Operation
and Installation
Manual
Model: M3500DVD
DVD/CD Receiver
with AM/FM Tuner
Location and Function of the Controls
1. Equalizer/Loud Button (EQ): Press to select
12. Multi-Function Button (4, INT):
between the preset sound equalization settings.
Press and hold the button to boost high and low
tones at low volume levels (loudness).
Radio: Recalls a memorized radio station,
and programs a radio station into memory.
CD: Press to activate the intro function which
will play the beginning of every track for
10 seconds.
��
2. Down ( l
��
) and Up (
l ) Controls:
Radio: Press and release to manually adjust the
radio frequency down or up. Press and hold
to automatically scan to the next radio station.
13. Multi-Function Button (3, RDM):
Radio: Recalls a memorized radio station,
and programs a radio station into memory.
DVD, CD, SD or USB: Press to randomly play
tracks/chapters.
DVD, CD, SD or USB: Changes tracks or
chapters
.
3. Mode Button (MODE): Press the MODE button to
change the operating mode as follows: “AVIN F”
Audio/Video In, Front > “AVIN R” Audio/Video In,
Rear > “F1, F2, F3, AM1 or AM2” Radio > “LOAD”
Music or Movie Disc > “USB” USB > “CARD” SD
14. Multi-Function Button (2, A-B):
Radio: Recalls a memorized radio sta-
tion, and programs a radio station into
memory.
card*
.
DVD, CD, SD or USB: Continuously repeats a
selection of music/movie.
*Available only when there is media inserted
into Disc slot, USB slot or SD Card slot.
15. Multi-Function Button (1, RPT):
Radio: Recalls a memorized radio sta-
tion, and programs a radio station into
memory.
4. Volume/Select Knob (VOL/SEL)
Volume: Rotate VOL knob to adjust the volume
level.
Select: Press the VOL knob to enter the sound
characteristics menu. Pressing the VOL
knob will change the menu item as follows:
“BAS” bass > “TRE” treble > “BAL” balance
> “FAD” fader > “STEREO” stereo/mono FM
reception > “BEEP OFF” beep confirmation
for button press > “USA” radio frequency >
“VOL” volume.
DVD, CD, SD or USB: Press to repeat the cur-
rent track/chapter. Press again to cancel the
repeat function.
16. Radio Band Button (BAND): Selects the desired
radio band in the following order: F1, F2, F3,
AM1 and AM2.
17. IR Eye for Remote Control
5. Automatic Memory Station (AMS): Press and hold
for automatic station memory storing. Press and
release for scanning memorizes stations.
�
18. Play/Pause Button ( ll):
DVD, CD, SD or USB: Press to pause the
current track/chapter. Press again to
resume play.
6. Display Area: Displays: radio, disc, SD card and
USB functions.
19. Power/Mute Button (
MUTE):
7. USB Input: Plug in your USB device, “LOAD”
then “USB” will appear in the display.
Power: Press to turn the unit on when the
unit is off, press and hold the button to
turn the unit off.
8. Face Plate Release Button (OPEN): Press to open
face plate to allow access to disc slot, SD card
slot and disc eject button.
Mute: When the unit is on press and release
this button to mute the audio, press again to
restore the audio.
9. 3.5mm Auxiliary Audio/Video Input Jack: Plug-in
20. SD Card Slot: Insert a SD card with the notch
a device with a 3.5mm audio/video input plug.
in the card facing down, “LOAD” then “CARD”
will appear in the display
.
10. Multi-Function Button (6, +10):
Radio: Recalls a memorized radio station,
and programs a radio station into memory.
DVD, CD, SD or USB: Press to skip up 10
tracks/chapters.
21. Eject Button ( ): Ejects the disc from the
DVD/CD slot.
22. Disc Slot: Insert a disc into the slot with label
facing up.
11. Multi-Function Button (5, -10):
Radio: Recalls a memorized radio station,
and programs a radio station into memory.
