Jabra Headphones BIZ 2400 USB User Manual

Jabra BIZ 2400 USB  
USer manUal  
 
© 2009 GN Netcom A/S. All Rights Reserved.  
This user guide is published by GN Netcom A/S.  
Thank you  
TM  
Thank you for purchasing the Jabra BIZ 2400 USB headset. We hope you enjoy it! This instruction manual will get  
you started and ready to make the most of your headset.  
The information in this user guide is furnished for informational use only, is subject to change without notice,  
and should not be construed as a commitment by GN Netcom A/S. GN Netcom A/S assumes no responsibility  
or liability for any errors or inaccuracies that may appear in this user guide.  
abouT your Jabra bIZ 2400 uSb hEaDSET  
Headset  
1
Microphone  
2a Right speaker  
2b Left speaker  
3
Headband  
3
2b  
2a  
4
1
4
5
6
7
8
9
USB Headset  
USB plug  
Clothing clip  
Mute button  
Soft button (×)  
Soft button (O)  
9
5
7
10 Hookswitch  
11 Volume control  
6
10  
8
11  
2
3
 
how To connEcT hEaDSET To Pc  
how To aDJuST volumE on ThE hEaDSET  
Plug the headset directly into a free USB port on your PC. Once connected, the headset's active mute and hooks-  
witch buttons will be illuminated.  
Use the wheel at the center of the USB  
controller to adjust the volume. Turn  
clockwise to turn up and counterclock-  
wise to turn down. You will hear a soft  
click in the headset each time you adjust  
the volume.  
The first time connected, your PC displays a small pop-up message in the task bar to indicate that a new device  
has been found. You are now ready to use the headset.  
When you reach maximum volume, the  
headset will beep twice as a warning.  
We recommend that you do not use the  
headset at full volume.  
how To muTE ThE hEaDSET  
It is possible to mute the microphone on the headset so that no sound/voice will be transmitted from the head-  
set to the PC.  
By tapping the mute button the microphone is now muted. The light will go from solid green to pulsating red.  
It will continue to pulsate red while muted.  
how To wEar ThE hEaDSET  
1
Adjust the headband length.  
To un-mute tap  
the mute button  
again and the  
The headband is adjustable in length. Push or pull the top section of the band until the headset fits comfort-  
ably.  
light will go from  
2. Wear the headset.  
Green when not muted  
pulsating red to  
Position one speaker over each ear with the band going over the top of your head, just as with a traditional  
pair of headphones.  
solid green.  
3. Position the microphone.  
Adjust the microphone by rotating it around the headset and flexing the boom arm until it is positioned less  
than 2 cm (3/4") from your mouth. (The boom is free to rotate 360° or more.)  
Red when muted  
how To anSwEr a call from your Pc SofTPhonE  
When a softphone call arrives, you will hear a ring tone in the headset. If you are using a Jabra-supported soft-  
phone*, then answer by tapping on the hook-switch button on the USB controller; tap again to hang up when  
you are done. Softphone control requires that you install Jabra PC Suite (described later in this manual)**.  
For other softphones, use the native interface on your computer to answer and hang up.  
2 cm  
3/4"  
1
2
3.1  
3.2  
When you are using a supported softphone, the USB controller lights work as indicated to the right.  
You also have the  
Solid green while idle  
option of rejecting an  
incoming call by pressing  
and holding the assigned  
Flashing green/  
Soft button. The incoming  
blue on incoming  
call will then be rejected.  
call  
Red while on a call  
Office Communicator version of the Jabra BIZ 2400 USB headset.  
4
**) If using Microsoft Office Communicator you do not need to install Jabra PC Suite.  
5
 
