DOCKING DIGITAL MUSIC SYSTEM FOR iPod®
OWNER'S MANUAL
JiMS-190
(iPod® Not Included)
PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING
THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE
TABLE OF CONTENTS
DEAR JENSEN® CUSTOMER
2
IMPORTANT SAFETY INSTRUCTIONS
COMPLIANCE WITH FCC REGULATIONS
PRODUCT FEATURES
INSTALLATION
LOCATION OF CONTROLS
RADIO OPERATIONS
iPod® DOCKING
AUXILIARY INPUT
CLOCK AND CALENDAR SETTINGS
ALARM OPERATIONS
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
SPECIFICATIONS
2
3
4
4
5-6
7
8
9
10
11
12
13
14
14
SERVICE
"Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
DEAR JENSEN CUSTOMER
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical
enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.
This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get
the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and
clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So what
sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
Start your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.After all, we want
you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage
from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries
Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise.
Customer's Record:
The serial number of this product is found on its bottom cover. You should note the serial number of this unit
in the space provided as a permanent record of your purchase to aid in identification in the event of theft of
loss.
Model Number: JiMS-190
Serial Number:
IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed and manufactured to ensure your personal
safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety
and operating instructions carefully before installation and use, and keep these instructions handy for future
reference. Take special note of all warnings listed in these instructions and on the unit.
1.Water and Moisture
The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a set basement.
2.Ventilation
The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block the ventilation
openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet,
which may impede the flow of air through the ventilation openings.
3.Heat
The unit should be situated away from heat sources such as radiators, heat registers, stoves or other
appliances (including amplifiers) that produce heat.
4.Power Source
The unit should be connected to a power supply only of the type described in the operating instructions
or as marked on the appliance.
5.Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them. It is always best to have a clear area from where the cord exits the unit to
where it is plugged into an AC outlet.
6.Cleaning
The unit should be cleaned only as recommended. See the section “Care and Maintenance” of this
manual for cleaning instructions.
2
IMPORTANT SAFETY INSTRUCTIONS
7.Object and Liquid Entry
Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents
located on the product.
8.Attachments
Do not use attachments no recommended by the product manufacturer.
9.Lightning and Power Surge Protection
Unplug the unit from the wall outlet and disconnect the periods of time. This will prevent damage to the
product due to lightning and power-line surges.
10.Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in
a risk of fire of electric shock.
11.Damage Requiring Service
This unit should be serviced by qualified service personnel when:
A.The power supply cord or plug has been damaged.
B.Objects have fallen into or liquid has been spilled into the enclosure.
C.The unit has been exposed to rain.
D.The unit has been dropped or the enclosure damaged.
E.The unit exhibits a marked change in performance or does not operate normally.
12.Antenna
Do not connect an external antenna to the unit (other than that provided).
13.Periods of Nonuse
If the unit is to be left unused for an extended period of time, such as a month or longer, the power cord
should be unplugged from the unit to prevent damage or corrosion.
14.Servicing
The user should not attempt to service the unit beyond those methods described in the user's operating
instructions. Service methods not covered in the operating instructions should be referred to qualified
service personnel.
COMPLIANCE WITH FCC REGULATIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
In accordance with FCC requirements, changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
CAUTION:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
3
PRODUCT FEATURES
JiMS-190 is an iPod® Docking Music System which incorporates the following features:
- iPod®, iPod® mini, iPod classic, iPod touch and iPod nano Player / Recharger
- Audio Line-in for Connecting CD Player or Other Digital Audio Player
- 2 Built-in High Fidelity Aluminum Cone Speakers
- Multi-function Blue Back-lit LCD Display
- AM/FM Stereo Receiver with 10AM + 10FM Presets, Digital Tuning andAuto Search Function
- Electronic Volume Control
- Wake to Radio, Alarm or iPod®
- Snooze and Sleep Functions
- Built-in Contractible Aux Cord with 3.5mm Aux Plug
- External FM Antenna Jack for Better FM Reception
- Card Size Remote Control for Radio and iPod® Functions
- Output: 2 X 3W RMS
INSTALLATION
Clock Back-up Batteries Installation
1.Open the battery compartment door located at the bottom of the unit.
