JVC CD Player GET0561 001A User Manual

Thank you for purchasing a JVC product.  
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best  
possible performance from the unit.  
KD-S15  
CD RECEIVER: INSTRUCTIONS/INSTALLATION  
Installation/connection are explained at the last section of this manual (reverse page, indicated with  
symbol).  
For customer Use:  
Enter below the Model No. and Serial No. which  
are located on the top or bottom of the cabinet.  
Retain this information for future reference.  
0508DTSMDTJEIN  
Model No.  
Serial No.  
GET0561-001A  
[J]  
EN  
© 2008 Victor Company of Japan, Limited  
ESPAÑOL  
ENGLISH  
INFORMATION (For U.S.A.)  
MAINTENANCE  
How to clean the connectors  
Wipe the connectors with  
a cotton swab or cloth  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
To keep discs clean  
Wipe in a straight line from center of disc to  
edge. Do not use liquid cleaners, thinners, or  
benzene.  
moistened with alcohol.  
Connectors  
Moisture condensation  
To play new discs  
Remove any rough areas from the inner and  
outer edges of the disc.  
Moisture may condense on the lens inside the unit. Eject  
the disc and leave the unit turned on for a few hours until  
the moisture has evaporated.  
Caution  
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.  
Do not use the following discs:  
IMPORTANT FOR LASER PRODUCTS  
1. CLASS 1 LASER PRODUCT  
Single CD—8 cm (3-3/16”) disc  
Warped disc  
Sticker and sticker residue  
Stick-on label  
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified  
service personnel.  
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.  
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical  
instruments.  
Transparent or semi-transparent  
parts on its recording area  
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.  
Unusual shape  
C-thru Disc (semi-transparent disc)  
PREPARATIONS  
[European Union only]  
How to reset your unit  
Detaching the control panel  
Reset the unit after installation is complete.  
For safety...  
Warning  
• Do not raise the volume level too much, as this will block  
outside sounds, making driving dangerous.  
• Stop the car before performing any complicated  
operations.  
If you need to operate the unit while driving, be sure to  
look around carefully or you may be involved in a traffic  
accident.  
Your preset adjustments will also be erased.  
Attaching the control panel  
Temperature inside the car...  
Caution on volume setting  
If you have parked the car for a long time in hot or cold  
weather, wait until the temperature in the car becomes  
normal before operating the unit.  
Discs produce very little noise compared with other sources.  
Lower the volume before playing a disc to avoid damaging  
the speakers by the sudden increase of the output level.  
How to forcibly eject a disc  
MORE ABOUT THIS UNIT  
Be careful not to drop the disc when it ejects.  
If this does not work, reset your unit.  
General  
Basic operations  
• This unit has been designed to reproduce CDs/CD Texts,  
and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD  
(CD-DA).  
• After ejecting a disc, “NO DISC” appears and you cannot  
operate some of the buttons. Insert another disc or press  
SRC to select another playback source.  
• By pressing SRC on the unit, you can also turn on the  
power. If the source is ready, playback also starts.  
• If you turn off the power while listening to a disc, disc  
play will start from where it had been stopped previously  
next time you turn on the power.  
Basic settings  
Enter PSM menu.  
Cancel the display  
demonstration  
Set the clock  
• When no disc is loaded in the unit, you cannot select “CD”  
as the playback source.  
Playing a CD-R or CD-RW  
• Use only “finalized” CD-Rs or CD-RWs.  
• This unit can play back multi-session discs; however,  
unclosed sessions will be skipped while playing.  
• Some CD-Rs or CD-RWs may not be played back on this  
unit:  
– Discs are dirty or scratched.  
– Moisture condensation has occurred on the lens inside  
the unit.  
– The pickup lens inside the unit is dirty.  
– The files on the CD-R/CD-RW are written using the  
“Packet Write” method.  
– There are improper recording conditions (missing data,  
etc.) or media conditions (stained, scratched, warped,  
etc.).  
Select an item.  
Adjust.  
Tuner operations  
• During SSM search...  
– All previously stored stations are erased and the  
stations are stored anew.  
