JBL Speaker IBT User Manual

jbl On TOuribT  
Bluetooth® Portable Loudspeaker  
Owner’s Manual  
®
 
jbl On TOurIbT  
fcc statement and WarninG  
FCC InFormatIon For Users  
IntroductIon  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference; and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
With no wires to tangle or restrict your movement, and controls  
conveniently located on the unit, the JBL On TouriBT loudspeaker  
is both the ultimate in portable audio convenience and a paragon of  
superior audio quality.  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause interference to  
radio or television reception, which can be determined by turning the equipment off and then on,  
the user is encouraged to try to correct the interference by one or more of the following measures:  
A compact, high-performance Bluetooth® sound center, when paired  
with your iPad or other Bluetooth A2DP-enabled audio device,  
Bluetooth music phone, iPhone, iPod, MP3 player or any other music  
source with an audio jack, the JBL On Tour iBT loudspeaker will provide  
clean, powerful sound in a compact, portable design. Accept a phone  
call with the included Bluetooth speakerphone feature. Take complete  
control of your traveling experience with the JBL On Tour iBT portable  
loudspeaker.  
• Reorient the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
compatIbIlIty  
Any changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment. Industry Canada Statement: This Class  
B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
The JBL On Tour iBT system is compatible with most Bluetooth-  
enabled devices, music players, cell phones and laptops. Enabled with  
Bluetooth A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/  
Video Remote Control Profile) and HFP (Hands-Free Profile), the system  
can stream high-quality sound and serve as a speakerphone. With  
the included Apple cable and additional stereo mini jack connection,  
you can enjoy high-quality audio via direct connection with a variety  
of devices such as iPad, iPhone, iPod, MP3 and CD players, desktop  
computers (all platforms), laptops and satellite radio tuners.  
tabletop Stand  
Use the included tabletop stand to support your iPad or other  
Bluetooth-enabled tablet while you’re streaming to the JBL On Tour iBT.  
When you’re ready to go, snap the stand right to the JBL On Tour iBT  
unit for easy and convenient transport.  
www.jbl.com  
3
 
compact deSIgn  
General seTup  
The JBL On Tour iBT portable loudspeaker is a complete two-channel  
audio system in one easy-to-place footprint. The JBL On Tour iBT  
loudspeaker delivers sound with a powerfully tuned digital audio  
path. Its clean and compact digital amplification, coupled with DSP  
(digital signal processing) equalization, efficiently provides the four JBL  
Odyssey® transducers with cool-running power.  
Unpack the JBL On Tour iBT system and its power supply.  
1. Snap the outlet adapter onto the power supply, plug the power  
supply into the “12V DC In” port on the back of the unit and then into  
a wall outlet.  
2. Turn on the power switch. The Power LED will glow green.  
advanced technology  
The JBL On Tour iBT system combines many proprietary technologies  
to provide the highest-quality sound. It provides astonishing bass and  
clear, accurate sound from any direction. The four JBL Odyssey full-  
range transducers are driven by powerful neodymium magnets, and  
provide accurate sound at all frequencies.  
3. To set up the tabletop stand, pull up the center panels as shown  
in the illustration and place the tablet player on it. (You can set the  
stand in one of three positions.)  
1.  
2.  
computer-optImIzed equalIzatIon and compreSSIon  
The JBL On Tour iBT system equalization is computer-optimized  
to provide a rich, complete soundstage. Proproetary compression  
topology ensures clean, accurate sound at high output levels.  
Power Switch  
unpackInG  
Carefully unpack your speaker system and identify all its components:  
3.  
Apple cable  
Power supply and  
outlet adapter*  
JBL On Tour iBT unit  
Tabletop stand for  
tablet media players  
*Outlet adapter varies by region.  
4
 
