JV-TV5020
USER’S MANUAL
CUSTOMER SERVICE INFORMATION
JWIN New York Office 51-41 59th Pl.,
Woodside, NY 11377 USA
1-866-807-JWIN
Toll Free Number:
E-mail:
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
V C R MODE : The Screen comes to VCR mode.
AUTO MODE : Displays each channel sequentially.
INDEX
.
20
19
PAGE
SECTION 1
FREEZE
A
B
1
5
2
6
3
7
4
1.
2.
PURPOSE OF THIS PRODUCT
SPECIFICATIONS
SECTION 2
1
2
8
Z
3.
4.
CONNECTIONS
3
5
5
6
INSTALLATION
UP
4-1. Basic System Installation
4-2. Installation with a VCR or Time Lapse Recorder
SECTION 3
LEFT
ENTER RIGHT
DOWN
MENU
MODE
5.
OPERATION
8
REMOTE CONTROL UNIT
5-1. Change Display Mode
5-2. QUAD Mode Operation
5-3. Automatic Camera Skip in the Auto Mode
5-4. Manual Mode Operation
8
10
11
11
5-5. How to Program the Menus for On-Screen-Display 11
5-6. Recording and Playback
IR REMOTE CONTROL
6-1 Function Selection Keys
6-2 Other Keys
18
6.
7.
18
19
20
Fig. 10 Remote Control
6-1. Function select keys.
TROUBLESHOOTING
20
Z
ZOOM MODE : 2X Zoom Mode
QUAD MODE : It makes you to select the Quad Mode .
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
5-6. Recording and Playback
1
SECTION 1
There are two video output ports on the rear of the splitter. One
of them is MON port which is for output of the Quadrant pictures
and sequential pictures.
1. PURPOSE OF THIS PRODUCT
The purpose of this COLOR QUAD SPLITTER is to provide an
economical, but effective method to monitor more than one area with video
cameras. This Splitter has following features to enable the users to get the
best for their money and efforts:
Read the specifications for Time Lapse Recorder or VCR
thoroughly before doing this step, because its manufacturer uses
different methods to record.
a. To record, connect a coaxial cable to the AUDIO IN and VIDEO
IN/OUT port on the rear of the monitor and connect the other
end of the coaxial cable to the VIDEO IN/OUT port on the VCR.
b. Press the “REC” button on the VCR.
z Accepts NTSC.
z NTSC : 720x480 Pixels.
z Real time quad picture display.
z PIP (Picture-In-Picture) function.
z 2x ZOOM with Vertical and Horizontal interpolation.
z Full-screen display of one camera.
z Four-position sequential switcher.
z Programmable dwell times to include cameras and the quad
display in the sequential switching mode.
z On-screen-display and programmable menus.
z User-programmed data is protected battery back up.
z Freeze capability can freeze a picture.
Program selectable border line.
c. To play, press the AUTO button of the monitor until it goes to
the VCR mode with black screen and beeping sound.
d. Press the “PLAY” button on the VCR.
e. The recorded picture will be displayed on the monitor.
When you are operating the normal VCR, make sure that the
VCR is in line or A/V mode.
6. IR REMOTE CONTROL
This color quad splitter is also operated by IR Remote Controller.
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
a. key buzzer
2. SPECIFICATIONS
17
18
[Y] – When use this button, BUZZER voice sounds.
[N] – When use this button, BUZZER is dumb.
z
z
z
z
z
z
z
System
b. loss buzzer
NTSC: 525 lines, 60 fields per second
Input Signal
[Y] – Camera connection signal becomes BUZZER sound if is
patience.
Composite video, sync. Negative
Operating Temperature
32 to 104 degree F
Humidity
[N] – If camera connection sign is patience, BUZZER is dumb.
5-5-4. PAGE 5 SPECIAL Menu
Press the MODE/MENU button again, the following menu
screen will be displayed.
0% to 90% (non-condensing)
Connectors
[ SPECIAL ]
BNC connector : video in/out
Power Source
DEFAULT LOAD
EXIT
: [Y]
DC 12V , 1.5A
Power consumption
10.5W
- PAGE4 -
Fig. 9 Page 4 Menu
a. This function is to Loading for INITIAL data.
-
-
[N] : Disable INITIAL data loading.
[Y] : Enable INITIAL date loading.
