HOMEOWNER'S CARE AND
OPERATION INSTRUCTIONS
MERIT® SERIES
36" Multi-View Wood Burning Fireplaces
P/N 875,040M REV. N/C 01/2007
MODELS
CST-38
CPF-38
CR-3835R
CR-3835L
The information contained in this manual applies to all model fireplaces
identified on this page. This information will help you obtain safe and
dependable service from your fireplace system. Keep this document in a
safe place for future reference.
Before you start your first fire, read this Care and Operations Manual
carefully to be sure you understand your fireplace system completely.
Failuretofollowthesesuggestionscouldresultinhazardousoperationor
fireplacemalfunction, creatingaseriouspotentialforpersonalinjuryand/
or property damage.
If you have any questions regarding the safe use or operation of your
fireplace, contact your local distributor or your contractor/builder.
Most chimney systems will require onsite completion after placement of
the manufactured home.
OTL Report No. 116-F-20-4
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
2. As a general rule, denser woods contain
morepotentialheatperpound.Mostsoftwoods
offer moderate heat value per pound.
The higher the density, the more potential heat
output. A standard cord has a volume of 128
cubic feet. This figure also includes the air
space between and around the wood. The ac-
tual volume in a standard cord is between 60
and 100 cubic feet; depending on how tightly
the wood is packed.
Wood Fuel Pointers
Wood is a wonderful renewable fuel source.
Normallyitburnsclean,leavingonlyaminimum
of waste ash, provides comforting heat and can
provide a variety of aromas and visual images.
3. Differentwoodsvarywidelyinflameheights,
flame intensities, smoke characteristics and in
sparking. Most hardwoods do not spark.
Youwillwanttoknowwhichwoodsarebestfor
use. Sometimes you may want a quick, short
fire to offset a morning chill. Soft woods are
preferable in this case. Other times you would
want more slow burning and a uniform heat
output. Hardwoods are preferable for this use.
4. Most freshly cut “green” wood will not burn
wellandwillsmoke.Greenwoodcanbefrom10
to 40 percent less efficient than air-dried sea-
soned wood.
Standard
Cord of
Wood
8'
5. Moisture and resin found inside unseasoned
woodcellswillbuilduppressureunderheatand
explode as sparks.
The amount of heat available from the logs will
beaboutequalonaweightbasis.However,logs
aregenerallynotweighedsotheamountofheat
will depend on:
4'
6. Most wood needs to be seasoned 9 to 12
months to reduce the moisture content and
producegoodsteadyfires.Whenmoisturecon-
tent is reduced from 60 to 20%, the gain in heat
potential is nearly 7%.
4'
1. The type of wood used.
2. How dry it is.
3. How many logs you put in.
4. The size of the logs.
Figure 1
7. Proper storage of wood, especially during
seasoning, is essential. We recommend that
you:
HARDWOODS
DENSITY
The last statement means that one big log
weighing 10 pounds has as much heating po-
tential as 10 pounds of twigs. However, air
cannot get at the solid log to feed the fire so the
solid log will burn slowly. While you would get
the same amount of heat out of either fire, the
smaller the pieces of wood and the more air
space around them, the faster the fire will burn.
Alser, Red
Ash
Aspen
Basswood, American
Beech, American
Birch
.41
.49-.60
.38-.39
.37
.64
.55-.65
.38
a. Never store wood on the ground. This will
causerottingandinsectinfiltration.Raisewood
on flat rock or scrap wood.
Butternut
Cherry, Black
Chestnut, American
Cottonwood
Elm
Hackberry
Hickory, Pecan
Hickory, True
Honey locust
Locust, Black
Magnolia
Maple
Oak, Red
Oak, White
Poplar
Sassafras
.50
.43
b. Stack wood loosely to allow air circulation.
.34-.40
.60.63
.53
.60.66
.69-.75
.66 (est.)
.69
.48-.50
.48-.63
.59-.67
.64-.88
.42
.42
.52
.49
.64 (est.)
.50
c. Store wood where it will not be excessively
exposed to weather, such as under a tarp or
under a roof.
Disposal of ashes
Ashes should be placed in a metal container
with a tight fitting lid. The closed container of
ashes should be placed on a non-combustible
floor or on the ground, well away from all
combustible materials, pending final disposal.
