Operating and installation instructions
Refrigerator with Dynamic cooling
K 11820 SD
K 12820 SD
K 12820 SD edt/cs
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 09 434 270
Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Side-by-side installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Levelling the appliance door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Changing the door hinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Aligning the appliance door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Building in the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Guide to the appliance
aOn/Off button
dSuper cool button and
indicator light
bTemperature selector button
cTemperature display
eDynamic cooling button and
indicator light
4
Guide to the appliance
aDynamic cooling fan
bButter and cheese compartment
cEgg tray
dAdjustable shelves
eBottle rack
fBottle shelf
gCondensate channel and
drain hole
hFruit and vegetable containers
5
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
6
Warning and Safety instructions
This appliance complies with all relevant safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
before using it for the first time. They contain important
information on its safety, installation, use and maintenance. Miele
cannot be held liable for damage caused by non-compliance with
these Warning and Safety instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
The appliance is not designed for commercial use. It is intended
~
for use in domestic households and similar working and residential
environments.
This appliance is not intended for outdoor use.
The appliance is intended for domestic use only for the cool
~
storage of food and drink.
Any other usage is not supported by the manufacturer and could be
dangerous.
7
Warning and Safety instructions
The appliance is not suitable for storing and keeping cool
~
medicines, blood plasma, laboratory preparations or other such
materials or products. Incorrect use of the appliance for such
purposes can cause deterioration of the items stored. The appliance
is not suitable for use in areas where there is a risk of explosion.
Miele cannot be held liable for damage resulting from incorrect or
improper use or operation.
The appliance can only be used by people with reduced
~
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and understand the hazards
involved.
Safety with children
Children under 8 years of age must be kept away from the
~
appliance unless they are constantly supervised.
Children 8 years and older may only use the appliance without
~
supervision if they have been shown how to use it in a safe way and
understand the hazards involved.
Children must not be allowed to clean or maintain the appliance
~
unsupervised.
This appliance is not a toy! To prevent the risk of injury, do not
~
allow children to play with it or use the controls. Please supervise
children whilst you are using the appliance.
8
Warning and Safety instructions
Danger of suffocation. Packaging, e.g. cling film, polystyrene and
~
plastic wrappings, must be kept out of the reach of babies and
children. Whilst playing, children could become entangled in
packaging or pull it over their head and suffocate.
Technical safety
The coolant system is tested for leaks. The appliance complies
~
with the relevant safety requirements and the appropriate EU
guidelines.
This appliance contains the coolant Isobutane (R600a), a natural
~
gas which is environmentally friendly. Although it is flammable, it
does not damage the ozone layer and does not increase the
greenhouse effect.
The use of this coolant has, however, led to a slight increase in the
noise level of the appliance. In addition to the noise of the
compressor, you might be able to hear the coolant flowing around
the system. This is unavoidable, and does not have any adverse
effect on the performance of the appliance.
Care must be taken during the transportation and installation of the
appliance that no parts of the cooling system are damaged. Leaking
refrigerant can damage the eyes.
In the event of any damage:
– avoid any flames or anything which creates a spark,
– disconnect the appliance from the electricity supply.
– ventilate the room where the appliance is located for several
minutes, and
– call the Service department.
9
Warning and Safety instructions
The more coolant there is in an appliance, the larger the room it
~
should be installed in. In the event of a leakage, if the appliance is in
a small room, there is the danger of combustible gases building up.
For every 8 g of coolant at least 1 m3 of room space is required. The
amount of coolant in the appliance is stated on the data plate inside
the appliance.
To avoid the risk of damage to the appliance, make sure that the
~
connection data (fuse rating, frequency and voltage) on the data
plate corresponds to the household supply before connecting the
appliance to the mains supply. Check that this is the case before
connecting the appliance. Consult a qualified electrician if in any
doubt.
The electrical safety of this appliance can only be guaranteed
~
when it is correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested and where there is any
doubt, the household wiring system should be inspected by a
qualified electrician.
If the electrical connection cable is faulty it must only be replaced
~
by a Miele approved service technician to protect the user from
danger.
Do not connect the appliance to the mains electricity supply by a
~
multi-socket adaptor or extension lead . These are a fire hazard and
do not guarantee the required safety of the appliance.
Do not use in a damp environment (e.g. garage or utility room).
~
Moisture could reach live components or the electrical connection
and cause a short circuit.
This appliance must not be used in a non-stationary location (e.g.
~
on a ship).
10
Warning and Safety instructions
A damaged appliance can be dangerous. Check the appliance
~
for visible signs of damage. Do not use a damaged appliance.
The appliance must be disconnected from the mains electricity
~
supply during installation, maintenance and repair work. Ensure that
power is not supplied to the appliance until after it has been
installed or until after any maintenance or repair work has been
carried out.
Installation, maintenance and repairs may only be carried out by
~
a suitably qualified and competent person in strict accordance with
national and local safety regulations.
While the appliance is under guarantee, repairs should only be
~
undertaken by a service technician authorised by Miele. Otherwise
the guarantee is invalidated.
