
track  
System Setup  
Audio Setup  
Speaker Setup  
Language Setup  
Video Setup  
CAUTION: Visible and invisible laser radiation is present when your home theater is open and interlocks are  
8.  
9.  
10.  
BOOKMARK - Press to open Bookmark menu  
V-SELECT - Press to switch among the different video outputs.  
ZOOM / CLEAR - 1) Press to select different zooming size while playing a video, 2)  
Press to clear the information you entered in a setup menu.  
ANGLE / PBC - 1) Press to toggle between different angles to view (if present on disc).  
2) Press to turn PBC on or off on a VCD disc.  
TUNER / AUX - Press to select AV 1, AV 2, or tuner mode.  
DVD - Press to select DVD mode.  
SURROUND - Press to select different surround sound effects among STEREO  
If the calibrating sound level from all speakers is approximately the same, no further  
adjustment is necessary.  
If any speaker sound level appears unbalance to the rest, you can increase or decrease  
the level of the speaker by pressing or to increase or decrease the speaker level  
when that speaker is highlighted.  
defeated.  
Power cord  
When any menu is highlighted, press or to select different settings under the  
menu. Available options for each setting appear on the right side of the screen.  
Press or OK to move to the right column.  
Press or to select a new setting, then press OK to confirm the changed setting.  
Repeat steps 3 to 5 to change the other settings.  
Press to return to the previous menu.  
Press to return to the main menu.  
Repeat steps 2 to 8 to change all settings.  
After you have finished making the changes, highlight EXIT SETUP, press OK.  
-OR-  
Press SETUP / EXIT again to exit Setup Menu.  
CAUTION: It is recommended that most appliances be placed on a dedicated circuit— a single outlet circuit  
powering that appliance only and one that has no additional outlets or branch circuits. Check the specification  
section of this guide for power requirements.  
11.  
4.  
5.  
6.  
7.  
8.  
9.  
10.  
2.  
When you have completed the level adjustments, press OK to exit the Volume Setup  
and return to the previous menu.  
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed  
power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in  
electric shock or fire.  
3 Connect the speakers  
12.  
13.  
14.  
NOTE: This DVD home theater system is designed to reproduce optimum sound quality when the supplied  
speakers are used. If you want to connect speakers other than the ones supplied, they should be 6 ohms  
impedance for the speakers and 3 ohms impedance for the subwoofer.  
Note: We recommend to set Volume = 30 before entering this Volume Setup to further calibrating any  
unbalance speaker level output.  
Periodically examine your home theater cord, and if its appearance indicates damage or deterioration, unplug  
it, discontinue use of your home theater, and have the cord replaced with an exact replacement part by an  
authorized service provider.  
Note: Speaker volume can also be changed in AV mode:  
PROLOGIC II MOVIE, PROLOGIC II MUSIC, CONCERT, CHURCH, PASSIVE, WIDE, and  
LIVE.  
Make sure that you use the correct polarity when connecting the speakers (colored wire connects to the  
matched color terminal clip).  
Press TUNER/AUX to select AV1 or AV2 mode. Movies or music on the connected VCR will play through  
this home theater.  
Press SETUP/EXIT once. FL (front left) is displayed on the VFD. Press or  
want to change the volume of: FL (front left), FR (front right), SL (surround left), SR (surround right), CEN  
(center, or SUB (subwoofer).  
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in  
a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits your  
home theater.  
1.  
2.  
Power cord - plug into an electrical outlet  
To prevent damage to circuits, never short-circuit the speaker output terminals.  
NOTE: You can select Surround Sound Effect (DSP) only for STEREO contents (2 channels). You can not select  
DSP while playing back a DVD with multichannel audio content like Dolby Digital 5.1.  
to select the speaker you  
Subwoofer speaker - connect a passive subwoofer, with the colored wire attached  
to the + terminal and the black wire attached to the - terminal FM antenna input  
connections  
Front speaker - connect the left front speaker to the L terminals and right front  
speaker to the R terminals. Connect the colored wire to the + terminal and black  
wire to the - terminal  
Component video and progressive outputs - connect a television that has  
component video input . Use a component video cable.  
Digital coaxial output - connect an external device that has a digital audio input  
jack.  
15.  
SLEEP - Press to activate a sleep timer for your home theater to go into standby mode  
automatically  
To disconnect power from the outlet, pull out the plug. When installing your home theater, make sure that the  
plug is easily accessible.  
Setting details  
Setting up the screen saver  
3.  
16.  
17.  
18.  
19.  
20.  
21.  
22.  
23.  
24.  
25.  
26.  
OPEN/CLOSE - Press to open or close the disc tray  
- VOL + - Press to increase or decrease the volume  
MUTE - Press to mute and unmute the sound output  
INFO - Press to display current information about disc that is playing  
Pause - Press to freeze the picture and stop the sound during playback  
Play - Press to start playing  
IMPORTANT SAFETY INSTRUCTIONS  
CAUTION: Read and observe all warnings and instructions in this user guide and those marked on your home  
4.  
5.  
