Kodak DirectView
3MP Color Display
Model# DV3MC
CAT 802 6635
Contents
Thank you for purchasing our Color LCD Monitor.
1.Safety Precautions .................................3
2.Auxiliaries...............................................7
3.Features .................................................8
4.How to Operate ......................................9
5.Connection Method ..............................13
6.Reference.............................................16
7.Assignment of Connector Pins.............17
8.Failure Diagnosis..................................18
9.Cleaning ...............................................19
10.Specifications .......................................20
11.Technical Support .................................22
◆ Carefully read this User's Manual and use the
product properly. Before using it, also read
"Safety Precautions."
◆ Keep the User's Manual as close to you as
possible and in safe custody.
◆ If you have lost the manual, contact your dealer.
We will reissue a manual.
Safety Precautions
Attention, Consult accompanying documents
Dangerous Voltage, Risk of electric shock
To reduce the risk of electric shock, Do not remove the back cover.
No-user serviceable parts inside, Refer to qualified service Personnel.
FCC Information
CE Certification
This device complies with the
requirements of the MDD directive
93/42/EEC "Medical Device
Directive".
FCC (U.S.Federal Communications Commission)
This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy, and if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause unacceptable inter-
ference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Warning
- This apparatus must be earthed because of
Class I equipment.
- This apparatus is no patient contact equipment.
- When using at 240 V in United States,
supply must be from center-tapped, 240 V,
single phase circuit.
- Please consult with the dealer from whom you
purchased it about waste disposal.
- This equipment shall not to be used around the
patient vicinity, which is the space with surfaces
likely to be contacted by the patient or an
attendant who can touch the patient.
This encloses a space within the room 1.83 m
(6 feet) beyond the perimeter of the bed in its
intended location, and extending vertically 2.29
m (7-1/ 2 feet) above the floor.
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Equipment Classification
- Type of protection against electric shock:
Class II equipment
- Consult your dealer or an experienced
radio/TV technician for help.
- Protection against harmful ingress of water :
Ordinary Equipment (IPX0)-No protection.
- Not suitable for use in the presence of a flammable
anesthetics or oxygen.
FCC Warning:
To assure continued FCC compliance, the
user must use a grounded power supply cord
and the provided shielded video interface cable
with bonded ferrite cores. Also, any unauthorized
changes or modifications to this monitor would
void the user's authority to operate this device.
- Mode of operation: Continuous operation
The Responsible Party located
within United States
U.S.ELECTRONICS, INC.
Tel:1-888-926-2605
- 3 -
Follow the instructions below for safety use of the color LCD monitor.
-Read this user’s manual and properly use the unit.
-You must agree that Kodak is not liable for any damage caused by any third party’s or your
negligence of following the instructions of this user’s manual and misuse except those specified
responsibilities for compensation accepted by law.
●Symbols
-This user’s manual contains various symbols to
Person could be at risk of severe
guide users to properly use the product.
injury or death.
-The contents in each box below express the events
Warning
that will occur following neglects of signs and
Person or properties could be at risk
of injury or damage.
misuse.
-Confirm the contents shown here and then read
this manual carefully.
Caution
●Meaning of symbols
expresses DO NOT.
expresses MUST DO.
Cautions when setting up
●Do not place the unit where it
is subject to direct sunlight or
near any heating device.
The cabinet and/or components
may be damaged, which may
cause generation of fever and
ignition.
●Do not put the unit on
unstable places (on a wonky
table and inclined place),
which might cause injuries
arising from its dropping or
falling.
Caution
Cautions when using
●Do not put any metal materials or
flammable foreign objects into the unit
(from vent holes).
It may lead to electric shock and/or
fire.
●Do not put the unit in such place
where it has bad air circulation,
dust, humidity, oily smoke and
steam.
Warning
It may lead to fire.
※ In case that any object mentioned
above is placed inside, mmediately
turn off the power, disconnect the
plug from outlet, and contact hops.
