VANDAL PROOF B&W
DOME CAMERA
Owners Manual
Please read the manual thoroughly before operating this unit.
VQ1032
INTRODUCTION:
Congratulations on your purchase of this Vision Q Vandal Proof B&W Dome Camera. This Dome camera
comes with a Polycarbonate construction to provide high impact protection. The heavy duty all metal base with swivel
bracket and tamper proof hardware adds extra protection against possible vandalism. This Dome camera can be
rotated up to 360° and or tilted 90° for optimum angle selection. This vandal proof camera includes a regulated
12V DC power supply, finished leads and RCA/BNC connector.
CONNECTING VISION Q CAMERA TO A 2 PAGE / 8 CHANNEL QUAD OBSERVATION SYSTEM
1.
2.
3.
4.
5.
6.
Mount the camera to the ceiling.
Connect the video extension cable (not included) from the camera to the monitor.
Connect the power extension cable (not included) to the supplied power 12V DC adaptor.
Attach the video extension cable (not included) to the monitor’s camera inputs (see diagram below).
Attach the supplied 12V DC power supply to the power extension cable and plug into an electrical outlet
Turn your monitor ON and select the desired channel to see the picture.
BACK VIEW OF LOREX 2 PAGE 8 CHANNEL QUAD MONITOR
BNC INPUTS
VANDALPROOF
B&W DOME CAMERA
VIDEO EXTENSION CABLE
(NOT INCLUDED)
CONNECTING CAMERA TO A SINGLE PAGE QUAD OBSERVATION SYSTEM
1.
2.
3.
4.
5.
6.
Mount the camera to the ceiling.
Connect the video extension cable (not included) from the camera to the monitor
Connect the power extension cable (not included) to the supplied power 12V DC adaptor
Attach the video extension cable (not included) to the monitor’s camera inputs (see diagram below)
Attach the supplied 12V DC power supply to the power extension cable and plug into an electrical outlet
Turn your monitor ON and select the desired channel to see the picture.
BACK VIEW OF STANDARD SINGLE PAGE QUAD MONITOR
BNC INPUTS
VANDALPROOF
B&W DOME CAMERA
VIDEO EXTENSION CABLE
(NOT INCLUDED)
-2-
CONNECTING CAMERA TO A TV
1.
2.
3.
4.
Mount the camera to the ceiling.
Connect the video extension cable (not included) from the camera to the TV (AV input of the TV).
Connect the power extension cable (not included) to the supplied camera’s power 12V DC adaptor.
Attach the supplied 12V DC power supply to the power extension cable (not included)
and plug into an electrical outlet.
5.
6.
Select the AV channel (AUX or Video channel) in your television to view camera. (Note: consult
your television owners manual for setting the TV to auxiliary or video mode.)
Adjust the camera to the desired viewing angle.
TROUBLE SHOOTING:
If the camera does not function properly, check the following points. If you continue to have problems, please call our
Toll Free Customer Support line for assistance.
PROBLEMS
CAUSE AND REMEDIES
NO PICTURE
DC ADAPTOR NOT PLUGGED IN
MONITOR NOT TURNED TO CORRECT
MODE OR CHANNEL
POOR PICTURE QUALITY
CLEAN THE CAMERA LENS
ADJUST THE CONTRAST OR BRIGHTNESS CONTROL
OF YOUR MONITOR
FOR MORE INFORMATION
OR TO SEE THE COMPLETE RANGE OF LOREX PRODUCTS
PLEASE VISIT OUR WEBSITE:
WWW.STRATEGICVISTA.COM
TECHNICAL SPECIFICATIONS
Image Sensor
Pixels
1/3” CCD B&W
510 x 492
Scanning System
Resolution
525 lines, 60 field/sec
380 lines
Min Illumination
S/N Ratio
White Balance
Electronic Shutter
Lens
0.5 lux
More than 48 db
Auto
1/60 – 1/100,000 sec
3.6mm
Power Consumption
Operational Temp.
Dimensions
Weight
12 V DC, 120mA
-26° - 122°F
4 7/8” Dia x 3 ½” H
17.6oz
ALWAYS USE DISCRETION WHEN INSTALLING VIDEO AND/OR AUDIO SURVEILLANCE EQUIPMENT WHEN THERE IS PERCEIVED
PRIVACY. INQUIRE REGARDING FEDERAL, STATE AND/OR LOCAL REGULATIONS APPLICABLE TO THE LAWFUL INSTALLATION
OF VIDEO AND OR AUDIO RECORDING OR SURVEILLANCE. PARTY CONSENT MAY BE REQUIRED.
BECAUSE OUR PRODUCTS ARE SUBJECT TO CONTINUOUS IMPROVEMEMT, SVC RESERVES THE RIGHT TO MAKE PRODUCT MODIFICATION
WITHOUT NOTICE AND WITHOUT INCURRING ANY OBLIGATION. E&OE
-3-
|