DVD, CD, SD or USB: Press to skip down 10
tracks/chapters.
23. Reset Button: Press the RESET button if the
unit freezes up or does not function correctly.
3
Remote Control Button Locations and Functions
Inserting the Batteries into the Remote Control:
1. Open the battery compartment cover.
2. Insert the new batteries. Make sure that the
positive and negative terminals of the batteries
are oriented as indicated.
9. Display (DISP): Displays source information.
10. Band: Selects F1, F2, F3, AM1 or AM2 radio
bands.
11. Equalizer/Loud (EQ): Press to select between
the preset sound equalization settings.Press
and hold the button to boost high and low
tones at low volume levels (loudness).
3. Close the cover.
Using the Remote Control:
Point the remote control towards the IR eye on
the radio.
12. Mute: Mutes the audio.
Note: Operation angle is about 30 degree in each
direction. Operation distance is about 15ft.
13. Numeric Keypad: Inputs the corresponding
number.
14. Mode: Switches through the available sources.
14
15
15. Menu: Displays the movie menu.
16. Title: Displays the title menu that is stored on
16
17
the movie disc.
1
2
POWER
MODE
MENU
TITLE
�� ��
,
to fast
17. Disc Fast Rewind/Fast Forward (
).
��
Press the fast forward button
3
5
18
4
forward disc play or press the fast reverse but-
RANDOM
ZOOM
REPEAT
ENTER
EQ
��
ton
to fast reverse disc play. Each time
19
6
7
VOL
TONE
the button is pressed, the speed changes. To
SETUP
20
21
�
resume normal play, press the play button ll.
�� ��
8
18. Tune/Track/Chapter (l
,
l) :
9
Radio: Press and release to manually adjust
the radio frequency down or up. Press
and hold to automatically scan to the next
station.
DISP
BAND
MUTE
SLOW
AUDIO
22
23
10
SUB.TT
24
11
13
12
1
5
9
2
6
3
Disc: Press to change to a lower or higher
track/chapter.
4
8
7
+
19. VOL/TONE :
Press to change the menu item as follows:
“BAS” bass > “TRE” treble > “BAL” balance >
“FAD” fader > “STEREO” stereo/mono FM recep-
tion > “BEEP OFF” beep confirmation for button
press > “USA” radio frequency > “VOL” volume.
10/0 10
1. Power On/Off: Turns the unit On or Off.
2. Play/Pause ( ): DVD, CD, SD or USB: Press
to pause the current track/chapter. Press again
to resume play.
20. SETUP:
Access the Movie Disc Setup Menu, a movie
disc has to be inserted.
21. + ,
-
(Volume Adjustment):
Press to increase or decrease the volume level.
They also adjust Bass, Treble, Balance and
Fader when selected.
3. Stop ( ): Stops disc play.
4. Random: Press to randomly play tracks/chapters.
5. Repeat: Repeats play of chapters, titles, tracks
and discs.
22. Slow: Press to play the movie disc in slow
motion.
23. Subtitle (SUB.TT): Accesses movie disc’s sub-
6. Zoom: Enlarges or reduces the size of movie picture
.
title languages.
�
�
7. Cursor: (s, , t, ): Moves feature selec-
24. Audio: Changes the language on multi-language
tion up, down, left or right.
movie discs.
8. Enter: Confirms the selected item.
4
General Operations
Turning the Unit On:
Press the
unit is off.
button to turn the unit On when the
MODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
Turning the Unit Off:
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
Press and hold the
button to turn the unit Off.
Mode Selection:
MODE
Press the MODE button to change the operating
mode as follows: “AVIN F” Audio/Video In, Front
> “AVIN R” Audio/Video In, Rear > “F1, F2, F3,
AM1 or AM2” Radio > “LOAD” Music or Movie
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
Disc > “USB” USB > “CARD” SD card*
.
