INST 7500
KIT COMPONENTS
6
#1
Fig. A
Fig. C
99-7500
DW-7501
INSTALLATION
INSTRUCTIONS
ng #2
rimplate
r Bar
APPLICATIONS
Fig. B
CAR
MAZDA
PAGE
Fig. E
323 1986-89*...............................................................................1
323 1990-94*...............................................................................1
626 (models w/factory receiver/tape deck/eq/pocket) 1986-92....2
626 (models w/factory receiver/pocket) 1986-92* ...................... 2
929 1988-91.................................................................................3
B-Series Pickup 1986-93................................................................3
Miata 1990-99.............................................................................. 4
MPV 1989-95*.............................................................................. 4
MX6 (models w/factory receiver/tape deck/eq/pocket) 1986-92...2
MX6 (models w/factory receiver/pocket) 1986-92*....................... 2
Protege 1990-94*......................................................................... 1
RX-7 1986-91............................................................................... 5
(8) 3/8" Phillips
Screws
Fig. D
(6) ¾" Hex-head Screws
(6) 3/8" Hex-head Screws
(4) ½" Hex-head
Screws
B-SERIES PICKUP: Re-connect the battery terminal and test the unit for proper operation.
Mount Bracket Set #1 to the Housing with (4) ½" Hex-head Screws supplied. Mount the
head unit/kit assembly to the back of the dash trim bezel with (4) screws removed in step #1
and re-attach the bezel. (see Fig. A)
Bracket Set #1
Equalizer
Dummy
Plate
323 1986-89, 626 / MX6 (models using Radio Housing #2): Re-connect the battery terminal
and test the unit for proper operation. Mount the head unit/kit assembly to the back of the dash
trim bezel with(4) 3/8" Phillips Screwssupplied and re-attach the bezel. (see Fig. B)
* For aftermarket DIN head unit installations, order Metra's 99-7501
For models with pockets 3¾" or taller, order Metra's 99-7501
TOOLS REQUIRED
626 / MX6 (models using Radio Housing #1: Re-connect the battery terminal and test the
unit for proper operation. Mount the head unit/kit assembly to the back of the dash trim bezel
with(8) 3/8" Phillips Screwssupplied and re-attach the bezel. (see Fig. C)
Phillips screwdriver
323 1990-94, MPV, PROTEGE: Re-connect the battery terminal and test the unit for proper
operation. Mount the head unit/kit assembly to the sub-dash with (4) ¾" Hex-head Screws
supplied. (see Fig. D)
929, MIATA, RX-7: Re-connect the battery terminal and test the unit for proper operation.
Mount the head unit/kit assembly to the back of the dash trim bezel with (6) 3/8" Hex-head
Screwssupplied and re-attach the bezel. (see Fig. E)
Cutting tool
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
rev. 300801
Socket wrench
7
MAZDA RX-7 1986-91
MAZDA 626 / MX6 1986-92
(models equipped with factory receiver/pocket)
1
2
"A"
1
2
"A"
"A"
A"
"E"
"E"
"A"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed in the
ashtray cavity. Unsnap the gear shifter trim
and remove (2) screws exposed. Unsnap
the climate control trim bezel and remove (2)
screws exposed. Remove the dash trim
bezel and disconnect the wiring. Remove
(4) screws securing the factory head unit
anddisconnectthewiring.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "A".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
The
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
anddiscardtheplate.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
The
MAZDA 626 / MX6 1986-92
(models equipped with factory receiver/tape deck/eq/pocket)
ALL VEHICLES
"B"
1
2
"B"
"B"
3a
"B"
"B"
Fig. A
"B"
"B"
"B"
Fig. B
Disconnect the negative battery terminal to
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "B". The
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed.
Remove the pocket and (2) screws exposed.
Remove the radio trim bezel and disconnect
the wiring. Remove (4) screws securing the
factory dummy plate to the back of the bezel
anddiscardtheplate.
2-SHAFT HEAD UNITS: For models using Radio Housing #1, attach the Faceplate to the
Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A).
For models using Radio Housing #2, slide the aftermarket head unit into the kit and secure
withshaftnuts. (seeFig. B)
5
2
MAZDA 929 1988-91
MAZDA Miata 1990-99
1
2
1
2
"A"
"A"
"A"
"A"
"A"
"A"
A"
A"
"A"
"A"
"A"
"A"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Reach
behind the console and remove (2) nuts
supporting the head unit carrier. Remove
the factory head unit and disconnect the
wiring..
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "A".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from the center console storage
compartment. Remove (1) screw under the
ashtray. Remove (1) screw from each side
of the center console panel and remove the
panel. Remove (1) screw exposed at the
base of the dash trim bezel. Pop out the a/c
vents and remove (2) screws exposed.
Remove the dash trim bezel.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "A".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
The
The
MAZDA B-Series Pickup 1986-93
1
2
MAZDA MPV 1989-95
"C"
1
2
"C"
"E"
"E"
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(2) screws from each side of the radio trim
bezel. Remove the ashtray and (1) screw
from the rear support tab. Remove the radio
trim bezel/sub-bracket assembly. Remove
(4) screws securing the sub-bracket to the
back of the radio trim bezel. Loosen (2)
screws on top of the bezel and remove the
sub-bracketfromthebezel.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "C".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
The
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray and (2) screws exposed in the
ashtray cavity. Remove the radio trim bezel
and disconnect the wiring. Remove (4)
screws securing the factory head unit and
disconnectthewiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E".
mounting tabs can be identified by the
stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLESonPage#5.
The
3
4
|