RF Output Channel
If channel 3 is already occupied for broadcasting,
ꢀ) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [PLAY B] once.
4) After a few seconds, hold [PLAY B] on the unit for 3 seconds.
• The RF output channel will change to channel 4 from channel 3
and you will see a playback picture.
If you need additional operating assist-
ance after reading this owner’s manual
or to order replacement accessories,
please call
Hint
• The RF output channel
does not change when
you adjust tracking during
playback. In this case, stop
the playback, and start
the playback again. After
that, hold [PLAY B] on the
VCR for 3 seconds again.
Owner’s Manual
TOLL FREE : 1-800-605-8610
Video Cassette Recorder
CMWV405
•
When a picture does not appear on the TV screen, repeat step 4.
5) Press [STOP C] to stop playback.
1. Before Using Your VCR
Stereo TV Connection
VIDEO
IN
AUDIO
IN
You can use the AUDIO OUT jack and
VIDEO OUT jack on the back of the
VCR if your TV has Audio/Video Input
jacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV’s owner’s manual.
ANT
Basic TV Connection
IN
AUDIO
OUT
IN
OUT
Antenna
Antenna
Cable TV
Signal
or
Cable TV
Signal
or
(Back of VCR)
VIDEO
Audio/Video Cables
(not supplied)
ANT
IN
(Back of TV)
(Back of TV)
OUT
VIDEO
IN
AUDIO
IN
ANT
IN
2
(Back of VCR)
(Back of TV)
Disconnect
3
OUT
Connect
Front & Rear Terminals
Connect
AUDIO OUT jack
AUDIO IN jack
RF Cable (supplied)
RF Cable
(not supplied)
RF Cable
(not supplied)
Connect the audio cable here through to the audio
input jack of a camcorder, another VCR, a stereo
amplifier or an audio system.
Connect the audio cable coming from the
audio output jack of a camcorder, another
VCR or an audio source here.
Plug the AC power cords of the VCR and TV into the AC outlets.
4
ANT
ANT IN jack
Connect your antenna or cable box here.
IN
ANT
IN
AUDIO
AUDIO
OUT
IN
OUT
Hint for Cable Box or Satellite Box
ANT OUT jack
OUT
IN
VIDEO
OUT
Connect the supplied RF cable to the
VIDEO
antenna input jack on your TV.
(Back of VCR)
(Cable box or
VIDEO OUT jack
ANT
Antenna or
Cable TV
signal
Satellite box)
IN
Connect the video cable here through the video
input jack of a camcorder, another VCR or a TV.
IN
VIDEO IN jack
O
U
T
E
OUT
RF cable
(supplied)
Connect the video cable coming from the
video output jack of a camcorder, another
VCR or an audio-visual source (laser disc
player, video disc player, etc.) here.
RF Cables
(not supplied)
(Back of TV)
STANDBY-ON
CHANNEL
MENU RECORD
VIDEO
AUDIO
IR
POWER
VCR/TV
CST.IN
TIMER
RECORD
Select this connection when you want to view
or record a scrambled channel. With this con-
nection, channels cannot be changed on the
unit. You can view or record ONLY the chan-
nels you have selected on the cable box or
the satellite box.
(the same channel as the output channel of
the cable box or satellite box).
• If you use the channel 4, you need to
change the unit’s RF output to channel 4.
Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same
channel as you have selected at step ꢀ).
3) On the cable box or satellite box, select the
channel you want to view or record.
• To use the input jacks on the back of this unit, press [0], [0], [1] on the remote control.
• To use the input jacks on the front of this unit, press [0], [0], [2] on the remote control.
Installing the Batteries for
the Remote Control
Supplied Accessory
• Remote control
(NA374UD) with
two AA batteries
• RF cable
• Owner’s manual
•
While you are recording, only the recorded
channel can be viewed.
Install two AA batteries
(supplied) matching
the polarity indicated
on the bottom of the
remote control.
