1
Installation:
DV1628
Owner's Manual
Getting Started.
It is a good idea to read all of the instructions before you begin the
installation.
Tools and supplies needed:
•
•
•
•
•
•
•
•
Flat and Phillips screwdrivers
Wire cutters and strippers
Tools to remove existing radio
Electrical tape
Crimping tool
Volt meter/ Test light
Crimp connections
Speaker Requirements: Only connect speakers rated in the load
impedance range of 4 Ohms. Speakers with a load impedance less
than 4 Ohms could damage the unit
Thank you!
Thank you for choosing a JENSEN product. We ve tried to make the
instructions in this owner s manual clear and easy to follow. If you take a few
minutes to look through it, you ll learn how to use all of the features of your
new JENSEN AM/FM/CD/DVD player for maximum enjoyment.
1. Prepare:
Disconnect battery. Before you begin always disconnect the
battery s negative terminal
•
Installation...........................................................................................1
Troubleshooting..................................................................................3
Operation.............................................................................................4
Specifications......................................................................................16
Warranty.............................................................................................17
2. Mounting angle:
Do not exceed a 30¡ mounting angle. Improper operation of the
•
unit could occur if the mounting angle is exceeded.
3 0
3. Removal of factory radio or DV1628:
1
3
Troubleshooting:
ERROR
DISPLAY
CORRECTIVE
ACTION
Check power
connection with
Multi-meter. Check
fuse for continuity
with Multi-meter.
PROBLEM CAUSE
CDP and CDC
Does not
operate,
display does
not light.
No power to
Yellow wire,
No power to
Red
ERR1 appears
on display
ERR6 appears
on display
Mechanism
Error
Press Reset button.
Press Reset button.
Sled Error
Inline fuse
blown
Replace fuse.
No power to
unit
Inline fuse
blown
Check and/or
replace fuse.
Check speaker
wires, connect
harness.
CDP ONLY
Speaker
harness not
connected
Power wire
shorting to
ground
ERR2 appears
on display
No Audio to
speakers
Servo Error
Press Reset button.
Check disc - disc
may be dirty or
upside down. If not
press the reset
button.
Make sure wire is
not pinched.
ERR7 appears
on display
TOC reading
error
Blows fuses
Speaker
wires shorting
to ground
Make sure wire is
not pinched.
Incorrect
fuse/ rating
too small
CDC ONLY
Replace with
proper fuse.
Check disc - disc
may be dirty or
upside down. If not
press the reset
button.
Check proper
mounting angle
and/or mounting
strap for secure
mounting.
ERR2 appears
on display
TOC reading
error
Mounting
angle is too
great or not
secure.
CD/DVD skips
ERR3 appears
on display
ERR7 appears
on display
Temperature
error
Disc and
Servo error
Press Reset button.
Press Reset button.
Use CD/DVD
cleaning kit.
Dirty laser.
3
4
4. Source:
Press the source button to toggle
Operation:
between Radio, CD/DVD, CDC/DVDC, and Aux mode.
(NOTE: CDC/DVDC mode is active only if a changer is
connected. This source will be skipped if a changer is not
installed.) Press and hold the Source button for 2 seconds to
mute the rear speaker and subwoofer. Press and hold for 2
more seconds to re-activate the rear speakers and subwoofer.
1. Front Panel / Remote Control
•
Controls
27
3
29
12
26
10
11
6
15
13
2
7
5. Enter / Mute:
Press the Enter button to select the
highlighted menu bar. Press and hold the Enter button for 2
seconds to mute the speakers.
OPEN
SMART
MOODE
CLK
DSP
BAND/MENU
SEL
AS/PS
AUDIO
6.
7.
/
:
Press the
to rewind the track.
Press the to skip to the next
to fast forward the
ENT
MUTE
PWR/ILL
track. Press the
DOLBY
/
SOURCE
2
SCN
3
RPT
4
RND
5
D.DN
6
D.UP
1
track, press the to skip to the previous track.
8. Slow/Zoom:
Activate the slow forward or zoom
4
5
21
23
20
24
25
9
22
1
function.
9.