Iftheashesaretobedisposedofbyburialinsoil
or other wise locally dispersed, they should be
retained in the closed container until all cinders
have thoroughly cooled.
d. Do not stack wood directly against the walls
of your home.
8. Be a knowledgeable wood buyer. There is a
difference in cord sizes. A standard cord stack
of logs is 4 ft. high by 8 ft. long by 4 ft. deep or
the equivalent of this cubic footage. A face cord
isthesameheightandlengthasastandardcord
but the depth is only the length of the logs (12,
18or24inches).Afacecordcancontainaslittle
as 25% of the wood found in a standard cord.
Sweet gum
Sycamore, American
Tanoak
Tupelo
Walnut, Black
Willow, Black
Softwood vs Hardwood
Softwoods contain about 15 percent highly
flammableresinwhichgeneratescreosotesoot
in the chimney flue. Burning softwood exclu-
sively may not be as desirable nor as safe as
burning denser hardwoods. Many experienced
fire-builders use small amounts of softwood
kindling and newspaper in conjunction with
startingafirewithsplithardwoodlogs.Hereare
some guidelines to remember:
.55
.39
If you buy by the ton, remember that wood
becomes lighter as it dries. When buying green
or wet wood, ask for some extra poundage to
allow for the extra water you will be getting.
SOFTWOODS
DENSITY
Bald cypress
Cedar
Douglas Fir
Fir
Hemlock
Larch, Western
Pine
Redwood
Spruce
.46
.31-.47
.46-.50
.32-.43
.40-.45
.52
.39-.59
.35-.40
.35-.41
.53
9. When comparing woods of the same mois-
ture content and same species, we find most
woods have approximately the same heating
potential per pound. However, most wood is
sold by volume, not by weight. To determine
the best heating source, look at the density of
various wood types. (Density is the weight for
a given size.)
1. Softwoodsproducefastwarmingandshorter
fires. Hardwoods burn less vigorously, have
shorter flames and produce steady, glowing
coals.
Tamarack
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
3
Assumingthatyouarecomparingtwostandard
cords of different species but the same volume
and moisture content, the denser species will
providemoreBTU’s.Thetableofwoodspecies/
densities reveals more helpful guidelines.
WARNING: THE CR SERIES FIREPLACES
SHOULDBEOPERATEDWITHTHEDOORS
FULLY OPEN OR FULLY CLOSED. IF THE
DOORSARELEFTPARTIALLYOPEN, GAS
AND FLAMES MAY BE DRAWN OUT OF
THEOPENING, CREATINGRISKSOFBOTH
FIRE AND SMOKE. REFER TO FIGURE 2
FOR PROPER OPERATING CONDITIONS.
STARTING A FIRE
Both Sets of Glass Doors
Fully Closed
1. To start a fire in your fireplace properly, first
check the operation of the flue damper.
CPF Models
The design of the flue damper assembly varies
for some model fireplaces. For the standard
corneropeningfireplaces(CRSeries)thedamper
is activated by a center mounted handle. The
damperisopenedbypullingthehandleforward.
To close, the handle is pushed all the way to the
backofthefirebox.ThedamperisNOTADJUST-
ABLE between the open and closed position.
Figure 4
Care and Cleaning of Your Glass Doors
Never clean the glass when the doors are hot.
Do not use ammonia or ammonia based glass
or household cleaner to clean the glass or the
door frame. An ammonia based cleaner will
damage the finish of your glass door.
Glass Doors
Fully Open or
Fully Closed
To open the damper on the CST and CPF
fireplaces, push the center damper handle
straight up. To close pull handle down.
CR Series
In most cases, a clean dampened towel fol-
lowed by a dry towel will clean the glass. To
removeanystubbornstainsfromtheglass,use
a mild soap solution and a towel dampened
with clean water and then dry with a clean dry
towel.
Figure 2
2. The grate in the firebox should be centered
on or over the bottom hearth so your fire can
breath properly. Crumble and twist plenty of
newspapers UNDER the grate and criss-cross
some small dry kindling sticks on top of the
paper or on the bottom of the grate.
CAUTION:IFASMOKINGCONDITIONEXISTS,
GLASS DOORS SHOULD BE CLOSED DURING
FIREPLACE OPERATION.