●Scratching or hitting with hard objects ●Do not place any container filled with
may break the unit.
water or any chemicals near the unit.
In case of containers falling down,
liquid may permeate inside and
insulation failure may occur, which
may lead to electric shock.
※ In case of any liquid entering
inside, immediately turn off the
power, disconnect the plug from
outlet, and contact shops.
●Do not use the unit turned over on its
back, pushed on its side, or
upside down.
These may lead the fever that
the unit generates to pile up
inside the unit, which may
lead to generation of fever
and ignition. Also, falling may
cause injuries.
Caution
- 4 -
●Do not use the attached AC adapter to
other devices (models with attached AC
adapter).
●Do not put the unit in such place where
it is subject to direct sunlight or near
any heating device.
It may lead to generation of fever and/or
fire. Also, do not use any other AC
adapter to this unit.
The cabinet and/or
components may be
damaged, which may cause
generation of fever and
ignition.
Caution
●During a long-hour use, take a break 10 to 15 minutes every one hour for your eyes.
Otherwise, it may cause eyestrain.
Abnormal circumstances
●In case of any abnormality such as odor,
●In the event of thunder, immediately
turn off the power and disconnect
the plug from outlet.
Lightning strikes may cause
electric shock and/or fire.
sound, and overheat taking place,
immediately turn off the power
and disconnect the plug from
outlet.
Warning
Continuance of using the unit
under such condition may lead to
electric shock and/or fire. Immediately turn
off the power, disconnect the plug from
outlet, and contact shops.
●In the event of broken panel and leaking liquid crystal, do not inhale,
swallow, or touch the liquid crystal.
It may cause you getting poisoned and/or having a skin irritation. If you put
it in your mouth, immediately gargle with water and go to see a doctor to
get a checkup. In case of taking it on your skin and/or cloth, wipe it off with
alcohol and rinse them.
Warning
Maintenance
●Do not remove the cabinet.
●Do not remodel or repair.
It may lead to fire, electric shock,
or injuries.
There are high-voltage parts inside
that may lead to electric shock.
※ Ask shops for adjustments
and inspection.
Warning
Caution
●Clean inside the monitor once a year.
The dust inside the unit may lead to fire.
※ Ask shops for adjustments and
inspection.
●Disconnect the plug from outlet when
not using the unit for a prolonged
period.
Disconnect the plug from outlet
when not using for a prolonged
period for such as trip.
- 5 -
Notes
●Even if the unit is properly used, it may have an effect on radio and/or TV reception upon the
condition of electric wave. If it is the case, give caution to the followings.
1) Ensure enough space between the unit and radio and/or TV.
2) Connect the unit and radio and/or TV to separate outlets.
●Color LCD monitor may have tiny spots and unevenness according to the displaying
conditions, but they are not any sign of failure.
●LCD panel is produced with high-definition technology, but there may be some imperfect
displaying pixels (lacking, constant lighting).
●When placing LCD panel near windows or outside for a long period of time, give caution to it;
sunlight may cause damage on the panel.
●Do not give LCD panel a strong push, scratch it, or place any object on it. It may cause LCD
panel failure.
●When using the unit in a cold place, you will see images leave traces or a dark screen, but it is
not a failure. It will go back to the normal state as temperature rises.
●Do not display still pictures for a long period of time, which may cause afterimages.
●The minimum state of the brightness adjustment may make images difficult to see.
●The quality of computer signals may have an effect on the unit’s quality. We recommend you to
select computers with high-quality video signal output.
●Instantaneous voltage change
This unit may have defects upon momentary voltage drops of power supply caused by incidents
such as lightning strikes. For the countermeasure for it, we recommend you to use devices such
as uninterruptive power supply.
Disposal of the unit
◆ Do not dispose of the unit with general wastes.
◆ Do not dispose of the unit together with general wastes.
◆ The unit contains mercury in its CCFT(Cold cathode fluorescence tube). Follow your local regulations
or rules upon disposal of the unit.