(WPZ090ꢀTM002) (ꢀVMN22462)
Printed in China
ꢀVMN22462 / HJ34RCD ★★★★★
- ꢀ -
EN
3. Preparation for Use
Turn on the Unit for the First Time
To Add/Delete Channels
Clock Set Up
To Select a Channel
MENU
- M E N U -
- M E N U -
1
Turn on the TV and set it
to channel 3.
MENU
1
1
5
6
7
CLOCK SET
You can select a channel by using
the Number buttons on the
remote control.
Notes for using the Number buttons:
• When selecting cable channels
which are higher than 99, enter
channel numbers as a three-digit
number (for example: ꢀꢀ7, press
[1], [1], [7]).
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
MONTH DAY
YEAR
ꢀ 0 0 2 MON 2 0 0 6
/
•
If channel 3 is already occupied
for broadcasting, see “RF Output
Channel” section on page ꢀ.
HOUR MINUTE AM/PM
0 5 – – – –
LANGUAGE SELECT
LANGUAGE SELECT
or
:
or
Select the current hour.
• If the clock is not set,
the CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2.
or
Remote Control TV Screen
STANDBY-ON
2
LANGUAGE SELECT
• You must precede single-digit
channel numbers with a zero (for
example: 02, 03, 04 and so on).
CLOCK SET
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
MONTH DAY
YEAR
ꢀ 0 0 2 MON 2 0 0 6
/
2
3
CHANNEL SET UP
To Preset the Channel Again
HOUR MINUTE AM/PM
0 5 4 0 – –
or
2
3
4
CLOCK SET
or
AUTO SET UP
:
MONTH DAY
ꢀ 0 – –
YEAR
ꢀ) Press [MENU] until the main
menu appears.
B MANUAL SET UP
/
– – – –
or
HOUR MINUTE AM/PM
– – – – – –
Select the current minute.
CLOCK SET
2) Select "CHANNEL SET UP" by
pressing [PLAY B] or [STOP C].
Then, press [F.FWD g].
3) Select "AUTO SET UP" by
pressing [PLAY B] or [STOP C].
Then, press [F.FWD g]. After
scanning, the tuner stops on the
lowest memorized channel.
or
:
Select the current month.
3
CH 0ꢀ
AUTO SET UP
MONTH DAY
YEAR
ꢀ 0 0 2 MON 2 0 0 6
/
MANUAL SET UP
HOUR MINUTE AM/PM
CHANNEL 30 (CATV)
ADD
CLOCK SET
or
0 5
:
4 0
P M AM
B PM
MONTH DAY
ꢀ 0 0 2
YEAR
– – – –
To Change the On-Screen
Language
/
or
Do you connect the cable from the cable box
or the satellite box to the VCR’s ANT-IN jack?
HOUR MINUTE AM/PM
– – – – – –
Select “AM” or “PM”.
or
:
ꢀ) Press [MENU] until the main
menu appears.
Yes
Select the channel to be
added or deleted.
Yes Press [MENU]
to exit.
Select the current day.
2) Select "LANGUAGE SELECT" by
pressing [PLAY B] or [STOP C].
Then, press [F.FWD g].
3) Select "ENGLISH", "FRANCAIS"
or "ESPAÑOL" by pressing
[PLAY B] or [STOP C]. Then,
press [C.RESET/EXIT].
• Refer to “Hint for Cable Box or
8
To exit the
No
Satellite Box” section on page ꢀ.
CLOCK SET screen
4
5
MANUAL SET UP
No Please wait for a few minutes.
CLOCK SET
CHANNEL 30 (CATV)
DELETE
After scanning...
MONTH DAY
ꢀ 0 0 2
YEAR
2 0 0 6
/
• The tuner stops on the lowest memorized
channel.
or
HOUR MINUTE AM/PM
– – – – – –
or
•
You can select only the channels memorized
in the unit by using [CHANNEL ].
:
Hint
Hint
Select “ADD” or “DELETE”.
•
If you accidentally select Spanish
or French and need English: Press
[MENU] and choose SELEC. IDIOMA,
or SELECTION LANGUE. Press
[F.FWD g] and select ENGLISH.
Finally, press [C.RESET/EXIT].