*Available only when there is media inserted
into Disc slot, USB slot or SD Card slot.
Sound Controls
Volume:
Decrease
Increase
•
Increase the volume by rotating the knob clock-
wise.
MODE
EQ
AMS
•
Decrease the volume by rotating the know counter-
clockwise.
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
VOL
+
10
RPT
A-B
RDM
INT
4
10-
5
1
2
3
6
Sound Characteristics Menu:
By pressing the VOL knob, the modes will be dis-
played in the following order: “BAS” bass, “TRE”
treble, “BAL” balance and “FAD” fader.
MODE
EQ
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
INT
4
10-
5
VOL
3
6
Balance:
Bass:
Press the VOL knob button until “BAL” appears
in the display. Turn the VOL knob clockwise to
increase the balance to the right and counter-
clockwise to increase the balance to the left.
Press the VOL knob until “BAS” appears in the
display. Turn the VOL knob clockwise to increase
the bass and counterclockwise to decrease the
bass.
Fader:
Treble:
Press the VOL knob button until “FAD” appears
in the display. Turn the VOL knob clockwise to
increase the balance to the front speakers and
counterclockwise to increase the balance to the
rear speakers.
Press the VOL knob button until “TRE” appears
in the display. Turn the VOL knob clockwise
to increase the treble and counterclockwise to
decrease the treble.
Equalizer:
The M3500DVD has pre-programmed audio set-
tings. Press the EQ button to switch the equalizer
settings. The equalizer setting will appear in the
display: POP, ROCK, CLAS (classic) or off. The
unit will leave equalizer programing after 5 sec-
onds of no button activity.
ODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
A-B
RDM
INT
10-
VOL
1
2
3
4
5
6
5
Sound Controls (continued)
Loudness:
Hold
To boost high and low tones at low volume lev-
els, press and hold the EQ button until “LOUD”
appears in the display. To deselect, press and
hold the EQ button again until “LOUD” disap-
pears from the display.
ODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
Mute:
MODE
Press the
MUTE button to cutoff the audio.
EQ
AMS
Press it again to restore the audio.
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
Radio Operation
Selecting a Band:
1. Press the MODE button until either “F1, F2,
F3”, AM1 or AM2” appears in the display.
MODE
MODE
MODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
VOL
6
2. Next press the BAND button to select the
desired band: “F1, F2, F3” (FM) or “AM1,
AM2” (AM).
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RP
1
A-B
2
RDM
3
INT
4
10-
5
6
Manual Tuning:
��
��
Press and release the
l or l
button until
EQ
AMS
desired frequency is selected.
MUTE
Automatic Search Tuning:
Press and hold the
AM/FM Multi-Media Receiver
D
SE
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
��
��
l or l
button to
6
move to the next or previous station automati-
cally. Then release and press and hold the but-
ton again to scan to the next radio station.
Down
Up
Preset Radio Stations:
The six numbered preset buttons can store and recall
stations for each band (F1, F2, F3, AM1 or AM2).
Radio Band
Preset Number
MODE
EQ
AMS
Memorizing a Station:
1. Select a radio band.
MUTE
2. Tune in a radio station.
AM/FM Multi-Media Receiver
BAND
SEL
VOL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
3. Press and hold any of the preset buttons for
three seconds to memorize the station. The
preset number will appear in the display.
6
Radio Station
Recalling a Station:
1. Select a band (F1, F2, F3, AM1 or AM2)
.
2. Press one of the six preset buttons to select
a stored station.
6
Radio Operation (continued)
Preset Radio Stations (continue)
Automatically Memorizing Station:
1. Select a band (AM or FM).
MODE
EQ
AMS
MUTE
2. Press and hold the AMS button for two sec-
onds. The radio automatically selects strong
stations and stores them in each preset
number for the selected radio band. The
new stations replace stations already stored
in that band.
