owner’s manual
320W 4-Channel, Full-Range Amplifier
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call our Technical Support Department
at (954) 443-1100 during business hours.
ProteCt Your Hearing!
installation aPPliCations
Planning Your installation
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
This amplifier is designed for operation in
vehicles with 12 volt, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Mounting the amplifier upside down is
strongly discouraged.
If mounting the amplifier under a seat,
make sure there is at least 1 inch (2.5 cm) of
space above the amplifier’s outer shell to permit
proper cooling.
Cooling efficiency Considerations:
The outer shell of your JL Audio amplifier is
designed to remove heat from the amplifier
circuitry. For optimum cooling performance, this
outer shell should be exposed to as large a volume
of air as possible. Enclosing the amplifier in a
small, poorly ventilated chamber can lead to
excessive heat build-up and degraded
performance. If an installation calls for an
enclosure around the amplifier, we recommend
that this enclosure be ventilated with the aid
of a fan. In normal applications, fan-cooling
is not necessary.
safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden
jolt to the vehicle.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
serial number
In the event that your amplifier requires
service or is ever stolen, you will need to have
a record of the product’s serial number. Please
take the time to enter that number in the space
provided below. The serial number can be found
on the bottom panel of the amplifier and on the
amplifier packaging.
stupid mistakes to avoid
Remote Turn-On
Connector
(pg. 6)
• Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
CH 1 & CH 2
Speaker Outputs
(pg. 9)
CH 3 & CH 4
+12 V Power Chassis Ground
Speaker Outputs
(pg. 9)
Fuses
(pg. 5)
Connector
(pg. 5)
Connector
(pg. 5)
• Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
CHANNEL 1 (L)
CHANNEL 2 (R)
CHANNEL 3 (L)
CHANNEL 4 (R)
FUSES
Serial Number:
30A
30A
• Protect all system wires from sharp metal
edges and wear by carefully routing them,
tying them down and using grommets and
loom where appropriate.
Bridged
Bridged
Made in China
Power Status
Indicator
(pg. 11)
Channel Input
Selector
CH 1 & CH 2
Preamp Input Jacks
(pg. 6)
Protection Status
Indicator
(pg. 7)
(pg. 11)
• Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof
or in any other area that will expose the
amplifier circuitry to the elements.
CH 3 & CH 4
Bass Boost
Control
(pg. 9)
High-Level
Input Jack
(pg. 6,7)
Left & Right
Preamp Output Jacks
(pg. 9)
High Level
Input Jack
(pg. 6,7)
Bass Boost
Control
(pg. 9)
Preamp Input Jacks
(pg. 6)
Channel 1 & 2 Controls
Pre-Outs
Amplifier Inputs
Channel 3 & 4 Controls
Power
CH 3&4
Input From
Protect
LEFT
CH 1 (Left)
CH 3 (Left)
Bass Boost
Bass Boost
|
1&2 3&4
High-Level Inputs
High-Level Inputs
Off +12dB
Off +12dB
40
Low-Pass
Filter Frequency (Hz)
150
60
1. 2k
min max
Input Sens.
min max
Input Sens.
60
High-Pass
Filter Frequency (Hz)
1. 2k
40
150
High-Pass
Low-Pass
|
|
HP Off LP
Filter Mode
|
|
HP Off LP
Filter Mode
RIGHT
CH 2 (Right)
CH 4 (Right)
Input Sensitivity
Control
Low-Pass Filter
Frequency Control
(pg. 8)
High-Pass Filter
Frequency Control
(pg. 8)
Filter Mode
Selector
(pg. 8)
(pg. 7)
Filter Mode
Selector
(pg. 8)
High-Pass Filter
Frequency Control
(pg. 8)
Input Sensitivity
Control
(pg. 7)
Low-Pass Filter
Frequency Control
(pg. 8)
2
JL Audio
3
ProduCt desCriPtion
Power ConneCtions
The JL Audio J2-320.4 is a four-channel, full-
range audio amplifier utilizing
5) Run speaker cables from the speaker systems
to the amplifier mounting location.
6) Find a good, solid metal grounding point
close to the amplifier and connect the
negative power wire to it using appropriate
hardware. Use the same size power wire as the
wire connected to the “+12VDC” connection
(minimum 4 AWG), no longer than 36 inches
(90 cm) from the amplifier to the ground
connection point. In some vehicles, it may be
necessary to upgrade the battery ground wire.