• If "AUTO SET UP" appears on the TV
• To go back one step, press [REW h]
screen again, check the cable connections.
(during steps 2 to 7).
Select the current year.
Then, press [F.FWD g] once again.
• Your clock setting will be lost if either there
is a power failure or if this unit has been
unplugged for more than 30 seconds.
Hint
C.RESET
EXIT
To exit the
menu
•
Repeat these steps only if either there
was a power failure or if this unit has been
unplugged for more than 30 seconds.
- 3 -
EN
4. Precautions
Precautions
Troubleshooting guide
Install Location
For safety and optimum performance of
this unit:
Important Copyright Information
If this unit does not perform properly when operated as instructed in this Owner’s
Manual, check this unit consulting the following checklist.
Unauthorized recording or use of broad-
cast television programming, video tape,
film or other copyrighted material may
violate applicable copyright laws. We
assume no responsibility for the unau-
thorized duplication, use, or other acts
which infringe upon the rights of copy-
right owners.
PROBLEM
CORRECTIVE ACTION
• Install the unit in a horizontal and
stable position. Do not place anything
directly on top of the unit. Do not place
the unit directly on top of the TV.
• Shield it from direct sunlight and keep
it away from sources of intense heat.
Avoid dusty or humid places. Avoid
places with insufficient ventilation for
proper heat dissipation. Do not block
the ventilation holes on the sides of the
unit. Avoid locations subject to strong
vibration or strong magnetic fields.
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
Timer recording is impossible.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
Cannot go into Recording mode. • Make sure the tape has a record tab. If needed, cover the hole with
adhesive tape.
A Note about Recycling
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing
[CHANNEL
].
This product's packaging materials are
recyclable and can be reused. Please
dispose of any materials in accordance
with your local recycling regulations.
Batteries should never be thrown away
or incinerated but disposed of in accord-
ance with your local regulations concern-
ing chemical wastes.
Cannot view a tape but the audio
is OK.
•
Head cleaning may be necessary. Refer to “Auto Head Cleaning” on
page 8.
• Make sure the VCR is not in the Menu mode.
No or poor playback picture.
• Change the RF output channel to CH4. Then select the same
channel on the TV.
Avoid the Hazards of Electrical Shock
and Fire
• Do not handle the power cord with wet
hands.
• Do not pull on the power cord when
disconnecting it from AC wall outlet.
Grasp it by the plug.
• Fine tune your TV.
TV programs cannot be seen
normally.
• Re-check the ANT-IN and ANT-OUT connections. See page ꢀ.
• Press [VCR/TV] on the remote control so that the VCR/TV indicator
on the unit disappears.
No operation from the infrared
Remote Control.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
Note to the Cable TV System Installer
This reminder is provided to call the
Cable TV system installer’s attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and
in particular, specifies that the cable
ground should be connected to the
grounding system of the building, as
close to the point of cable entry as pos-
sible.
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing
making a copy of a video tape.
copy guard protection.
Moisture Condensation Warning
Specifications
Moisture condensation may occur inside
the unit when it is moved from a cold
place to a warm place, or after heating
a cold room or under conditions of high
humidity. Do not use the unit at least for
2 hours until its inside is dry.
Video Heads :
Operating temperature : 4ꢀ°F~ꢀ04°F
(5°C~40°C)
Four Heads
Power requirement : ꢀ20V, 60Hz
Power consumption : ꢀ4 Watts
Dimensions :
W ꢀ4-3/ꢀ6" (360mm)
Converter output :
VHF Channel 3 or 4
H 3-5/8" (92mm)
D 8-9/ꢀ6" (2ꢀ6mm)
4.0 lbs. (ꢀ.8 Kg.)
(approx.)
Weight :
CAUTION:
FCC Warning
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUg TO
WIDE SLOT, FULLY INSERT.
• Designs and specifications are subject to change without notice and legal obligation.
• If there is a discrepancy between languages, the default language will be English.
This equipment may generate or use
radio frequency energy. Changes or
modifications to this equipment may
cause harmful interference unless the
modifications are expressly approved in
the instruction manual. The user could
lose the authority to operate this equip-
ment if an unauthorized change or modi-
fication is made.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or
special waste. Contact your council for details.
