JVC DVD Recorder CU VD20U User Manual

ENGLISH  
DEUTSCH  
FRANÇAIS  
NEDERLANDS  
DVD Burner  
INSTRUCTIONS  
DVD-brenner  
BRUKSANVISNING  
Записывающее устройство  
для дисков DVD  
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ  
DVD-Brenner  
BEDIENUNGSANLEITUNG  
Graveur de DVD  
MANUEL D’UTILISATION  
CASTELLANO  
ESPAÑOL  
Пристрій для запису DVD  
ІНСТРУКЦІЯ  
DVD-brander  
GEBRUIKSAANWIJZING  
Vypalovací jednotka DVD  
PŘÍRUČKA K OBSLUZE  
ITALIANO  
DANSK  
Grabador de DVD  
MANUAL DE INSTRUCCIONES  
Nagrywarka DVD  
INSTRUKCJA OBSŁUGI  
Masterizzatore di DVD  
ISTRUZIONI  
SUOMI  
DVD-író  
HASZNÁLATI UTASĺTÁSA  
DVD-brænder  
INSTRUKTIONSBOG  
SVENSKA  
NORSK  
Gravador de DVD  
INSTRUÇÕES  
DVD-tallennin  
KÄYTTÖOHJE  
DVD 刻录机  
使用说明书  
РУССКИЙ  
DVD-brännare  
BRUKSANVISNING  
DVD 燒錄器  
УКРАЇНСЬКА  
ČEŠTINA  
POLSKI  
CU-VD20  
U/E/EK/ER/AA/AC/AG/AS/TW  
MAGYAR  
PORTUGUÊS  
For Customer Use:  
Enter the Model No. and Serial  
No. (located on the bottom of the  
burner) below. Retain this  
information for future reference.  
Model No.  
Serial No.  
LYT1728-001A  
 
