Installation Guide
For SF12Mi and SF15i Models Only
Part Number: 351940-001
Working Load Limit
The JBL SoundFactor Install loudspeakers are supplied with built-in internal braces to be used with the
supplied forged shoulder eyebolts or other approved fastener.The system is designed to facilitate the sus-
pension of the loudspeaker by a qualified person familiar with rigging hardware and industry practices.
IMPORTANT! You must ensure that ALL installation procedures specified in this manual
are carefully followed. Improper installation may result in damage, injury or death.
The working load limit (WLL) of any JBL SoundFactor Install loudspeaker is maintained as long as no
more than one loudspeaker is suspended by a minimum of two primary suspension points with no addi-
tional load placed on the loudspeaker enclosure. The JBL SoundFactor Install loudspeakers are intend-
ed for SINGLE-BOX SUSPENSION ONLY. DO NOT HANG A SECOND SPEAKER FROM A SOUND-
FACTOR INSTALL SPEAKER.
Secondary
Load
Secondary
Load
Primary
Load
Primary
Load
Primary
Load
Primary
Load
SF15i
Secondary
Load
SF12Mi
3
General Hardware Information
Any hardware used in an overhead suspension application must be load rated for the intended use.
Generally, this type of hardware is available from rigging supply houses; industrial supply catalogs and
specialized rigging distributors. Local hardware stores do not usually stock these products. Hardware that
is intended for overhead suspension will comply with ASME B30.20 and will be manufactured under prod-
uct traceability controls. Compliant hardware will be referenced with a working load limit (WLL) and a
traceability code.
All SoundFactor Install loudspeakers include a rigging hardware kit (part# 229-00009-01) which includes
3 forged shoulder eyebolts and 3 washers. When installing these speakers, use hardware found in the kit
provided. For additional rigging components, consult with a professional rigging hardware supplier.
Sources for specialized rigging hardware may be found on page 11.
Proper Use of Forged Shoulder Eyebolt
The JBL SoundFactor Install loudspeakers are supplied with three forged M10-1.5 x 35 mm shoulder eye-
bolts with appropriate ratings and certified standards compliance, for use in overhead suspension appli-
cations. To install the eyebolts into the provided threaded holes on the loudspeaker, first remove the fac-
tory installed, flat head machine screw using a 6 mm hex key wrench. The M10-1.5 threaded internal
brace is accessible once the flat head machine screw is removed. Deposit thread lock adhesive, follow-
ing the adhesive manufacturer's instructions, onto the threaded tip of the eyebolt. Install the forged shoul-
der eyebolt as a replacement for the machine screw, being careful not to cross-thread the fasteners.There
should be little resistance when installing any fastener. As a general rule for "soft surface" installations
such as a wooden surface, the suggested torque is achieved by installing the fastener until snug and then
rotating the fastener an additional 180 degrees (1/2 turn).
The load imposed on the eye of the eyebolt fastener must remain in the plane of the eye only. When any-
thing other than a straight-line pull is used, the provided forged, shoulder eyebolt load rating must be
adjusted as follows:
Direction of Pull
Adjusted Working Load
45 degrees
25% of rated working load
In-Line
45º
Do Not
Load
90º
4
Proper Sling Termination
The slings described herein are "suspension slings" and are different from "lifting slings" as defined by
government regulatory bodies. Do NOT use hardware chain. The JBL SoundFactor Install loudspeakers
must be used in static suspension applications only. Wire rope suspension slings are suggested for all
installations requiring suspension of the JBL SoundFactor Install loudspeakers. The suggested wire rope
is identified as 1/8" 7 x 19 Galvanized Aircraft Cable (1/8- 7 x 19 GAC). The minimum working load limit
(WLL) of this type of wire rope is 400 lb / 181 kg when terminated properly. If sling lengths are pre-deter-
mined and the wire rope slings are fabricated at a rigging supplier, the suggested termination is identified
as "swaged Flemish eye terminations with heavy thimbles and certification tags." If sling lengths cannot
be predetermined and slings must be fabricated on site, the suggested termination is identified as either
a load rated "compression sleeve" or a forged "wire rope clip". Compression sleeves, such as the
Nicopress devices, require a specialized compression tool and associated check gauge. Wire rope clips
require an end-wrench, socket wrench, and/or adjustable wrench (spanner). The following table defines
the load rating adjustments associated with each termination type if the terminations are made accord-
ing to manufacturer's instructions:
Termination Type
Swagged Flemish Eye
Adjusted Working Load
100% of wire rope rating
100% of wire rope rating
80% of wire rope rating
Load Rated Compression Sleeve
Forged Wire Rope Clip
Live
End
Nicopress Oval Sleeve
Dead
End
Finished Eye Splice
Saddle
U-Bolt
5
Rigging Connections
Some installations require the use of a removable connection between the structure and the loudspeak-
er. Hardware commonly used for these applications includes:
Quick Link
Screw Pin Anchor Shackle
Used in-line or at an angle up to
45 degrees and can combine two
wire ropes into one. A mouse wire
(aka safety wire) must be used
after installation.
