Installation instructions
Important - Save for the local electrical inspector’s use.
EEB 6800.0
EEB 6600.0
EEB 6500.0
1
B
43I
24
07
General
Installation requirements
The oven must be placed on a board that can support a minimum of 62.5 kg/
140 lb. The oven is placed in direct contact with the side walls of the opening
with the frame overlapping these side walls.
Turn off the power source before installing the oven.
=
WARNING! In case the oven is not installed and secured in accordance
with this installation instructions, there is a risk of tipover! Check after
installation that the fastening screws are securely seated and that the ap-
pliance cannot be moved.
=
WARNING! The furniture or adjacent side walls must be secured so the installed
oven can’t tilt.
Make sure there’s an opening in the back so there is enough air available for
cooling the oven. If there isn't an opening, cut a hole with at least 300 cm2/
45 in2 depth in one of the adjacent surfaces, preferably in the bottom board
or top cover.
Only KÜPPERSBUSCH built-in cooktops have been designed and tested
for installation above a KÜPPERBUSCH built-in oven. No other cooktops
may be used above the oven.
=
=
Only qualified personnel should perform installations and repairs on elec-
trical appliances. Do not repair or replace any part of the appliance unless
specifically recommended in this manual. Do not put your safety at risk.
All components surrounding the oven should have a temperature resistance of up
to 100 °C/210 °F. This includes varnishes, edge bands, plastic surfaces, adhe-
sives and paints. The adjacent furniture fronts should be temperature-resistant up
to at least 70 °C/160 °F.
To eliminate the risk of burns or fire by reaching over heated surface units,
cabinet storage space located above the surface units should be avoided. If
cabinet storage is to be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5 inches beyond the bottom of
the cabinets.
Installation in a high cabinet
The frame of the oven overlaps the side walls on the right and left.
Installation under a countertop
The frame of the oven overlaps the boundary of the opening on all sides.
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0
3
Installation under a cooktop
Electrical supply
The following KÜPPERSBUSCH built-in cooktops may be installed above the
oven:
Only a qualified technian can install a conduit box or replace a connection
cable.
=
Conduit box
Don’t install the conduit box in the installation area or above a worktop!
Attach it to the side, underneath the wall, or in a high cabinet under the in-
stallation surface.
There must be a hole for the conduit cable in either the bottom opening or
the wall.
Electrical supply
The power supply should be a 120/240 volts system, 3-wire with ground.
Electrical diagram
for a 120 / 240 volts system,
3-wire with ground:
Model:
„A“
„B“
„C“
EKE 854.1
EKE 854.2
EKE 804.2
EKE 604.2
103 mm
4-1/16" ≥ 80 mm ≥ 3-1/8"
3-13/16" ≥ 80 mm ≥ 3-1/8"
Be sure to install an appropriate conduit box (not furnished) to connect the oven.
Don’t shorten the conduit to facilitate service! The conduit should be routed
to permit the removal of the oven.
EGS 304.0*
EKS 304.1*
97 mm
85 mm
3-3/8"
≥ 65 mm ≥ 2-9/16"
Installation, electrical connections and grounding must comply with all appli-
cable local codes.
EKS 604.2
EKS 804.2
103 mm
4-1/16" ≥ 80 mm ≥ 3-1/8"
■ The conduit-box must be protected by a circuit breaker or fuse, having
amperage as noted in this chapter.
* The gap between the countertop and the front panel is not necessary
for the models EGS 304.2 and EKS 304.1.
Connected load
Fuse current
240 V, 60 Hz, 3.6 kW
15 A
F
F
You will find the recess size and installation conditions for the cooktop in
the installation instructions for the cooktop.
– Connect the cable to the conduit box.
When the oven is connected, the clock flashes! Set the time as described
in the user’s guide.
F
Installation
Inserting the appliance
– Push the appliance right into
the cabinet opening. Don’t
pinch the appliance cable!
Fastening the appliance
– Open the oven door and attach the
appliance with the enclosed screws -
inserted at an angle - to the cabinet
element from the inside out.
4
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0
Installing the individual telescopic
glide-out shelves (acc.-no. 601)
– Unscrew the side grids.
These screws are used to fasten the individual telescopic glide-out shelves.
– Insert the individual telescopic
glide-out shelves at the back
into the holes in the
intermediate wall and screw
the individual telescopic glide-
out shelves at the bottom front
to the side walls. (With the
shelf rack screws!)
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0
5
6
Installation instructions EEB 6800.0 / EEB 6600.0 / EEB 6500.0
KÜPPERSBUSCH
112 N. East Street, Suite C
Tampa, Florida 33602
Telephone: 813-229-7096 Fax: 813-229-0982
Customer Care line: 1 - 800 - 459 - 0844
KÜPPERSBUSCH is a brand of Teka USA, Inc.
|