JVC Digital Camera 1SM321404 User Manual

ENGLISH  
ESPAÑOL  
FRANÇAIS  
PORTUGUÊS  
中文  
HD MEMORY CAMERA  
U
GC-FM1  
Basic User Guide  
For more details on the operations, refer  
to the “Detailed User Guidein the internal  
memory. (p. 4)  
1SM321404  
 
FCC WARNING  
(For owners in the U.S.A.)  
Changes or modifications not approved by JVC could  
void the user’s authority to operate the equipment.  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation.  
If this equipment does cause harmful interference to  
radio or television reception, which can be determined  
by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or  
more of the following measures: Reorient or relocate  
the receiving antenna. Increase the separation between  
the equipment and receiver. Connect the equipment  
into an outlet on a circuit different from that to which  
the receiver is connected. Consult the dealer or an  
experienced radio/TV technician for help.  
(For owners in the U.S.A.)  
This equipment may generate or use  
radio frequency energy. Changes or  
modifications to this equipment may  
cause harmful interference unless the  
modifications are expressly approved  
in the instruction manual. The user  
could lose the authority to operate this  
equipment if an unauthorized change  
or modification is made.  
(For owners in the U.S.A.)  
The supplied interface cable must be  
used with the equipment in order to  
comply with the limits for a digital  
device pursuant to Subpart B of Part 15  
of FCC Rules.  
Use an HDMI cable with the HDMI logo.  
 
3
Accessories  
Viewing the “Detailed  
USB Cable  
Preparation:  
(WUU102SCP001)  
Charge the camcorder. (p. 8)  
Turn on the computer.  
Press the < button for more than  
AV Cable  
C1osnecnoencdt tthoetcuarnmoconrtdheerctoamacorder.  
computer.  
(WPU122SCP001)  
Hand Strap  
To Computer  
Application software  
The supplied software is pre-  
installed in the camcorder.  
Refer to the “Detailed User Guide”  
on the right column for installing  
software.  
<Button  
USB Cable  
USB Connector  
 
4
User Guide” in the internal memory  
For Windows user  
! The “FMCAM_FRMwindow appears.  
# Select [MediaBrowser LE Install and User Guide].  
$ Select [Detailed User Guide].  
% Click a language.  
For Mac user  
! Double-click [FMCAM_FRM] on the desktop.  
# Double-click [FM1_guide].  
$ Double-click [FM1_start.pdf].  
% Click a language.  
 
5
Names of Components  
Focus Switching Lever  
Normal Recording [M]  
LCD Monitor  
Charge Lamp  
Status (Warning) Lamp  
Macro Recording [  
]
Power Button [<]  
Recording Select Button  
Power Lamp  
!
Video [  
Still Image [  
]
#
]
%
Select Button [  
Recording/Playback  
]
7
]
Index Button [  
Reset Hole  
$
Delete Button [  
]
If the camcorder malfunctions,  
push into the reset hole with a  
pointed object such as a wire to  
initialize the camcorder.  
Hand Strap  
Attachment Area  
¡ ¢ £ ¤  
Recording Start/Stop Button  
Shutter Button  
Set Button  
,
,
,
Buttons  
Zoom Buttons  
Volume Buttons  
 
6
Inserting an SD Card  
Lens  
Operations are confirmed on the  
following SDHC cards (class 4 or higher)  
with capacity 4 GB to 32 GB. Panasonic,  
TOSHIBA, SanDisk, ATP.  
Microphone  
AV Connector  
HDMI Connector  
USB Connector  
SD Slot Cover  
Speaker  
Tripod Mounting  
Socket  
To conserve power, the camcorder turns off  
automatically if there is no operation for 3 minutes.  
 
7
Charging  
Charge the battery connecting to PC with the USB cable.  
1
Press the < button to turn off  
the camcorder.  
The power lamp goes out.  
To Computer  
Charge Lamp  
2
Connect the camcorder to a  
computer.  
< Button  
Power Lamp  
turns on: Charging  
goes out: Charging finished  
Charge lamp  
USB Cable  
Charging time approx. 180 minutes  
USB Connector  
NOTE  
Charging is not possible while the camcorder is turned on.  
Make sure that the computer is turned on during charging.  
 
8
Setting Date and Time  
Preparation:  
Turn on the power and select the recording mode.  
1
2
3
4
5
$
While pressing the button,  
press the button.  
7
Select [Time setup], and then  
press the set button.  
Set the date and time by selecting items with  
¡ ¢  
,
£ ¤  
and setting values with  
,
.
After completing the setting,  
press the set button.  
Select [Exit] to quit the screen.  
NOTE  
When you first turn on the power after purchasing the camcorder, the [Time  
setup] screen appears.  
 
9
Video Recording/Playback  
Preparation:  
During recording, the screen  
display changes to red  
! #  
!
Press the  
/
button to select  
mode.  
1Video Recording  
Press the set button to start recording.  
Press it again to stop the recording.  
1Video Playback  
%
!
: Video mode  
Press the button to select the playback  
mode.  
2
3
¡ ¢ £ ¤  
Press the  
,
,
,
buttons to select a video.  
Press the set button to start playback.  
Press it again to stop the playback. To return to the  
7
index screen, press the  
button.  
 
10  
Still Image Recording/Playback  
Preparation:  
! #  
#
Press the  
/
button to select  
mode.  
1Still Image Recording  
Press the set button to take a still image.  
#
: Still image mode  
1Still Image Playback  
%
Press the button to select the playback mode.  
2
3
¡ ¢ £ ¤  
Press the  
,
,
,
buttons to select a still image.  
Press the set button.  
To delete a video or still Image  
! While a video or still image is selected, playing back or displayed, press the  
$
button.  
£ ¤  
# Press the  
,
buttons to select [Yes], and then press the set button.  
 
11  
Viewing Files on TV  
Saving Files on a Computer  
1
Connect the camcorder to a TV. Preparation:  
Charge the camcorder before saving.  
2
3
Select the external input mode  
on the TV.  
Turn on the camcorder.  
1
Connect the camcorder to a  
computer.  
Play back the video or still  
image. (p. 10, 11)  
Windows Double-click [FMCAM_SD]/  
[FMCAM_INT] in [My  
To TV  
Computer].  
Macintosh Double-click [NO_NAME]  
AV Cable  
on the desktop.  
AV Connector  
2
Copy the video or still image  
files from the “DCIM” folder.  
NOTE  
Also refer to instruction manual of the  
TV.  
 
12  

Init TV Video Accessories NT C3025 User Manual
IRIS Indoor Furnishings E4PINSR User Manual
Jasco Digital Camera 98656 User Manual
JL Audio Portable Speaker JLTR400CXi User Manual
John Lewis Refrigerator JLFSBK2001 User Manual
JVC CRT Television 0303 NIC JMT User Manual
JVC Speaker 0909WMKMDWJMM User Manual
Karcher Pressure Washer K 226 M User Manual
Keating Of Chicago Fryer 14 BB Gas User Manual
Kenmore Charcoal Grill C 172 30424 User Manual