Limitation of Liability
●Kodak is not liable for damages arising from fire, earthquake, actions taken by any third party, any
other accident, any intended action, negligence, or misuse by user, or use under such abnormal
circumstances.
●Kodak is not liable for incidental damages (including, but not limited to, loss of business
profits, disruption of buisiness, change or loss of saved data) arising from use of this product or inability
to use this product.
●Kodak is not liable for damages arising from use not described in the user's manual.
●Kodak is not liable for damages arising from malfunctions caused by combination of
connecting devices.
●Kodak is not liable for damages (concerning time limit or buisiness, reduction or delay of
profits, information, and other economic hardship) arising from use of software provided by Kodak
for use of this product, even if Kodak has been advised of the possibility of such damages.
- Windows and MS-DOS are registered trademarks or brands of Microsoft Corporation within the United States and in
other countries.
- VESA is a brand of Video Electronics Standard Association.
- DirectColorCal is a registered brand of Eastman Kodak Company.
- The names of companies and products are registered brand names or brand names.
- 6 -
Auxiliaries
Confirm the auxiliaries listed below are included.
□ AC adapter
□ Power supply cord (3P wall type)
□ DVI-DVI cable
1
1
1
1
□ USB cable
□ User’s Manual (this manual)
1
1
□ Communication cable
NOTES
＊ We recommend you to keep the packing box for transportation and the like.
＊ In case of transporting and packing the unit in the packing box, carefully place it, keeping its
panel from touching any objects.
- 7 -
Features
●Use of a 20.8-inch (53cm) QXGA ultra-high-definition color LCD panel
A large screen size and clear image is obtained by using a 20.8-inch (diagonal 53cm)
QXGA (2048 x 1536 ) ultra-high-definition color LCD panel.
Note
To display the maximum resolution on DV3MC, a graphics card that can display 2048 x 1536
or 1536 x 2048 is necessary.
●High-intensity, high contrast
The 3 million pixels for displaying various medical images can be displayed at "high-resolution,"
"300:1 high contrast" and "wide viewing angle."
Maximum brightness: 160cd/m2
120cd/m2 (when the brightness stabilizing circuit is operating)
Viewing angle: ± 85 degrees both vertically and horizontally
●DVI (digital visual interface)
Employing DVI (digital visual interface) has achieved less deterioration of video signal
and high-definition image display, compared to conventional analog interfaces.
●Brightness stability
In order to restrain the brightness drift arising from the LCD backlight, the unit is installed
with our unique automatic brightness stabilizing circuit (λ-Sentinel).
As a result, the brightness drift is held down following introduction of power.
Thus stable brightness is observed over a long period of time.
●Calibration function
With the optional color sensor and DirectColorCal software, luminance and gradation
(gamma curve) of the color LCD monitor can automatically be calibrated.
●Portrait/landscape orientation
The LCD panel can be rotated by 90 degrees from portrait to landscape orientation.
The display switch between portrait and landscape is made by internal hardware rotation function.
●Power management
This unit has loaded the power management system. The power management mode functions
when either horizontal or vertical signals or both disappears, and it reduces power consumption
to less than 10W.
●VESA standard wall/arm mountings
The units is compliant with VESA's 100mm-pitch hanging tools. The tilt stand is detachable;
the unit can be set according to users' environment such as arm mounting.
Caution
-Portrait display is available only when a graphics card can display 1536 x 2048.
-When the monitor is used as a suspention type, please use a hanging arm able to support a
monitor weighing 10kg. or more.
●Obtaining standards
The product observes worldwide medical standards such as UL2601-1.
- 8 -
How to Operate
1. Names and Functions of Each Part
Operating Section
�
�
① Power switch
This turns the power of the color LCD monitor ON and OFF.
② Power indicator
No.