6.  
theater. Retain this guide for future reference.  
When a speaker has been selected, press  
+10 DB.  
or  
to increase or decrease volume -10 DB to  
This home theater has been designed and manufactured to assure personal safety.  
Improper use can result in electric shock or fire hazard. The safeguards incorporated in this home theater will  
protect you if you observe the following procedures for installation, use, and servicing. This home theater does  
not contain any parts that can be repaired by you.  
Turning on the dynamic range  
SETUP / EXIT - Press to enter or exit the System Setup menu  
OK - Press to enter or select a value in a menu and setup navigation  
FM antenna input connections - FM reception - Connect the FM antenna to the FM  
jack. Move the antenna in various directions until the clearest signal is received.  
To connect the speakers:  
Press the speaker terminal clip down and insert the wire, then release the clip.  
Do not remove the cabinet cover or you may be exposed to dangerous voltage. Refer servicing to qualified  
service personnel only.  
Read all safety and operating instructions before operating your home theater.  
Keep safety, operation, and use instructions for future reference.  
Heed all warnings on your home theater and in the operating instructions.  
All operation and use instructions should be followed.  
Do not use this home theater near water. For example, do not use this home theater near a bath tub,  
wash bowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool, and other areas located  
near water.  
Clean only with dry cloth. Unplug this home theater from the wall outlet before cleaning. Do not use liquid  
cleaners.  
Do not block any ventilation openings. Install in accordance with these instructions. Slots and openings in  
the cabinet are provided for ventilation, to ensure reliable operation of your home theater, and to protect  
it from over-heating.  
Do not block any ventilation openings. Do not place your home theater on a bed, sofa, rug or other similar  
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless correct  
ventilation is provided or these instructions have been adhered to.  
Do not install near any heat sources such as radiators, heat registers, stoves, or other electronic devices  
(including amplifiers) that produce heat.  
/
- Press to search backward or forward  
SUBTITLE - Press to toggle between different subtitles  
AUDIO / FM ST - 1) DVD mode - Press to change to a different audio stream, 2)Tuner  
mode - Press to select Mono or Stereo.  
ROTATE - Press to rotate the picture  
GOTO - Press to start play at a specific location on a DVD, CD, VCD, or SVCD disc  
PLAYMODE - Press to display Playmode Menu to select a different play mode  
A-B - Press to setup repeat playback or to clear repeat playback  
EX BASS - Press to turn EX BASS to Soft Bass, Balance Bass, or Powerful Bass  
TONE - Press to select an EQ modes from FLAT, ROCK, POP, CLASSIC, and JAZZ  
Use this setting to turn the screen saver option on or off. If you turn the screen saver on, the  
screen saver image appears when you leave your home theater in Pause or Stop mode more  
than five minutes. This saver can protect the television screen from being damaged.  
1
2
27.  
28.  
29.  
30.  
31.  
32.  
Setting a password and rating level  
Dynamic Range Control enables you to control the dynamic range to achieve a suitable  
sound for your home theater.  
ON: Loud sounds, such as explosions, are turned down slightly during playback.  
OFF: Your home theater plays at the recording level on the disc.  
AM loop antenna connections - AM reception - Connect the AM loop antenna to  
the AM jack. Position the loop antenna to receive the clearest sound. Fully insert the  
stripped portion of the antenna into the terminal as shown.  
NOTE: Position the antenna as far away as possible from a TV, VCR or other radiation  
source.  
* * * *  
Connect all speakers in the same manner.  
Caution:  
Specifying the type of digital audio  
7.  
8.  
Active subwoofer out - connect an external powered subwoofer using this jack  
Do not remove too much insulation from the wire cables to avoid the stripped  
portions from touching each other. The optimal length for the stripped part should  
be around 1/3 inch (or 1cm).  
Setting up your DVD home theater system  
Surround speaker (rear speakers) - connect the left surround speaker to the SL  
terminals and right surround speaker to the SR terminals. Connect the colored wire  
to the + terminal and the black wire to the - terminal  
Center speaker - Connect the center speaker, with the colored wire attached to the  
+ terminal and the black wire attached to the - terminal.  
Audio inputs - Connect audio (Left and Right) cables from a VCR, TV or satellite  
receiver to play them through this home theater system. These connections are  
labelled AV1 and AV2 and are selected by using the SOURCE button on the front  
panel.  
Video inputs - connect video cables from the corresponding video out jacks on aTV,  
VCR or satellite receiver to play them through this home theater. These connections  
are labelled AV1 and AV2 and are selected by using the SOURCE button on the front  
panel.  
Video output (VCR) - connect a VCR or other recording device to this jack. Most  
DVDs cannot be recorded, however you can use this connection to record from the  
auxiliary inputs such recording from the satellite receiver.  
Audio outputs (VCR) - connect audio (Left and Right) cables to external recording  
devices such as a VCR or cassette recorder  
S - Video output - Connect to the S-VIDEO IN jack on the television using an S-Video  
cable. This type of connection provides superior picture quality.  
NOTE: Your television must be equipped with an S-Video input jack.  