2.Install two DC1.5V 'AAA' (UM-4) batteries (not included) in the battery compartment following the polarity
markings shown on it.
3.Replace the battery door on the battery compartment.
NOTE:Please disconnect the main power from the unit before replacing the clock back-up batteries.
WARNING:
- Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
- Only batteries of the same or equivalent type as recommend are to be used.
- If the unit is not to be used for an extended period of time, remove the battery.
- Do not dispose of batteries in fire, batteries may explode or leak.
FM Antenna Installation
The FM Antenna Wire is provided in the package. Please see the illustration below for FM Antenna Wire
installation.
Connect the FM Antenna Wire to the antenna terminal at the rear of the main unit
Remote Control
The remote control operates on one CR2032 battery (included). To activate the remote control, remove
the insulation tab inserted in the battery compartment.
AC-DC Adaptor Connection
An AC-DC Adaptor with the output DC10V 1400mA (included) is required for operating the main unit.
1.Firmly insert the DC plug of the adaptor (included) into the DC Jack on the back of the unit
2.Plug the adaptor's AC plug into your household AC power outlet (120VAC/60Hz).
NOTE: This unit is not magnetically shielded and may cause color distortion on the screen of some
TVs or video monitors. To avoid this, you may need to move the unit further away from the TV or monitor
if unnatural color shifts or image distortion occurs.
4
LOCATION OF CONTROLS
Main Unit
Top view
Bottom view
21
22
1
2
12
7
9
6
11 5 10
4
3
8
Front view
Rear view
16
20
19 18
17
15
13 14
15
1.iPod® Dock
2.iPod® Docking Connector
3.POWER On/Off Button
4.VOLUME +/- Buttons
5.SNOOZE/LIGHT Button
6.TUN +/- /iPod
Forward/Backward Buttons
To turn the unit on or off
Adjust the volume level up or down
Activate the snooze function; Turn the LCD backlight on or off
Buttons
Tune the radio channel frequency up or down; iPod® Skip/Search
for Backward,
for Forward.
7.CH +/- Buttons
8.ALARM On/Off Button
Select the preset radio stations
Switch the alarm on or off
9.SLEEP Button
10.MODE Button
11.MEM/iPod
12.FUNCTION Button
mode
Select the time duration of the sleep timer
Enter the setting mode
Button
Save the radio preset stations; save settings; iPod® PLAY/PAUSE
Select AM/FM Radio, iPod® mode and AUX (auxiliary input)
13.LCD Display
14.Remote Infra-red Sensor
15.Pair of Speakers
16.AUX in Jack
17.Cord Retracting Wheel
An Audio Cable with a 3.5mm stereo plug for the connection of external audio device
For extending or retracting the auxiliary cord
18.DC Jack
To connect to external DC power supply
19.Headphone Jack
20.FM Antenna Terminal
21.Battery Compartment
It is to contain two 'AAA' batteries for clock back-up
22.RESET Button
For resetting the unit
5
LOCATION OF CONTROLS
Remote Control
1
1.Infra-red Transmitter
2.POWER On/Off Button
3.VOL +/- Button
4.FUNCTION Button
6
7
2
3
5.ALARM On/Off Button
6.SNOOZE/LIGHT Button
7.TUN Up/Down Buttons
RECORD
8
CH
9
10
for Down,
8.CH +/- Buttons
9.MEM Button
for Up
4
11
13
12
5
10.MODE Button
11.SLEEP Button
12.iPod® Skip/Search Forward/Backward Buttons
12
for Backward,
13.iPod® PLAY/PAUSE
14.Battery Compartment
for Forward.
14
6
RADIO OPERATIONS
FM Antenna
Connect the detachable FM Antenna Wire to the FM Antenna Terminal as instructed in the section
“INSTALLATION”. Fully extend the FM Antenna Wire for the maximum reception.
Radio Tuning
1.Press the POWER button to turn on the unit.
2.Press the FUNCTION button repeatedly until “AM” or “FM” mode is reached.
3.In FM radio mode, if necessary, press the MODE button to select STEREO (ST) or MONO FM reception.
4.To manually tune the radio station, repeatedly press the TUN Up/Down Buttons.
5.To automatically search the next or previous station with the strongest signal, press and hold the TUN
Up/Down Buttons until the frequency readout on the display begins to scan and then release the button.