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
-
-
Place the green color character to the DWELL TIME
using the ◀ ,▶ , ▲ and the ▼ buttons, and press
SECTION 2
3
2
the ENTER button to flash the Dwell Time and set it using
the ▲ or the ▼ buttons. Press the ENTER button again
to stop flashing the Time.
3. CONNECTIONS
The following connections are located on this splitter. See Fig. 1
for connection locations. Do not plug the power supply into this
splitter until all connections are made.
Press the MODE/MENU button to return to the Page 2
INDIVIDUAL menu.
FRONT VIEW
c.
LOAD
The video signal is normally terminated by 75 ohms. But in
case the signal is distributed to a number of lines, only one of
lines is needed to be terminated by 75 ohms (1Vp-p), while
the other lines are terminated by High impedance status
(2Vp-p). The 75 ohms or the HI can be selected by pressing
the ENTER button.
Fig. 1 (CONNECTION LOCATIONS – Front View)
Note.
(1) This splitter has 2pages (is consists of page A with channel 1~4
and page B with channel 5~8).
5-5-3. Page 4 BUZZER Menu
Press the MODE/MENU button again, the following menu
screen will be displayed.
(2) All buttons have a different function by press button short or long.
(3) To go into the ZOOM or MENU or VCR mode, press the
corresponding button long.
[ BUZZER ]
KEY BUZZER
LOSS BUZZER
ALARM BUZZER
ALARM TIME
EXIT
:
:
:
:
[Y]
(4) By pressing channel button shortly, channel moves to anther
channel where is located in the same place on different page.
(5) By pressing Quad button shortly in Quad mode, the screen moves
to anther Quad mode on different page.
[Y]
OFF
OFF
(6) If you press channel button long, the screen became freeze frame.
- PAGE4 -
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
Fig. 8 Page 4 Menu
When it is set to be zero (OFF) the corresponding camera will
be skipped in the Automatic sequential switching mode.
- Buttons on the Front View
16
① POWER button is to turn the system ON or OFF.
② REMOTE is IR(Infra-red) sensor.
[ INDIVIDUAL ]
Title
Dwell
Alm
Load
③ Buttons CH1(ch5), CH2(ch6), CH3(ch7) and CH4(ch8)are to select
a channel.
CH1: C 1
03s
03s
03s
03s
OFF
OFF
OFF
OFF
75
75
75
75
CH2: C 2
CH3: C 3
CH4: C 4
④ QUAD If press button, conversion and page (Page A, Page B)
conversion in Quad screen .
QUAD A: PAGE 1 03s
EXIT
⑤ ZOOM button displays the 2x ZOOM picture in any mode.
⑥ MODE button displays the PIP or 2PIP.
⑦ MENU button is to go into the on-screen-display mode.
⑧ VCR button displays the VCR video input.
REAR VIEW
- PAGE2 -
Fig. 7 PAGE2,3 MENU
a. Camera Title
- Place the green color character to the date digit using the
◀ , ▶ , ▲ and the ▼ buttons and press the ENTER
button. The first empty box will be flashing
-
Select the position you want to enter the letter or the
numeric number using the ◀ , ▶ buttons.
▲ and the ▼ buttons is to change the new character.
Press the ENTER button to return to the Page 2
INDIVIDUAL menu.
-
-
①
②
③
④
You can enter up to 8 characters for each camera title.
Fig. 2 (CONNECTION LOCATIONS – Rear View)
- Connections on the Back View
b. Set the DWELL TIME
Dwell Time is the amount of time that a camera is displayed
on the screen when the system is in the Automatic sequential
switching mode. The Dwell Time can be adjusted individually
for each camera and the quad display from 1 to 30 seconds.
① CAMERA INPUT (channel 1 to 8) connectors are BNC’s for
composite video input/output.
② VCR IN/OUT is a BNC connector for video input/output.
③ MAIN MONITOR is video out to the monitor.
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
④ DC IN is input for DC +12V.
usage. See ‘Important Safeguards’ in this manual.
-
Install cameras to be connected to this splitter.
the DATE (MM:DD:YYYY). Change the content using the
▲ and the ▼ buttons. Press the ENTER button again to
stop flashing the DATE.
4.
INSTALLATION
5
4
4-1.
Basic System Installation
Perform following steps to install your splitter. See Fig. 3.
-
-
Use the ◀ and the ▶ buttons to shift the cursor to the
next digit.
Press ENTER button at the EXIT location to exit from this
mode, the splitter will display the quadrant pictures.
c.