/
Pause/Play button. Press once to
pause the CD/DVD, press again to resume play.
10. Band/Menu: In radio mode, press the
LED
28
Band/Menu button to change from AM/FM bands. In
DVD mode, press the Band/Menu button to activate
the DVD menu.
11.
/AS/PS:
In DVD mode, press the /AS/PS to
stop the DVD. In Radio mode, press the /AS/PS to
access the Automatic memory storing and preset scanning
mode. Press and hold the button for 2 seconds to scan
through the 6 preset stations.
1. Power Button:
Press the Power button to turn the unit
12. Vol + / Vol -
Controls the volume level, press the
on. Press and hold for 2 seconds to turn the unit off. Press the
Power button when the unit is on to select 4 different
brightness settings for the panel.
Vol+ button to increase the volume and the Vol- button to
decrease the volume.
13. Audio/DSP:
Chooses the audio soundtrack and the
preset EQ. DVD mode: Press and hold for 2 seconds to
change the language soundtrack. Feature is activated only
if the DVD is recorded with multi language soundtracks.
CD Mode: Press and hold for 2 seconds to change from
Stereo, Mono left and Mono right mode. Press once to
2. SEL:
Selects the audio effect. Press the select
button to choose the desired Bass, Treble, or speaker setting.
Use the VOL+ and VOL- button to adjust the levels.
3. Open:
the CD/DVD slot.
Opens the front panel to allow access to
4
5
toggle between EQ settings, each press will toggle from
Flat, Classic, Pop, Rock, to off.
CLK
RPT
14. Angle:
Allows the viewer to view the DVD at
different angles if the DVD is recorded with this feature.
Press the angle button while the DVD is Stopped. Then
1
15
19
SCN
press the
levels.
15. Disp/Clock:
/
to adjust the brightness and contrast
RND
D.DN
D.UP
Press to display the Clock or Disc
information. Setting the clock: Press and hold the
Disp/Clock button until the display begins to flash. Press
the #6
/
to adjust the hours or minutes.
16. Subtitle:
Changes the subtitles language on the
29
9
10
8
DVD if the DVD is recorded with this feature.
17. Title: Displays the title that is stored on the
CD/DVD.
18. Setup:
19. 0-9:
20. M1-M6:
memory.
AS/PS
11
5
Displays the setup menu.
Numeric key buttons.
Selects the Radio stations stored in the
7
21. Scan:
Scans the entire disc and plays the first
10 seconds of each track.
6
22. Repeat:
Replays the current disc or track.
Plays the disc in random.
Chooses the CD/DVD, ( only if CDC or
23. Random:
24. Disc- / Disc+:
DVDC is connected.
25. Reset:
13
16
17
14
4
DSP
Reset button, press only if the unit is
locked up. This resets the unit to the factory settings.
2
18
26. Remote IR:
27. Display:
28. Eject:
Receiving sensor for the remote control.
Main unit display
Eject the CD or DVD
12
29. Smart Mode / Disc: Press the Smart mode button to put the
unit into Smart mode. See Smart mode function. In DVD
changer mode ( Only if DVDC is connected ) press the button
to enter the Disc Menu.
5
6
•
Front Panel removal:
2. MP3 Compatible:
a. Press the open button #3.
b. Press the middle release button and pull the panel straight
out.
This unit supports the following MP3 CD formats:
•
•
•
Joliet
Romeo
ISO9660
3. Smart Mode function:
The Smart Mode feature allows the user to listen to two different audio
sources at the same time. One source can be selected through the speaker
system while the DVD can be listened to through an external audio source.
Ex. IR transmitter for wireless headphones.
•
•
•
•
•
Smart mode is activated only in DVD mode.
Press Source button #4 to enter DVD mode.
Press Smart button #29 to activate Smart Mode
Press Smart button #29 again to deactivate Smart Mode.
When Smart Mode is active, Smart Mode will be displayed in the
top right corner of the Radio display.
Pressing the Source button #4 while in Smart mode will change the
Audio source being played on the speakers. The Smart Mode
audio to the external audio source will remain DVD.