The tuner will stop scanning until the strongest signal station is searched.
NOTE:
-Use manual tuning to select weaker stations that might be bypassed during automatic tuning.
-If the automatic search does not stop at the exact frequency, for example, it stops at 100.9MHz
instead of 100.8MHz, press TUN +/- to finely tune the exact frequency.
Preset Stations
The unit allows you to store up to 10 AM and 10 FM stations in the preset memories for easy recalling any
time.
1.Press the POWER button to turn on the unit.
2.To activate the radio, press the FUNCTION button to select AM or FM band.
3.Tune to your desire radio station by pressing the TUN +/- buttons.
4.Press the MEM button. The preset channel number “01” and the icon “MEM” will flash on the display.
5.Select your desired preset number by pressing CH +/- button.
6.After the preset channel number is selected, press the MEM button to confirm your selection. The station
is saved in the preset channel now.
7.To further store more stations, repeat the steps 3, 4, 5 and 6.
Radio Broadcast System Selection
In case the unit is moved to other countries with slightly different radio broadcast system, the unit allows
you to select USA, EU and Japan systems.
1.Set the unit to Power Off mode.
2.Press the MODE button repeatedly until the flashing “USA”, “EU” or “JP” is seen.
3.Press the TUN +/- button to select one of the broadcasting systems, 9kHz or 10kHz as the tuning step.
4.Press MEM button to save the setting and exit the setting mode.
NOTE:
The followings are the specifications of the three radio broadcast systems:
- USA's Radio Broadcast System
AM 520
FM 87.5
1710 kHz, 10 kHz tuning step
108 MHz, 0.1 MHz tuning step
- EU's Radio Broadcast System
AM 522
FM 87.5
1620 kHz, 9 kHz tuning step
108 MHz, 0.05 MHz tuning step
- Japan's Radio Broadcast System
AM 522
FM 76.0
1629 kHz, 9 kHz tuning step
108 MHz , 0.1 MHz tuning step
Tips for the Best Reception
To obtain the bestAM reception, slightly rotate the unit until the clearest signal is received or place it near
outdoor.
To obtain the best FM reception, fully extend the FM Antenna and adjust its direction.
NOTE: The iPodmay cause interferenceto the AM reception ifit is dockedand turned ON.
You shouldturn off the iPod manuallyor remove itfrom the unitfor better reception.
7
iPod® DOCKING
If the docking port will not be used for an extended period of time, it is recommended to cover the docking
port by using the “Dock Cover” insert (included).
1.Use the iPod adaptor included in your iPod and insert it into the docking area. Your iPod can now be
inserted into the docking port by placing the connector on the bottom of the iPod onto the connector in
the docking bay.
Note: Please be careful when seating the iPod into the docking to avoid damaging
the 30-pin connector on iPod or docking system.
2.Press the POWER On/Off button to switch on the docking system.
3.Press the FUNCTION button repeatedly until the indicator “iPod” shows on the display. The iPod® will
start playing and charging automatically.
4.Select your desired EQ and play mode in your iPod®.
5.Press the VOL +/- button on the docking system to adjust your desired volume level
NOTE:The volume level cannot be adjusted by the volume control of your iPod® after being docked.
6.The iPod® is charging even during playback.
NOTE: The iPod will only charge in iPod, AUX, or power "OFF" modes.
7.To remove the iPod® from the unit, press and hold the PLAY/PAUSE button for three seconds to switch
off the device and then gently remove it from the docking connector.
You may control the playback of your iPod® by:
- Press the PLAY/PAUSE
- Press the iPod Skip/Search Forward
button to pause or resume the iPod® playback;
or Backward
button to skip to the next or previous song;
- Press and hold the iPod Skip/Search Forward or Backward button for fast-forwarding or
fast-rewinding during playback.
8
AUXILIARY INPUT
The auxiliary input cable and plug are built in the unit and allows users to connect their CD player, MP3
player or other digital audio players to the unit.
1.Keep turning the Cord Retracting Wheel, located at the rear of the unit, to the right and pull out the
AUX IN Cable located next to the wheel.
2.Connect the AUX IN Stereo Plug to the Line Out Jack or Headphone Jack of an external audio device
(not included).
3.Switch on the audio device.