1
LED Status
OFF
Power Status
OFF
Color LCD Monitor Status
Power is OFF
2
The brightness stabilizing circuit is ON and
the brightness is stable
ON
3
4
The brightness stabilizing circuit is ON and
the brightness is being adjusted
Green lamp
is lit
ON
ON
Orange lamp is lit
Power saving mode
- 9 -
Connection Section
Portrait (shorter side at the top)
�
�
�
�
�
�
�
Left side view
③ USB upstream port
Connect this port to the upstream connector from the computer. For the connection, use a USB
cable 2 meters or shorter in length.
④ USB downstream port x 2
Connect the ports to USB devices (a MOUSE, etc.) with a maximum current consumption of no
greater than 100mA per port.
Connect the color sensor when you operate color calibration.
⑤ DC power connector (DC IN 12V)
Connect the attached AC power adapter to the +12VDC power source connector.
⑥ VIDEO input connector (SIGNAL)
Connect a signal cable to the graphics board's digital video signal (DVI) connector.
⑦ REMOTE IN connector ⑧ REMOTE OUT connector
Used to control serial communication for such as brightness calibration.
⑨ Photo sensor connector
This connector is not used.
Caution
The ③ and ④ USB hubs are bus-powered types. These do not require external power
supply and are for connecting to equipments with little dissipation power like a mouse.
- 10 -
2. Adjusting the Display Angle
The screen angle can be arranged by up to 70 degrees either to the right or left, bent down by up to 3
degrees and bent up by up to 17 degrees. As indicated in the drawing below, the adjustment is con-
ducted by holding the color LCD display in both hands and slowly moving it.
17 degrees
70 degrees
70 degrees
3 degrees
Caution
Be careful not to catch your fingers when adjusting the angle holding the bottom of the LCD
panel and turning the panel.
- 11 -
3. Rotating the LCD Panel
When setting the color LCD monitor to horizontal display (landscape orientation), lift the LCD
panel to the top of the tilt stand as shown in the figure below and rotate it by 90 degrees.
Procedure
① Tilt the LCD panel upward. (Perform this procedure before sliding the panel upward.)
② Lift the LCD panel to the top (The tilt stand will slide about 60mm.).
③ Rotate the LCD panel by 90 degrees.
④ Replace the LCD panel to the bottom while in the horizontal position (landscape orientation).
①
②
③
④
- 12 -
Connection Method
1. Confirm that the computer is turned off.
2. Connect the computer’s DVI digital video output connector and the LCD monitor's "SIGNAL" with the
provided cable. When connecting the cable, do not forget to tighten the screw of the cable.
3. Connect the DC output connector of the attached AC adapter to the LCD monitor's "DC IN 12V" and
the power plug to an inlet.
4. Turn on the LCD monitor and computer. Confirm that the monitor displays images.
Example of Connection
��������
���������������
������
�������������
������
���������
���������
����������
�����������
� � � � � � � � � � �
� � � �
�������������������
Caution
Make sure you use the auxiliary AC adapter.
13
- 13 -
Handling the cable cover
1. Removing the cable cover
Lifting the hook at the top of the cover, slowly remove the cable cover and expose the cable holders.
Hook
Cable cover
2. Installing the cable cover
Secure cables to the cable holders on the back
of the stand. (Refer to the figure on the right)
Install the cable cover.
It is free to arrange cable settings according to
environment.
Caution
●Do not give signal cables or the
power cord a strong pull.
������������
●A strong pull may cause damage on
the connection part inside the
���������
monitor where high-definition
processing technology is applied. It
also may result in felling the monitor
and damaging on the LCD panel. In
the worst-case scenario, the LCD
panel will be broken.
����������
- 14 -
Antitheft security device slot
This product has loaded an antitheft security device slot compliant with MicroSaver Security System of
Kensington on the back of the color LCD monitor. MicroSaver security System can be purchased at PC
supply shops.
Antitheft security device slot
* Kensington is a registered brand of Kensington.
- 15 -
Reference
DDC*1
This unit has loaded a function compliant with DDC-2B, a VESA standard.