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
3. After the new stations are stored into memory,
the tuner will start playing the memorized stations
each for 5 seconds. When a desired station is
reached, press the AMS button to stop scanning.
Scanning Memorized Stations:
To scan preset stations stored in the current
band press and release the AMS button. The
radio pauses for five seconds at each preset
station. When the desired station is reached,
press the AMS button again to stop scanning.
FM Stereo/Mono Reception:
For weaker FM stereo stations selecting mono
reception usually improves reception. To switch
from stereo to mono reception press the VOL knob
until “STEREO” appears in the display. Rotate the
VOL knob until “MONO” appears in the display.
The unit will leave feature programing after 5 sec-
onds of no button activity.
MODE
EQ
MS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
CD (Music) Disc, SD Card and USB Drive Operation
Loading a CD:
1. Press the OPEN button to flip down the face
and to allow access to the disc slot.
OPEN
MODE
AMS
2. Insert a CD into the disc slot with the label side
up. Inserting the disc will automatically switch
the unit to the “CD” mode.
AM/FM Multi-Media Receiver
USB
BAND
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
AUX
6
3. Close the unit’s face.
Label Side Up
Ejecting a CD:
1. Press the OPEN button to flip down the face
and to allow access to the disc slot.
2. Press the button to eject the disc from the
unit. Remove the disc.
3. Close the radio face.
7
CD (Music) Disc, SD Card and USB Drive Operation (continued)
Inserting the USB Drive:
1. Flip open the door to allow access to the USB slot.
OPEN
AMS
2. Gently insert the USB drive into the slot.
Inserting the USB drive will automatically
AM/FM Multi-Media Receiver
UB
BAND
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
switch the unit to the “USB” mode.
AUX
6
Note: If a drive does not insert, DO NOT FORCE
it into the slot, flip the drive over and try again
.
Removing the USB Drive:
Remove a USB drive at any time by pulling the
device out of the socket.
Inserting the SD Card:
1. Press the OPEN button to flip down the face
and to allow access to the SD slot.
OPEN
MODE
AMS
2. Gently insert the SD card into the slot with the
angle key in the card facing down until it clicks
into place. Inserting the SD card will automati-
cally switch the unit to the SD “CARD” mode.
Note: If a card does not insert, DO NOT FORCE
it into the slot, flip the card over and try again.
3. Close the unit’s face.
AM/FM Multi-Media Receiver
USB
BAND
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
AUX
6
Removing the SD Card:
1. Press the OPEN button to flip down the face
and to allow access to the SD slot.
2. Push in on the SD card until you hear a click,
then release the SD card and remove it.
3. Close the unit’s face.
Select Tracks:
Track Number
��
��
Press and release either the
l or l
button
MODE
EQ
for less than a second to move to the next or
previous track. The track number appears in the
display area.
AMS
MUTE
AM/FM Multi-Media Receiver
D
SE
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
6
Pause Play:
MODE
�
EQ
Press the ll button to pause play. Press it again
AMS
to resume play.
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VO
6
CD Repeat Function:
The default setting is to repeat the entire disc. Press
the 1/RPT button to change the repeat function:
“REPEAT OFF” = Disc will stop playing at end
of disc.
MODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
“REPEAT 1”
= The track playing will
continuously repeat.
“REPEAT ALL” = The entire disc repeats
continuously.
8
CD (Music) Disc, SD Card and USB Drive Operation (continued)
Disc, USB or SD Card Repeat Function:
MODE
EQ
The default setting is repeat is off. Press the
AMS
1/RPT button to change the repeat function:
MUTE
“REPEAT 1”
= The track playing will
continuously repeat.
AM/FM Multi-Media Receiver
+
BAND
SEL
RPT
1
A-B
2
RDM
3
INT
4
10-
5
10
6
VOL
“REPEAT DIR” = The entire directory will
continuously repeat.
“REPEAT ALL” = All the tracks will
continuously repeat.