4.Press the FUNCTION button repeatedly until AUX mode is displayed. The display will show the
icon “AUX”.
5.Control the volume level by the volume control on the audio device or pressing the VOL +/- on the main
unit or the remote control.
9
CLOCK AND CALENDAR SETTINGS
The clock and calendar can be set in Power Off mode.
Clock Setting
1.Press the MODE button 3 times, the clock starts to flash.
2.Press the TUN +/- button to set the hour.
3.Press the VOL +/- button to set the minute.
4.Press the MEM button to confirm the settings.
12/24 Hour Time Display Mode Setting
1.Press the MODE button repeatedly until the 12/24 Hour Format Setting mode is reached. The flashing
'12hr' or '24hr' will be displayed.
2.Press TUN +/- button to select 12 hour or 24 hour time display mode.
3.Press the MEM button to confirm the setting.
Calendar Setting
Year
1.Press the MODE button repeatedly until the year setting mode is reached. The year readout flashes now.
2.To set the year, press the TUN +/- button to set the correct year.
3.Press the MEM button to confirm the setting.
Month/Date
1.Press the MODE button repeatedly until the Month/Date setting mode is reached. The readout of the
Month/Date flashes now.
2.To set the month, press theTUN +/- button. To set the date, press the VOL +/- button.
3.Press the MEM button to confirm the settings.
10
ALARM OPERATIONS
Setting the Alarm Time
When the unit is in Power Off mode:
1.Press the MODE button once. The alarm clock display flashes now.
2.Press the TUN +/- button to set the alarm hour and VOL +/- button to set the alarm minute.
3.Press the MODE button again. The alarm icon will flash.
4.Select “Wake to Buzzer”, “Wake to Radio” or “Wake to iPod®” by pressing the VOL +/- button.
NOTE:
- When “Wake to Radio” is selected, ensuring that your desired radio station is tuned and the
proper volume level is set.
- When “Wake to iPod®” is selected but your iPod® has not been docked, the alarm source will be
redirected to the Buzzer automatically when the alarm time is reached.
5.Press the MEM button to save all the settings and exit the setting mode.
6.To activate the daily alarm, pressALARM On/Off button. The icon “ ” will appear on the display.
7.When the alarm time is reached, the alarm will sound from the selected source immediately.
Wake to Buzzer ( BUZ
)
- After the alarm time is reached, the buzzer alarm will sound immediately for one minute.
- After the first alarm minute, it will switch to Auto Snooze mode. Once the alarm is off, the next alarm will
come again after the 10 minute snooze period is completed. This operation will be repeated 3 times.
After the third alarm is finished, the alarm will shut off until the same alarm time on the next day.
- To stop the buzzer alarm immediately, press theALARM On/Off button once.
Wake to Radio (
RAD)
- The radio will automatically turn on when the alarm time is reached. It starts softly and becomes
gradually louder.
- The radio alarm will keep for 60 minutes and then will automatically shut off.
- To stop the radio alarm sound immediately, press the ALARM On/Off button once.
Wake to iPod® (
iPod)
- Your docked iPod® will automatically switch on when the alarm time is
reached. It starts softly and becomes gradually louder.
- The iPod® playback will keep for 60 minutes and then automatically shut off.
- To stop the iPod® playback immediately, press the ALARM On/Off button once.
Snooze Function
- When the alarm sounds, it can be temporarily stopped by pressing the SNOOZE button.
The display will show the indicator “SNOOZE”.
- The alarm will be delayed for 10 minutes and then come again.
- This manual snooze operation can be repeated only three times.
Sleep Timer
- The Sleep Timer allows you to set the unit to automatically power off after a selected sleep time
is set.
- To activate the Sleep Timer and select the sleep time, press the SLEEP button repeatedly.
The sleep times available for choosing are: 15, 30, 45 or 60 minutes. The display will show the
indicator “SLEEP”.
- To switch off the Sleep Timer, press the SLEEP button repeatedly until the SLEEP indicator
disappears.
- To switch off the unit before the selected sleep time, press the POWER On/Off button once.
- To check the current sleep time, press the SLEEP button once.
11
CARE AND MAINTENANCE
- Do not subject the unit to excessive force, shock, dust or extreme temperature.
- Do not tamper the internal components of the unit.
- Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
- Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
- Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps
or motors.