This function reads into the set data written in the color LCD monitor internal device in advance
on startup of Windows95/98/Me/2000 or WindowsXP and sets the detailed information of the
color LCD monitor in the system file in order to achieve Plug&Play.
Data reading from the color LCD monitor is done through a video signal cable, which needs to
be connected when Windows95/98/Me/2000 or WindowsXP is on.
*1DDC(Display Data channel)
Note
Power Management
What is power management?
This is the function that truns off the screen by detecting input signal change to reduce consumption
current for power saving.
Setting
Refer to the user's manuals of your computer and display drivers for power management settings and
time-settings for mode change.
Using Digital Input
When using DVI digital input signal, under the process of closing connected system or changing
resolution, noise will be seen. This is not a color LCD monitor failure. Pulling out or plugging into the DVI
cable during DVI digital input use may lead to failure of the display driver on the system. Pull out or plug
into the DVI cable when the system is off.
Adjustments of Luminance and Chromaticity
DV3MC does not have an OSD (adjustment button). If you need to make adjustments on luminance and
shades of color, connect DV3MC and your computer with the attached serial communication cable
(RS-232C) and install “DirectColorCal.”
* For details, refer to the user’s manual in the DirectColorCal CD-ROM.
If you wish to make adjustments on color temperature, gamma, and luminance, please purchase an
optional calibration kit.
- 16 -
Assignment of Connector Pins
Pin #
Signal
T.M.D.S. Data2-
24-pin DVI-D Connector (female)
1
2
T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4-
T.M.D.S. Data4+
DDC Clock
3
4
5
6
7
DDC Data
DIGITAL Signal Connector
8
NC
9
T.M.D.S. Data1-
T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3-
T.M.D.S. Data3+
+5V Power
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Ground
Hot Plug Detect
T.M.D.S. Data0-
T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5-
T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock +
T.M.D.S. Clock -
- 17 -
Failure Diagnosis
Check the followings before requesting repair.
Countermeasure
Symptom
Verification
Power doesn't turn on!
(POWER indicator doesn't
light!).
a: Is the power cord
connected?
b: Is the power switch ON?
a: Connect the power cord (see
Pg.12).
b: Turn the power switch on.
a: Is the signal cable properly
connected?
b: Is the POWER indicator
orange?
a: Properly connect the
appropriate signal cable (see
Pg. 12).
b: Disengage the power saving
mode.
The screen is not
displayed!
c: Is the computer on?
c: Turn the computer on.
Screen doesn't properly
display
a: Is the Graphics card
properly installed onto the
computer per the operating
manual?
a: Properly install according to
the Graphics card
Operating Manual.
The entire screen is not
displayed
a: Is the Graphics card
properly set up?
a: Properly set it up according
to the Exclusive Graphics
card Operating Manual.
- 18 -
Cleaning
Cleaning the Cabinet and the Color LCD Monitor
●When cleaning, remove the AC adapter from the color LCD monitor and outlet for
safety.
●Lightly wipe off dirt on the cabinet and LCD panel surface with a hard-wrung soft cloth soaked
in a neutral cleaning solution. Follow its instruction when using a disposable cloth.
●Do not use thinner, benzine, alcohol or such on the cabinet that is made of plastic. These can
damage the cabinet, alter its quality and cause the paint to peel off.
●Do not apply insecticides and other volatile items to the cabinet. Also do not leave rubber and
vinyl products or such in contact with it for long hours. This can cause the quality to alter and
the paint to peel off.
●Cleaners usable for the color LCD panel are isopropyl alcohol (without abrasive),
non-ammonic glass cleaner, and watered-down neutral cleaning solution. Do not use organic
solvent such as acetone and toluene.
●When the display has dust on the color LCD panel surface, wipe it off with soft moist
cloth.
●Treat the color LCD panel with care. Do not rub the LCD panel surface with a
rough item or hit it on the surface. Also, do not strongly press the LCD panel surface. This can
lead to unevenness in the screen and also to failure of the product.