•
Radio Removal
a. Grab the grooves of the front frame with fingers and pull.
b. Insert the supplied levers inside the grooves on the right
and left hand side of the radio. Pull the levers out as
shown.
•
1
2
3
6
7
General Setup Cont.:
Initial Setup:
TV Display:
Press the Setup #18 button to enter the Setup mode.
Selects the appropriate TV aspect ratio, 4:3 or 16:9
SETUP MENU - - MAIN PAGE
•
•
•
Normal / PS
Pan and Scan for 4:3 aspect ratio. If selected while using
a 16:9 TV, the left and right edges will be cut off.
o
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
Normal / LB
o
Letterbox style for 4:# aspect ratio. If connected to a
wide-screen TV, black bands will appear on the top and
bottom of the screen.
PREFERENCES
WIDE
o
Select when using a 16:9 formatted TV
EXIT SETUP
TV Type:
-- GENERAL PAGE --
Press the Down #7 key to highlight the desired Setup screen.
Press the Enter button to select the desired Setup screen.
TV DISPLAY
TV TYPE
MULTI
NTSC
PAL
PIC MODE
General Setup:
ANGLE MARK
OSD LANG
CAPTIONS
-- GENERAL PAGE --
TV DISPLAY
TV TYPE
NORMAL/PS
NORMAL/LB
WIDE
MAIN PAGE
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
•
•
•
Multi
o
NTSC
o
PAL
o
Automatically selects the DVD format when inserted
Select when using a DVD formatted as NTSC
Select when using a DVD formatted as PAL
MAIN PAGE
7
8
PIC Mode:
Angle Mark:
-- GENERAL PAGE --
-- GENERAL PAGE --
TV DISPLAY
TV DISPLAY
TV TYPE
TV TYPE
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
AUTO
FILM
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
ON
VIDEO
SMART
SSMART
OFF
MAIN PAGE
MAIN PAGE
•
Auto
o
PIC mode automatically selects the setting depending on
the DVD.
•
•
•
Film
Changes the viewing angle of multi-angle DVD s. If the DVD does not
have this feature, the viewing angle will not have any effect.
o
Video
o
Smart
o
Suitable for film or progressive source.
Select Video for best image resolution.
When the TV output is progressive, additional vertical
processing is applied.
•
SSmart
o
When the TV output is progressive, pixel based motion
adaptive de-interlacing is activated.
8
9
OSD Language Setup:
-- GENERAL PAGE --
Speaker Setup:
SETUP MENU - - MAIN PAGE
ENGLISH
FRENCH
GERMAN
TV DISPLAY
TV TYPE
GENERAL SETUP
SPEAKER SETUP
AUDIO SETUP
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
PREFERENCES
SPANISH
EXIT SETUP
MAIN PAGE
Selects the Language that the OSD will be displayed in.
Down Mix:
Closed Captioning:
•
•
•
LT/RT
o
STEREO
o
OFF
o
Activates Dolby Surround compatible output.
-- GENERAL PAGE --
Activate simple Stereo mode.
TV DISPLAY
TV TYPE
Turns stereo mode off to enable Downmix
PIC MODE
ANGLE MARK
OSD LANG
CAPTIONS
ON
OFF
MAIN PAGE
Turns the Closed Captioning on and off.
9
10
Speaker selection:
DOWNMIX
CENTER
DOWNMIX
CENTER
ON
REAR
REAR
OFF
15MS
9MS
SUBWOOFER
CNTR DELAY
REAR DELAY
TEST TONE
BASS
SUBWOOFER
CNTR DELAY
REAR DELAY
TEST TONE
BASS
3MS
OFF
MAIN PAGE
MAIN PAGE
Highlight the desired speaker selection then the ON / OFF
Selection to turn the desired speaker ON or OFF. Individual speaker
selection is active only in Downmix mode.
DOWNMIX
CENTER
Select Rear Delay and / or CNTR Delay to control the delay of the audio
signal to the Rear and Center speakers.
