www.dexpres s .com
Fax on Demand (775) 8 33-36 0 0
This Data Sheet Includes Information On
KitchenAid
Product Model Number (s):
36" Retractable Downdraft Vent System:
KIRD862HSS
•
•
Backsplash
36"
33 1/2"
Kit: KPED890T
2 1/8"
•
Dimensions (Actual Size)
Vent overall depth: 2 1/8"
Vent overall width: 36"
•
1 7/8"
Vent cutout depth: 1 7/8"
Vent cutout width: 33 1/2"
Raised vent distance: 8 1/4"
Vent height below countertop: 26 1/8"
Additional Information
Cutout vent dimensions
Overall vent dimensions
Cooktop
•
•
Countertop front edge
• Electrical requirements: Voltage 115, single phase,
60Hz. AC. Ampere 15. Grounded circuit required.
Locate power supply junction box at lower right corner
of cabinet.
36"
Wall View
• KitchenAid exterior power system, Part No.
KPED890, is required to complete this system.
• Installation location should be away from strong draft
areas, such as windows doors and strong heating
vents. Before making cutout, check that vent and
cooktop location will clear cabinet walls, backsplash
and rear wall studs inside cabinet.
(not to scale)
Vent
Raised
8 1/4"
Countertop
• All openings in wall or floor where vent is to be
installed must be sealed.
• See cooktop manufacturer's installation instructions
for cooktop cutout depth and width.
Vent Intake
26 1/8"
• NOT approved for use in mobile homes.
• 36" minimum base cabinet is required. 3 1/2" depth
clearance from countertop to top of cabinet drawers (or
other obstructions in base cabinet) is required.
• Cabinet drawer may need to be removed and
permanent drawer front installed.
Vent Junction Box
• Use either 9" round (recommended) or 3 1/4" x 10"
ductwork. Maximum length of ductwork for both 9"
round and 3 1/4" x 10" is 55 feet.
Cabinet Floor
• Stainless Steel finish.
See pages 2-3 for additional information
Cooktop
2 1 / 8 "
Sid e Vie w
(not t o scale )
6 1 / 8 "
Ve nt Int ake
Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Int e rio r ho us ing
Copyright © Dimension Express, 2000.
284
• NEVER reuse Data Sheets. Data Sheets are subject to change without
notice. Dimension Express is a FREE service bureau and is updated daily,
it makes far more sense to spend the time necessary to request new Data
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
• Call Dimension Express if you have any questions at (775) 833-3633 •
• Always refer to a current Code at a Glance or manufacturer directory •
• Data Sheet codes change on the first of odd numbered months at 12:01am •
BN53 • A284B149C116 • 11751 • 001311 • 215841 • 52906
This Data Sheet Includes Information On
KitchenAid
www.dexpres s .com
•
Product Model Number (s):
•
DIMENSION EXPRESS
Page 3
36" Retractable Downdraft Vent System:
KIRD862HSS
Fax on Demand (775) 8 33-36 0 0
Kit: KPED890T
Cutout sizes when used with
KitchenAid cooktops
3/4" max. backsplash
depth.
D
1/2" min. to
backsplash or rear
wall
C
B
A
F
Required min.
countertop depth
E
OA
OA
Model #
A
B
C
E
F
D
Width Depth
KGCT365G, KGCS166G, KECT336G 35 1/4" 33 1/2" 19 5/8" 2 1/8" 1 3/4" 37 1/2" 23"
25"
KECC562*, KECC568G*, KECC567G* 35 1/2" 33 1/2" 20 1/2" 2 1/8" 2" 37 1/2" 23 1/4" 26 7/8"
KECS161G*
35" 33 1/2"
19"
2 1/2" 3 3/8" 37 5/8" 23" 25 5/8"
* Requires deeper than standard countertop and cabinet
Vent cutout locations
(not to scale)
Ce nt e rline -
Back edge of
counter cutout
Duct size: 3 1 / 4 " x 1 0 "
3/8"
1/4" Minimum from
backsplash to cutout.
C
L
2 3 9 / 1 6 "
C
L
Vent Cutout shown
assumes rear edge of
cooktop overlaps edge
of downdraft vent by 3/8"
The center line of duct cutout
location is 3/8" to the left of
cutout opening centerline.
4 1 / 8 "
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.
116
• NEVER reuse Data Sheets. Data Sheets are subject to change without
notice. Dimension Express is a FREE service bureau and is updated daily,
it makes far more sense to spend the time necessary to request new Data
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
• Call Dimension Express if you have any questions at (775) 833-3633 •
• Always refer to a current Code at a Glance or manufacturer directory •
• Data Sheet codes change on the first of odd numbered months at 12:01am •
BN53 • A284B149C116 • 11751 • 001311 • 215841 • 52906
|