VOluMe cOnTrOls  
baTTery dIspOsal  
Volume increase “+”  
Volume decrease “–”  
Alkaline batteries are considered nonhazardous. Rechargeable batteries  
(i.e., nickel cadmium, nickel metal-hydride, lithium and lithiumion)  
are considered hazardous household materials and may pose an  
unnecessary health and safety risk.  
Phone button “  
Microphone “  
In the European Union and other locations, it is illegal to dispose of any  
battery with household trash. All batteries must be disposed of in an  
environmentally sound manner. Contact your local waste management  
offcials for information regarding the environmentally sound collection,  
recycling and disposal of used batteries.  
baTTery InsTallaTIOn  
1. Rotate the battery compartment cover on the bottom of the JBL  
On Tour iBT speaker to the unlocked position; remove the battery  
compartment cover.  
Bluetooth paIrInG  
2. Place (4) fresh AA batteries as shown.  
3. Replace the battery compartment cover.  
Before you can use your JBL On Tour iBT system with a Bluetooth-  
enabled device, you must pair it with that device.  
To pair the JBL On Tour iBT with your device:  
note: The JBL On Tour iBT will not use battery power when using AC  
power.  
1. Make sure your JBL On Tour iBT system is turned on. The JBL On  
Tour iBT unit automatically goes into Pairing/Discoverable mode,  
represented by the Source LED flashing blue.  
1.  
2.  
3.  
2. Put your Bluetooth-enabled device in Pairing mode so both devices can  
“see” each other. (Refer to the Bluetooth-enabled devices users guide  
for directions and details about putting it into Pairing mode.) The JBL On  
Tour iBT unit will be represented as “JBL On Tour iBT” on your Bluetooth-  
enabled device. The JBL On Tour iBT password is 0000.  
3.The JBL On Tour iBT system is successfully paired and ready to use  
when the Source LED glows a constant blue.  
DO NOT MIX BATTERY TYPES.  
DO NOT MIX CHARGED AND PARTIALLY CHARGED BATTERIES.  
BATTERIES WILL NOT RECHARGE WHILE IN THE UNIT.  
note: Bluetooth pairing between two devices does not have to be repeated  
after a successful initial pairing, unless the JBL On Tour iBT system has been  
removed from the Bluetooth-enabled devices Bluetooth device list.  
cautIon: Risk of explosion if battery is incorrectly replaced.  
Replace only with the same or equivalent type.  
www.jbl.com  
5
 
• To mute a phone call: Press both Volume buttons on the JBL On  
Tour iBT system. To unmute the phone call: Press either Volume  
button on the JBL On Tour iBT unit.  
lIsTenInG TO a phOne call frOM a  
Bluetooth-enabled deVIce  
1. Make sure the JBL On Tour iBT speaker is paired (see Bluetooth  
Pairing section, on page 5).  
2. When you hear your Bluetooth-enabled devices ringtone from the  
JBL On Tour iBT system, press the Phone “ ” button to answer the  
phone call.  
Or  
3. When the phone call is finished, press the Phone “ ” button to end  
the phone call.  
MakInG a phOne call frOM a Bluetooth-  
enabled deVIce  
To make a phone call via voice recognition mode, press and hold the  
Phone “ ” button for two seconds.  
note: If the phone does not support voice recognition this action will  
redial the last number that was called on the phone.  
• To reject an incoming phone call: Press and hold the Phone “  
button on the JBL On Tour iBT unit for two seconds.  
• To answer a second incoming phone call while putting the first call  
on hold: Press the Phone “ ” button.  
• To reject a second incoming phone call while staying on the first call:  
Press and hold the Phone “ ” button for two seconds.  
6
 
4. Use the Bluetooth-enabled device to control playback. Adjust the  
volume using the “+” and “–” buttons located on the front of the  
JBL On Tour iBT unit.  
lIsTenInG TO MusIc  
There are three ways to listen to music on your JBL On Tour iBT:  
LISTENING TO MUSIC FROM A CONNECTED iPad, iPhone or iPod  
DEVICE  
• Via Bluetooth technology from a Bluetooth-enabled device.  
• Using the supplied Apple cable to connect an iPad, iPhone or iPod  
device to the JBL On Tour iBTs USB port.  
1. Plug the supplied Apple cable into the JBL On Tour iBT’s USB port,  
and plug your iPad, iPhone or iPod device to the cable’s 30-pin  
connector.  
• Using a stereo 3.5mm audio cable (not supplied) to connect an  
audio devices audio or headphone output to the JBL On Tour iBTs  
auxiliary 3.5mm mini jack.  
To cycle through the sources, make sure the JBL On Tour iBT is not in  
the Bluetooth call mode and momentarily press the Phone “ ” button.  
Each press of the button changes to the next source. The source LED  
will change color to indicate the active source:  
White = Apple cable (USB port)  
Blue = Bluetooth (wireless)  
Green = Auxiliary 3.5mm mini jack  
LISTENING TO MUSIC FROM A BLUETOOTH-ENABLED DEVICE  
1. Make sure the JBL On Tour iBT system is paired with your  
Bluetooth-enabled device (see Bluetooth Pairing section, on page 5).  
2. Press the JBL On Tour iBT’s Phone “ ” button until the Source LED  
lights white constantly. This indicates that the Apple cable (USB)  
input is selected.  
2. Press the JBL On Tour iBT’s Phone “ ” button until the Source  
LED lights blue constantly. This indicates that the Bluetooth input is  
selected.  
3. Use the iPad, iPhone or iPod device to control playback. Adjust the  
volume using the “+” and “–” buttons located on the front of the  
JBL On Tour iBT unit.  
3. Go to the Bluetooth-enabled device’s music player and play music.  
Refer to the Bluetooth-enabled device’s user’s guide for directions  
and details about using its music player and transmitting music via  
Bluetooth technology.  
NOTE: When the JBL On Tour iBT is running on AC power, it will  
recharge the iPad, iPhone or iPod device while it is connected.  
www.jbl.com  
7
 
