Operation: Knoll volume controls are very easy to use. The VC100im
has a total of 12 different volume settings including fully off.
To increase the volume (in this room only), turn the volume control
knob clockwise. To lower the volume, turn the volume control knob
counterclockwise.
VC100im
Impedance Matching Volume Control
Installation Instructions v1.0
To set the correct amplifier or receiver volume setting we suggest that
you turn the Knoll room volume control in one room to maximum.
Adjust the amplifier or receiver volume to the loudest comfortable
setting you will use and no further or louder. In this way the Knoll
volume control has the most usable settings. If the amp volume
control was set louder, the Knoll volume control would have to be
turned down to be back at a comfortable level with less overall volume
positions available.
Warning: To be installed and/or used in accordance with appropriate
electrical codes and regulations.
Caution: Do not install these keypads in an electrical junction box
with 110V or higher unless an approved barrier separates the high and
low voltage sections.
Description: The Knoll VC100im is a twelve-position in-wall
mountable stereo speaker volume control with impedance matching
capability. From one to eight pairs of speakers can be safely driven
from one stereo amplifier using an equal number of VC100im’s.
Separate impedance matching components are not required. The Knoll
WT6 one stereo input to six stereo output connection strip is available
to neaten the wiring of larger systems.
Warranty
Knoll Systems warrants the VC100im sold in the USA and Canada by authorized
Knoll dealers to be free of defects in materials and workmanship. This warranty
extends for three full years from the date of purchase by the original consumer.
Any products returned to Knoll Systems and found to be defective by Knoll
Systems within the warranty period will be repaired or replaced at Knoll
Systems option, at no charge. Knoll Systems will not be responsible for the
actual cost of installation or removal of the product, nor for any incidental or
consequential damages. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation may not apply to
you. This warranty gives you specific legal rights. You may have additional
legal rights that vary from state-to-state.
Basic System Layout and Pre-Wiring: A stereo amplifier controls
multiple pairs of speakers. Decide where the speakers and volume
controls will be placed in the various rooms. When wiring always leave
an extra couple of feet of wire at both ends so installation of the
speakers and volume controls is quick and easy. Up to eight pairs of 8-
ohm speakers can be safely connected to one amplifier.
Specifications
Peak RMS Power Rating 100 watts per channel
Continuous RMS Power 50 watts per channel
Run a fire-rated two-conductor speaker wire (14-18 gauge wire) from
each speaker to the volume control location in each room. Next, run a
four-conductor speaker wire from the volume control to the amplifier
location. Ideally each run back to the amplifier is a home run, but
wires can be daisy chained from room to room. If you plan to daisy
chain the wiring we suggest using larger 14-gauge wire. If 2 pairs of
speakers are being controlled by 1 volume control, wire the 2 pairs in
series if they are 4 or 6-ohms and parallel if they are 8 or 16-ohms.
Our web site has information on how to wire in series and parallel.
Frequency Response
Mounting Depth
20 to 20,000 Hz
2.55" (6.5 cm)
Fits single gang
Electrical Junction Box
4-16 ohms (single or multiple
speakers)
Speaker Impedance
Connection
Detachable screw terminals
White decora style
Warning: Never attempt to make the final combined speaker
impedance less than 4-ohms as this may cause safety issues.
Color and Style
Knoll Systems
To tidy up the installation, use Knoll’s WT6 seven position wire
connection strip at the amplifier. Two or more may be required for
some installations.
145 Tyee Drive Point Roberts, WA 98281
14-7163 Vantage Way, Delta BC V4G 1N1
Tel: (604) 940-9326, fax (855) 734-3363
Made in China
|