(See page 5 for important notice).
Before installing the amplifier, disconnect the
negative (ground) wire from the vehicle’s battery.
This will prevent accidental damage to the system,
the vehicle and your body during installation.
Any wires run through metal barriers (such as
firewalls), must be protected with a high quality
insulating grommet to prevent damage to the
insulation of the wire. Failure to do so may result
in a dangerous short circuit.
Class B technology for all channels.
The J2-320.4 can be operated with a wide
variety of source units and system configurations.
For detailed specifications, please refer to
Appendix B (page 13).
+ 12VDC
Remote
0A
tYPiCal installation sequenCe
The following represents the sequence
Many vehicles employ small (10 AWG -
6 AWG) wire to ground the battery to the
vehicle chassis and to connect the alternator’s
positive connection to the battery. To prevent
voltage drops, these wires should be upgraded
to 4 AWG when installing amplifier systems
with main fuse ratings above 60A.
for a typical amplifier installation, using an
aftermarket source unit or OEM Interface
product. Additional steps and different
procedures may be required in some applications.
If you have any questions, please contact your
authorized JL Audio dealer for assistance.
7) Securely mount the amplifier using
appropriate hardware.
8) Connect the positive and negative power
wires to the amplifier.
9) Connect the remote turn-on wire
to the amplifier.
The J2-320.4’s “+12VDC” and “Ground”
connections are designed to accept 4 AWG power
wire. 4 AWG is a minimum power wire size for
this amplifier.
If you are installing the J2-320.4 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or larger main power wire
(depending on the overall current demands of all
the amplifiers in the system). This 2 AWG or
larger power wire should terminate into a
distribution block mounted as close to the
amplifiers as possible and should connect to the
J2-320.4 with 4 AWG power wire.
Fuse requirements
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional.
2) Run 4 AWG power wire from the battery
location to the amplifier mounting location,
taking care to route it in such a way that it
will not be damaged and will not interfere
with vehicle operation. Use 2 AWG or larger
power wire and a power distribution block if
additional amplifiers are being installed with
the J2-320.4.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4) Run signal cables and remote turn-on wire
from the source unit to the final amplifier
mounting location.
While the J2-320.4 has two 30A ATC fuses
on its power connection panel, these do nothing
to protect the vehicle from a dangerous short
circuit in the power wire. They only protect the
amplifier. It is absolutely vital that the main
power lead to the amplifier(s) in the system be
fused within 18 inches (45 cm) of the positive
battery post connection. The fuse value at each
power wire should be high enough for all of the
equipment being run from that power wire.
If only the J2-320.4 is being run from that power
wire, we recommend a 60A fuse be used. AFS or
MAXI-type fuses are recommended.
10) Connect the input cables to the amplifier.
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
13) Install the power wire fuse (60A for a
single J2-320.4) and reconnect the negative
battery post terminal.
14) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
15) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix A (page 12)
for the recommended input sensitivity
setting method.
Note: Smaller AWG numbers mean bigger wire
and vice-versa (1/0 AWG is the largest, 2 AWG is
smaller, then 4 AWG, then 8 AWG, etc.).
To connect the power and ground wires to the
amplifier, strip 1/2-inch (12 mm) of insulation
from each wire and insert the bare wire into the
the appropriate terminal block positions on the
J2-320.4. Use a Phillips screwdriver to secure the
wire via the screw on the top of each terminal.
The “GROUND” connection should be made
using 4 AWG wire and should be kept as short
as possible, while accessing a solid piece of sheet
metal in the vehicle. The surface of the sheet
metal should be sanded at the contact point
to create a clean, metal-to-metal connection
between the chassis and the termination of
the ground wire. The use of a star washer to
lock down the connection is advisable.
R)
FUSES
+
30A
30A
16) Enjoy the fruits of your labor with your
favorite music.
4
JL Audio
5
turn-on lead
The J2-320.4 is turned on and off
using a conventional +12V remote turn-
on lead, typically controlled by the
source unit’s remote turn-on output.
1) Low-Level Inputs: A standard left/
right pair of RCA type jacks in the
“Amplifier Inputs” section is used for
preamp level (low-level) signal input
on the J2-320.4. This is the preferred
connection method whenever available.
Make sure you observe correct polarity in
making the “High Level Input” connections.
Failure to do so will reduce bass and affect
stereo imaging.
If you wish to feed all four channels by using
only two channels of input, set the “CH 3&4
Input From” switch to “1&2” and use only the
inputs to channels 1 & 2.