Jabra Pc SuITE ProgramS  
After installing the software, you will have an All Programs > Jabra > Jabra PC Suite folder in your Windows  
Start menu. It provides links to the following programs:  
how To acTIvaTE oPTIonal fEaTurES  
how To uSE ThE SofT buTTonS.  
The USB controller includes two soft buttons, labeled × and O, respectively. You are able to program the headset  
to use these two buttons for any of several functions. For example, you can configure one of the soft buttons to  
control the Bluetooth connection to a mobile phone  
-
-
-
Jabra Control Center  
Enables you to configure your headset from your PC.  
Jabra Device Firmware Updater  
Enables you to update the headset firmware.  
Jabra Devices Service  
Runs in the background and monitors your USB ports for Jabra devices. It makes sure that Windows will recog-  
nize these devices and enables the Jabra Control Center and Softphone drivers to interact with them.  
In addition to the above programs, the PC Suite also provides drivers for several types of softphones, including  
Skype, Cisco IP Communicator and others. Support for Microsoft Office Communicator is also available if you are  
using the Office Communicator version of the headset.  
When you are using a supported softphone, you will be able to control that softphone using the buttons of the  
headset USB controller. You can also talk using any softphone using its native graphic interface on your computer.  
See the section about using Jabra PC Suite, below, for details.  
Note: Jabra is constantly evaluating the softphone market to see which new programs should be sup-  
news on softphone driver development.  
how To InSTall anD uSE ThE Jabra Pc SuITE  
The Jabra PC Suite is a collection of programs that support and expand your headset’s features. It is available as a  
uSIng Jabra conTrol cEnTEr wITh ThE Jabra bIZ 2400 hEaDSET  
Jabra PC Suite enables you to:  
Jabra Control Center is the Jabra Control Suite program that enables you to configure your headset. To run the  
program, click on the Windows Start menu and select All Programs > Jabra > Jabra PC Suite > Jabra Control  
Center.  
-
-
-
-
Control several types of softphone programs from your headset via dedicated softphone drivers.  
Assign function to the programmable × and O buttons of the USB controller.  
Set the hearing-protection level for the headset.  
Update the firmware for headset.  
InSTallIng ThE Jabra Pc SuITE  
To install the Jabra PC Suite, do the following:  
1. If you have not already installed your softphone, then we highly recommend that you do so before you install  
Jabra PC Suite. This will ensure that Jabra support is correctly added to your softphone program. If you add  
a new softphone program to your computer after installing Jabra PC Suite, then we recommend that you  
reinstall Jabra, which is quite easy.  
3. Run the setup.exe program included with the download. This will install Jabra PC Suite on your computer.  
4. Follow the instructions on your computer screen. Installation is very simple and should take just a minute or  
so. Please note the following as you work through the installation wizard:  
-
-
-
Jabra PC Suite requires Microsoft .NET Runtime 3.5. If this is not already installed on your PC, then the setup  
program will automatically download and help you install it (requires an Internet connection).  
The wizard will ask which components of the Jabra PC Suite you would like to install. Usually, you should  
install all of them.  
When the headset is connected to your computer, you will see the settings that are relevant for that headset.  
These settings are divided into three tabs: Softbuttons, Settings, and Mobile (only when activated).  
Each of these is described below.  
If you are using Microsoft Windows Vista, you may see a “user account controlmessage; just click on “Allowto  
continue with the installation.  
-
-
If you are using a 64-bit PC, the firmware cannot be updated. Please updated on a 32-bit PC.  
The wizard will ask if you would like to start the Jabra Device Service when Windows starts (see also the de-  
scriptions of these programs below). If you will often use your headset with a softphone, then we recommend  
that you enable the Device Service.  
-
At one point, you may see a warning from Windows that the software "has not passed Windows Logo testing.”  
This is expected and does not indicate a problem. You can safely click on the “Continue Anywaybutton.  
6
7
 