“REPEAT OFF” = Will stop playing at end
of last track.
Play All Tracks in Random Order:
Press the 3/RDM button to play all tracks in random
order. Press it again to stop playing in random order.
MODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
RDM
3
INT
4
10-
5
VOL
6
CD Intro Scan:
MODE
Press the 4/INT button to play the first ten sec-
onds of each track. Press it again to stop intro
scan and listen to the track.
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
INT
4
10-
5
VOL
6
Track Skip Buttons:
Press the 5/-10 button to skip down 10 tracks.
Press the 6/+10 button to skip up 10 tracks.
MODE
EQ
AMS
MUTE
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
10-
5
VOL
6
Auxiliary Audio/Video Input
Front Audio/Video Input Jack:
OPEN
1. Connect an audio/video device using a 3.5mm
jack (not supplied) into the socket mounted on
the front of the unit.
2. Press the MODE button until “AVIN F” appears
in the display.
AMS
AM/FM Multi-Media Receiver
USB
BAND
+
10
RPT
1
A-B
RDM
3
INT
4
10-
5
AUX
2
6
Note: The unit will not control the auxiliary source,
but can adjust the sound controls. Refer to the
audio/video device’s owners manual for proper
operation.
MODE
EQ
AMS
MUTE
Rear Audio/Video Input:
1. An auxiliary audio/video device must be con-
nected to the rear of the unit.
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
RDM
3
INT
4
10-
5
VOL
2
6
2. Press the MODE button until “AVIN R” appears
in the display.
9
DVD (Movie) Disc Operation
Loading a DVD:
OPEN
MODE
1. Press the OPEN button to flip down the face
and to allow access to the disc slot.
AMS
2. Insert a DVD into the disc slot, label side up,
and the DVD will begin to play.
AM/FM Multi-Media Receiver
USB
BAND
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
AUX
6
3. Close the unit’s face.
Label Side Up
Ejecting a DVD:
1. Press the OPEN button to flip down the face
and to allow access to the disc slot.
2. Press the
button to eject the disc from the
unit. Remove the disc.
3. Close the radio face.
Menu Screen:
1. Press the MENU button on the remote to
access the menu screen of the movie disc.
POWER
MODE
REPEAT
MENU
TITLE
�
�
2. Use the s, , t, buttons on the remote
to navigate to the menu item you want.
3. Press the ENTER button to execute your
selected menu item.
RANDOM
Pausing/Playing a Movie Disc:
MODE
EQ
�
Press the ll button to pause the movie disc.
AMS
“PAUSE” will appear in the display.
MUTE
AM/FM Multi-Media Receiver
+
BAND
�
SEL
To resume playing the disc, press the ll button.
RPT
1
A-B
2
RDM
3
INT
4
10-
5
10
6
VO
Stopping a Movie Disc:
Press the � button on the remote control to
POWER
RANDOM
MODE
MENU
TITLE
�
stop play. To resume play, press the ll button.
�
Press the � button 2 times, then press the ll
button and the movie disc will start playing from
the beginning.
REPEAT
Selecting a Chapter:
Chapter Number
��
Press and release the l
previous chapter.
button to select a
MODE
EQ
AMS
��
Press and release the
next chapter.
l button to select a
MUTE
AM/FM Multi-Media Receiver
ND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
6
10
DVD (Movie) Disc Operation (continued)
ENTER
Subtitle Language Menu:
P
ress the SUB.TT button on the remote during
DISP
BAND
MUTE
SLOW
AUDIO
playback. Each time the button is pressed, the
subtitle language changes. The selection of sub-
title appears at the top of the screen.
EQ
SUB.TT
Notes:
1
2
3
1. Some discs may contain only one subtitle
language.
2. Depending on the disc, the number of subtitle
languages may be different.
Zoom Selection:
RANDOM
ZOOM
REPEAT
ENTER
1. Press the ZOOM button on the remote to
VOL
TONE
enlarge the on-screen image during disc play.