REAR
5MS
3MS
SUBWOOFER
CNTR DELAY
REAR DELAY
TEST TONE
BASS
1MS
OFF
MAIN PAGE
10
11
AUDIO SETUP:
-- DOLBY DIGITAL SETUP --
DOWNMIX
CENTER
SPDIF
OFF
ON
OP MODE
DUAL MONO
D R C
REAR
SUBWOOFER
CNTR DELAY
REAR DELAY
TEST TONE
BASS
LPCM OUTPUT
MAIN PAGE
ON
OFF
SPDIF - Turns the SPDIF optical output Off and On
MAIN PAGE
-- DOLBY DIGITAL SETUP --
SPDIF
OP MODE
DUAL MONO
D R C
LINE MODE
Test Tone: By selecting TEST TONE, the unit will send a tone to each of
the speakers in the following order:
LPCM OUTPUT
LEFT CENTER RIGHT
MAIN PAGE
LEFT SURROUND RIGHT SURROUND
OP Mode — Only one operating mode for the Dolby Digital decoder.
11
12
-- DOLBY DIGITAL SETUP --
-- DOLBY DIGITAL SETUP --
SPDIF
FULL
6 / 8
4 / 8
2 / 8
OFF
SPDIF
OP MODE
DUAL MONO
D R C
OP MODE
DUAL MONO
D R C
STEREO
CH1 MONO
CH2 MONO
MIX - MONO
LPCM OUTPUT
LPCM OUTPUT
MAIN PAGE
MAIN PAGE
DRC — Dynamic Range Control:
Select DRC to adjust the dynamic range of the Dolby Digital encoded
program.
Dual Mono:
The dual mono reproduction is for the Dolby Digital program
-- DOLBY DIGITAL SETUP --
with 1+1 Audio code mode.
•
Stereo —Reproduces 1+1 program CH1 for left channel, CH2 for
right channel
SPDIF
•
•
•
CH1 Mono —Reproduces CH1 in both left and right output.
CH2 Mono —Reproduces CH2 in both left and right output.
Mix Mono — Reproduces CH1 + CH2 in both left and right
output.
OP MODE
DUAL MONO
D R C
LPCM OUTPUT
LPCM 48K
LPCM 96K
MAIN PAGE
LPCM Output:
Sets the LPCM output sample rate.
12
13
-- PREFERENCES PAGE --
AUDIO
Language Setup screens:
SUBTITLE
ENGLISH
FRENCH
DISC MENU
LOCALE
-- PREFERENCES PAGE --
SPANISH
AUDIO
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
GERMAN
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
JAPANESE
SUBTITLE
DISC MENU
LOCALE
CHINESE
GERMAN
ITALIAN
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
Audio — Selects the language to be heard through the audio output.
Disc Menu —Selects the language to be displayed for the Disc Menu.
Subtitle —Selects the language to be displayed for the subtitles.
-- PREFERENCES PAGE --
AUDIO
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
GERMAN
SUBTITLE
DISC MENU
LOCALE
PARENTAL
PASSWORD
SMART NAV
OFF
DEFAULTS
MAIN PAGE
13
14
Setting a new password — Select change and press enter. Type in the old
password and press enter. The factory default password is 3308. Type in a
new 4 digit password.
Parental Controls:
-- PREFERENCES PAGE --
Smart NAV:
LANGUAGE
SUBTITLE
1 G
-- PREFERENCES PAGE --
2
DISC MENU
LOCALE
3 PG
LANGUAGE
SUBTITLE
DISC MENU
LOCALE
4 PG 13
5
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
6 PG - R
7 NC - 17
8 ADULT
NO_PARENTAL
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
NO MENU
WITH MENU
Allows the parents to set a certain rating of movie that may be viewed.
Highlight the Max rating desired for viewing and press enter. Movies
above this rating will not be allowed to be viewed without the proper
password.
This sets the play style for playing MP3 discs.
-- PREFERENCES PAGE --
PASSWORD:
LANGUAGE
SUBTITLE
-- PREFERENCES PAGE --
DISC MENU
LOCALE
LANGUAGE
SUBTITLE
DISC MENU
LOCALE
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
RESET
PARENTAL
PASSWORD
SMART NAV
DEFAULTS
MAIN PAGE
CHANGE
Reset —Restores the factory default settings.