Resetting the Unit
If the unit is subject to a power surge or electric shock, it is possible that the internal micro-controller may
lock up and the unit will not respond to any commands from the top panel controls or remote control.
1.In this event, unplug and then reconnect the AC power plug into the wall outlet.
2.Use a straightened paper clip, toothpick or similar objects to press the RESET button located on the
bottom of the main unit (see the below figure). The reset operation clears the system memory and all of
your previous settings will be erased. CAUTION: DO NOT USE SHARP, POINTED OBJECT TO PRESS
THE RESET BUTTON. IT MAY DAMAGE THE RESET SWITCH INSIDE THE UNIT.
RESET button
12
TROUBLESHOOTING GUIDE
Symptom
Possible Problem
Solution
AC Adaptor is not plugged into a
wall outlet or the connector is not
plugged into the power supply jack
on the back of the unit.
Plug the AC adaptor into a wall
outlet and plug the connector into
the supply jack on the unit.
The unit does
not respond (no power)
Plug another device into the same
outlet to confirm the outlet is working.
Wall outlet is not functioning.
Using no/wrong iPod® Adaptor
Make sure the dock insert is the
proper fit for your iPod®
iPod® does not
dock properly
Remove your iPod® from the dock
and check for obstruction on the
connectors in the dock and on your
iPod®. Then reseat it in the dock.
iPod® does not installproperly.
iPod® is not installed properly.
Remove your iPod® from the dock
and check for obstruction on the
connectors in the dock and on your
iPod®. Then reseat it on the dock.
iPod® does not respond
to the speaker system
Your iPod® is locked up.
Please make sure that your iPod® is
working properly before docking into
the unit. Please refer to your iPod®
manual for details.
iPod® is not installed properly.
Remove your iPod® from the dock
and check for obstruction on the
connectors in the dock and on your
iPod®. Then reseat it in the dock.
iPod® does not
charge up
iPod® is locked up/ frozen.
iPod® battery has problem.
Please make sure your iPod® is
working properly before docking into
the unit. Please refer to your iPod®
manual for details.
Select iPod, AUX or Standby mode
for iPod charging
Unit is in Radio mode
iPod unintentionally
wake up in PAUSE
mode
It may be caused during function
switching
Wait for 3 minutes, iPod will enter
sleep mode automatically
The reception at the set location is
poor.
Slightly rotate the unit for the best
reception.
AM band is too noisy
Volume level is set too high.
Decrease the volume.
If the iPod original sound source is of
poor quality, distortion and noise are
easily noticed with high-power
speakers. Try a different audio source
such as a music CD.
Sound is distorted
Sound source is distorted.
If you are using an external sound
source like older generation of iPod®,
try reducing the output volume on the
device itself. Also try turning bass
boost OFF or change the EQ setting.
Unit gets warm after
extended play at
high volume
This is normal.
Turn the unit off for a period of time or
lower volume.
13
SPECIFICATIONS
Power Supply
Power Adaptor (included)
Input: AC120V/60Hz
Output: DC10V/1400mA
Battery Back-up for Clock
Remote Control
DC1.5V 'AAA' (UM-4) Battery X 2 (not included)
CR2032 X 1 (included)
Frequency Range
USA's Radio Broadcast System
AM 520
FM 87.5
1710 kHz, 10 kHz tuning step
108 MHz, 0.1 MHz tuning step
EU's Radio Broadcast System
AM 522
FM 87.5
1620 kHz, 9 kHz tuning step
108 MHz, 0.05 MHz tuning step
Japan's Radio Broadcast System
AM 522
FM 76.0
1629 kHz, 9 kHz tuning step
108 MHz , 0.1 MHz tuning step
SERVICE
Please refer to the instructions on the enclosed warranty card for returning your unit for service. When
returning the unit, please remove batteries to prevent damage to the unit in transit and/or from possible
leakage. We are not responsible for batteries returned with the product or for the cost of replacement.
Distributed by:
SPECTRA Merchandising International, Inc.
Chicago Industry Tech Park
4230 North Normandy Avenue
Chicago, IL 60634, U.S.A.
Please have model number ready, for Customer Service, call 1-800-777-5331.
*The specification and external appearance of the set are subject to change without prior notice.*
Printed in China
14
|