Glass Door Operating Safety
Precautions and Instructions
WARNING: THE CST AND CPF FIRE-
PLACES SHOULD BE OPERATED WITH
BOTH SETS OF GLASS DOORS FULLY
CLOSED. IF THE DOORS ARE LEFT OPEN
OR PARTIALLY CLOSED, GAS AND
FLAME MAY BE DRAWN OUT OF THE
FIREPLACE OPENING, CREATING RISKS
OF BOTH FIRE AND SMOKE. REFER TO
FIGURES 3 AND 4 FOR PROPER OPER-
ATING CONDITIONS.
3. Build a pyramid of three split logs (split will
startmuchfaster).Arrangetheunevenwoodto
provide plenty of air space between.
• The fire must always be confined within the
boundaries of the fuel grate.
• The fireplace screens must always be closed
whenever the fireplace is operated.
4. Now, light the paper at both sides of the
firebox.
•Neverslamtheglassdoorsinceitcouldcause
the glass to break.
5. Close the screens to prevent the escape of
sparks and embers.
• Do not build excessively large or hot fires.
Scorching or discoloring of the solid brass or
plated brass trim could result.
6. Close the damper only when your fire is
completelyoutandashesarecold.Keepclosed
whenfireplaceisnotinusetopreventunneces-
sary loss of heated or cooled air.
•Extremetemperaturechangescancauseglass
breakage—donotbuildahotfireandclosethe
glass doors if the doors are cold.
GLASS DOORS
The required glass door enclosures come in
two different styles; “All-GlassTM ” Twin Pane
andbi-folddesignwithtemperedglasspanes.
Removal or modifications to the glass doors
may void your warranty and cause a smoking
condition.
•Ifthetemperedglasspanebecomesscratched
or chipped, it creates a weakness in the glass
whichcancausetheglasstobreakwhenheated.
Replace the pane of glass by contacting your
nearest dealer or distributor.
Both Sets of Glass Doors
Fully Closed
CST Models
Figure 3
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
4
CAUTION: GLASS AND METAL FRAMES GET
HOT—ALWAYSUSEHANDLESTOOPENAND
CLOSE THE DOORS.
On the CR Series fireplaces, the control lever
that operatestheoutsidecombustionair valve
has been pre-installed on your fireplace. A
coverplatehasbeenmountedoverthiscontrol
lever only if the outside air kit has not been
attached. The control lever is located on the
closed end of the fireplace opening behind the
screen. To open the air damper, turn the lever
handle 1/2 turn counter clockwise (or until
levercanbemovedupward),thenre-tightenat
desired open position. To close damper, re-
verse procedure (Figure 5 ).
LINTEL EXTENSION
These Merit Multi-Open Factory-Built
Fireplaces were designed, tested and listed
with an 18" (457 mm) high viewing area, floor
to lintel. However, varying conditions such as
altitude, climate, wood type, moisture content
of fuel, dwelling design peculiarities, average
ambient air pressure and humidity may effect
the performance of this fireplace. If an unac-
ceptable amount of smoking occurs while the
doors are open, the adjustable lintel can be
moved to correct the smoking condition.
WARNING: CERTAIN MODEL FIRE-
PLACES REQUIRE THAT THE GLASS
DOORS BE CLOSED DURING OPERA-
TION. BE AWARE THAT SAFETY GLASS
IS UNPREDICTABLE WHEN HOT AND
MAY BREAK, EXPELLING HOT GLASS
INTO THE ROOM. ADVISE ALL FAMILY
MEMBERS TO REMAIN WELL AWAY
FROMTHEFIREPLACEWHENOPERAT-
ING WITH DOORS CLOSED TO AVOID
ANY POSSIBLE PERSONAL INJURY.
The lintel extension can be lowered a maxi-
mum of 2" (51 mm) using a predrilled hole
located at the top of the lintel extension. To
lower the lintel extension 1" (25 mm), drill a
1/8" (3 mm) hole where the dimple is located.
(See Figure 7.)
COMBUSTION AIR
A proper amount of combustion air is impor-
tant for your fireplace. Fireplaces consume
large amounts of oxygen. It is important to
allow an adequate supply of air. If the fireplace
is not equipped with an outside air kit, it may
not obtain sufficient amounts of combustion
air from inside the house or structure in which
it is installed. Therefore, the fire may draw
from an outside air source and pull air in
through the chimney. This may cause smoke
spillage into the room.