• Do not insert or remove the plug when your hands are wet.  
• Fully insert the plug into the outlet.  
DO be careful with glass panels or doors on equipment.  
DON’T continue to operate the equipment if you are in any doubt  
about it working normally, or if it is damaged in any way ^ switch  
off, withdraw the mains plug and consult your dealer.  
DON’T remove any fixed cover as this may expose dangerous  
voltages.  
DON’T leave equipment switched on when it is unattended unless  
it is specifically stated that it is designed for unattended operation  
or has a standby mode. Switch off using the switch on the  
equipment and make sure that your family knows how to do this.  
Special arrangements may need to be made for infirm or  
handicapped people.  
DON’T use equipment such as personal stereos or radios so that  
you are distracted from the requirements of road safety. It is illegal  
to watch television whilst driving.  
DON’T listen to headphones at high volume, as such use can  
permanently damage your hearing.  
DON’T obstruct the ventilation of the equipment, for example with  
curtains or soft furnishings. Overheating will cause damage and  
shorten the life of the equipment.  
DON’T use makeshift stands and NEVER fix legs with wood  
screws ^ to ensure complete safety always fit the manufacturer’s  
approved stand or legs with the fixings provided according to the  
instructions.  
DON’T allow electrical equipment to be exposed to rain or  
moisture.  
ABOVE ALL  
• Keep dust and metal objects away from the plug.  
• Do not damage the cord.  
• Place the cord where it will not trip someone up.  
• Do not use when thunder can be heard.  
• Do not dismantle.  
• Do not use for any product other than this one.  
Do not play the provided CD-ROM with an audio player. Doing so  
may damage the circuits or speakers.  
Safety Precautions for Discs  
Do not use the following discs.  
Cracked discs  
Deeply scratched discs  
Installation  
Do not install in any of the following locations.  
Humid location  
Location of 60 °C or above  
Location subject to direct sunlight  
Location where overheating is likely  
Dusty or smoky locations  
Locations subject to oily smoke or steam such as a kitchen  
counter or beside a humidifier  
Unstable location  
Bathroom  
Dusty places  
Slanted location  
NEVER let anyone especially children push anything into holes,  
slots or any other opening in the case ^ this could result in a  
fatal electrical shock;  
NEVER guess or take chances with electrical equipment of any  
kind ^ it is better to be safe than sorry!  
ATTENTION:  
IMPORTANT (for owners in the U.K.)  
On placing the unit:  
Connection to the mains supply in the United Kingdom.  
DO NOT cut off the mains plug from this equipment.  
If the plug fitted is not suitable for the power points in your home or the  
cable is too short to reach a power point, then obtain an appropriate  
safety approved extension lead or consult your dealer.  
In the unlikely event of the plug fuse failing be sure to replace the  
fuse only with an identical approved type, as originally fitted, and  
to replace the fuse cover. If the fuse fails again consult your  
nearest JVC dealer.  
Some TVs or other appliances generate strong magnetic fields. Do not  
place such appliances on top of the unit as it may cause picture  
disturbance.  
When moving the product:  
Press C/B to turn off the power, and wait at least 30 seconds before  
unplugging the power cord. Then, wait at least 2 minutes before  
moving the product.  
Cleaning Procedure  
If nonetheless the mains plug is cut off be sure to remove the fuse and  
dispose of the plug immediately, to avoid possible shock hazard by  
inadvertent connection to the mains supply.  
IMPORTANT:  
Be sure to unplug the burner before beginning cleaning.  
Do not use liquid or aerosol cleaners.  
Ensure that no moisture or liquid comes into contact with the  
drive during cleaning.  
Exterior of the Burner:  
Wipe dirt off with a dry cloth.  
Disc Tray:  
Wipe off dirt with a soft dry cloth.  
If this product is not supplied fitted with a mains plug then follow the  
instructions given below:  
DO NOT make any connection to the Larger Terminal coded E or  
Green.  
The wires in the mains lead are coloured in accordance with the  
following code:  
Blue to N (Neutral) or Black  
Brown to L (Live) or Red  
If these colours do not correspond with the terminal identifications of  
your plug, connect as follows:  
Blue wire to terminal coded N (Neutral) or coloured black.  
Brown wire to terminal coded L (Live) or coloured Red.  
If in doubt — consult a competent electrician.  
Disc:  
Gently wipe from the inner edge to  
the outer edge with a soft cloth.  
Storage:  
Make sure that discs are kept in their cases. If discs are piled on  
top of one another without their protective cases, they can be  
damaged. Do not put discs in a location where they may be  
exposed to direct sunlight, or in a place where the humidity or  
temperature is high. Avoid leaving discs in your car!  
The C/B button does not completely shut off mains power from the unit,  
but switches operating current on and off. ABB shows electrical power  
standby and ACB shows ON.  
Safety Precautions for the Burner  
Be sure to observe the following precautions. Failing to do so may  
result in electric shock, fire, injury, or malfunction.  
Do not disassemble, dismantle, or modify the equipment.  
Requests for repair and inspection should be made to the dealer.  
Do not insert metal or combustible objects or pour water or other  
liquids inside the burner.  
Region Codes  
Region codes are numbers for restricting DVD video playback. The  
world is separated into six regions and each region is identified by  
a number. If the number for a disc does not match the number for  
the player, the disc cannot be played on the player. (The initial  
region code is indicated on the label on the bottom of the burner.)  
Turn off the power when connecting equipment.  
Changing the region codes  
Remove the plug when the burner will not be used for a  
prolonged time or prior to cleaning (electricity flows through the  
equipment even when the power is off).  
You can change the region code to play a DVD that has a different  
code. (The code cannot be changed for some playback software.)  
When you insert the disc, the Caution screen appears. Follow the  
on-screen instructions to change the code.  
Do not block the ventilation holes of the burner.  
Do not use where there is condensation. Suddenly carrying the  
burner from a cold location to a hot location may result in the  
formation of drops, which may cause a malfunction or failure.  
Do not cause the burner to vibrate when discs are in.  
The region code for the burner can be changed 4 times only. The  
code set the fourth time becomes the final code, so be sure to set  
a frequently used code. Take sufficient care when changing the  
code.  
Safety Precautions for Accessories  
When using the AC adapter, the power cord, and the USB cable,  
be sure to observe the following precautions. Failing to do so may  
result in electric shock, fire, injury, or malfunction.  
Disclaimer  
JVC accepts no liability whatsoever for loss of data resulting from  
inappropriate connections or handling.  
EN 3  
 