LISTENING TO MUSIC FROM A CONNECTED AUXILIARY DEVICE  
charGInG  
1. Connect the auxiliary device to the JBL On Tour iBT system using a  
3.5mm stereo audio cable (not supplied).  
When the JBL On Tour iBT is running on AC power, the units USB port  
will charge most mobile phones and portable music players. An Apple  
cable is supplied for charging Apple iPhone, iPod and iPad devices. For  
other types of devices, use the charging cable that was supplied with  
your device. If one was not provided, contact the devices manufacturer  
or an authorized dealer to obtain one. note: Mobile phones and  
portable music players that require data communication in order to  
charge will not charge from the JBL On Tour iBT unit.  
Charge Port  
2. Press the JBL On Tour iBTs Phone “ ” button repeatedly until the  
Source LED lights Amber. This indicates that the Aux input source is  
selected.  
carryInG/sTOrInG The TableTOp sTand  
You can easily snap the tabletop stand on and off the JBL On Tour iBT  
for convenient storage or transport.  
3. Control music playback through the auxiliary device. Adjust the  
volume using the “+” and “–” buttons located on the front of the  
JBL On Tour iBT unit.  
8
 
pOwer and sOurce leds  
specIfIcaTIOns  
The Power and Source LED colors change to indicate the state of  
JBL On Tour iBT unit.  
Transducers  
4 x JBL Odyssey  
2 x 8 watts at 1% THD  
100Hz – 20kHz  
>85dB  
Amplifier  
Frequency response  
Signal-to-noise ratio  
Input impedance  
>10k ohms  
Battery size/type  
AA /alkaline, NiMH  
30 watts  
Maximum power consumption  
Power requirement (USA/Canada)  
Source LED  
Power LED  
120 volts, 60Hz AC  
led  
sTaTe  
IndIcaTIOn  
220 – 230 volts,  
50Hz or 60Hz AC  
Power requirement (Europe/UK)  
power led  
Green, constant  
JBL On Tour iBT is on, powered  
by good batteries or its AC power  
supply.  
Power requirement (Japan)  
Power requirement (Australia)  
100 volts, 50Hz or 60Hz AC  
240 volts, 50Hz or 60Hz AC  
Amber, constant  
Batteries are low.  
6-1/2" x 1-5/8"  
(165mm x 41mm)  
Dimensions (Diameter x H)  
Weight  
Source led White, constant  
Apple cable (USB) is the active  
source.  
0.6kg (1.3 lb)  
Blue, constant  
Bluetooth source is paired and is  
the active source.  
Features, specifications and appearance are subject to change without notice.  
Blue, flashing  
JBL On Tour iBT is in Bluetooth  
pairing mode.  
Green, constant  
Aux input connector is the active  
source.  
www.jbl.com  
9
 
TrOubleshOOTInG sOund QualITy  
syMpTOM  
pOssIble prObleM  
sOluTIOn  
nOTe  
There is no sound from your JBL On Tour  
iBT speaker.  
There is no power to the unit.  
Make sure the wall power outlet or power  
strip has power; make sure all switches for the If the Power LED is not on, power  
outlet/power strip are on and that all switches is not getting to your JBL On Tour  
Is the Power LED glowing green?  
for the speaker system are on.  
iBT system.  
Try the solutions shown.  
Make sure that the batteries are properly  
installed, and that they are fresh.  
Ensure that the auxiliary cable is properly  
connected to an external audio device.  
The source selection is incorrect.  
Check that the Source LED is lighted the  
proper color. See Power and Source LEDs,  
on page 9.  
Turn up the volume.  
Check the system with a known good source.  
Connect the Aux In cable to the headphone  
jack on your audio device.  
The source device is not capable of sending  
music via Bluetooth technology.  
Replace the source device with a Bluetooth  
wireless technology-enabled source device.  
Sound comes from only one side/channel.  
The audio cable is not seated properly.  
Make sure the Aux In cable is seated all the  
way into the JBL On Tour iBT system.  
Make sure the audio cable is a stereo cable.  
(A mono cable will only output sound through  
one channel.)  
10  
 