Control
Lever
TolowerthelintelextensiononModelCST-38,
remove the two screws from both ends of the
lintel extension (located behind the screen
assembly). Slidethelintelextensiondownand
align the desired holes in the lintel extension
with the holes in the lintel frame. Reattach
using the screws previously removed. Repeat
this procedure for the lintel extension on the
opposite side of the fireplace. (Figure 7 )
Figure 5
On the Merit Series fireplaces, the control
lever that operates the outside combustion air
valve is located on one lower side behind the
screen panel. Push the lever all the way in to
open the air valve and pull the lever all the way
out to close the air valve (Figure 6 ).
Smokespillageoftenoccurswhenafireisfirst
started,untilthefireplaceandthechimneyhas
had the opportunity to “come up to tempera-
ture” and to begin to function normally. If
smoke spillage problems persist, a window
may be opened just a crack to allow the proper
flow of combustion air to the fireplace.
Front
Frame
Open
Lintel
Frame
If your fireplace is equipped with an outside
combustionairkit,keepopenatalltimeswhen
fire is burning and close when fire is out to
prevent cold air intrusion.
Original Position
Closed
Lowest
Dimple
Position
2" (51 mm)
Lintel
Extension
Combustion Air Control
The operation and location of the outside air
controllevervariestosomeextentondifferent
fireplace models.
Figure 7
Figure 6
On Model CPF-38 the two (2) side lintel exten-
sionsareweldedtotheendlintelextension.The
lintel extension lowers similarly to the CST-38
lintel extension. However, to prevent the end
lintel extension from being misshaped, follow
the following steps while referring to Figure 7.
The outside air damper should be kept closed
on all fireplaces except when the fireplace is in
operation. If there is no heat present in the
firebox, the air damper should be closed at
night before retiring to prevent intrusion of
outside air into the home.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
5
3. Look up from inside the fireplace (damper
open) to see any obstructions in the lower flue
area.Ifpresent,shutthedamperandglassdoors
(if installed) to seal the firebox and contain any
soot that might fall. If your do not have glass
doors installed, a damp sheet covering the fire-
place opening and sealed with masking tape will
do. Then clean the flue from the top down (if an
offset system, clean per Step 2) using a proper
size chimney brush with flexible pole sections.
Don’topenthedoorsorremovethesheetuntilall
soot has settled. Vacuum, don’t sweep.
1. Remove the two (2) screws from one of the
sidelintelextension, leavingthelintelextension
on the other side attached to the lintel frame.
Onlylowertheendofthelintelextensionclosest
to the closed end (refractory wall) of the CPF-
38. Aligning the desired holes in the lintel
extension with the holes in the lintel frame and
reattach using one (1) of the screws previously
removed.
If conditions 1, 2 or 3 occur, the refractory
shouldbereplaced.Forminordefects,repairas
noted above.
MAINTENANCE GUIDELINES
Your fireplace is designed to operate trouble-
freewithminimummaintenance.However,like
any fine appliance, it deserves and requires
some housekeeping attention.
2. Remove the two (2) screws from the lintel
extension on the other side of the fireplace.
Lower the whole lintel extension to the desired
holes and reattach using the screws just re-
moved.
Your fireplace will perform better – and cer-
tainly look more attractive to family and friends
–ifitiscleanedbeforeeachuse.Beforethefirst
seasonaluseinAutumnandafterthelastfirein
Spring, it is important to inspect the fireplace
system carefully. We recommend at least two
complete fireplace inspections a year.
4. Check the metal flashing and seals around
yourchimney.Sealanycracksorloosenailhead
openings to prevent roof leaks.
3. On the lintel extension first lowered, realign
the holes as necessary then insert and tighten
the remaining screw.
5. Clean the firebox thoroughly by using a soft
brush or equivalent.
Before Each Use
WARNING: CONTINUED OVER FIRING
CAN PERMANENTLY DAMAGE YOUR
FIREPLACE SYSTEM. SOME EXAMPLES
OF OVERFIRING ARE:
REFRACTORIES
1. Clean the firebox of excessive ashes. Some
owners prefer to leave a small layer to insulate
the cold refractory below the grate which helps
fire starting.