Each time the ZOOM button is pressed, the
magnification increment changes in the fol-
lowing order: 2X, 3X, 4X, 1/2, 1/3, 1/4.
SETUP
SLOW
DISP
�
�
2. Use the navigation buttons s, , t, on
the remote to move the image on the screen.
VOL
TONE
ZOOM
SETUP
On Screen Display Selection:
P
ress the DISP button on the remote during
ENTER
movie play to display the following information in
this order for most discs:
DISP
SLOW
AUDIO
Title Elapse, Title Remain, Chapter Elapse,
Chapter Remain and Display Off.
BAND
EQ
SUB.TT
Fast Forwarding / Fast Rewinding:
��
��
Press the
or
button on the remote
to start the fast forward or fast rewind function
speed of 2 times normal speed (X 2). “FORWARD
X 2 or BACKWARD X 2” will appear in the display.
POWER
MODE
REPEAT
MENU
TITLE
��
��
Press and hold the
or
button again will
RANDOM
ZOOM
increase the speed, X 4, X 8 and X 20. Press the
�
ll button to resume normal movie disc playback.
VOL
TONE
SETUP
Slow Motion:
Continue to press the SLOW button on the remote
to play the movie is slow motion in the following
order:
ENTER
DISP
SLOW
AUDIO
SF 1/2, SF 1/3, SF 1/4, SF 1/5, SF 1/6, SF 1/7
BAND
EQ
SUB.TT
�
To resume normal play, press the ll button.
ENTER
Audio Language:
P
ress the AUDIO button on the remote during
DISP
BAND
MUTE
SLOW
AUDIO
playback to select the desired audio/language
setup. The audio languages will appear at the top
of the screen.
EQ
SUB.TT
1
2
3
11
DVD (Movie) Disc Operation (continued)
Title Screen:
P
ress the TITLE button on the remote, depend-
POWER
RANDOM
MODE
REPEAT
MENU
TITLE
ing on the characteristics of the movie disc
the title function may be invalid. This is not a
malfunction.
Direct Chapter Selection:
1. Using the numeric keypad on the remote con-
trol enter the chapter number.
MUTE
4
1
5
9
2
6
3
7
2. Press the ENTER button to confirm.
+
8
10/0 10
Last Play Memory:
•
During disc play, if you turn off the unit and
turn it on again, the movie will resume playing
from where it was stopped
.
•
During disc play, if you press the MODE but-
ton to switch to another mode, and return to
the movie mode again, the unit will resume
playing from where it was stopped.
12
DVD (Movie) Disc Operation (continued)
Screen Adjustment Controls:
RANDOM
ZOOM
REPEAT
ENTER
1. Press the SETUP button on the remote to
enter the setup menu.
OL
TONE
SETUP
2. When the cursor is on the top of the screen
�
�
use or button to select different pages,
such as: SYSTEM SETUP, LANGUAGE
SETUP, VIDEO SETUP, SPEAKER SETUP and
DIGITAL SETUP.
3
4
. Press t button to move the cursor to SETUP
page below and use s and t buttons to
move among the different SETUP options.
VOL
TONE
ZOOM
SETUP
SLOW
ENTER
�
. Press button to display the list of choices
for each SETUP menu item. Use s and t to
DISP
change selection.
5. Press ENTER button to confirm your selection.
SYSTEM SETUP
TV SYSTEM
AUTO PLAY
TV TYPE
PASSWORD
RATING
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LAN
MENU LANG
DEFAULT
- TV SYSTEM: NTSC, PAL or AUTO
- AUTO PLAY: On or Off
- TV TYPE: 4:3 PS, 4:3LB or 16:9
- PASSWORD: Lock/unlock (default 0000)
- RATING: 1KID SAFE, 2G, 3PG, 4PG13, 5PG-
R, 6R, 7NC17 or 8ADULT.