- 4 -
EN
5. Playback
Turn on the TV and set it to
channel 3.
7. Other Operations
To cue or review picture during
playback (Picture Search)
To play back in slow motion
Before:
STANDBY-ON
CHANNEL
Press [SLOW] during playback or the still mode.
• If the noise bar appears on the TV
screen, you can reduce it by pressing
VCR/TV
3
EJECT
1
Press [F.FWD g] or [REW h].
• Press it again and the VCR will now
search in super high speed (in the LP/
SLP modes only).
4
3
• If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
2
[CHANNEL
].
4
5
8
6
PLAY
REW
F.FWD
STOP/EJECT
SEARCH
-MODE
CHANNEL
MENU RECORD
7
9
To temporarily stop recording
2
1
IR
Remote Control TV Screen
POWER
VCR/TV
CST.IN
TIMER
RECORD
C.RESET
EXIT
To freeze the picture on TV screen (Pause mode)
during playback (Still mode)
MENU
0
SLOW
PAUSE
/STILL
RECORD
SPEED
DISPLAY
Press [PAUSE/STILL].
PLAY
B
• During the rec pause mode, five
C
Press [PAUSE/STILL]. Each time you
press the button, the picture will be for-
warded by one frame.
• If the picture begins to vibrate vertically
during the still mode, stabilize the pic-
3
4
marks appear on the TV screen. Each
mark represents one minute.
C
POWER
VCR/TV
CST.IN
2
1
2
• Press it again to resume recording.
Hint
3
4
Auto Rewind
When a tape reaches its end during play-
back, fast-forward, or recording (except
timer recording and One Touch Recording),
the tape will automatically rewind to the
beginning. After rewinding finishes, the unit
will eject the tape and turn itself to off.
ture by pressing [CHANNEL
].
EJECT
• When a tape without record tab is inserted, the unit will start playback
automatically at step ꢀ.
• Tracking will be automatically adjusted upon playback. To adjust the
tracking manually, press [CHANNEL
• If the picture is distorted or rolling verti-
cally, adjust the vertical hold control on
your TV if equipped.
STOP
EJECT
A
].
Counter Reset
Press [C.RESET/EXIT].
Hint
6. Recording & OTR (One Touch Recording)
Before:
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to
the tape and the video head.
Turn on the TV and set it to
channel 3.
2
• To return to playback from the Picture Search/Still/Slow mode, press [PLAY B].
•
If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
STANDBY-ON
VCR/TV
3
EJECT
1
8. On-Screen Operations
6
Remote Control TV Screen
1
2
1
4
7
2
with tab
CHANNEL
4
5
8
6
1
2
3
4
To call up the main menu
2
5
8
0
3
6
9
PLAY
SEARCH
-MODE
REW
F.FWD
CHANNEL
STOP/EJECT
CHANNEL
MENU RECORD
7
9
CHꢀ2
MENU
- M E N U -
IR
C.RESET
EXIT
POWER
VCR/TV
CST.IN
TIMER
RECORD
MENU
0
SLOW
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
POWER
VCR/TV
CST.IN
Select the chan-
nel to record.
PAUSE
/STILL
PLAY
REW
F.FWD
RECORD
STOP/EJECT
SPEED
DISPLAY
MENU RECORD
4
3
5
IR
POWER
VCR/TV
CST.IN
TIMER
RECORD
LANGUAGE SELECT
Select the desired tape
speed.
3
SP
SPEED
5
6
To select an item
Tape Speed
Recording/Playback Time
1
2
Type of tape
SP mode
SLP mode
T60
T120
2hours
6hour
T160
2-2/3hours
8hour
4
- M E N U -
1
4
2 3
1hour
3hour
or
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
RECORD
4
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record tab.
To record on it later, cover the hole with
adhesive tape.
LANGUAGE SELECT
STANDBY-ON
RECORD
REC
VCR/TV
3
EJECT
1
To decide
2
Press [RECORD] repeatedly to select the
desired recording length.