The Settings Tab  
WARNING: Do not remove the headset from your PC while the firmware is being updated and make  
sure your computer will not shut down or go into sleep or standby mode during the process (Should  
a disconnection unintentionally occur, please retry from step 1). Ensure the headset is connected  
directly to a USB port on the PC.  
The options on the Settings tab enable you to control the Audio protection (Intellitone).  
To apply a firmware update:  
1. If you have not already done so, then attach your headset to your computer.  
2. If you have not already done so, then download the firmware update from Jabra and save it on your hard disk  
or network in a location where you can see it from your computer.  
3. On your PC, use the Start menu to run the firmware-update application of the Jabra PC Suite.  
4. Follow the instructions on your screen to identify your headset model, select the firmware update file and  
apply it. See also the Jabra PC Suite online help for more details.  
Use the settings in the Audio protection (Intellitone) area of the Settings tab to set the hearing-protection  
level of your headset.  
how To uSE ThE hEaDSET wITh a mobIlE PhonE  
Hearing risk is evaluated as a function of both volume and duration. Therefore, the maximum sound level should  
be lowered as the number of hours you spend using the headset increases. The headsets offer a choice of four  
protection levels. These features protect your hearing by preventing acoustic shocks and limiting the maximum  
noise exposure from the headset during your workday. This system is called Intellitone™, which is only available  
from Jabra. All protection levels (including “none”) also feature Peakstop™, which offers protection against sud-  
den, loud audio spikes.  
The USB controller on the headset includes a Bluetooth circuit, which gives you up to 10m range between the  
headset and a mobile phone. The Bluetooth capability enables the headset to connect directly wirelessly to a  
mobile phone or another Bluetooth sound source. When connected to a mobile phone, you will be able to  
answer and end calls using the buttons of the of the Jabra BIZ 2400 USB controller.  
All three Intellitone levels above (other than “none”) meet and exceed de facto global protection levels, and are  
compliant with NIOSH standards and EU health and safety codes of 85 dB(A).  
Pairing the Headset with Your Mobile Phone  
To use your headset with a mobile phone, you must pair the headset with your phone. Once they are paired, the  
headset will automatically connect to the mobile phone whenever it is in range. You should only need to pair the  
two devices once, and then the headset will automatically connect when it is within approximately 10m of the  
mobile phone. The headset must remain connected to your computer, because it requires power from the USB  
connection.  
In the Audio protection (Intellitone) area, mark the radio button for the Intellitone level that matches the number  
of hours in which you use the headset each day.  
If you are using a Microsoft Office Communicator softphone you need to switch to MS Office Communicator in  
the Settings tab as the primary target softphone for your calls.  
To pair your headset with a mobile phone:  
Important: Check your local laws or regulations to find out whether a specific protection level is  
mandated in your area.  
1. Connect your headset to your computer and run the Jabra Control Center (see above).  
2. Go to the Softbuttons tab of the Jabra Control Center. Here you see two drop-down lists for assigning  
functions to each of the soft buttons of the headset controller.  
The Softbuttons Tab  
The settings on the Softbuttons tab enable you to assign functions to the soft buttons of the USB controller  
(labeled × and O, respectively).  
3. Decide which of the two soft buttons you would like to use to control your mobile phone. Open the matching  
drop-down list and select Mobile from the list.  
4. The USB controller on the headset now lights blue, which indicates that the headset is in pairing mode. This  
means that it is advertising itself for pairing with other Bluetooth devices.  
Use the drop-down lists here to select from the available functions for each of the two soft buttons. Once config-  
ured, you will be able to trigger these functions by pressing the corresponding button on the USB controller.  
5. Make sure that Bluetooth is active on your mobile phone and put your phone into Bluetooth finding mode.  
The exact procedure for doing this varies by mobile phone manufacturer and model—see your mobile phone  
manual for details.  
Often, you will configure these buttons to control the Bluetooth connection to your mobile phone. *See “Pairing  
the Headset with Your Mobile Phone, below, for details about how to do this.  
6. Your phone now looks to see if any nearby Bluetooth devices are advertising themselves for pairing—this  
should include your headset. Use your phone’s controls to identify and select the “Jabra BIZ 2400device.  
Your phone may also ask for the headset’s pass code. The pass code for all Jabra devices is 0000 (four zeros); if  
necessary, enter this code into your phone and commit the code (e.g., by pressing on an OK button).  
If you want stereo sound for playing music, your phone needs to support A2DP.  
Updating the Headset Firmware  
Firmware updates can sometimes improve the performance of your headset and/or add new features. Visit the  
Jabra web site to find out if firmware updates are available for any of your Jabra products. You will be able to  
download the updates from there as they become available.  
7. Your phone will now attempt to connect to the Jabra BIZ 2400 USB controller and then shows you the result  
of the attempt. If the attempt fails, please try again. If you are still having trouble, please check your mobile  
phone documentation and/or contact technical support for Jabra and/or your mobile phone.  
8
*check you mobile manual for instruction on how to pair to headsets.  
9
 