- DEFAULT: Restore the SYSTEM SETUP
menu.
- OSD LANGUAGE: English, German, Spanish,
French and Portuguese.
- AUDIO LANGUAGE: Chinese, English,
Japan, French, Spanish, Portuguese, Latin
and German.
- SUBTITLE LANGUAGE: Chinese, English,
Japan, French, Spanish, German and Off.
- MENU LANGUAGE: Chinese, English, Japan,
French, Spanish, Portuguese, German and
Latin.
VIDEO SETUP
BRIGHTNESS
CONTRAST
HUE
SPEAKER SETUP
DOWNMIX
FRONT
SATURATION
SHARPNESS
You can adjust the value of brightness, con-
trast, hue, saturation and sharpness.
- DOWNMIX: LT/RT, STEREO or VSS
- FRONT: Large or Small
13
Wiring Diagram
White/Black Wire
Gray/Black Wire
Gray Wire
Left
Front
Speaker
Right
Front
Speaker
White Wire
Audio Output Right (Red)
Audio Output Left (White)
Video Output (Yellow)
Video Input (Yellow)
Audio Input Left (White)
Audio Input Right (Red)
External Antenna
Violet/Black Wire
Violet Wire
Left
Rear
Speaker
Green/Black Wire
Green Wire
Right
Rear
Speaker
Red Wire (+) to 12 Volt Ignition
Black Wire Ground
Yellow Wire (+) to 12 Volt Constant
Blue Wire Power Antenna (12V Out)
14
Installation Procedures
Mounting Sleeve
Sheet Metal
Screw
Nut
Washer
Push Out Mounting
Sleeve Tabs
Metal Strap
Dashboard
Removal Keys
Installing the Unit:
1: Insert the sleeve into the dashboard opening and
Removing the Unit:
1: Remove the trim ring.
bend the mounting tabs outward to secure it.
2: Insert the release keys into the left and right
2: If necessary, attach the mounting strap to the rear
side of the unit.
of the unit, then attach it with the supplied nut.
3: Pull the unit out of the dashboard.
3: Insert the unit into the sleeve until you hear a click.
4: Finally place the trim ring over the unit.
15
Reset Function
Press the OPEN button on the front panel to fold
down the panel, and you will see the RESET but-
ton on the base of the unit.
When the below situation occurs, you can press
the RESET button to solve the problem:
• Initial installation of the unit when all wiring
is completed.
• Some of the buttons do not work.
• Error symbol on the display.
Should any of these conditions occur, simply
press and release the restart button using the tip
of a ball point pen. This will restart the radio’s
microprocessor. After pressing the restart but-
ton, you should recheck to see if the radio func-
tions normally.
Additional Features
Button Press Beep Confirmation:
If you want the M3500DVD to beep everytime a
button is pressed follow the instructions below:
MODE
EQ
MS
MUTE
AM/FM Multi-Media Receiver
1. Press the VOL knob until “BEEP OFF” appears
in the display.
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
2. Rotate the VOL knob until “BEEP ON” appears
in the display
.
3. After waiting a few seconds the unit will exit
programming.
Area Radio Frequency Adjustment:
Note: If operating the unit in the USA do not
change the area.
MODE
EQ
MS
MUTE
To Change the Area:
AM/FM Multi-Media Receiver
BAND
SEL
+
10
RPT
1
A-B
2
RDM
3
INT
4
10-
5
VOL
6
1. Press the VOL knob until “USA” appears in the
display.
2. Rotate the VOL knob until “OCEAN” appears in
the display
.
3. After waiting a few seconds the unit will exit
programming.
16
Troubleshooting
The disc can not play:
If it appears that your unit does not operate prop-
erly, first consult this checklist. It may be some-
thing simple which has been overlooked.
• Disc is of poor quality or damaged or not clean.
Clean or replace the disc with one of higher
quality.