The connections for the “High Level Inputs” plug
inPut sensitivitY Controls
wires are as follows from left to right on the plug:
The controls labeled “Input Sens.” located in
each “Channel Controls” section can be used
to match the source unit’s output voltage to the
input stage of each pair of amplifier channels
for maximum clean output. Rotating the control
clockwise will result in higher sensitivity (louder
for a given input voltage). Rotating the control
counter-clockwise will result in lower sensitivity
(quieter for a given input voltage.)
+ 12VDC
Remote
0A
Channels 1&2 (FRONT)
White: Left Positive (+)
White/Black: Left Negative (–)
Black: Common Ground (rarely used)*
Gray: Right Positive (+)
Amplifier Inputs
CH 1 (Left)
CH 3 (Left)
Gray/Black: Right Negative (–)
Channels 3&4 (REAR or SUB)
Green: Left Positive (+)
The amplifier will turn on when +12V is
present at its “Remote” input and turn off when
+12V is switched off. If a source unit does not
have a dedicated remote turn-on output, the
amplifier’s turn-on lead can be connected to +12V
via a switch that derives power from an ignition-
switched circuit.
18 AWG wire is more than adequate for
the remote turn-on connection. To connect
the remote turn-on wire to the amplifier, strip
1/2-inch (12 mm) of insulation from the wire
and insert it into the “Remote” receptacle on the
power connector. Tighten the connector down
using a Phillips screwdriver.
Green/Black: Left Negative (–)
Black: Common Ground (rarely used)*
Purple: Right Positive (+)
CH 2 (Right)
CH 4 (Right)
& 2 Controls
CH 3&4
Pr
Input From
Purple/Black: Right Negative (–)
2) High-Level Inputs: If your system does
not offer a preamp level signal option, you
can connect speaker level signals directly to
the “High-Level Inputs” connectors using
the supplied mating connectors and wire
harnesses. Simply splice the appropriate
left/right and positive/negative wires to the
included harnesses and plug the harness into
the “High-Level Inputs” connectors on the
amplifier. The J2-320.4 will attenuate the high-
level signals to make them compatible with its
input stages.
|
1&2 3&4
nputs
*The only time you will use the Common Ground
connections is with some older (pre-1980’s) factory
systems or head units that ground their speakers to
chassis ground. To use these connections, ground
the black wires on the plugs to chassis ground and
only connect the Left and Right Positive plug wires
to the factory radio outputs.
1.2k
min max
Input Sens.
-Pass
Hz)
“CH 3&4 Input From” Switch
To properly set the amplifier for maximum
clean output, please refer to Appendix A (page
12) in this manual. After using this procedure,
you can then adjust any or all “Input Sens.”
levels downward if this is required to achieve the
desired system balance.
If you wish to send four discrete channels of
input into the J2-320.4, simply use all four inputs
(Channels 1 & 2 and Channels 3 & 4) and set the
“CH 3&4 Input From” switch to “3&4”.
inPut seCtions
The J2-320.4’s has two input sections: one for
Channels 1&2 and another for Channels 3&4.
These input sections allows you to send signals to
the amplifier sections through the use of either
two or four inputs. Each input section offers
two input connection methods, one for high-
level (speaker level) signals and one for low-level
(preamp level) signals.
Channel 1 & 2 Contro
wer
In
2 Controls
CH 3&4
Pre
Do not increase any “Input Sens.” setting for
any channel(s) of any amplifier in the system
beyond the maximum level established during
the procedure outlined in Appendix A (page
12). Doing so will result in audible distortion
and possible speaker damage.
1
Input From
High-Level Inputs
|
1&2 3&4
puts
150
60
1.2k
m
I
w-Pass
High-Pass
Filter Frequency (Hz)
1.2k
Pass
min max
Input Sens.
z)
R
6
JL Audio
7
Filter Controls
“bass boost” Controls
The active filter built into each channel
section of the J2-320.4 can be used to eliminate
potentially harmful and/or undesired frequencies
from making their way through the amplifier
sections to the speaker(s). This serves to improve
tonal balance and to avoid distortion and possible
speaker failure. Correct use of these filters can
substantially increase the longevity and fidelity
of your audio system.
attenuate frequencies above the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of subwoofer(s) to one
or both of the J2-320.4’s channel pairs in a
bi-amplified system.
