AM/FM ALARM CLOCK RADIO WITH USB CHARGER
MODEL JCR-260
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE
OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
WARNING
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG
WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The Caution Marking is located at the bottom of apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wider or the third
prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
2
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. This apparatus shall not be exposed to dripping or splashing water and that
no object filled with liquids such as vases shall be placed on the apparatus.
16. Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from the
mains completely, the mains plug should be disconnected form the mains
socket outlet completely.
17. Battery shall not be exposed to excessive heat such as sunshine, fire or the
like.
18. The marking information is located at the bottom of apparatus.
19. Remark:
protective earth provided.
20. CAUTION
this is CLASS II apparatus with double insulation, and no
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF AC PLUG TO WIDE SLOT. FULLY INSERT.
3
COMPLIANCE WITH FCC REGULATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PROTECT YOUR FURNITURE!!
This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving
when you operate the controls. These ‘feet’ are made from non-migrating rubber
material specially formulated to avoid leaving any marks or stains on your furniture.
However certain types of oil based furniture polishes, wood preservatives, or cleaning
sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on
the furniture.
To prevent any damage to your furniture we strongly recommend that you purchase
small self-adhesive felt pads, available at hardware stores and home improvement
centers everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you
place the product on fine wooden furniture.
IMPORTANT NOTES
Avoid installing the unit in locations described below:
Places exposed to direct sunlight or close to heat radiating appliances such as
electric heaters.
Dusty, humid or moist places.
Places subject to constant vibration.
4
POWER SOURCE
This unit is designed to operate on 120V ~ 60Hz AC house current. Operating this unit
on any other power source may cause damage to the unit, and such damage is not
covered by your warranty.
It is also equipped with a battery back-up system for the clock that is powered by an
optional 9V 006P battery (type 6F22 or equivalent) – not included.
BATTERY BACK – UP SYSTEM
The Battery Back-up System ensures the clock and alarm settings will be retained during a
power interruption or power outage (in order to preserve the battery life the Display will not
light). All clock settings will be kept in memory, however, the clock time may require
adjustment for exact accuracy once the power returns. If a battery is not installed, the
Display will blink “12:00” when the power is restored. This will indicate that you have to
reset the time and alarm settings.
BATTERY INSTALLATION
Note: For optimum performance an alkaline-type battery is recommended.
1. Open the battery compartment door on the bottom of the cabinet then connect one
DC 9V battery to the Battery Clip located inside.
Note: The battery clip only fits one way to ensure the correct polarity.
2. Replace the Battery Compartment Door.
IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may
damage the unit.
BATTERY CARE
i. If the unit is not to be used for an extended period of time, remove the battery. Old
or leaking battery can cause damage to the unit and will void the warranty.
ii. Do not try to recharge batteries not intended to be recharged; they can overheat,
rupture and leak. (Follow battery manufacturer’s directions.
iii. Do not dispose of batteries in fire, batteries may leak or explode.
POWER FAILURE INDICATOR
If there is no battery installed in the unit or the battery installed is weak or dead, the time
and alarm settings will be lost if the power is interrupted. When the AC power is restored
the display will flash “12:00”. This indicates that the time displayed is incorrect and
needs to be reset.
IMPORTANT:
After you reset the time, be sure to reset your alarm settings as well.
5
LOCATION OF CONTROLS AND INDICATORS
1. CLOCK/ALARM TIME SLOW SET
BUTTON
2. CLOCK/ALARM TIME FAST SET
BUTTON
11. SNOOZE BUTTON
12. DIAL POINTER
3. ALARM OFF BUTTON
4. AM/FM BAND SELECTOR
5. ALARM 1/2 SELECTOR
6. FUNCTION SELECTOR
(ON/OFF/AUTO/ALARM
7. VOLUME CONTROL/
BEEP ALARM SWITCH
8. ALARM SET BUTTON
9. TIME SET BUTTON
10. SLEEP BUTTON
13. LED DISPLAY
14. TUNING KNOB
15. SPEAKER
16. AUX IN Jack
17. USB CHARGING PORT
18. FM WIRE ANTENNA
19. AC POWER CORD
1. ALARM 1 INDICATOR
2. ALARM 2 INDICATOR
3. PM INDICATOR
6
SETTING THE CLOCK
When you connect the radio to an AC outlet for the first time the clock display will begin
flashing "12:00". The flashing will stop when you set the time.
1. Press and hold the TIME SET button and then press the FAST button to set the
coarse time.
2. Press and hold the TIME SET button and then press the SLOW button to set the
correct Hour/Minute.
NOTE
There is a PM INDICATOR located in the bottom right-hand corner of the clock display.
Be sure to observe the PM indicator when setting the time to make sure the time is set
correctly for AM or PM. If the PM indicator is 'On', the time displayed is "PM". If the PM
indicator is 'Off, the time displayed is "AM ".