There are three formats to display the date.
- MM-DD-YYYY: for U.S.A.
- YYYY-MM-DD: for Asian countries.
- DD-MM-YYYY: for European countries.
Set the TIME & TITLE Display and BOUNDARY LINE
VIDEO IN
d.
-
-
Place the cursor to the “Y”.
MONITOR
Selecting Y or N using the ENTER button will turn the
TIME & TITLE Display and BOUNDARY LINE ON or OFF.
Fig 3. INSTALLATION FOR CAMERAS
e.
Set the BLANK COLOR
-
-
Unpack all components of the splitter from the packing
-
-
Place the cursor to the “BLUE”.
material.
Selecting BLUE, GRAY or BLACK using the ENTER
button will decide the color of the blank channel.
Identify all of the following pieces:
z Color Quad Splitter
f.
Set the EXIT
z Adaptor (+12V, 1.5A)
- Place the green color character to the EXIT with the ▲
and the ▼ buttons.
z Remote control
z CCD Cameras and Camera Cables (Optional)
z User’s manual
- Press the ENTER button to exit the MENU setup mode.
5-5-2. Page 2 INDIVIDUAL Menu
The following items can be adjusted or programmed on this
-
Place the quad splitter in a convenient location for your
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
menu screen. Pressing MODE/MENU button again, the
- Place the cursor to the date digit using the ◀ , ▶ ,▲
and the ▼ buttons, and press the ENTER button to flash
following menu screen will be displayed.
5-5-1. Page 1 GENERAL Menu
-
Connect the DC power cord between this splitter and your
wall mounted power outlet.
13
The following items can be adjusted or programmed on this
menu screen.
-
-
Turn on the power of all cameras and this splitter.
A quadrant display should be seen on the monitor.
[ GENERAL ]
4-2. Installation with a VCR or Time Lapse Recorder
This splitter may be installed with a standard VCR or a Time
Lapse Recorder. Perform following steps to install the splitter
with them.
TIME
DATE
: 00:00:00
: 01/01/2002
:MM/DD/YYYY
: [Y]
DATE FORMAT
TIME DISPLAY
TITLE DISPLAY
BOUNDARY LINE
BLANK COLOR
ALARM TIME
EXIT
: [Y]
: [Y]
: [BLUE]
: OFF
: [Y]
- PAGE1 -
Fig 6. Page 1 Menu
a.
Set the TIME
- Place the cursor to the time digit using the ◀ or the▶
buttons, and press the ENTER button to flash the TIME
(HH:MM:SS) and set it using the ▲ or the ▼ buttons.
Press the ENTER button again to stop flashing the TIME.
VIDEO OUT VIDEO IN
-
Use the ◀ and the ▶ buttons to shift the cursor to the
next digit.
VCR (Rear view)
- The TIME is displayed in military form of time.
-
Press ENTER button the EXIT location to exit in this mode,
the splitter will display the quadrant pictures.
Fig. 4 INSTALLATION WITH A VCR
b.
Set the DATE
-
Connect all cameras to the splitter.
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
-
Check if you are ready with following stuffs.
z Recorder
z Two RCA to BNC video coaxial cables for Time Lapse
MODE key in MENU Mode
6
7
Recorder
[ INDIVIDUAL ]
[ GENERAL ]
: 00:00:00
z Video Tape
TIME
DATE
Title
Dwell
Alm
Load
: 01/01/2002
DATA RORMAT
TIME DISPLAY
TITLE DISPLAY
BOUNDARY LINE
BLANK COLOR
ALARM TIME
EXIT
: MM/DD/YYYY
z Two RCA to RCA video coaxial cables for consumer
recorder (if necessary)
CH1: C 1
03s
03s
03s
03s
OFF
OFF
OFF
OFF
75
75
75
75
:
:
[Y]
[Y]
CH2: C 2
CH3: C 3
CH4: C 4
QUAD A: PAGE 1 03s
EXIT
:
[Y]
:
:
[BLUE]
OFF
[Y]
-
-
-
-
Connect one video coaxial cable from the VCR OUT on
the back of the splitter to the VIDEO IN port of the VCR.
Plug the DC power cords for the splitter and the recorder
into the wall mounted power outlets.
:
- PAGE2 -
- PAGE1 -
Menu[1]
Menu[2]
Turn on the power switches for the splitter and the
recorder. A picture should be displayed on the monitor.