Each channel pair of the J2-320.4 includes a
single band, boost-only bass equalizer controlled
by a rotary knob marked “Bass Boost”.
This control has a boost range of 0dB (full-
counterclockwise) to +12dB (full-clockwise) and
is centered at 45 Hz.
The preamp output signal is not affected by the
“Bass Boost” processing selected for the amplifier
or by any crossover filter selected (if the input
signal is full-range, the preamp output will be
full-range).
2) “Filter Freq. (Hz)” The J2-320.4 has separate
Filter Frequency controls in each Channel
Controls section for the low-pass filter and the
high-pass filter. You will only use one of these
in each channel section, depending on which
“Filter Mode” you have selected (or none of
them if you have selected the “Off” position for
the “Filter Mode”).
Note: The signal level of the “Preamp Output” is
always line-level (low voltage).
sPeaker outPuts
The J2-320.4’s speaker outputs are designed to
accept 16 AWG - 8 AWG wire.
Each pair of the J2-320.4’s channels are
designed to deliver power into speaker loads equal
to or greater than 2 ohms per channel when using
a “stereo” configuration and speaker loads equal
to or greater than 4 ohms per bridged pair of
channels when using a “bridged” configuration.
Po
Bass Boost
Channel 1 & 2 Contro
Power
I
Off +12dB
Bass Boost
The High-Pass filters in the J2-320.4 are fully
variable between 60 Hz and 1.2 kHz (1200 Hz) via
the control knobs labeled “High-Pass”. The “8
o’clock” position corresponds to 80 Hz and is a
good starting point for system tuning.
4
L
High-Level Inputs
|
|
HP Off LP
Filter Mode
Off +12dB
40
Low-Pass
Filter Frequency (Hz)
150
60
1.2k
High-Pass
|
|
HP Off LP
Filter Mode
Channel 1 & 2 Contr
The Low-Pass filters in the J2-320.4 are fully
variable between 40 Hz and 150 Hz via the
control knobs labeled “High-Pass”. The “12
o’clock” position corresponds to 80 Hz and is a
good starting point for system tuning.
Pre-outs
Power
The J2-320.4 incorporates a pass-through
preamp output section, so that additional
amplifiers can be easily added to the system.
This pass-through pre-amp output delivers a
summed stereo signal , combining the Ch 1 and 3
signals into a Left Preamp Output Signal and the
Ch. 2 and 4 signals into a Right Channel Preamp
Output signal.
Bass Boost
High-Level Inputs
1) “Filter Mode” Control: The J2-320.4 employs a
12dB per octave filter for each pair of channels
(one filter for channels 1&2 and another filter
for channels 3&4). Each of these filters can
be configured independently into one of two
filter types or defeated completely by way of the
three-position “Filter Mode” switches:
Off +12dB
40
Low-Pass
Filter Frequency (Hz)
150
60
1.2k
High-Pass
|
|
HP Off LP
Filter Mode
“HP” (High-Pass): Configures the filter to
attenuate frequencies below the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of component speakers
to one or both of the J2-320.4’s channel pairs in
a bi-amplified system.
Pre-Outs
Speaker loads below 2 ohms nominal per
channel are not recommended and may cause
the amplifier to initiate a protection mode.
&4
om
LEFT
CH
&4
Off”: Defeats the filter completely, allowing
the full range of frequencies present at the
inputs to feed the amplifier. This is useful
for systems utilizing outboard crossovers or
requiring full-range reproduction from one or
both of the J2-320.4’s channel pairs.
max
ens.
RIGHT
CH 2
“LP” (Low-Pass): Configures the filter to
8
JL Audio
9
bridging Considerations
amPliFier status indiCator ligHts &
ProteCtion CirCuitrY
There are two status indicator lights on the
control panel of the amplifier.
serviCing Your tma amPliFier
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The J2-320.4 has been designed for
bridging of its channel pairs without the need for
input inversion adaptors.
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only
or right-only signal to a pair of the J2-320.4’s
channels, use a “Y-Adaptor” to split the single
channel signal into both left and right RCA
inputs. This option is useful when using a
pair of the J2-320.4’s channels to drive left
channel speakers only and the other pair of
the J2-320.4’s channels to drive right channel
speakers only.
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
Ch
ols
Power
Protect
Bass Boost
Bass Bo
To bridge a pair of channels, use the
H
el Inputs
“Left +” and “Right –” speaker connectors only
(the “Left –” and “Right +” remain unused).