CHANNEL
Record tab
CHANNEL SET UP
4
5
8
6
SEARCH
-MODE
REC
OTR(0:30)
OTR(ꢀ:00).....
7
9
AUTO SET UP
(Normal recording)
C.RESET
EXIT
B MANUAL SET UP
MENU
0
SLOW
OTR(8:00)
OTR(7:30)
4 1
2
4
3
PAUSE
/STILL
RECORD
SPEED
DISPLAY
EJECT
5
6
Hint
To exit the menu
STOP
EJECT
A
C.RESET
EXIT
MENU
• If you have connected this unit to a cable box or satellite box, refer to
“Hint for Cable Box or Satellite Box” section on page ꢀ.
or
- 5 -
EN
9. Recording Features
Timer Recording
Hints for Timer Recording
•Insert a tape with its record tab into the unit.
• If there is a power failure or the unit has been unplugged for more than 30 sec-
onds, the clock setting and all timer settings will be lost.
• If the tape runs out before the end time, the unit will switch to the Stop mode
immediately, eject the tape and the power will be turned off. The TIMER indicator
will flash.
- M E N U -
ONE TIME PROGRAM
PROGRAM NUMBER
1
5
Select the desired start
time (hour).
9
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
ꢀ
MENU
DATE
ꢀ 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
ONE TIME PROGRAM
or
• If a tape is not in the unit or does not have the record tab, the TIMER indicator
flashes and timer recording cannot be performed. Please insert a recordable tape.
• When all the Timer Recording are completed, the TIMER indicator flashes.
To play or eject the recorded tape, press [STANDBY-ON] first, and then
PROGRAM NUMBER
DATE ꢀ 0 / 2 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
ꢀ
LANGUAGE SELECT
or
CHANNEL
ꢀ 6
REC SPEED SP
B SP
SLP
CHANNEL
– –
Select the desired recording speed.
REC SPEED – –
press [PLAY
B] or [EJECT
A].
C.RESET
EXIT
Select the
minute.
To cancel a Timer Recording that is in progress
Press [STOP/EJECT ] on the unit.
P
N
2
PROGRAM NUMBER
DATE – – / – –
ꢀ
or
STANDBY-ON
10
Turn off the
VCR for
recording.
Copying a Video Tape
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL
REC SPEED – –
– –
Warning: Unauthorized recordings of copyrighted video tapes
or
may be an infringement of copyright laws.
(Back of TV)
•
TIMER indicator on the VCR lights up.
Select an empty program
number.
(Back of Playing VCR)
(Back of Recording VCR*)
Hint
ONE TIME PROGRAM
PROGRAM NUMBER
6
• To go back one step, press
[REW h] (during steps 3 to 9).
ANT
IN
ꢀ
2
AUDIO
OUIN
VIDEO
DATE
ꢀ 0 / 2 3 MON
OUT
OUT
1
Connect
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
OUT
IN
IN
Connect
or
To Check, Correct, or Cancel
a Timer Program
VIDEO
AUDIO
CHANNEL
REC SPEED – –
– –
3
4
PROGRAM NUMBER
ꢀ
AM
RF Cable
(supplied)
B ONCE
DAILY
WEEKLY
B PM
ꢀ) Turn the power on by pressing
[STANDBY-ON].
Audio/Video Cables
(not supplied)
Select “AM” or “PM”.
*Front input jacks are also available
or
ꢀ) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its record tab into the recording VCR.
2) Select main menu by pressing
[MENU].
Select “ONCE”, “DAILY”
(Mon-Fri), or “WEEKLY”.
3) Select "TIMER PROGRAMMING" by
3) Press [SPEED] on the remote control of the recording VCR to select
7
8
Repeat the procedure in steps
5 and 6 to set the end time.
pressing [PLAY B] or [STOP C]
.
the desired recording speed (SP/SLP).
Then, press [F.FWD g]
.
4) Select the “Lꢀ” or “L2” position on the recording VCR.
4) Select the program number
which you want to check by
pressing [PLAY B] or
• To use the input jacks on the back of this unit, select "Lꢀ" position by
Select the desired month.
pressing [0], [0], [1] on the remote control or [CHANNEL
].