Program the recorder and start the recording process
using the VCR manufacturer’s instructions.
[ INDIVIDUAL ]
[ SPECIAL ]
Title
CH1: C 5
CH2: C 6
CH3: C 7
CH4: C 8
Dwell
Alm
Load
DEFAULT LOAD
EXIT
: [Y]
03s
03s
03s
03s
OFF
OFF
OFF
OFF
75
75
75
75
QUAD B: PAGE 2 03s
EXIT
- PAGE3 -
CAUTION
- PAGE5 -
Do not use staples to support the cables or wires (it might be
damaged).
Menu[5]
Menu[3]
[ BUZZER ]
All connections should be properly connected and insulated to
prevent electrical shock and fire hazards.
KEY BUZZER
:
[Y]
[Y]
OFF
OFF
LOSS BUZZER
ALARM BUZZER
ALARM TIME
EXIT
:
:
:
- PAGE4 -
Menu[4]
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
Fig 5. MENU PAGE[1], [2], [3], [4], [5]
SECTION 3
5-3. Automatic Camera Skip in the Auto Mode
12
If you do not wish to view a particular camera, set the
DWELL TIME in the MENU(2),(3) setup mode to a value of
zero.
5. OPERATION
5-1 Change Display Mode
5-4. Manual Mode Operation
There are 6 Different display mode styles as shown below. And they
are selected by the MODE key or the QUAD key or the AUTO key or
CHANNEL keys. When system is reset or power is turned on system
is initialized to the QUAD mode.
This splitter displays only one camera (full-screen), even if
there are additional cameras connected to it.
-
Press the QUAD button on the front panel of the splitter
to enter the AUTO mode from the QUAD mode. If the
splitter is currently in AUTO mode, proceed next step.
Press the desired channel button.
PAGE A
01/01/2002 00:00:00
01/01/2002 00:00:00
C 1
-
-
C 1
C 3
C 2
C 4
Press the QUAD button to return to the QUAD mode.
5-5. How to Program the Menus for OSD (On-Screen Display)
There are three pages of Menus to display the time, date, and
a camera title for each camera, etc. on the monitor. To enter
the MENU setup mode, press the MODE/MENU button on the
front panel of the monitor until the MENU displays on it (2
seconds). The page 1 GENERAL screen will be displayed with
beeping sound, and pressing MODE/MENU button one more
time will show the Page 2 INDIVIDUAL screen, then the Page
3, Page 1, Page 2, so on. Press the ENTER button the EXIT
location in Menu1 to exit the MENU setup mode.
C 2
QUAD Mode
1 Picture In Picture Mode (1PIP)
C 1
01/01/2002 00:00:00
C 1
01/01/2002 00:00:00
C 2
C3
C 2
2 Picture In Picture Mode (2PIP) Sequence Picture In Picture Mode
8-CHANNEL QUAD SPLITTER
8-CHANNEL QUAD SPLITTER
8
JV-TV5020 USER’S MANUAL
USER’S MANUAL
JV-TV5020
C 1
01/01/2002 00:00:00
AUTO key
C 1
01/01/2002 00:00:00
CHANNEL key
Any Mode
Single Mode
Auto Sequence Mode
Single Mode
The following diagram shows the sequence of selected mode when
pressing QUAD key and CHANNEL keys.
QUAD key
Auto
Sequence Mode
CHANNEL key
Sequence
PIP Mode
Single Mode
QUAD Mode
Any Mode
Sequence
PIP Mode
The following diagram shows the sequence of selected mode when
pressing MODE key.
Sequence
PIP Mode
MODE key
QUAD key
Sequence
PIP Mode
5-2.
Quad Mode Operation
1 PIP Mode
The splitter normally displays quadrant picture in the Quad
mode to the monitor when the power is first applied to it. If
the monitor is not displaying quadrant pictures, press the
QUAD button so that the unit returns to the QUAD mode.
Press the (CH1,ch5), (CH2,ch6), (CH3,ch7) and (CH4,ch8)
button to freeze the picture. Corresponding picture(s) will be
frozen with the letter “F” on the screen.
Quad Mode
Any Mode
2 PIP Mode
The following diagram shows the sequence of selected mode when
pressing AUTO key and CHANNEL keys.
8-CHANNEL QUAD SPLITTER
9
8-CHANNEL QUAD SPLITTER
10
|