When bridged, each channel will deliver
optimum power into a 4 ohm load.
2) Left + Right Channel Information:
When bridged and fed by a stereo input, a pair
of the J2-320.4’s channels will automatically
combine the left and right channels into a
summed mono (left + right) channel. This
option is useful when using a pair of the
J2-320.4’s channels to drive a subwoofer system
or a summed mono center channel.
Off +12dB
Off
+
If you have any questions about the installation
or setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
40
150
2k
s
40
150
Low-Pass
Low-Pass
|
HP Of
Filter M
|
|
HP Off LP
Filter Mode
Frequency (Hz)
Filter Fr
When a pair of channels are bridged, they
will deliver 160W x 1 into a 4 ohm load or
120W x 1 into an 8 ohm load. Operating a
pair of bridged channels into a load lower
than 4 ohms is not recommended.
1) “Power” (Green): lights to indicate that the
amplifier is turned on and operating normally.
Located at the far left of the control panel.
Jl audio technical support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
2) “Protect” (Red): Indicates that the amplifier
protection circuitry has been activated
Because a bridged pair of channels requires that
both channels receive input, you need to
connect both left and right inputs to the source
unit. Connection of only one input will result in
reduced power output, increased distortion and
can cause the amplifier to overheat.
to prevent product failure due to thermal
overload, short-circuit or a dangerously
low impedance connected to the amplifier
outputs. Connecting the speaker outputs
to an impedance lower than 2 ohms stereo
(4 ohms bridged) will cause this protection
mode to activate. When this protection mode
is activated, the amplifier will shut down to
protect its circuitry. When the problem is
corrected, the amplifier will return to normal
operation and the “Protect” LED will shut off.
Do not do this!
When a pair of the J2-320.4’s channels are
operating in bridged mode, the output will be in
mono (only one channel). This mono channel
can contain right channel only information,
left channel only information or the sum of
the information from both the right and left
channels. In order to achieve one of these options,
configure the inputs to that pair of channels in
one of these two ways:
10
JL Audio
11
aPPendix a:
aPPendix b:
input sensitivity level setting
8) Increase the “Input Sens.” control until the
target voltage is observed with the voltmeter.
9) Once you have adjusted the amplifier to
its maximum low-distortion output level,
reconnect the speaker(s). The “Input Sens.”
controls can now be adjusted downward if the
amplifier requires attenuation to achieve the
desired system balance.
J2-320.4 specifications
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a
few minutes using equipment which is commonly
available in installation bays.
general specifications:
Recommended Fuse Value: 60A
Recommended Fuse Type: AFS, AGU or MaxiFuse™ at
battery, 2 x 30A ATC fuses on amplifier chassis
necessary equipment
input sections:
• Digital AC Voltmeter
No. of Inputs: Two Stereo Pairs
• CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for a
midrange application). Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
Low-Level Inputs: Single-ended with RCA jack inputs
Low-Level Input Range: 200mV - 4V RMS
High-Level Inputs: Single-ended with molded connector
High-Level Input Range: 2V - 10V RMS
Do not increase any “Input Sens.” setting for
any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
amplifier section:
Amplifier Topology: Class B with
complementary bi-polar output stage
Power Supply: PWM switching type, unregulated
the nine-step Procedure
1) Disconnect the speaker(s) from the
amplifier’s speaker output connectors.
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if used)
and amplifier. Set fader control to center position
and subwoofer level control to 3/4 of maximum.
If connected, set the amplifier’s Remote Bass
Control at maximum (full clockwise).
It will be necessary to re-adjust the
“Input Sens.” for the affected channels if any
equalizer boost is activated after setting the
“Input Sens.” with this procedure. This applies
to any EQ boost circuit, including source unit
tone controls or EQ circuits. EQ cuts will not
require re-adjustment.
Rated Power with less than 1% THD (14.4V supply):
Stereo, all channels driven:
60W RMS x 4 @ 4 ohms, 80W RMS x 4 @ 2 ohms
Bridged, all channels driven:
120W RMS x 2 @ 8 ohms, 160W RMS x 2 @ 4 ohms
Frequency Response: 10 Hz - 25 kHz +/- 0.5 dB
3) Turn the “Input Sens.” control all the
way down.