*An optional protection filter “MF-002” is available.
- 19 -
Specifications
Product name : Color LCD Monitor
Model : DV3MC
Items
Specifications
53 cm (20.8-inch) Color TFT Normally Black
LCD display device
Pixel pitch
Horizontal 0.207 mm × Vertical 0.207 mm
Horizontal 318.0 mm × Vertical 423.9 mm
1536 × 2048 pixels
Display area
Pixel
Display gradation
Backlight
16.77million (8 bit each)
12 cold cathode fluorescent lamps (CCFL)
Optical characteristics
of the LCD
Horizontal ......... ± 85 deg (contrast ratio 10:1)
Vertical ............. ± 85 deg (contrast ratio 10:1)
Contrast ratio.... 300:1(viewing angle vertical/lateral 0˚)
120 cd/m2 ± 20 cd/m2
160 cd/m2 over
Factory setting brightness
Maximum brightness
Input sync signal
Compliant with DVI 1.0
Available resolution
Input terminal
640 x 480, 800 x 600, 1024 x 768, 1536 x 2048(Fv=30Hz), 2048x 1536(Fv=30Hz)
24-pin DVI-D connector, 4-pin DC power input terminal, 8-pin serial connector
for communication, 8-pin serial connector for sensor connection
USB hub function
Temperature
Compliant with USB standard Rev.1.1 Bus-powered hub
USB UPstream connector x 1, USB DOWN stream connector x 2
On
Off
Temperature
:
:
:
5~35 ℃
-20~60 ℃
10~85 ％
Humidity (non-condensation)
Air pressure
30~80 ％
701~1013 hPa
266~1013 hPa
Power
AC adapter ....... Input AC 100~240 V 50/60 Hz, 2.0~1.0 A
(Model:MW116) Output DC 12 V, 6.67 A Connector 3P AC inlet
Unit ................... DC 12 V, 6.6 A
(Model:DV3MC)
Power consumption
Normal operation:
approx. 80 W (when the exclusive AC adapter used)
Power management state:Less than 10 W (when the exclusive AC adapter used)
External dimensions and
Mass (including tilt stand)
Unit only ........... 367 x 523 x 220 mm (W x H x D:when horizontal) approx. 11 kg
When packed ... 470 x 685 x 345 mm (W x H x D) approx. 17 kg
Calibration system (option) Color sensor(made by MINOLTA), DirectColorCal software
Color sensor attachment
International
standards
UL2601-1, cUL2601-1, CSA C22.2 N601.1, TÜV-GM(EN60601-1)
BSMI(Class A), MIC, FCC Class A, VCCI Class A
MDD/CE(EN60601-1, EN60601-1-2/2001, EN55011)
●The specifications and appearance will be changed for improvement without notice.
20
- 20 -
External Dimensions
Portrait (shorter side at the top)
���
【Front】
【Left side view】
Landscape (longer side at the top)
���
���
���
���
【Front】
【Left side view】
- 21 -
Technical Support
Requesting Repair
① Read "Failure Diagnosis (Pg. 18)" carefully and check them yourself.
② In case of having abnormalities on your driver, stop operating, unplug the AC cable from the outlet, and
consult dealer.Do not repair by yourself. It is very dangerous.
③
Consult your dealer for repair.
④ Use the product's packing and packing materials to send the product. Carefully place the unit in the
packing, and keep the face from touching any packing materials.
The panel surface touching the materials during transportation will cause damage on the panel surface;
we will not cover the damage.
Contact Technical Support
Consult your dealer for technical support.
Notes for User's Manual
・ Copying any part or all of this manual without authorization is prohibited.
・ The content of this manual will be subject to change without notice.
・ Although this was made carefully, please contact us if any unclear points, mistakes, or parts left out.
- 22 -
EASTMAN KODAK COMPANY
Rochester, NY 14650, U.S.A.
PZZ11-885
Printed in Japan (Recycled Paper)
MDL2106A-1A
031225
|