– Received stations are preset in No. 1 (lowest  
frequency) to No. 6 (highest frequency).  
– When SSM is over, the station stored in No. 1 will be  
automatically tuned in.  
Adjust the hour.  
Adjust the minute.  
Deactivate the display  
demonstration.  
Disc operations  
Caution for DualDisc playback  
• The Non-DVD side of a “DualDisc” does not comply with  
the “Compact Disc Digital Audio” standard. Therefore, the  
use of Non-DVD side of a DualDisc on this product may  
not be recommended.  
Finish  
• CD-RWs may require a longer readout time since the  
reflectance of CD-RWs is lower than that of regular CDs.  
1– EN  
 
General settings—PSM  
SPECIFICATIONS  
Enter PSM menu.  
Select an item.  
Adjust.  
Finish  
CD player section  
Audio amplifier section  
Type:  
Compact disc player  
Power Output:  
Signal Detection System: Non-contact optical pickup  
(semiconductor laser)  
Number of channels:  
Frequency Response:  
Dynamic Range:  
20 W RMS × 4 Channels at 4  
1% THD+N  
Signal to Noise Ratio:  
and  
2 channels (stereo)  
5 Hz to 20 000 Hz  
93 dB  
Indication  
DEMO  
Item ( : Initial) Setting  
80 dBA (reference: 1 W into 4  
)
DEMO ON  
DEMO OFF  
ON  
:
:
:
:
The display demonstration will be activated automatically if no operation is  
done for about 20 seconds.  
Cancels.  
Signal-to-Noise Ratio:  
Wow and Flutter:  
98 dB  
Load Impedance:  
Tone Control Range:  
4
(4  
Bass:  
Mid-range: 12 dB at 1 kHz  
Treble: 12 dB at 7.5 kHz  
40 Hz to 20 000 Hz  
load (full scale)  
to 8  
allowance)  
Less than measurable limit  
12 dB at 60 Hz  
CLK DISP*1  
The clock time is shown on the display at all times when the power is turned  
General  
off.  
Frequency Response:  
Power Requirement:  
Operating Voltage: DC 14.4 V  
(11 V to 16 V allowance)  
Negative ground  
OFF  
Cancels; pressing DISP will show the clock time for about 5 seconds when the  
power is turned off.  
Line-Out Level/Impedance: 2.5 V/20 k  
Output Impedance: 1 k  
Subwoofer-Out Level/Impedance:  
2.5 V/20 kΩ load (full scale)  
Grounding System:  
Allowable Operating Temperature:  
0°C to +40°C (32°F to 104°F)  
Dimensions (W × H × D):  
Installation Size (approx.):  
CLOCK H (Hour)  
1 12  
:
:
[Initial: 1 (1:00)]  
[Initial: 00 (1:00)]  
CLOCK M (Minute) 00 59  
DIMMER  
ON  
OFF  
:
:
Dims the display and button illumination.  
Cancels.  
182 mm × 52 mm × 160 mm  
(7-3/16” × 2-1/16” × 6-5/16”)  
Panel Size (approx.):  
188 mm × 58 mm × 5 mm  
(7-7/16” × 2-5/16” × 1/4”)  
Mass (approx.):  
Tuner section  
Frequency Range:  
SCROLL  
ONCE  
AUTO  
OFF  
:
:
:
Scrolls the displayed information once.  
Repeats scrolling (at 5-second intervals).  
Cancels.  
FM: 87.5 MHz to 107.9 MHz  
(with channel interval set to 100 kHz or 200 kHz)  
87.5 MHz to 108.0 MHz  
(with channel interval set to 50 kHz)  
AM: 530 kHz to 1 710 kHz  
• Pressing DISP for more than one second can scroll the display regardless of  
the setting.  
1.3 kg (2.9 lbs) (excluding accessories)  
(with channel interval set to 10 kHz)  
531 kHz to 1 602 kHz  
(with channel interval set to 9 kHz)  
Design and specifications are subject to change without  
notice.  
L/O MODE  
WOOFER*2  
AUX ADJ  
REAR  
:
:
Select if the REAR LINE OUT terminals are used for connecting the speakers  
(through an external amplifier).  