Crossover sections:
Filter Type: 12dB/octave Butterworth
nom.
impedance
target aC voltage
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Using the chart on this page, determine the target
voltage for input sensitivity adjustment according
to the nominal impedance of the speaker system
connected to the amplifier outputs.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (within the frequency
range to be amplified) at 3/4 source unit
volume.
stereo
bridged
31 V
with continuously variable low-pass cutoff frequency
selection from 40-150 Hz and high-pass cutoff frequency
selection from 60Hz - 1.2 kHz.
15.5 V
15.5 V
15.5 V
14 V
8Ω
6Ω
4Ω
3Ω
2Ω
28 V
Configurable as Low-Pass or High-Pass. Defeatable.
25 V
not recommended
not recommended
Preamp output:
2-Channel, pass-through with unity gain, RCA-type jacks.
12.5 V
dimensions (lxwxH):
15.40" x 9.60" x 2.15" (391 mm x 244 mm x 55 mm)
7) Connect the AC voltmeter to the speaker output
connectors of the amplifier. Make sure you test
the voltage at the correct connectors (+ and –).
Due to ongoing product development, all specifications are subject to
change without notice.
12
JL Audio
13
aPPendix C: troublesHooting
“How do i properly set the input sensitivity on my amplifier”
“my amplifier turns on, but there is no output”
Check the input signal using an AC voltmeter to measure the
Please refer to Appeaset the input sensitivity for maximum, low-
distortion output.
voltage from the source unit while an appropriate test tone is
played through the source unit (disconnect the input cables
from the amplifier prior to this test). The frequency used
should be in the range that is to be amplified by the amplifier
(example: 50 Hz for a sub bass application or 1 kHz for a full
range / high-pass application). A steady, sufficient voltage
(between 0.2 and 8.0-volts) should be present at the output of
the signal cables.
“my amplifier doesn’t turn on”
Check the fuse, not just visually, but with a continuity meter. It is
possible for a fuse to have poor internal connections that
cannot be found by visual inspection. It is best to take the
fuse out of the holder for testing. If no problem is found with
the fuse, inspect the fuse-holder.
Check the integrity of the connections made to each of the
“+12VDC”, “Ground”, and “Remote” terminals. Ensure
that no wire insulation is pinched by the terminal set screw
and that each connection is tight.
Check to make sure there is +12V at the “Remote” connection of the
amplifier. In some cases, the turn-on lead from the source unit
is insufficient to turn on multiple devices and the use of a relay
is required. To test for this problem, jump the “+12VDC” wire
to the “Remote” terminal to see if the amplifier turns on. If this
does not work, proceed to the next step.
Check the output of the amplifier. Using the procedure explained in
the previous check item (after plugging the input cables back
into the amplifier) test for output at the speaker outputs of
the amplifier. Unless you enjoy test tones at high levels, it is
a good idea to remove the speaker wires from the amplifier
while doing this. Turn the volume up approximately half
way. 5V or more should be measured at the speaker outputs.
This output level can vary greatly between amplifiers but it
should not be in the millivolt range with the source unit at
half volume. If you are reading sufficient voltage, check your
speaker connections as explained below.
“my amplifier’s output fluctuates when i tap on it or hit a bump”
Check the connections to the amplifier. Make sure that the
Check to ensure that the speaker wires are making a good
connection with the metal inside the terminal block. The
speaker wire connectors are designed to accept up to 8 AWG
wire. Make sure to strip the wire to allow for a sufficient
connection with the metal inside the terminal block.
insulation for all wires has been stripped back far enough to
allow a good contact area inside the terminal block.
Check the input connectors to ensure that they all are making good
contact with the input jacks on the amplifier.
14
JL Audio
15
installation notes:
Use this diagram to document your amplifier’s switch and control positions.
Channel 1 & 2 Controls
Pre-Outs
Amplifier Inputs
Channel 3 & 4 Controls
Power
CH 3&4
Protect
Input From
LEFT
CH 1 (Left)
CH 3 (Left)
Bass Boost
Bass Boost
|
1&2 3&4
High-Level Inputs
High-Level Inputs
Off +12dB
Off +12dB
40
Low-Pass
Filter Frequency (Hz)
150
60
1.2k
min max
Input Sens.
min max
Input Sens.
60
High-Pass
Filter Frequency (Hz)
1.2k
40
150
High-Pass
Low-Pass
|
|
HP Off LP
Filter Mode
|
|
HP Off LP
Filter Mode
RIGHT
CH 2 (Right)
CH 4 (Right)
16
JL Audio
17
installation notes:
installation notes:
18
JL Audio
19
|