ONE TIME PROGRAM
[STOP C]. The details of the
program you selected will
appear on the TV screen.
• Go to the digit you want to
change by pressing
[F.FWD g] or [REW h].
Then, enter correct numbers by
pressing [PLAY B] or
PROGRAM NUMBER
DATE ꢀ 0 / 0 2 MON
START TIME – – : – – – –
END TIME – – : – – – –
ꢀ
ONE TIME PROGRAM
• To use the input jacks on the front of this unit, select "L2" position by
or
PROGRAM NUMBER
DATE ꢀ 0 / 2 3 MON
START TIME 0 7 : 3 0
END TIME 0 8 : 3 0
ꢀ
pressing [0], [0], [2] on the remote control or [CHANNEL
5) Press [RECORD] on the recording VCR.
].
PM
PM
CHANNEL
REC SPEED – –
– –
or
6) Begin playback of the tape in the playing VCR.
CHANNEL
ꢀ 6
REC SPEED – –
7) To stop recording, press [STOP/EJECT
P
N] on the recording VCR,
then stop playback of the tape in the playing VCR.
Select the desired day.
Select the desired channel.
•
If you have connected the unit to a cable
box or satellite box as the Connection on
page ꢀ, select the VCR to channel 3 or 4
(the RF output channel of the VCR). Then,
select the desired channel at the cable
box or satellite box. Leave the cable box
or satellite box on for timer recording.
Hint
[STOP C].
• You can program one
year in advance.
or
• For best results during dubbing, use the VCR’s front panel controls whenever possible. The
remote control might affect the playing VCR’s operation.
•
You may cancel the entire
program by pressing [REW h]
while the program number flashes.
5) Press [C.RESET/EXIT] to exit.
6) Press [STANDBY-ON] to return
to timer stand-by mode.
• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are
not recommended.
•
You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs.
• “Lꢀ” or “L2” is found before the lowest memorized channel. (Example: CH02)
• "L2" input jacks are on the front of this unit.
- 6 -
EN
10. Special Features
Time Search
Index Search
Auto Repeat
You can search backward and
forward a specific length of
time on a tape.
This function will playback a
tape repeatedly from the begin-
ning when the tape reaches to
the end.
You can skip the program backward
and forward by the Index Mark.
• Insert a tape into this unit.
• Insert a tape into this unit.
1
INDEX SEARCH
SEARCH
-MODE
• Insert a tape into this unit.
1
– –
TIME SEARCH
SEARCH
-MODE
MENU
– : – –
- M E N U -
1
TIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
Press once.
LANGUAGE SELECT
Press twice.
or
2
INDEX SEARCH
2
Select the desired length
of time for fast forwarding
or rewinding.
0 3
or
TIME SEARCH
2 : 5 0
- M E N U -
2
0ꢀ ~ 20
CURRENT PROGRAM
Beginning
of tape
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
End
or
of tape
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
02 01 01 02 03
INDEX MARK
LANGUAGE SELECT
0:0ꢀ~ 9:59
(ꢀ minute~9 hours
and 59 minutes)
To rewind To fast forward
3
4
3
AUTO REPEAT
B
To rewind
To fast forward
After searching,
3
4
Hint
After searching,
• To cancel Auto Repeat, follow steps ꢀ-2
above. Then, press [F.FWD g] so that
[OFF] appears beside AUTO REPEAT.
Press [C.RESET/EXIT] to exit.
PLAYB
• If menu remains on the TV screen at step
3), press [C.RESET/EXIT] to exit.
Hint
PLAYB
• The unit records an index mark at the
beginning of the recording when you make
a recording. There should be time gap
between index marks for the Index Search.
Hints for Index Search & Time Search
• These functions are not available during recording.
• Press [STOP C] to stop the search.
• If the end of the tape is reached during a Search, the VCR will cancel the search
and rewind the tape.
- 7 -
EN
11. Information
Maintenance
Servicing
Auto Head Cleaning
LIMITED WARRANTY
If this unit become inoperative, do not try to
correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug
the power plug, and please call our help line
mentioned on page ꢀ to locate an Authorized
Service Center.