All fireboxes contain a furnace refractory floor.
Some models also have refractory sides and
backs. These refractories are reinforced with
steel, but can be broken by improper use.
Dropping logs on the bottom refractory and
building fires directly against the refractories
can cause premature burnout of these compo-
nents. It may easily be repaired or replaced at
costs far below repair and maintenance for
masonry fireplaces.
• BURNING QUANTITIES OF SCRAP
LUMBER, PINEBRANCHES, PAPEROR
CARDBOARD BOXES WHICH EXCEED
THE VOLUME OF THE NORMAL LOG
FIRE.
If your particular model fireplace has a factory
supplied grate attached, it is permissible to
remove the grate for cleaning; however, the
grate must be re-attached to the fireplace be-
fore the next burn.
• BURNING TRASH, CHEMICALS OR
CHEMICALLY TREATED COMBUS-
TIBLES.
2. Keepthefireplacescreenscleansocombus-
tion air flows freely.
Proper care and “burn-in” of the firebox will
prolongtheperiodofenjoymentwithoutexten-
sive maintenance. For the first few uses, build
smallfires–notroaringinfernos.Thematerials
used in the refractories contain and absorb
moisture. It is important to “cure” the refracto-
ries by building only modest fires.
Creosote Formation and Removal
3. Spotcheckthebrick-likerefractoryforsmall
cracks. Heat from the fire expands it slightly.
When it cools, it contracts.
Whenwoodisburnedslowly,itproducestarand
other organic vapors, which combine with ex-
pelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney
flue of a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. Creosote
makes an extremely hot fire when ignited.
Twice A Year Check-Up
Undernormalusage, itisexpectedthathairline
cracks will appear in the refractory surface.
These hairline cracks do not affect the safe
operation of the fireplace.
Normally,twiceayear,youshouldinspectyour
fireplace following this list:
1. Inspect the opening in your chimney top and
remove any debris that could clog it. The cap is
usually held in place by four (4) screws, which
remove easily for checking or cleaning the full
length of the flue from above. Remove the
chimney top while wearing gloves to guard
against any sharp metal edges.
Thechimneyshouldbeinspectedatleasttwice
yearly during the heating season to determine
if a creosote build-up has occurred.
Refractories should be replaced when:
1. The crack opens more than 1/4" (19 mm).
If creosote has accumulated, it should be re-
moved to reduce the risk of a chimney fire.
2. Pitting in the surface is extensive and pits
become deeper than 3/16" (4.76 mm).
2. Inspect the entire flue from the top down for
obstructions such as birds nests, leaves, etc.
This may be done by using a flexible handled
chimney cleaning brush. If the chimney con-
tainsoffset/returnelbows;asoftbrushcleaning
from the top down to any elbow and then from
the firebox up to the offset/return section is the
proper method. The beam from a powerful
flashlight will help in this inspection.
If creosote build-up is found, do not use
chemical chimneycleanersthat arepouredon
a hot fire. The manufacturer considers them
dangerousandtheygenerallyonlyworkonthe
flue section nearest the fire, leaving the rest of
theflueunaffected. Itisbesttotakethetimeto
clean the flue as previously described or have
thechimneyprofessionallycleanedbyaquali-
fied chimney sweep.
3. Anypieceofrefractorylargerthan2"(51 mm)
in radius and 3/16" deep becomes dislodged.
If your refractory has a crack less than 1/4"
(19 mm) in width, a simple Refractory Patch
Kit, Model RPK, can easily be used to fill the
crack and repair the refractory.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
6
ACCESSORIES AND COMPONENTS
Less Than 10'
2' Min.
2' Min.
10'
3' Min.
3' Min.
Figure 8
12M07
12M08
12M09
36 ABF
36 ABF-BB
36 ABF-BS
“ All-GlassTM
Bi-Fold Doors
”
6. Is a vent fan, exhaust hood or central
heating/cooling system stealing combustion
air from your fireplace? If their volume is high
enough, this can cause negative pressure and
an unwanted downdraft – and smoking.
