MTX Audio Speaker 620WE User Manual

21A3087  
FIRST  
CLASS  
STAMP  
HERE  
MODEL 620WE  
IN-WALL ENCLOSED LOUDSPEAKER  
OWNERS MANUAL  
4545 E BASELINE RD  
PHOENIX AZ 85040-6400  
 
OTHER HOME AUDIO PRODUCTS FROM MTX  
LOUDSPEAKER PLACEMENT  
MTX offers a wide assortment of audio components. Ranging from  
in-ceiling speakers to amplifiers to accessories. Each component  
is value engineered and must meet strict quality control standards  
before it becomes part of the MTX product line.  
Blueprint Series Loudspeakers are designed to work within any interior  
decorating scheme. They can be installed in virtually any location where  
flush mounting is possible. To maximize their sound performance however  
certain guidelines should be followed. For the best stereo reproduction the  
two loudspeakers should be placed an equal distance from your listening  
position and separated so that the angle between them, at the listening  
position, is between 40 and 60 degrees.  
Listed below you will find a sampling of components available  
from your authorized MTX dealer.  
LPS-600  
Speaker/Amplifier Selector  
Accommodates up to 6 pair of speakers  
Handles up to 250 watts/channel continuous (RMS)  
Impedance Protection Circuitry  
Accommodates up to 14 gauge wire  
MODEL MP42  
Multi-Purpose Loudspeaker  
Two 4” Woofers, with 1/2” Balanced Dome Tweeter  
50 Watts RMS/200 Watts Total Power Handling  
Magnetically shielded, weather resistant  
Sleek, Euro-style design  
For best stereo imaging, we recommend that the units be placed so that  
the tweeters are as close as possible to the ear level of a seated listener.  
As this is not always possible in keeping with aesthetic design of a  
particular room, the Model 620WE loudspeaker is designed with a pivoting  
tweeter which rotates to allow you to “aim” the high frequencies toward  
the listening position.  
Available in white or black  
12.6” x 4.8” x 4.9”  
PS15  
15” Powered Subwoofer System  
200 Watt Class D Switching Power Amplifier  
Infrared Remote Control for Volume Function  
Magnetically Shielded, Downfiring Subwoofer in small enclosure  
Signal Sensing Auto Turn On  
Red LED Clipping Indicator  
Speaker and Line Level Inputs  
Continuously variable 50Hz to 150Hz, 24dB/Octave Crossover  
Frequency Response 30Hz - 150Hz  
17.2” H x 17” W x 20.25” D  
Normal Dispersion  
Dispersion After Tweeter Adjustment  
 
STEP 1  
STEP 4  
Using a stud finder (available at low cost at most hardware stores)  
or other accurate method, locate center point between two  
studs and mark. Using template provided, trace hole pattern on  
surface of wall.  
Attach loudspeakers wires to speaker terminals, observing correct  
polarity (positive to positive and negative to negative). Insert the  
speaker into the mounting hole. Be careful not to pinch the  
loudspeaker wires in the process. using the integral bubble levels  
located on the baffle, align the speaker’s frame either horizontally  
or vertically. Once you are satisfied with the speaker’s location,  
tighten the eight mounting wings located near each corner of  
the frame using a phillips screwdriver. The mounting wings are  
designed to swing into position when you start tightening. Note:  
the phillips head screws are for tightening the mounting wings.  
The torx head screws are for the enclosure which should not be  
tightened or loosened.  
STEP 2  
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole  
in wall, following traced pattern.  
STEP 5  
After speaker panel is secured tightly, test for sound.  
STEP 3  
STEP 6  
Run loudspeaker wires to sound source location. There are several  
methods you can use to accomplish wiring, depending on the  
construction characteristics of the room or house. You can add a  
professional touch to your installation by using a speaker terminal  
plate at the source location. Leave sufficient amount of wire at  
speaker location (8 to 10 inches) to complete connection.  
When you are satisfied the speaker is operational, “aim” the  
tweeter, and affix grill. As grill is designed for a snug fit, you’ll need  
to position one edge into the slot first, and press or squeeze  
around perimeter of thegrill, while pushing the leading edge into  
the grill slot.  
 

Miele Food Warmer EGW4060 14 User Manual
Napoleon Grills Outdoor Fireplace GD33NR User Manual
National Instruments Computer Hardware NI PXI PCI 5114 User Manual
NEC DVD Recorder NDRV 60 User Manual
Netac Tech Portable Multimedia Player Netac Tech Co Ltd User Manual
Newcon Optik Binoculars NV66 G2 User Manual
Nikon Camera Accessories MB D100 User Manual
Northern Industrial Tools Air Compressor 45929 User Manual
Panasonic All in One Printer KX FT33HK User Manual
Patton electronic Network Card 2020P User Manual