MONITOR WITH DVD RECEIVER
DDX6036
DDX6036M
INSTALLATION MANUAL
© B54-4756-00 (MW/M2W)
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
9. Perform the Initial Setup. (Refer to the Instruction
Manual.)
2WARNING
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
•
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.
•
•
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
¤CAUTION
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as the
heat sink and enclosure become hot.
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
About the Front Panel
When removing the product from the box or installing
it, the front panel may be positioned at the angle
shown in (Fig. 1). This is due to the characteristics of a
mechanism the product is equipped with.
If the program that is activated when the product is
first powered on works properly, the front panel will
automatically move into the position (initial setting
angle) shown in (Fig. 2).
•
•
•
•
(Fig. 1)
(Fig. 2)
•
Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
After the Installation
After the installation, perform the <Initial Setup>
(Refer to the Instruction Manual) by referring to the
instruction manual.
|
English
3
Connection
If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire. Always
connect those wires to the power source running
through the fuse box.
¤
Ignition key
switch
ACC
A
B
Ignition wire (Red)
A
Car fuse box
Battery wire (Yellow)
Car fuse box
(Main fuse)
B
FM/AM
antenna input
Antenna Cord
Ground wire (Black) -
(To car chassis)
C
C
Battery
Connect to the vehicle's parking brake
detection switch harness.
⁄
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Reverse sensor wire (Purple/White)
Connect to vehicle's reverse lamp harness when
using the optional rear view camera.
Steering remote control input (Light Blue/Yellow)
To steering remote
To use the steering wheel remote control feature, you need to
an exclusive remote adapter (not supplied) matches your car is
required. When this terminal is not in use, leave its cap on.
⁄
Dimmer control wire (Orange/White)
Mute wire (Brown)
To car light control switch
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
⁄
Depending on what antenna you are using,
Motor antenna control wire (Blue)
Power control wire (Blue/White)
connect either to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier,
connect to its power control terminal.
If no connections are made, do not let the cable come out from the tab.
⁄
|
4
DDX6036/DDX6036M
Cooling fan
FUSE ( 15A )
Accessory 1
REVERSE
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
White/Black
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
+
+
+
+
White
Gray/Black
ILLUMI
MUTE
Gray
Green/Black
Green
Purple/Black
ANT. CONT
P.CONT
Purple
|
English
5
System Connection
USB terminal
USB device
(commercially available)
Audio input (iPod/AV Input 2 switchable)
Resistance-free stereo type mini plug (3.5φ)
Visual input (iPod/AV Input 2 switchable)
Resistance-free mini plug (3.5φ)
Accessory
2
Accessory 3
Audio/Visual Output
• Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
Audio/Visual input
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Rear View Camera Input
• Visual input (Yellow)
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
|
6
DDX6036/DDX6036M
Optional Accessory Connection
iPod
(commercially available)
KCA-iP301V
(Optional Accessory)
Visual Output (Yellow)
Audio Output (Black)
USB terminal
USB terminal
KCA-BT200
(Optional Accessory)
Connection cable
(Included in the KCA-BT200)
Navigation System
(Optional Accessory)
1
2
3
Type Switch
1 2 3
TV Tuner
(Optional Accessory)
T V A N T E N N A I U T
Connection cable
(Included in the Navigation
System)
R O U N I T
M O O T N I T
Navigation units that can be connected to this unit.
(As of December, 2009):
⁄
・ KNA-G630
・ KNA-G630CN
For latest information, access the
Connection cable
(Included in the TV tuner)
|
English
7
Installing the Escutcheon
For General Motors
For Toyota/Scion
1. Cut out accessory 5 to meet the shape of the
1. Cut out accessory 5 as illustrated.
opening of the center console.
2. Attach accessory 5 to the unit.
Cutting line
Cut out to meet the shape of
the opening in the vehicle.
Accessory 5
Accessory 5
2. Fold double-sided adhesive (accessory 6) along
the slit and attach it to accessory 5 cut-out
against the center rib as illustrated. Use 2 pieces of
accessory 6 for 1 accessory 5 cut-out.
For Volkswagen
3. Attach accessory 5 cut-out to the unit.
1. Attach accessory 9 to the unit.
Accessory 6
Accessory 9
|
8
DDX6036/DDX6036M
Installation for Monitor/Player Unit
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
⁄
Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Accessory 7 (M5x6mm)
or Accessory 8 (M5x7mm)
Car Bracket
Accessory 7 (M5x6mm)
or Accessory 8 (M5x7mm)
|
English
9
Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Insert the two removal tools 4 deeply into the
slots on each side, as shown.
1. Engage the catch pins on the removal tool 4 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Accessory 4
Accessory 4
Catch
Lock
3. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
⁄
•
The frame can be removed from the top side in the same
manner.
2. When the lower level is removed, remove the
upper two locations.
⁄
•
Be careful to avoid injury from the catch pins on the
removal tool.
4. Pull the unit all the way out with your hands, being
careful not to drop it.
|
10
DDX6036/DDX6036M
|