Used in-line with only one wire
rope per end. Only use load rated
quick links, which will have the
WLL imprinted on the component.
Some installations require the adjustment of the length of one or more slings. Common hardware used
for these applications include:
Turnbuckle
Used in-line with only one wire rope per end
and can be adjusted to length. A mouse wire
must be used after adjustment is complete.
Note: Use only turnbuckles with closed,
forged eyes.
6
Attachment to Structures
A licensed Professional Engineer must approve the placement and method of attachment to the
structure prior to the installation of any overhead object. The following performance standards
should be provided to the Professional Engineer for design purposes; Uniform Building Code as applica-
ble, Municipal Building Code as applicable, Seismic Code as applicable, and a minimum of a 5:1 design
factor throughout the suspension system.
The installation of the hardware and method of attachment must be carried out in the manner specified
by the Professional Engineer. Improper installation may result in damage, injury or death.
The following renderings represent some of the common methods of attaching to a structure. These ren-
derings are intended as a reference only, and are not appropriate for many installation circumstances. In
the following illustrations, the structure component is shown in solid black while the attachment hardware
is drawn as an outline.
H-Beam
I-Beam
Beam Clamp
hardware as provided
H-Beam Clamp (custom)
hardware as provided
Channel Beam
Box Beam
Channel Beam Clamp (custom)
hardware as provided
H-Beam Clamp (custom)
hardware as provided
7
Attachment to Structures
Angle Beam
Wood Beam
OSR Fitting
grade 8 or B7 fasteners
Angle Beam Clamp (custom)
hardware as provided
Concrete Beam
Round Beam
OSR Fitting
concrete anchors
Wire Rope Sling (standard)
sling and SPA shackle
Brick Wall
Metal Stud
Mounting Plate (standard/custom)
concrete anchors with epoxy
Mounting Plate (standard/custom)
grade 8 or B7 fasteners
8
Specifications - SF12Mi
SF12Mi
System Type:
Frequency Range (-10 dB):²
12" 2-way, stage monitor
60 Hz - 16 kHz
Frequency Response (±3 dB):² 70 Hz - 12 kHz
Sensitivity (1w/1m):
Nominal Impedance:
Power Capacity:¹
98 dB SPL
8 Ω
250 watts
Peak Power Capacity:¹
Maximum SPL:
1000 watts
129 dB
Nominal Dispersion:
Crossover Frequency:
Dimensions (H x W x D):
90° x 50°
1.8 kHz
584.2 mm x 393.7 mm x 317.5 mm
(23 in x 15.5 in x 12.6 in)
Weight:
19.5 kg (43 lbs.)
Shipping Weight:
22.0 kg (48.5 lbs.)
High Frequency Driver:
Low Frequency Driver:
Input Connectors:
Enclosure Construction:
JBL 2412 1" exit compression driver mounted on Progressive Transition™ Waveguide
JBL M112-8
Neutrik® Speakon® NL-4 (x1); 1/4" TS phone jack (x1); parallel
19 mm (3/4 in) MDF (Medium Density Fiberboard); with glued and mechanically fastened joint
detail; covered in black carpet.
Grille:
18 gauge, powder-coated steel
Suspension:
Suspension Kit:
3x M10 threaded suspension points
3x 10 mm forged shoulder eyebolts with washers
Notes:
1. "Power Capacity" and "Peak Power Capacity" ratings are based on the average and peak power handling capacity of product
samples subjected to a 100 hour power test of the system design using IEC filtered random noise with a crest factor of 6 dB.
2. "Frequency Range" and "Frequency Response" are based on half-space response.
+
HPF
-
TIP GRD
1+
1-
IN
(PARALLEL JACKS)
OHMS
/
OUT
+
-
8
LPF
1
2
FULL-RANGE
N/C
MODEL SF12
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
9
Specifications - SF15i
SF15i
System Type:
Frequency Range (-10 dB):²
15" 2-way, sound-reinforcement speaker
38 Hz - 16 kHz
Frequency Response (±3 dB):² 50 Hz - 12.5 kHz
Sensitivity (1w/1m):
Nominal Impedance:
Power Capacity:¹
98 dB SPL
8 Ω
250 watts
Peak Power Capacity:¹
Maximum SPL:
1000 watts
128 dB
Nominal Dispersion:
Crossover Frequency:
Dimensions (H x W x D):
90° x 50°
1.6 kHz
698.5 mm x 459.9 mm x 431.8 mm
(27.5 in x 18.11 in x 17 in)
Weight:
27.4 kg (60.5 lbs.)
Shipping Weight:
30.4 kg (67.0 lbs.)
