INSTALLATION INSTRUCTIONS FOR PART 99-7335S
HYUANPDPALIICAVTeIOrNaScruz
2007-2010
Automatic climate control only
99-7335S
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted to match factory dash-”S”=Silver
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
A
C
D
E
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 - KIA/Hyundai harness 2004-up
• 70-7303 - KIA/Hyundai harness 2009
Antenna Adapter:
• 40-KI11 - KIA antenna adapter 2007-up
F
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
95-7335S DASH DISASSEMBLY
HYUNDAI VERACRUZ 2007-2010
A
1
2
3
4
Disconnect the negative battery
terminal to prevent an accidental short
circuit.
Unclip and remove the side trim
panels. (Tip: start at the bottom of the
panels) (Figure A)
Remove (6) Phillips head screws
securing the radio trim panel and
remove trim panel. (Figure B)
Remove (4) Phillips screws securing
the climate control, (2) Phillips screws
securing the clock display and (4)
Phillips screws securing the pocket
from the radio trim panel. (Figure C)
B
Continue to kit preparartion.
C
CLOCK DISPLAY-REAR VIEW
RADIO HOUSING
REAR VIEW
CLIMATE CONTROL-REAR VIEW
POCKET-REAR VIEW
1
99-7335S KIT ASSEMBLY
KIT PREPARATION
Attach the climate control, pocket and the clock display into the 99-7335S radio
1
housing using the factory hardware. (Figure A)
Continue to kit assembly.
A
2
99-7335S KIT ASSEMBLY
DIN MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
2
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
3
Snap the pocket into the bottom
opening of the radio housing.
B
(Figure B)
4
5
Slide the aftermarket head unit into
the cage and secure. (Figure C)
Reassemble dash in reverse order of
disassembly.
C
3
99-7335S KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
2
3
4
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
B
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
5
6
Snap the Trim plate into the Radio
Housing. (Figure C)
Reassemble dash in reverse order of
disassembly.
C
4
99-7335S KIT ASSEMBLY
DOUBLE DIN/STACKED ISO MOUNT
UNITS RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2
3
Cut and remove the center bar from
the radio housing. (Figure A)
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Figure B)
B
4
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio. (Figure C)
C
5
6
Snap the Double DIN trim plate into the
Radio Housing. (Figure C)
Reassemble dash in reverse order of
disassembly.
5
99-7335S INSTRUCTIONS
1-800-221-0932
REV. 09/02/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST99-7335S
|