Select if the REAR LINE OUT terminals are used for connecting a subwoofer.  
WOOFER  
If a kit is necessary for your car, consult your telephone  
directory for the nearest car audio speciality shop.  
[FM Tuner]  
Usable Sensitivity: 11.3 dBf (1.0 μV/75  
LOW  
MID  
HIGH  
:
:
:
Frequencies lower than 90 Hz are sent to the subwoofer.  
Frequencies lower than 135 Hz are sent to the subwoofer.  
Frequencies lower than 180 Hz are sent to the subwoofer.  
)
50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75  
Alternate Channel Selectivity (400 kHz): 65 dB  
Frequency Response: 40 Hz to 15 000 Hz  
Stereo Separation: 35 dB  
)  
Having TROUBLE with operation?  
A.ADJ 00  
– A.ADJ 05  
:
Adjust the auxiliary input level to avoid the sudden increase of the output  
level when changing the source from external component connected to the  
AUX input jack on the control panel.  
Please reset your unit  
Still having trouble??  
[AM Tuner]  
Sensitivity/Selectivity: 20 μV/35 dB  
Call 1-800-252-5722 (USA ONLY)  
AMP GAIN*3  
AREA  
LOW PWR  
HIGH PWR  
AREA US  
AREA EU  
AREA SA  
:
:
:
:
:
VOL 00 – VOL 30 (Select if the maximum power of each speaker is less than  
50 W to prevent the speaker from being damaged.)  
VOL 00 – VOL 50  
When using in North/Central/South America. AM/FM intervals are set to  
10 kHz/200 kHz.  
When using in any other areas. AM/FM intervals are set to 9 kHz/50 kHz  
(100 kHz during auto search).  
When using in South American countries. AM/FM intervals are set to 10 kHz/  
100kHz.  
PREPARATION  
You need the installation kits which corresponds to your car.  
• Mark all the check boxes (  
) to make sure you have follow the instructions and the listed parts.  
1
*
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select “OFF” to  
save the car’s battery.  
Displayed only when “L/O MODE” is set to “WOOFER.”  
The volume level automatically changes to “VOL 30” if you change to “LOW PWR” while the volume level is set higher than  
“VOL 30.”  
Check the battery system in your car  
2
3
*
*
12 V DC, NEGATIVE ground  
TROUBLESHOOTING  
Prepare this before installation  
Symptoms  
Remedies/Causes  
• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.  
• Check the cords and connections.  
• The buttons on the unit do not work as you If you press M MODE, some buttons work differently from it  
intended.  
original function. Wait for 5 seconds or press M MODE again.  
TROUBLESHOOTING  
• The fuse blows.  
• This unit does not work at all.  
Reset the unit.  
* Are the red and black leads connected correctly?  
• SSM automatic presetting does not work. Store stations manually.  
• Power cannot be turned on.  
* Is the yellow lead connected?  
• Static noise while listening to the radio.  
• Disc ejects.  
Connect the antenna firmly.  
Insert the disc correctly.  
• No sound from the speakers.  
* Is the speaker output lead short-circuited?  
• Sound is distorted.  
* Is the speaker output lead grounded?  
* Are the “–” terminals of L and R speakers grounded in common?  
• CD-R/CD-RW cannot be played back.  
• Tracks on the CD-R/CD-RW cannot be  
skipped.  
• Insert a finalized CD-R/CD-RW.  
• Finalize the CD-R/CD-RW with the component which you used  
for recording.  
• Noise interfere with sounds.  
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?  
• This unit becomes hot.  
* Is the speaker output lead grounded?  
* Are the “–” terminals of L and R speakers grounded in common?  
• Disc can be neither played back nor ejected. • Unlock the disc.  
• Eject the disc forcibly.  
• This unit does not work at all.  
• Disc sound is sometimes interrupted.  
• Stop playback while driving on rough roads.  
* Have you reset your unit?  
• Change the disc.  
• Check the cords and connections.  
• “NO DISC” appears on the display.  
• “PLEASE” and “EJECT” appear alternately  
on the display.  