14
15
Default Table:
WIDE
MULTI
AUTO
ON
TV DISPLAY
TV TYPE
PIC MODE
ANGLE MARK
GENERAL SETUP
SPEAKER SETUP
OSD LANGUAGE ENGLISH
OFF
CAPTION
DOWNMIX
OFF
SPDIF
OFF
LINE MODE
STEREO
OFF
OP MODE
DUAL MONO
DRC
AUDIO SETUP
LPCM 96K
LPCM OUTPUT
AUDIO
ENGLISH
ENGLISH
ENGLISH
SUBTITLE
DISC MENU
USA
LOCALE
PREFERENCES
PARENTAL
PASSWORD
SMART NAV
NO-PARENTAL
3308
WITH MENU
15
16
AM
GENERAL SPECIFICATIONS:
Frequency coverage
: 522 to 1620 KHz (Europe Version)
: 530 to 1710KHz (USA Version)
: 450 KHz
Power Supply Requirements : DC 12 Volts, Negative Ground
IF
Sensitivity (S/N = 20 dB) : <35 dBu
Chassis Dimensiions(mm)
: 178(W) x 160(D) x 50(H)
Tone Controls
- Bass (at 100 HZ)
- Treble (at 10 KHZ)
- SUPER BASS
: +14dB/-14dB
: +14dB/-14dB
: 3 level
Note:
Maximum Output Power
With Power amplifier
Specifications and design are subject to modification, without notice,
due to improvements in technology.
: 5x40W
LINE Output Level(DVD)
: 4V rms 0.3V
Current Drain
- With Power Amplifer
- Without Power Amplifer
: 15 Ampere (max.)
: less than 2.0A
DVD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
Video Signal
: More than 70 dB
: More than 70 dB
: 20 Hz - 20 KHz+1dB
: composite 1.0Vpp (75 W load)
RADIO
FM Frequency Range
: 87.5 to 108.0 MHz (Europe Version)
: 87.5 to 107.9 MHz (USA Version)
: 10.7 MHz
: <5 u V
: > 30 dB
Sensitivity (S/N = 30 dB)
Stereo Separation
16
17
This warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION
OF THIS WARRANTY. ANY ACTION FOR BREECH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 30 DAYS FROM THE DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREECH
OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED
WHATSOEVER. No person or representative is authorized to assume for
the Company any liability other that expressed herein in connection with the
sale of this product.
90 DAY / 12 MONTH LIMITED
WARRANTY
AUDIOVOX SPECIALIZED APPLICATIONS, LLC (the Company)
warrants to the original retail purchaser of this product that should this
product or any part thereof, under normal use and conditions, be proven
defective in material or workmanship within 90 days from the date of
original purchase, such defect(s) will be repaired or replaced (at the
Company s option) without charge for parts and repair labor. After the
initial 90 day period and for a period of 12 months from the date of the
original purchase, the Company will supply at no charge a replacement for
any defective part(s).
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages so the
above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights and you may also have other rights which vary
from state to state.
To obtain repair or replacement within the terms of this warranty, the end
user should contact the O.E.M. The product is to be delivered with proof of
warranty coverage (e.g. dated bill of sale, and serial number of the unit, and
vin#), specification of defect(s), transportation prepaid, to an approved
warranty station.
AUDIVOX SPECIALIZED APPLICATIONS, LLC.
Visit us at www.asaelectronics.com
This warranty does not extend to the elimination of externally generated
static or noise, to the correction of antenna problems, to costs incurred for
removal or reinstallation of the product, or to damage to any tapes, cd s,
dvd s, speakers, accessories, or electrical systems.
This warranty does not apply to any product or part thereof which, in the
opinion of the Company, has been damaged through alteration, improper
installation, mishandling, misuse, neglect, or accident. THE EXTENT OF
THE COMPANY S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE,
AND, IN NO EVENT, SHALL THE COMPANY S LIABILITY EXCEED
THE PURCHASE PRICE PAID BY THE PURCHASER FOR THE
PRODUCT.
17
|