LISTENING TO THE RADIO
1. Set the AM/FM BAND SELECTOR to the desired band, AM or FM.
2. Slide the FUNCTION SELECTOR to the “ON” position.
3. Select your desired station with the TUNING knob.
4. Adjust the VOLUME knob to the desired listening level.
5. When you have finished listening, slide the FUNCTION SELECTOR to the “OFF”
position to turn the radio off.
TIPS FOR BEST RADIO RECEPTION
AM - The AM antenna is built inside the radio. If AM reception is weak, slightly rotate the
unit or change the position of the unit until the internal antenna picks up the
strongest signal.
FM - If FM reception is weak, fully extend the wire antenna and vary the position and
location of the antenna until you find the strongest signal.
CHARGING YOUR SMART PHONE
This unit provides a standard USB port to charge the rechargeable battery of
your smart phone if your smart phone comes with a charging cable with a
standard USB plug.
1. Simple connect your smart phone via the charging cable included in your
phone, plug the USB plug of the cable into USB port locates on rear of the
unit. The battery charging will start immediately.
2. Unplug the cable if your smart phone has been fully charged.
Note: Because of large variety of smart phones and different circuitry, not
every smart phone can be charged in this way. Refer to your
smart phone user manual before you charge them in this way.
AUX IN OPERATION
7
This unit features an AUX IN jack for connecting your iPod, MP3 player or other digital
music player.
1. Connect the headphone jack of your external device to the AUX IN jack located on
the back of the JCR-260 (cable not included).
2. Turn the JCR-260 on and it will enter the AUX function mode once an external
device is plugged into the AUX IN jack.
3. Start playing your iPod, MP3 player or other external audio device.
4. Slowly adjust both volume controls on the JCR-260 and the external device.
5. Turn off your iPod, MP3 player etc. when finish listening. Turn the JCR-260 off and
unplug the AUX IN jack.
Remark: Once the AUX IN jack is plugged during POWER ON mode, it will
automatically enter the AUX mode no matter what position the AM/FM Band Selector is
in. Remember to disconnect the cable from JCR-260 after use in order to be able to
listen to the radio again.
ALARM OPERATION
SETTING THE WAKE UP TIME
1. Press and hold the ALARM SET button and then press the FAST button to set the
coarse wake up time.
2. Press and hold the ALARM button and repeatedly press the SLOW button to set the
correct wake up Hour/Minute.
NOTE
1. There is a PM INDICATOR located in the bottom right-hand corner of the clock
display. Be sure to observe the PM indicator when setting the alarm to make sure
the alarm time is set correctly for AM or PM. If the PM indicator is 'On', the alarm
time will be "PM". If not, the alarm time will be "AM".
2. If you plan to set dual alarms, later alarm will not sound if former alarm still
sounding. Therefore, please make sure there is sufficient time internal
between two alarms. For example, more than one hour.
CHECKING THE WAKE UP TIME
Whenever you want to check the wake up time, simply press the ALARM SET button
after select ALARM 1 or 2. The display will change from current time to wake up time.
Release the ALARM SET button to return to current time.
WAKE TO RADIO
1. Slide the FUNCTION SELECTOR to “ON” position, select the band, station, and
adjust the volume to a level that you wish to hear when the wake up time is reached,
then slide the FUNCTION SELECTOR to the “AUTO” position. The selected alarm
indicator will light on the display.
2. Reconfirm the wake up time setting by pressing the ALARM SET button.
3. At the selected wake up time the radio will turn 'On' and will play for about one hour
and then shut off automatically.
4. To stop the radio before it shuts off, press the ALARM OFF button. The radio will
stop but the alarm remains set and will turn the radio on again at the same time on
the following day.
8
5. If you do not want the radio to turn on the following day, set the FUNCTION
SELECTOR to the “OFF” position. The alarm indicator will go off.
WAKE TO ALARM
1. Rotate the VOLUME control knob until you hear a “Click” sound to turn on BEEP
ALARM switch. Set the ALARM SELECTOR to ALARM 1, ALARM 2 or ALARM 1+2
position. The related alarm indicator will light up to confirm that the corresponding
alarm is set.
2. Slide the FUNCTION SELECTOR to the “AUTO” position
3. At the selected wake up time the alarm will beep and continue for about one hour
and then shut off automatically.
4. If you want to listen to the radio after the wake up time, adjust the VOLUME knob to
switch off beep alarm & turn up the volume level. Adjust the TUNING knob for the
radio program if required.
5. To stop the beep alarm immediately, press the ALARM OFF button once. The beep
will stop but the alarm remains set and will turn on the alarm on again at the same
time the following day.
6. If you do not want the alarm to turn on the following day, set the FUNCTION
SELECTOR to the “OFF” position. The alarm indicator will go off.
SNOOZE ALARM
After the radio or beeping sounds, you may press the SNOOZE button for a few more
minutes sleep. The alarm will stop for approximately 7 minutes and then turn on again.