High Frequency Driver:
Low Frequency Driver:
Input Connectors:
Enclosure Construction:
JBL 2412, 1" exit compression driver mounted on Progressive Transition™ Waveguide
JBL M115-8A
Parallel Neutrik® Speakon® NL-4 (x1); 1/4" TS phone jack (x1)
19 mm (3/4 in) MDF (Medium Density Fiberboard); with glued and mechanically fastened joint
detail; covered in black carpet.
Grille:
18 gauge, powder-coated steel
Suspension:
Suspension Kit:
3x M10 threaded suspension points
3x 10 mm forged shoulder eyebolts with washer
Notes:
1. "Power Capacity" and "Peak Power Capacity" ratings are based on the average and peak power handling capacity of product sam-
ples subjected to a 100 hour power test of the system design using IEC filtered random noise with a crest factor of 6 dB.
2. "Frequency Range" and "Frequency Response" are based on half-space response.
+
HPF
-
TIP GRD
1+
1-
IN
(PARALLEL JACKS)
OHMS
/
OUT
+
-
8
LPF
1
2
FULL-RANGE
N/C
MODEL SF15
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
10
Product Dimensions
SF12Mi
7.8 in
198 mm
60º
12.7 in
323 mm
8.4 in
213 mm
3.9 in
99 mm
2x O .45 in
11.4 mm
12 in
305 mm
O .45 in
11.4 mm
1.8 in
45.7 mm
15.5 in
394 mm
12.7 in
323 mm
22.7 in
577 mm
15.5 in
394 mm
8.4 in
213 mm
SF15i
13.8 in
351 mm
2x 2.4 in
60.9 mm
17 in
432 mm
8.0 in
203 mm
2x O .45 in
11.4 mm
2x 1.75 in
44.5 mm
2x 82.5º
18.5 in
470 mm
17 in
432 mm
5.4 in
137 mm
27.2 in
691 mm
3.8 in
96.5 mm
8.9 in
226 mm
3.5 in
88.9 mm
O .45 in
11.4 mm
9.25 in
235 mm
11
Inspection, Maintenance and Liability
Suspension systems are comprised of mechanical devices and, as such, they require regular inspection and routine main-
tenance to ensure that safety has not been compromised. The JBL SoundFactor Install loudspeakers and associated sus-
pension components must be inspected for fatigue at least annually and immediately following exposure to impact,
mechanical shock, fire, water or other hazard. The inspection must include a visual survey of all corners and load bearing
surfaces for signs of cracking, water damage, de-lamination, and any other condition that may decrease the strength of
the loudspeaker enclosure or associated suspension components. The forged shoulder eyebolts provided with the JBL
SoundFactor Install loudspeakers must be inspected for fatigue at least annually. The inspection must include a visual sur-
vey of the material for signs of corrosion, bending or any other condition that may decrease the strength of the fastener.
Additionally, the eyebolts must be checked for possible spin-out of the enclosure. For all other hardware and fittings, refer
to the hardware manufacturer's inspection and maintenance guidelines for process. Should any signs of unsafe conditions
be observed, repair or replacement of the deteriorated component(s) must be completed before anyone other than some-
one performing the repair is allowed access to the vicinity of the unsafe condition.
Note:
The working load limit (WLL) of the JBL SoundFactor Install loudspeakers includes; a design factor equivalent to or
exceeding ASME B30.20, VBG70, VBG9a and the manufacturer's proprietary performance standard.
All implied warranties, including warranties of merchantability and fitness for particular purpose, are limited in duration to
the length of the warranty. JBL's liability shall in no event exceed the cost of any defective product and shall not include
incidental or consequential damages of any kind, even if JBL has been advised of the possibility. Some states do not allow
limitations on how long certain warranties last and/or do not allow exclusion of incidental or consequential damages, so
the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
JBL is not responsible for the application of its products for any purpose or the misuse of this information for any purpose.
Furthermore, JBL is not responsible for the abuse of its products caused by avoiding compliance with inspection and main-
tenance procedures or any other abuse.
Resources
Allen Products
ATM Fly-Ware
(562) 424-1100
(888) RIG-MORE / (310) 834-5914
2100 South Wilmington Avenue
Carson, CA 90810
1635 E. Burnett Street
Signal Hill, CA 90806
M.A.N. Flying Systems
20 Sidar Road
Brook Road Industrial estate
Rayleigh, Essex SS6 7XF
McMaster Carr
Various locations through the United States.
For a location near you, visit them online at
JBL Professional - Tech Note V1 No. 14
“Basic Principles For Suspending Loudspeakers”
JBL Professional Contacts
Mailing Address:
JBL Professional
Shipping Address:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329
8370 Balboa Blvd., Dock D
Northridge, CA 91329
Customer Service:
Monday through Friday
8:00am - 5:00pm
On the World Wide Web:
pacific coast time in the U.S.A.
(800) 8JBLPRO (800.852.5776)
Product Registration:
Register your product online at
© Copyright 2003 JBL Professional
|