Insert a playable disc into the loading slot.  
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United  
States and/or other countries.  
3 – EN  
 
Parts list for installation and connection  
A
D
B
C
Control panel  
Power cord  
Sleeve  
Trim plate  
G
I
J
K
Mounting bolt—  
M4 x 5 mm (M4 x 1/4");  
M5 x 12.5 mm (M5 x 1/2")  
E
F
H
Handles  
Remote controller  
Battery  
Washer (ø5)  
Lock nut (M5)  
Rubber cushion  
INSTALLATION  
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.  
In dash-mounting  
Removing the unit  
Before removing the unit, release the rear section.  
When you stand the unit, be careful not to  
damage the fuse on the rear.  
Do the required electrical  
connections.  
Bend the appropriate tabs  
to hold the sleeve firmly  
in place.  
When using the optional stay  
When installing the unit without using the sleeve  
Stay (option)  
In a Toyota car for example, first remove the car radio and install the unit in its place.  
Fire wall  
* Not supplied for this unit.  
Flat type screws—M5 × 8 mm (M5 × 3/8")*  
Dashboard  
Bracket*  
Screw (option)  
Flat type screws  
—M5 × 8 mm (M5 × 3/8")*  
Install the unit at an angle of  
less than 30˚.  
Pocket  
Bracket*  
ELECTRICAL CONNECTIONS  
Make sure to disconnect the battery’s negative terminal.  
• Be sure to ground this unit to the car’s chassis again after installation.  
High  
Note:  
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the  
maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page “General setting — PSM“ of the INSTRUCTIONS.).  
Heat sink  
Typical connections  
Rear ground terminal  
Connecting the external amplifier or subwoofer  
Remote lead  
Y-connector *1  
Rear line out  
Remote lead (blue with white stripe)  
Antenna  
terminal  
Set “L/O MODE” to “REAR”  
(See “General settings—PSM.”)  
You can connect a power amplifier for  
rear speakers.  
15 A fuse  
To the remote lead of other equipment  
or automatic antenna if any  
Ignition switch  
Black  
To the metallic body  
or chassis of the car  
Connect only the front speakers if your  
speaker system is two-speaker system.  
JVC Amplifier  
Rear  
speakers  
To a live terminal in the  
fuse block connecting to the  
car battery (bypassing the  
ignition switch) (constant  
12 V)  
White with black stripe  
Right  
Yellow *2  
Front speakers  
Left  
Not supplied for this unit.  
Set “L/O MODE” to “WOOFER”  
(See “General settings—PSM.”)  
You can also connect a subwoofer to  
the REAR LINE OUT terminals.  
Front speaker (left)  
White  
1
2
*
*
Fuse block  
Before checking the operation of this unit prior to installation, this  
lead must be connected, otherwise the power cannot be turned on.  
Firmly attach the ground wire to the metallic body or to the chassis  
of the car—to the place uncoated with paint (if coated with paint,  
remove the paint before attaching the wire). Failure to do so may  
cause damage to the unit.  
Gray with black stripe  
Red  
To an accessory terminal in  
the fuse block  
3
*
Front speaker (right) Gray  
Green with black stripe  
or  
JVC Amplifier  
Subwoofer  
Blue with white  
stripe  
To the remote lead of other  
equipment or automatic antenna if  
any (200 mA max.)  
4
*
Signal cord (not supplied for this unit)  
Rear speaker (left)  
Green  
PRECAUTIONS on power supply and speaker connections  
Purple with black stripe  
Rear speaker (right)  
Purple  
4 – EN  
 

Indesit Washer 15666 User Manual
Intel Network Card 82540EP User Manual
Invacare Mobility Aid Crossfire T6 User Manual
JVC Security Camera VN H237U User Manual
JVC Stereo Receiver RX 8020VBK User Manual
Kenwood Automobile Accessories KMC 38GPS User Manual
Kenwood Car Video System KDV MP7032 User Manual
KitchenAid Toaster KCO273 User Manual
Konica Minolta Copier CF5001 User Manual
Korg Musical Instrument Ax3000b User Manual