Quick Start Guide
English
2
NVR10
|
Quick Start Guide
If you do not have internet access, you can install the drivers packaged with the NRV10 by inserting the included
FireWire Series CD-ROM into your computer’s CD drive. Your computer will automatically display the interactive
install screen . (If the screen does not appear, you can manually start it by clicking on Start > My Computer >
FireWire Series CD-ROM.) Select your product from the menu and click “install.”
2. Follow the driver installer’s on-screen instructions.
3. At various points during the installation process,
you may be notified that the driver being
installed has not passed Windows Logo Testing.
Click “Continue Anyway” to proceed with the
installation.
4. Once the installer has completed, click “Finish.”
5. Shut down your computer.
6. Connect the NRV10 to a power outlet and to an
available FireWire port on your computer.
7. Power on the NRV10, then start your computer.
NVR10
|
Quick Start Guide
3
8. Windows will identify the new interface and ask if you want
to search the Internet for a driver. Select “No, not this time”
and click “Next.”
9. Windows will display the Found New Hardware Wizard.
10. Select “Install software automatically” and click “Next.”
11. When the Wizard has completed, click “Finish.”
12. When the installation is complete, you will see a message
stating “Your new hardware is installed and ready to use.”
Your NRV10 will appear in Windows under Control Panel >
Sounds and Audio Devices. The NRV10 Control Panel can be
accessed by clicking on the red icon in the system tray.
IMPORTANT: While it is possible to “hotplug” a FireWire device,
it is strongly recommended that you connect or disconnect
your NRV10 only when your computer is powered off. For more
information on this issue, please visit the M-Audio knowledge base
4
NVR10
|
Quick Start Guide
Installation Instructions for Mac OS X
Make certain the NRV10 is not connected to your
computer before beginning the installation.
2. Follow the driver installer’s onscreen instructions.
3. When the installer has completed, click “Close.”
4. Shut down the computer.
1. We recommend you download the latest NRV10
drivers by going to the Support > Drivers page
have the newest available drivers. Once you have
downloaded the latest drivers, the downloaded
file should automatically mount and display its
contents on the desktop. (If the file does not
mount automatically, simply double-click on the
file once it has finished downloading to view
its contents, then double-click on the installer
application).
5. Connect the NRV10 to a power outlet and to an
available FireWire port on your computer.
6. Power on the NRV10, then start your computer.
Your NRV10 will appear in Mac OS X under System
Preferences > Sound, in the Input and Output tabs.
The NRV10 Control Panel will appear in System
Preferences > Other.
If you do not have internet access, you can
install the drivers packaged with the NRV10 by
inserting the included FireWire Series CD-ROM
into your computer’s CD drive. Your computer
will automatically display the CD-ROM icon
on your desktop. Double-click on this icon to
view the contents of the disk. Next, double-click
“Open Me,” and select your product from the
drop-down menu on the welcome screen and
click “Install.”
IMPORTANT: While it is possible to “hotplug” a
FireWire device, it is strongly recommended that you
connect or disconnect your NRV10 only when your
computer is powered off. For more information on
this issue, please visit the M-Audio knowledge base
NVR10
|
Quick Start Guide
5
2
|
Connecting the NRV10
Your NRV10 is equipped with five XLR mic inputs and eight 1/4” line inputs. Connect any combination of mic and
line sources to these inputs, being sure to choose the appropriate input source on each channel’s corresponding
Mic/Line selector. If you are connecting condenser microphones, be sure to activate the Phantom Power switch.
You can connect external signal processors (typically dynamics processors) to any of the channel inserts on input
channels 1 through 4, as well as to the rear-panel Main Mix insert. You can also connect external signal processors
(typically reverbs or other multi-effects devices) to the NRV10’s Aux Send and Aux Return jacks.
Connect your powered monitor speakers or power amp to the rear-panel Main Mix outputs. The Main Mix outputs
are provided as both XLR and 1/4” TRS output connectors. Although both sets of connectors carry the same signal,
it is recommended under most circumstances that only one set of outputs be connected at any time. (Connecting to
both sets of outputs will not damage your mixer, but will result in reduced overall output levels.) You can connect an
additional set of powered monitors or a monitor amp to the rear-panel Control Room outputs.
And finally, connect the included FireWire cable from either of the NRV10’s rear-panel FireWire ports to your
computer’s FireWire input.
IMPORTANT: Routing signals incorrectly between the NRV10 and your computer-based DAW—in particular,
pressing the pre/post EQ button in certain routing configurations—can result in a feedback loop that can damage
your hearing and your equipment. Please refer to Section 10 of the included User Guide, “Monitoring Live Audio
While Recording to Your DAW,” before you use your NRV10.
6
NVR10
|
Quick Start Guide
3
|
Using the Control Panel
The Control Panel provides you with the ability to monitor some of the NRV10’s basic functions and gives you
control over some of its features. Refer to the User Guide for full information on using the Control Panel.
4
|
Additional Information and Support
news stories, FAQs and technical support. We recommend checking this site regularly to ensure you have the latest
drivers and the most up-to-date information on your M-Audio product.
© 2006 Avid Technology, Inc. All rights reserved. Product features, specifications, system requirements and
availability are subject to change without notice. Avid, M-Audio and NRV10 are either trademarks or registered
trademarks of Avid Technology, Inc. All other trademarks contained herein are the property of their respective
owners.
WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash hands after handling.
NRV10
Tested to comply with
FCC standards
FOR HOME OR STUDIO USE
M-Audio USA
|
5795 Martin Rd., Irwindale, CA 91706
M-Audio Germany
Technical Support
|
Kuhallmand 34, D-74613 Ohringen, Germany
e-mail: [email protected]
tel: +49 (0)7941 - 9870030
fax: +49 (0)7941 98 70070
Technical Support
tel (pro products): (626) 633-9055
tel (consumer products): (626) 633-9066
fax (shipping): (626) 633-9032
e-mail: [email protected]
tel: +49 (0)7941 98 7000
fax: +49 (0)7941 98 70070
Sales
Web
e-mail: [email protected]
tel: 1-866-657-6434
fax: (626) 633-9070
Sales
Web
M-Audio Canada
|
1400 St-Jean Baptiste Ave. #150, Quebec City,
Quebec G2E 5B7, Canada
M-Audio U.K.
|
Floor 6, Gresham House, 53 Clarenden Road,Watford
WD17 1LA, United Kingdom
email: [email protected]
phone: (418) 872-0444
fax: (418) 872-0034
Technical Support
e-mail: [email protected]
tel: (Mac support): +44 (0)1765 650072
tel: (PC support): +44 (0)1309 671301
Technical Support
e-mail: [email protected]
phone: (866) 872-0444
fax: (418) 872-0034
Sales
Web
tel: +44 (0)1923 204010
fax: +44 (0)1923 204039
Sales
Web
M-Audio France
|
Floor 6, Gresham House, 53 Clarenden Road,Watford
WD17 1LA, United Kingdom
tel : 0 810 001 105
e-mail : [email protected]
Renseignements
Commerciaux
PC : 0 0820 000 731
MAC : 0 0820 391 191
Assistance Technique
Assistance Technique
Site Web
e-mail : [email protected]
fax : +33 (0)01 72 72 90 52
|
060104_NRV10_QSG_EN01
|