SLEEP OPERATION
SLEEP TO MUSIC
You can program the sleep timer to play the radio for up to 59 minutes and then shut off
automatically.
1. Slide the FUNCTION SELECTOR to “ON”, select the band, station, and volume
level that you want to listen then slide the FUNCTION SELECTOR to either the
“OFF” or “AUTO” position.
2. Press the SLEEP button, the display will show 0:59 sleep time. At the same time
radio will come on and stay on for 59 minutes.
3. To shorten the ‘SLEEP’ time to less than “0:59”, press and hold the SLEEP button
and then press the SLOW button until the desired “SLEEP” time between “0:59” and
“0:01” is shown on display.
4. To set at the maximum sleep time of 0:59, press the Sleep button. The display will
show “0:59” sleep time and the radio will begin to play. After 59 minutes, the radio
will shut off automatically.
5. After the preset “SLEEP” time has elapsed, the radio will switch off automatically. To
switch the radio off before the preset “SLEEP” time has elapsed, press the
SNOOZE button.
SLEEP AND WAKE TO MUSIC
9
1. Slide the FUNCTION SELECTOR to “ON” position and select the band, station, and
volume level that you wish to hear when the alarm comes 'On', then slide the
FUNCTION SELECTOR to the “AUTO” position. The alarm INDICATOR will light up.
2. Follow steps 2 to 4 in “SLEEP TO MUSIC” section above to set your desired sleep
time.
3. The unit is now programmed to turn off automatically at the Sleep Time you
selected and then to turn on at the preset “Alarm Time”.
4. To cancel the sleep timer before it counts down to "00" and shut the radio off, press
the SNOOZE button.
IMPORTANT:
Remember that the station and volume settings you choose for the SLEEP TO MUSIC
operation are the same settings you will hear if you set the alarm for wake to “MUSIC”
the following morning.
CARE AND MAINTENANCE
1. If the cabinet becomes dusty, wipe the exterior with a soft dust cloth only. Never use
dusting sprays or polishes on the cabinet.
2. If the cabinet becomes dirty or smudged with fingerprints it may be wiped with a soft
cloth that has been slightly dampened with a mild soap and water solution. Never
use abrasive cleansers or chemical solvents.
3. Always disconnect the power cord from the AC outlet before cleaning. Never allow
any liquid to get inside the cabinet.
4. Should any solid object or liquid fall into the unit, unplug the unit and have it checked
by qualified personnel before operating it any further.
NOTE
If there is no battery in the back-up battery compartment, the Time and Alarm settings
will be lost when the AC power cord is disconnected for cleaning. Reset the clock and
wake up time after reconnecting the AC power cord.
SPECIFICATION
Frequency Range:
AM 530 – 1710 kHz
FM 88 – 108 MHz
AC Power Source:
Backup Battery:
120V~ 60Hz
1 x 9V 006P type 6F22 battery (not included)
At Spectra, environmental and social responsibility is a core value of our
business. We are dedicated to continuous implementation of responsible
initiatives with an aim to
conserve and maintain the environment through responsible recycling.
initiatives or to find a recycler in your area.
90 DAY LIMITED WARRANTY AND SERVICE
10
VALID IN THE U.S.A ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective
materials or factory workmanship for a period of 90 days from the date of original customer
purchase and provided the product is utilized within the U.S.A. This warranty is not assignable or
transferable. Our obligation under this warranty is the repair or replacement of the defective unit
or any part thereof, except batteries, when it is returned to the SPECTRA Service Department,
accompanied by proof of the date of original consumer purchase, such as a duplicate copy of a
sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty service.
If the product is repaired or replaced under warranty, the return charges will be at SPECTRA’s
expense. There are no other express warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the
descriptions and warnings covered within the user manual or non-SPECTRA approved
modifications.
c. Claims are made within the warranty period.
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in
compliance with electrical codes or SPECTRA user manual specifications, or failure to provide
reasonable care and necessary maintenance as outlined in the user manual.
3. Warranty of all SPECTRA products applies to residential use only and is void when products
are used in a nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the unit
carefully and send it freight prepaid to SPECTRA at the address shown below. IF THE UNIT IS
RETURNED WITHIN THE WARRANTY PERIOD shown above, please include a proof of
purchase (dated cash register receipt) so that we may establish your eligibility for warranty service
and repair of the unit without cost. Also include a note with a description explaining how the unit is
defective. A customer service representative may need to contact you regarding the status of your
repair, so please include your name, address, phone number and email address to expedite the
process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $12.00 to cover
the cost of repair, handling and return postage. All out of warranty returns must be sent prepaid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at
the model you have may be discontinued, and SPECTRA reserves the right to offer alternative
options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL60634, USA.
1-800-777-5331
To register your product, visit the link on the website below to enter your information.
11
|