Accessories  
AC Adapter (AP-V400U )  
Power Cord  
USB Cable  
*
CD-ROM  
Blank Disc  
(DVD-R)  
Stand  
CAUTION:  
Do not use AC adapter, power cord and USB cable other than those provided with this burner. Doing so may result in electric shock or fire.  
NOTE:  
043-124000-I2 (AC Adapter) is also available for customer using CU-VD20AC/AG/AS.  
*
Guide to Parts and Controls  
Front  
Rear  
A
B C  
D
EF  
A Power Button (C/B)  
B Eject Button  
C Power Lamp  
D Disc Tray  
E DC Connector  
F USB Connector  
Placing the Burner  
This burner can be used either in the horizontal or vertical orientation. When using in the vertical orientation, align the vent of the burner and  
the provided stand then place and fix the burner securely on the stand.  
Bottom Surface  
Stand (provided)  
Vent  
Inserting A Disc  
When handling a disc, be sure not to touch the playback/recording side of the disc.  
8 Horizontal orientation  
8 Vertical orientation  
4 EN  
 
Connections  
AC Adapter  
(provided for the burner)  
B
Power Cord  
(Provided)  
Hard Disk Camera  
G
F
C
D
Rear of burner  
To AC Outlet  
To DC Connector  
H
A
To USB Connector  
USB Cable (Provided)  
AC Adapter (provided for the camera)  
E
Connecting to the Camera  
A Connect the AC adapter to the burner.  
B Connect the power cord to the AC adapter.  
C Connect the power cord to an AC outlet.  
D Connect the provided USB cable to the USB connector of the burner.  
E Connect the camera to an AC outlet. (Refer to the instruction manual for the camera.)  
F Turn on the camera.  
G Press the power button (C/B) on the front to turn on the burner. The power lamp lights in green.  
H Connect the provided USB cable to the USB connector of the camera.  
NOTES:  
Insert a disc after [INSERT DISC] is displayed on the camera.  
Be sure to use the provided USB cable to connect the burner and the camera.  
When using a camera, make sure the power is provided with the AC adapter, not the battery.  
Do not subject the camera or burner to vibration or mechanical shock while writing to a disc. Be especially careful if the camera is placed  
on the burner during writing.  
Refer to “Dubbing Video Files To DVD Discs” in the manual for writing discs.  
The DVD discs that are written with this unit cannot be played with some DVD recorders/players. In that case, use [PLAY DVD] of the  
camera to playback discs.  
Connecting to PC  
A Connect the AC adapter to the burner.  
B Connect the power cord to the AC adapter.  
Power Cord  
C Connect the power cord to an AC outlet.  
D Press the power button (C/B) on the front to turn on the burner.  
The power lamp lights in green.  
E Turn on the PC.  
AC Adapter  
(provided for the burner)  
F Connect the burner to the PC with the USB cable.  
NOTE:  
To connect the burner to a PC, use the USB cable provided with the camera.  
USB Cable  
(provided for the camera)  
EN 5  
 
Writing Software — CyberLink Power2Go 5.5 Lite —  
Power2Go 5.5 Lite is software for writing video, image, audio, and  
other data files to data DVDs.  
5. Enter the user information and  
then click [Next].  
System Requirements  
The following shows the system requirements for installation.  
®
®
Operating  
system  
Windows XP Home Edition [XP] (pre-installed) or  
Windows XP Professional [XP] (pre-installed)  
®
®
®
®
Intel Pentium III, at least 800 MHz  
CPU  
Follow the on-screen instructions.  
(Intel Pentium 4, at least 2 GHz recommended)  
6. Installation starts.  
Free hard disk At least 50 MB for installation  
space  
At least 5 GB recommended for making DVDs  
7. The screen on the right appears  
RAM  
At least 128 MB (at least 256 MB recommended)  
USB 2.0/1.1* connector  
when the installation is complete.  
Connector  
Display  
Select the desired checkbox and  
then click [Finish].  
Must be capable of displaying 800 x 600 dots  
* If you use USB1.1 cable, it will take approximately 3 hours to write.  
If you select [No, I will restart  
my computer later.], the setup  
complete screen in step 8.  
appears.  
Installation Procedure  
1. Insert the installation CD-ROM in the CD-ROM drive.  
8. Click [Finish].  
2. The language selection screen  
appears.  
3. The installation start screen  
appears.  
Click [Next].  
The installation is now finished.  
NOTES:  
The above procedure is just a brief explanation on installing the  
software. For details on operating Power2Go 5.5 Lite, refer to the  
User’s guide, Help, and ReadMe installed at the same time as the  
software. You can view the User’s guide, Help, and ReadMe from  
the start menu of the PC.  
4. Confirm the contents and then  
click [Yes].  
This product does not apply to write files into CD-R or CD-RW.  
Also, it is not responded to all the functions of Power2Go 5.5 Lite.  
To get customer support and to register the software, you need  
the following product key (CD-Key):  
PXNVM-NWE4G-XQD9Q-CU9DX-3FQFN-NAKUS  
Power2Go 5.5 Lite does not support conversion of audio files to  
MP3 format.  
When the [Enter Activation Key] screen appears while using  
Power2Go 5.5 Lite, close the screen without entering the  
activation key.  
CyberLink Power2Go 5.5 Lite Contact Information  
For information on CyberLink Power2Go 5.5 Lite or other products, use the following contact information.  
Telephone/fax support  
Location  
Language  
Office hours (Mon. to Fri.)  
Phone #  
Fax #  
Germany  
English / German / French /  
Spanish / Italian / Dutch  
9:00 am to 5:00 pm  
+49-700-462-92375  
+49-241-70525-25  
Taiwan  
Mandarin  
9:00 am to 6:00 pm  
+886-2-8667-1298  
ext. 333  
+886-2-8667-1300  
Paid voice support  
Location  
Language  
Lines are open (Mon. to Fri.)  
URL  
U.S.A.  
English  
1:00 pm to 10:00 pm CST  
new_site/voice_support.jsp  
Support web/e-mail  
Language  
URL/e-mail address  
English  
German / French / Spanish / Italian  
6 EN  
 