nEED morE hElP?  
European customer service information:  
Phone:  
Belgique/Belgium  
Danmark  
Deutschland  
España  
+49 (0)8031 2651 72  
+45 45 75 99 99  
+49 (0)8031 2651 72  
+34 916 398 064  
France  
+33 (0) 130 589 075  
+39 025 832 8253  
+49 (0)8031 2651 72  
+49 (0)8031 2651 72  
+47 32 22 74 70  
Once you have selected the mobile as one of the functions for your softbuttons, a Mobile tab will appear in the  
Italia  
Jabra Control Center.  
Luxembourg  
Nederland  
Norge  
You will be able to clear your paring list, thereby deleting the mobile phones paired to the headset. Once you  
have clicked Clear pairing list – the headset will automatically enter a pairing mode.  
By clicking on Enter pairing mode, the headset will enter pairing mode and you are now able to pair the headset  
to a mobile phone – see the section on pairing your headset to a mobile phone, above.  
Österreich  
Poland  
+49 (0)8031 2651 72  
0-801-800-550; +48 12 254-40-15  
849 566 07151  
Russia  
Answering an Incoming Mobile Call  
Suomi  
+358 9 396 811  
When a call arrives at your mobile phone, you will hear a ring tone in the headset and the USB controller will flash  
blue and green. To answer the call, tap the soft button that you assigned to the mobile phone. When you are  
done talking, tap the same button again to hang up.  
Sverige  
+46 (0)8 693 09 00  
01784 220172  
United Kingdom  
USA and Canada warranty  
E-mail: Technical support: [email protected] Information: [email protected]  
Placing a Call over Your Mobile  
To place a call with your mobile phone while using your headset, simply dial your mobile phone as usual. Usually,  
the audio will be sent to your headset automatically whenever it is in range of your mobile phone.  
Phone:  
Canada  
USA  
1-800-489-4199  
1-800-826-46561  
Please see your mobile phone manual for details about how your specific mobile phone interacts with a Blue-  
tooth headset and which, if any, configuration settings are available for this feature.  
Asia Pacific customer contact information  
Phone:  
TroublEShooTIng & faQS  
Q: I have pairing problems?  
A: Make sure that the headset is in paring mode, indicated by a solid blue light. See the instructions in the user  
manual of that particular mobile to make sure that the mobile is also in paring mode.  
Australia  
China  
1-800-083-140  
+86-21-5836 5067  
Hong Kong  
India  
800-968-265 (Toll free)  
000-800-852-1185 (Toll free)  
001-803-852-7664  
Q: I cannot hear anything in my headset?  
A: Make sure that the headset is selected as audio device on both the computer in the Control Panel and in the  
application you are using. Or please check that you have not muted the phone or PC.  
Indonesia  
Japan  
+81-3-5297-7976  
Malaysia  
New Zealand  
Philippines  
Singapore  
Taiwan  
1800-812-160 (Toll free)  
0800-447-982 (Toll free)  
1800-765-8068 (Toll free)  
800-860-0019 (Toll free)  
0080-186-3013 (Toll free)  
Q: My computer does not detect the headset?  
A: Try to insert the headset in another USB port.  
Q: The computer does not automatically assign the headset as the default audio device?  
A: You can always select the headset as your default audio device manually.  
-
-
Go to the Control Panel on your computer  
Open the menu Sound and Audio devices. When inserted you can select the headset (It should appear as  
BIZ 2400) as your default device for Sound playback and Recording.  
-
Press Apply and then press OK.  
If you are using Macintosh – Go to System preferences on your computer. When inserted you can select the  
headset in the Sound menu under Output and Input.  
Q: Cannot get the headset into paring mode using a Mac?  
A: If you are using a Mac, the mute and volume functions will work. The mobile connectivity is not operational  
with a Mac.  
10  
11  
 
cErTIfIcaTIon anD SafETy aPProvalS  
CE  
gloSSary  
Bluetooth  
This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC). Hereby, GN, declares  
that this product is in compliance with the essential requirements and other relevant provisions of Directive  
A radio technology that connects devices, such as mobile phones and headsets, without wires or cords over a  
Pairing  
FCC  
Creates a unique and encrypted link between two Bluetooth devices and enables them to communicate with  
each other. Bluetooth devices will not communicate if they have not been paired.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
Jabra PC Suite  
A GN Netcom software communication control center.  
Users are not permitted to make changes or modify the device in any way. Changes or modifications not ex-  
pressly approved by Jabra will void the user’s authority to operate the equipment.  
DFU  
Device Firmware Update  
Firmware  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
The software that is embedded in a hardware device, for example the Jabra BIZ 2400 USB headset. Like software,  
firmware is a computer program, which is executed by a computer.  
IP telephony  
(Voice over Internet Protocol) The routing of internet voice conversations or through other IP-based networks.  
-
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Industry Canada  
Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This  
device must accept any interference, including interference that may cause undesired operation of the device.  
The term “IC:before the certification/registration number only signifies that registration was performed based  
on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not  
imply that Industry Canada approved the equipment.  
Bluetooth  
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Jabra is  
under license. Other trademarks and trade names are those of their respective owners.  
Dispose of the product according to local standards and regulations.  
12  
13  
 

Ingersoll Rand Grinder 7980 User Manual
Ingersoll Rand Universal Remote TP0423S5XXXXXXXX User Manual
Insignia MP3 Docking Station NS IPSD1 User Manual
Jenn Air Oven JJW3430 User Manual
Jensen Car Stereo System MP6612i User Manual
John Lewis Dishwasher JLDWW 905 User Manual
JVC Staple Gun HR J633U User Manual
KitchenAid Appliance Trim Kit kgrs206xss3 User Manual
KitchenAid Range W10190622A User Manual
Kobe Range Hoods Ventilation Hood CX1836GS User Manual