• The disc installed is not supported by the unit.
Examine the disc type.
Under no circumstances should you try to repair
the player yourself, as this will invalidate the
warranty. Only qualified service personnel can
remove the cover or service this player.
Disc can not be loaded or ejected:
The power does not turn on:
• Hold the
button for 5 seconds to reset the
mechanism. Turn off the unit, and turn on the
unit again.
• The lead wires are not connected properly to
the connectors. Make sure the connection is
correct.
The desired source is not selected although you
press the MODE button:
• An optional unit required to listen to each
source is not connected yet. Connect the
optional unit correctly.
• One of the fuses has blown. After checking for
short circuits in the wires, replace the fuse
with one having the same rating.
• The internal processor is not working due to
noise or other factors. Press the reset button to
reset the unit to factory defaults.
• The reset button is not pressed yet although the
optional unit has been connected to the unit.
Press the RESET button.
The remote control does not work. The unit does
not operate even when the correct buttons on the
remote control are pressed:
• Battery capacity is low. Install new batteries.
• Some operations are disabled in specific
modes. Enter the correct mode.
Replaceable Fuses
If the fuse should blow, check that the wiring is
correct. If the wiring is correct, replace the fuse
with the same amperage rating as the original.
Yellow Wire = 15 Amp glass fuse.
Red Wire = 1 Amp glass fuse.
17
Disc Warnings
Handling:
• Dirt, dust, scratches and warping disc will cause
non-operation.
Label side up
• Do not place stickers on disc or scratch disc.
• Do not place discs in the following places: Direct
sunlight, dirty, dusty or damp areas, near car
heaters, car seats or dashboard.
Do not touch
the underside
of the disc
Disc Cleaning:
Use a dry, soft cloth to wipe the disc’s surface. If the
disc is very dirty, use a soft cloth slightly moistened
with isopropyl (rubbing) alcohol. Never use solvents
such as benzine, thinner or conventional record
cleaners as they may mar the surface of the disc.
Do not bend
Wipe the disc from
the center toward
the outside edge
Note: A disc may become somewhat scratched
(although not enough to make it unusable)
depending on handling and conditions in the usage
environment.
Preparing New Discs with Rough Spots:
A new disc may have rough edges on its inside
and outside edges. If a disc with rough edges is
used, the proper setting will not be performed and
the player will not play the disc. Therefore, remove
the rough edges in advance by using a ball point
pen or pencil as shown. To do this, press the side
of the pen or pencil against the inside and outside
edges of the disc.
Rough spots on
outside edge
Rough spots on
inside edge
Ball point pen
or pencil
18
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within one year from the date of sale
to you, repair, replace or refund the retail sales price of said product or any part thereof, at
the option of the Magnadyne Corporation or its authorized agents, if said product or part
is found defective in materials or workmanship, when properly connected and operating
on the correct power requirements designated for the specific product. This warranty and
Magnadyne Corporation or its authorized agent’s obligations hereunder do not apply where
the product was; damaged while in the possession of the consumer, subjected to unrea-
sonable or unintended use, not reasonably maintained, utilized in commercial or industrial
operations, or serviced by anyone other than Magnadyne Corporation or its authorized
agents, or where the warning seal on the product is broken or the power and/or plugs
are detached from the unit. Magnadyne Corporation or any of its authorized agents will
not assume any labor costs for the removal and reinstallation of any product found to be
defective, or the cost of transportation to Magnadyne Corporation or its authorized agents.
Such cost are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in con-
nection with this product, or any damage to recording or recording tape, or any damage
to the products resulting from improper installation, alteration, accident, misuse, abuse or
acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable. Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may have other rights that vary from state to state.
“NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the User’s
authority to operate the equipment.”
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.
Return Authorization must be obtained before sending, or merchandise may be refused.
19
© Copyright 2012
Magnadyne Corporation
M3500DVD-UM
Rev. A 5-14-12
|