Troubleshooting  
If you think there is a malfunction, first check the following items. If you are still unable to solve the problem, consult your local JVC dealer.  
Trouble  
Cause/Action  
Make sure the AC adapter is connected properly.  
Cannot turn the power on.  
The camera/PC is not recognized.  
The burner or AC adapter is hot.  
Make sure the USB cable is connected properly.  
This is not a malfunction. If the burner is abnormally hot, remove the AC adapter and consult the  
dealer from which you purchased the burner.  
Cannot open the disc tray.  
A disc cannot be ejected by pressing the eject button if data is being written to the disc. Wait until  
writing finishes.  
If a disc cannot be ejected with the eject button because of a failure or a malfunction caused by,  
for example, the burner being dropped, use the force eject hole to eject the disc. (See below.)  
Writing fails.  
Make sure an appropriate disc is being used. (A pg. 3, 8)  
Use discs recommended for the burner. (A pg. 8)  
Insert the disc with the label facing up.  
Make sure the writing surface of the disc is not damaged.  
Make sure the disc tray is not dirty.  
Writing to irregularly shaped discs such as heart-shaped discs or octagonal discs is not possible.  
Check the writing speed of the disc being used.  
Reading fails.  
Insert the disc with the label facing up.  
Make sure the writing surface of the disc is not damaged.  
Writing to irregularly shaped discs such as heart-shaped discs or octagonal discs is not possible.  
Any CD recorded using the packet-write method cannot be played.  
Any CD that does not comply with standards such as the CD-DA standard (copy-control CDs)  
cannot be played.  
Writing/reading at maximum speed Reading at maximum speed may not be possible if a non-standard disc is used.  
is not possible.  
Use discs recommended for the burner. (A pg. 8)  
Commercial DVDs cannot be played Check the region code. (A pg. 3)  
when the burner is connected to PC.  
It is impossible to dub the DVD discs, Connect the burner to the camera, playback using [PLAY DVD] function of the camera, and dub  
which were written with this burner,  
with DVD recorder with HDD.  
the DVD discs with the DVD recorder.  
(Refer to “Connecting to a TV, VCR or DVD Recorder” or “Using a DVD Burner for Dubbing” in the  
camera’s manual.)  
Force Eject Hole  
If a disc cannot be ejected with the eject button because of a malfunction, use this hole to eject the disc.  
Procedure  
A Turn off the burner and disconnect the USB cable and AC adapter.  
B Insert a thin rod of about 10 cm long into the force eject hole  
located on the left side of the burner. The disc tray will be ejected  
for about 10 mm.  
C Pull out the disc tray manually and take out the disc.  
NOTE:  
Be sure to place the burner horizontally.  
Force eject hole  
Copyrights and Trademarks  
Copyrights  
Duplicating copyright protected material, for other than personal use, without the permission of the copyright holder is prohibited by  
copyright law.  
Registered Trademarks and Trademarks  
®
Windows is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.  
Other company and product names mentioned herein are registered trademarks and/or trademarks of their respective holders.  
EN 7  
 