TrOubleshOOTInG sOund QualITy (cOnTInued)  
syMpTOM  
pOssIble prObleM  
sOluTIOn  
nOTe  
There is distortion (static, crackling or  
hissing sounds).  
The noise may be caused by interference  
from a monitor, cell phone or other  
transmitting device.  
Turn the monitor or other device off to see if  
the noise is eliminated.  
Move the JBL On Tour iBT cables farther  
away from the monitor or other device.  
There is too much bass or treble.  
The JBL On Tour iBT system is being  
overdriven by an amplified audio source.  
Ensure that the JBL On Tour iBT system is  
connected to an appropriate source device.  
Make sure that all signal cables are inserted  
snugly into their connectors.  
The volume level may be too high.  
Check the volume of the source device. Some  
devices will distort the output signal if the  
volume is set to maximum.  
Check the EQ setting on your source device. We recommend that the source device EQ be  
set to Flat or Off.  
Your JBL On Tour iBT speaker emits a loud The Aux In cable is not plugged in properly.  
hum or buzzing noise.  
Check the Aux In cable connection  
The speaker experiences radio frequency  
interference or picks up a radio station.  
The input cable may be picking up  
interference.  
Wrap up excess input cable in order to make  
it as short as possible.  
Ensure that the source device has the latest  
software.  
Some source devices have known  
functional issues with the JBL On  
Tour iBT system.  
When streaming music using Bluetooth  
technology, the sound from the JBL On Tour between the JBL On Tour iBT unit and the  
iBT speaker lacks stereo quality. source device.  
There is a Bluetooth compatibility issue  
Turn both the JBL On Tour iBT unit and the  
source device both off and on to reset them.  
www.jbl.com  
11  
 
TrOubleshOOTInG charGInG  
syMpTOM  
pOssIble prObleM  
sOluTIOn  
nOTe  
Your iPod device or cell phone will not  
charge.  
The wrong adapter is being used.  
Make sure the correct adapter is being used  
for your specific iPod or cell phone model.  
Some cell phones cannot charge  
via USB without software from the  
charging system.  
TrOubleshOOTInG paIrInG  
syMpTOM  
pOssIble prObleM  
sOluTIOn  
nOTe  
The audio device does not pair with the JBL The audio device is not compatible with  
Verify compatibility with the manufacturer.  
On Tour iBT system.  
the JBL On Tour iBT system.  
The JBL On Tour iBT system is not  
powered on.  
Press the Power button on the JBL On Tour  
iBT unit.  
The blue LED should be flashing,  
indicating that the system is in the  
Discoverable mode.  
The JBL On Tour iBT system is still paired Disconnect the transceiver from the iPod and  
to the Bluetooth transceiver.  
turn the JBL On Tour iBT system power off,  
then back on.  
The iPod battery is low.  
Charge the JBL On Tour iBT system by  
following the battery charging directions in  
this Owners Manual.  
If the amber LED on the JBL On Tour  
iBT unit is on, it is indicating a low  
battery.  
12  
 
HARMAN Consumer, Inc.  
8500 Balboa Boulevard, Northridge, CA 91329 USA  
© 2011 HARMAN International Industries, Incorporated. All rights reserved.  
JBL and Odyssey are trademarks of HARMAN International Industries, Incorporated, registered in  
the United States and/or other countries. JBL On Tour is a trademark of HARMAN International  
Industries, Incorporated.  
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.,  
and any use of such marks by HARMAN International Industries, Incorporated, is under license.  
iPhone, iPod and iPad are trademarks of Apple, Inc., registered in the U.S. and other countries.  
“Made for iPod,” “Made for iPhone” and “Made for iPad” mean that an electronic accessory  
has been designed to connect specifically to iPod, iPhone and iPad, respectively, and has been  
certified by the developer to meet Apple performance standards. Apple is not responsible for the  
operation of this device or its compliance with safety and regulatory standards. iPod/iPhone/iPad  
not included.  
Features, specifications and appearance are subject to change without notice.  
Part No. 950-0351-001  
www.jbl.com  
13  
 

Indesit Washer Dryer WIA101UK User Manual
Inter Tel Telephone Axxess User Manual
Invacare Mobility Aid IH6065 User Manual
JBL Portable Speaker SCS5005 User Manual
JVC Stereo System CA MXJ850R User Manual
JVC VCR HR J239EE User Manual
Kenwood CD Player KDC X979 User Manual
KitchenAid Ventilation Hood KWCU205HBT User Manual
Kompernass DVD Player KH 6517 User Manual
Konica Minolta Digital Camera Q M200 User Manual