• This unit automatically cleans video heads
as you insert or remove a cassette, so you
can see a clearer picture.
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship as
follows :
• Playback picture may become blurred or
interrupted while the TV program recep-
tion is clear. Dirt accumulated on the video
heads after long periods of use, or the usage
of rental or worn tapes can cause this prob-
lem. If a streaky or snowy picture appears
during playback, the video heads in your
VCR may need to be cleaned.
ꢀ. Please visit your local Audio/Video store
and purchase a good quality VHS Video
Head Cleaner.
2. If a Video Head Cleaner does not solve
the problem, please call our help line men-
tioned on page ꢀ to locate an Authorized
Service Center.
DURATION :
PARTS :
LABOR :
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts are excluded from this warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the
date of original retail purchase.
Cabinet Cleaning
• Wipe the front panel and other exterior sur-
faces of the VCR with a soft cloth immersed
in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray
insecticide liquid near the VCR. Such chemi-
cals may cause damage and discoloration to
the exposed surfaces.
LIMITS AND EXCLUSIONS :
ThIs wARRANTy Is exTeNDeD ONly TO The ORIgINAl ReTAIl PURChAseR. A PURChAse ReCeIPT OR OTheR
PROOF OF ORIgINAl ReTAIl PURChAse wIll be ReqUIReD TOgeTheR wITh The PRODUCT TO ObTAIN seRv-
ICe UNDeR ThIs wARRANTy.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by AN UNAUThORIZeD seRvICe CeNTeR. This limited warranty does not apply to any
product not purchased and used in CANADA.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this prod-
uct or damage which results from fire, flood, lightning or other acts of god.
NOTES:
• Remember to read the instructions included
with the video head cleaner before use.
• Clean video heads only when problems
occur.
ThIs wARRANTy DOes NOT COveR PACKINg MATeRIAls, ANy ACCessORIes (exCePT ReMOTe CONTROl),
ANy COsMeTIC PARTs, COMPleTe AsseMbly PARTs, DeMO OR FlOOR MODels.
FUNAI CORP. AND ITs RePReseNTATIves OR AgeNTs shAll IN NO eveNT be lIAble FOR ANy geNeRAl,
INDIReCT OR CONseqUeNTIAl DAMAges ARIsINg OUT OF OR OCCAsIONeD by The Use OF OR The INAbIlITy
TO Use ThIs PRODUCT. ThIs wARRANTy Is MADe IN lIeU OF All OTheR wARRANTIes, exPRess OR
IMPlIeD, AND OF All OTheR lIAbIlITIes ON The PART OF FUNAI, All OTheR wARRANTIes INClUDINg The
wARRANTy OF MeRChANTAbIlITy AND FITNess FOR A PARTICUlAR PURPOse, ARe heReby DIsClAIMeD by
FUNAI AND ITs RePReseNTATIves IN CANADA.
All wARRANTy INsPeCTIONs AND RePAIRs MUsT be PeRFORMeD by AN AUThORIZeD seRvICe CeNTeR.
ThIs wARRANTy Is ONly vAlID wheN The UNIT Is CARRIeD-IN TO AN AUThORIZeD seRvICe CeNTeR.
The PRODUCT MUsT be ACCOMPANIeD by A COPy OF The ORIgINAl ReTAIl PURChAse ReCeIPT. IF NO
PROOF OF PURChAse Is ATTACheD, The wARRANTy wIll NOT be hONOReD AND RePAIRs COsTs wIll be
ChARgeD.
ATTENTION :
FUNAI CORP. ReseRves The RIghT TO MODIFy ANy DesIgN OF ThIs PRODUCT wIThOUT PRIOR
NOTICe.
To locate your nearest AUThORIZeD seRvICe CeNTeR or for general service inquiries, please contact us at :
FUNAI CORPORATION
Customer Service
Tel: 1-800-605-8610
ꢀ9900 Van Ness Avenue, Torrance, CA 9050ꢀ
- 8 -
EN
|