Specifications  
For general  
Power supply  
DC 12 V  
Power consumption (during data transfer)  
Dimensions of main unit (W x H x D)  
Weight of main unit  
Operating temperature  
Operating humidity  
Approx. 5.2 W/1.4 A  
171 x 56 x 262 mm (6-3/4" x 2-1/5" x 10-3/10")  
Approx. 1.4 kg (3.1 lbs)  
0 °C to 40 °C (32 °F to 104 °F)  
35 % to 80 %  
Storage temperature  
–20 °C to 50 °C (–4 °F to 122 °F)  
653 to 663 nm  
1.0 mW  
770 to 810 nm  
0.4 mW  
Wavelength  
Output  
Wavelength  
Output  
For DVD  
Laser Power  
For CD  
When connected to the camera  
Interface  
Supported discs  
High Speed USB 2.0  
DVD-R, DVD-RW  
Everio  
High definition Everio  
DVD video (motion picture only)  
Data DVD (motion picture, still picture)  
Recording format  
Everio  
(for each 4.7 GB disc)  
High definition Everio  
Approx. 30 minutes (approx. 90 minutes of video recorded in fine mode)  
Recording time  
Interface cable  
Refer to the instruction manual for the high definition Everio.  
Provided USB cable  
When connected to a PC  
Interface  
High Speed USB 2.0  
DVD-R  
Maximum 8x  
Writing  
DVD-RW  
DVD-R DL  
DVD-R  
Maximum 4x  
Maximum 4x  
Maximum 12x  
Writing speed  
(for USB 2.0)  
DVD-RW  
DVD-R DL  
DVD-ROM  
CD-R/RW/ROM  
Writing  
Maximum 12x  
Maximum 8x  
Maximum 5x  
Maximum 10x  
Reading  
DVD-R, DVD-R DL, DVD-RW  
DVD-ROM, DVD-VIDEO, DVD-R, DVD-R DL, DVD-RW  
CD-ROM, CD-DA, CD Extra, Video-CD, Mixed-CD, CD-R, CD-RW  
DVD  
CD  
Supported disc  
Reading  
Reading  
®
Supported operating systems  
Interface cable  
Windows XP Home Edition/Professional (pre-installed)  
USB cable provided with the camera  
Provided for the camera CyberLink PowerProducer 3 NE/PowerCinema NE for Everio (Authoring)  
Supported software  
Provided for the burner  
CyberLink Power2Go 5.5 Lite (data writing)  
Recommended discs  
DVD-R  
DVD-R DL  
DVD-RW  
JVC, TDK, Verbatim, SONY  
JVC, Verbatim  
JVC  
Interface cable  
Mini USB type A and type B, USB 1.1 and 2.0 compliant  
AC adapter (AP-V400U)  
Power requirement AC 110 V to 240 Vd, 50 Hz/60 Hz  
Output  
DC 12 V  
, 4 A  
NOTES:  
Only 12 cm discs can be used with this burner.  
DVD-R DL discs can be used when the burner is connected to a high definition Everio or a PC.  
A double-layer DVD-RW disc cannot be used.  
Optimal performance of the burner may not be possible depending on the disc used. Using discs of manufacturers for which compatibility  
has been confirmed is recommended.  
The appearance and specifications of the product may change without notice.  
Any CD recorded using the packet-write method cannot be played.  
Operation is not guaranteed for any CD not compliant with the CD-DA standard (copy control CD).  
When connected to the PC, it may not be possible to read the audio files depending on the music CDs (CD-DA). In this case, make use of  
applications such as Windows Media Player.  
8 EN  
 
© 2007 Victor Company of Japan, Limited  
Printed in China  
0107MNH-SW-BJ  
 

Intel Computer Hardware IE8014 User Manual
IOGear Switch GUB211 User Manual
ION Photo Scanner FILM 2 PC User Manual
Jenn Air Automobile Parts AR140 User Manual
Jenn Air Microwave Oven JMC2127 User Manual
John Lewis Freezer JLUCFZW6002 User Manual
JVC DVD VCR Combo HR XVC24S User Manual
Kenwood Stereo Amplifier KAC PS810D User Manual
Kingston Technology Switch KNE16TP RS User Manual
KitchenAid Refrigerator 2318581 User Manual