TROUBLE SHOOTING
No Smoking Allowed
Aluminum Doors
Your new fireplace is designed not to smoke if
properlyinstalledandoperatedperourinstruc-
tions. If you do experience a problem, here are
several things to check:
Your fireplace can be fitted with beautiful
aluminum doors. Model ABF doors are avail-
able for use with these fireplace. Doors are
easily fitted to the fireplace opening. Model
ABF doors come with standard black finish.
Model ABF-BB doors have a beautiful bright
brass finish.
7. Is your wood fuel too wet or unseasoned?
Or does it contain some chemical substance
that causes sputtering, smoking and toxic
fumes?
1. Remember – always check to ensure your
flue damper is in the open position before
lighting a fire!
8. Figure 8 illustrates the correct height of
your chimney top. It is unlikely that your
installation does not adhere to the installation
instructions.However,ifnotcorrect,youcould
experienceanunusualdowndraft. Usually, the
bestsolutionistoincreasethechimneyheight.
This may also be necessary if nearby trees,
adjoining roof lines or a hill is causing a
downdraft condition.
2. When lighting your fire, a little smoke may
escape into the room – more likely if the chim-
ney is cold. To correct this, hold a lighted
newspaper up inside the firebox near the open
flue damper. This will turn around any down-
draft and clear the flue of cold air. As your log
fireburnsbelow,theupdraftwillimproveasthe
chimney heats up.
To ensure warranty and to prevent a potential
fire hazard, do not use any other doors on
these appliances.
9. Remember, your fireplace has been de-
signed as a supplemental heating device only,
it is not intended to heat your entire home.
3. Is your fire too far forward? Move it toward
the back with your poker. Keep the fire well
within the confines of your fuel grate.
ENJOY YOUR FIREPLACE
4. Keep your fire up on the grate and the refrac-
tory below free of excessive ashes. The fire
needs plenty of air movement around the logs.
If you encounter any problems or have any
questions regarding the installation of op-
eration of your fireplace system, contact
your distributor. For your nearest distributor
contact:
5. If smoking occurs an hour or two after
lighting the fire, perhaps your well-insulated
house is too airtight and there is scarcely any
way for replacement air to enter and feed the
fire.Checktoseeifyouroutsidecombustionair
kit(ifinstalled)isopen.Checkoutsidetoensure
noobstructionsareinfrontofexteriorairentry.
Open a window slightly, open doors to one or
two rooms and see if this stops the smoking.
“ All-GlassTM
”
Twin Pane Doors
12M44
38TBA-BB
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
Twin Pane Doors
Your fireplace can be fitted with attractive
Twin Pane doors. Model TBA doors are avail-
able for use with these fireplace. Twin Pane
doors are easily fitted to the fireplace opening.
Model TBA-BB doors have a beautiful bright
brass finish.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
7
ACCESSORIES AND COMPONENTS
REPLACEMENT PARTS
CR-3835L
Part No.
–
CR-3835R
Part No.
–
DESCRIPTION
Fireplace Assembly
Grate
H4403
H4006
H4412
H4413
H4416
H4417
H4536
H0631
90L73
H4403
H4006
H4412
H4413
H4416
H4417
H4536
H0632
90L73
Grate Bracket Holder
Screen
Side Screen (Corner Open Only)
Screen Rod
“ All-GlassTM
Aluminum End Panel
”
12M15
12M16
38AEP
38AEP-BB
Side Rod (Corner Open Only)
Refractory Clip/Retainer Rear
Refractory Kit
Aluminum End Panel
Your CPF-38 fireplace can be fitted with a
unique aluminum end panel. Model AEP end
panels are available for use with these fire-
place. End panels are easily fitted to the fire-
place opening. Model AEP end panels come
with standard black finish. Model AEP-BB end
panels have a beautiful bright brass finish.
Touch Up Paint
CST-38
Part No.
–
CPF-38
Part No.
–
DESCRIPTION
Fireplace Assembly
Grate
H4404
H4528
H4411
H3994
H4538
H4537
H0648
90L73
H4404
H4528
H4411
H3994
H4538
N/A
Door Track
Screens
Screen Rod
Refractory Clip, Right
Refractory Clip, Left
Refractory Kit
Touch Up Paint
H0649
90L73
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
The manufacturer reserves the right to make changes at any time, without notice, in design,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
P/N 875,040M REV. N/C 01/2007
|