Unpacking your DVD Home Theatre System  
Many DVD movie discs contain Motion Picture Association rating codes. This home theater  
system recognizes the codes on these DVDs.Your home theater provides a method for you to  
prevent children from viewing films which you deem are not suitable or find objectionable.  
1.  
2.  
3.  
4.  
Do not push the stripped part too far into the speaker connectors.  
Your box includes the following:  
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The  
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,  
consult an electrician for replacement of the obsolete outlet.  
Protect the power cord from being walked on or pinched particularly at plugs, receptacles, and the point  
where they exit from your home theater.  
9.  
One DVD Home Theatre System  
This user guide  
One AV Cable  
Two rear speakers  
One subwoofer  
One remote control with two batteries  
Quick installation guide  
AM and FM Antennas  
Two front speakers  
One center speaker  
Positioning the speakers  
KID SAFE: Content is safe for children.  
G: Recommended as acceptable for all ages.  
PG: Parental Guidance is suggested.  
10.  
Center Speaker  
Subwoofer  
Front  
Front  
speaker  
speaker  
(
right  
)
(
left  
)
TV  
Choose the type of digital audio output that matches the audio connection between your  
home theater and the external digital audio decoder.  
SPDIF/RAW: Outputs the audio stream in original undecoded format.  
SPDIF/PCM: Outputs the audio stream in decoded PCM format.  
Use only attachments or accessories specified by Insignia.  
PG-13: Material may not be suitable for children under age 13.  
Use only with the cart, stand, tripod, bracket, or table specified by Insignia, or sold  
with this home theater system. Use caution when moving the cart/home theater  
combination via cart to avoid injury from tip-over.  
Unplug this home theater during lightning storms or when unused for long periods  
of time.  
Refer all servicing to qualified service personnel. Servicing is required when your home theater has been  
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects  
have fallen into your unit, your home theater has been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
When replacement parts are required, be sure the service technician uses replacement parts specified by  
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may  
result in fire, electric shock, or other hazards.  
11.  
12.  
5-6. R: Parents should restrict children under 17 from viewing this material or let them  
Connecting your DVD Home Theater System  
DIM  
C
view the material only when superivised by a parent or adult guardian.  
DIM  
L
DIM  
R
The following setup and installation illustrations show various video and audio connections  
to TV and VCR.  
7.  
8.  
NC-17: Not recommended viewing for children under age 17.  
Adult: Should be viewed only by adults due to graphic sexual material, violence, or  
language.  
Modifying the Prologic II setting  
Rear speaker  
left surround  
Rear speaker  
right surround  
(
)
(
)
CAUTION: Make sure that the AC Voltage matches your local voltage. Connect the AC cord only after the  
speakers, antennas, and all optional equipment have been connected.  
DIM LS  
DIM RS  
To set the rating:  
1.  
2.  
3.  
4.  
In the System Setup menu, press or to highlight Rating, then press  
.
13.  
14.  
Where you place the speakers plays an important role in the reproduction of surround sound  
effect.  
Pay particular attention when designing the speaker layout. For the best surround effects, all  
speakers should be installed.  
A typical room layout has the left, center, and right speakers placed across the front and the  
left surround and right surround speakers placed along the sides towards the rear as shown  
in the above left picture. Position the center speaker above or below the video screen or TV.  
Install a subwoofer can be (for powerful bass sounds) anywhere in the room.  
Press or to highlight a rating level, then press OK.  
Press or to highlight Password, then press OK.  
Use the numeric keys (0-9) to enter a four-digit password. If you make a mistake  
before pressing OK, press CLEAR.  
Enter your four-digit security code again.  
Upon completion of any service or repairs to this home theater, ask the service technician  
to perform safety checks to determine that your home theater is in proper operation  
condition.  
USA and Canada versions comply with ETL requirements.  
The Dolby Pro Logic II Surround System is a specially encoded two channel analog format  
which reproduces five channel output when a Dolby Pro Logic II Decoder is used.  
MOVIE MODE: Movie mode is for use with stereo television shows and all programs encoded  
in Dolby Surround. The result is enhanced soundfield directionality that approaches the  
quality of discrete.  
5.  
This product incorporates copyright protection technology that is protected by method  
claims of certain U.S. patents and other intellectual property rights owned by Macrovision  
Corporation and other rights owners. Use of this copyright protection technology must be  
DVD discs that are rated above the level you selected will not play unless you enter correct  
the four-digit password.  
 

Ingersoll Rand Impact Driver W040 User Manual
JVC Car Stereo System 1208MNMMDWJEIN User Manual
JVC CD Player GET0425 001A User Manual
JVC CD Player KD G631 User Manual
JVC DVR 0503 AH ID JVE User Manual
JVC Stereo Receiver RX 6000VBK User Manual
KitchenAid Microwave Oven KBMS1454RBL0 User Manual
Klipsch Speaker RW 5802 User Manual
Kodak Film Camera 2100 Auto User Manual
Kramer Electronics Stereo Receiver PT201VGA User Manual