The manufacturer can only guarantee the safety of the appliance
~
when original Miele replacement parts are used. Faulty components
must only be replaced by genuine Miele original spare parts.
In areas which may be subject to infestation by cockroaches or
~
other vermin, pay particular attention to keeping the appliance and
its surroundings clean at all times. Any damage caused by
cockroaches or other vermin will not be covered by the guarantee.
Correct use
The appliance is designed for use within certain climate ranges
~
(ambient temperatures), and should not be used outside this range.
The climate range of the appliance is stated on the data plate inside
the appliance. Installing it in a room with too low an ambient
temperature will lead to the appliance switching off for longer
periods so that it cannot maintain the required temperature.
11
Warning and Safety instructions
Do not cover or block the air vents as this could impair the
~
efficiency of the appliance, increase the electricity consumption and
could cause damage to the appliance.
If storing food which contains a lot of fat or oil, make sure that it
~
does not come into contact with plastic components as this could
cause stress cracks or break the plastic.
Do not store explosive materials in the appliance or any products
~
containing propellants (e.g. spray cans). Thermostats switching on
may produce sparks which could present a fire hazard. Flammable
compounds could explode.
Do not operate any electrical equipment (e.g. an electric
~
ice-cream maker) inside the appliance. Danger of sparking and
explosion.
If storing alcohol with a high percentage proof, make sure it is
~
tightly closed and stored upright.
Observe the manufacturer's "use-by" dates and storage
~
instructions given on food to avoid the risk of food poisoning.
Storage times will depend on several factors, including the
freshness and quality of the food as well as the temperature at which
it is stored.
Only use genuine original Miele accessories with this appliance.
~
Using spare parts or accessories from other manufacturers will
invalidate the guarantee, and Miele cannot accept liability.
12
Warning and Safety instructions
Stainless steel appliances
Do not use sticky notes, transparent adhesive tape, masking tape
~
or other types of adhesive on the surface of the door. These
damage the surface, causing it to lose its dirt-repellent protective
coating.
The high-quality surface of the door is susceptible to scratching.
~
Even fridge magnets can cause scratching.
Cleaning and care
Do not use any oils or grease on the door seal, as these will
~
cause the seal to deteriorate and become porous with time.
Danger of injury.
~
Do not use a steam cleaning appliance to clean this appliance. The
steam could reach electrical components and cause a short circuit.
Do not use sharp edged objects to
~
– remove frost and ice,
– lift food.
They will damage the evaporator, causing irreversible damage to
the appliance.
Never place electric heaters or candles in the appliance to
~
defrost it. These can damage the plastic parts.
Do not use defrosting sprays or de-icers, as they could contain
~
substances which could damage the plastic parts and which may
cause the build up of gases and pose a danger to health.
13
Warning and Safety instructions
Disposal of your old appliance
Before disposing of an old appliance, first make the door latch or
~
lock unusable.
This way you will prevent children from accidentally locking
themselves in and endangering their lives.
Be careful not to damage any part of the pipework whilst awaiting
~
disposal, e.g. by
– puncturing the refrigerant channels in the evaporator.
– bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the eyes.
14
How to save energy
Normal energy
consumption
Increased energy
consumption
Installation site
In a ventilated room.
In an enclosed, unventilated
room.
Protected from direct
sunlight.
In direct sunlight.
Not near to a heat source
(radiator, oven).
Near to a heat source
(radiator, oven).
Where the ideal ambient room Where there is a high
temperature is approx. 20°C. ambient room temperature.
Ventilation gaps uncovered Ventilation gaps covered up
and dusted regularly.
or dusty.
Compressor and metal grille Dust build-up on the
(heat exchanger) dusted at compressor and metal grille
least once a year. (heat exchanger).
Temperature
setting
Refrigerator section 4 to 5 °C The lower or higher the
temperature set, the higher
the energy consumption.
15
How to save energy
Normal energy consumption Increased energy
consumption
Use
Drawers, shelves and racks
arranged as they were when
the appliance was delivered.
Only open the doors when
necessary and for as short a
time as possible.
Frequent opening of the door
for long periods will cause a
loss of coldness. The
appliance works harder to
cool down and the
Store food in an organised
way.
compressor runs for longer
periods.
Take an insulated cool bag
with you when shopping and
Hot food or food at room
temperature raises the
place food in the appliance as temperature inside the
soon as possible.
appliance. The appliance
works harder to cool down
and the compressor runs for
longer periods.
Replace any food removed
rapidly, before it begins to
thaw.
Allow hot food and drinks to
cool down before placing
them in the appliance.
Store food covered or
packaged.
The evaporation or
condensation of liquids will
cause a loss of coldness in the
refrigerator.
Place frozen food in the
refrigerator to defrost.
Do not over-fill the appliance
to allow air to circulate.
16
Switching on and off
Before using for the first time
Switching off
Important:
To ensure the correct functioning of
the appliance, let it stand for 1½ to
2 hours after transporting it to its final
location before connecting it to the
mains.
^ Press the On/Off button until the
temperature display goes out.
The cooling system is switched off.
Protective foil
Switching off for longer
periods of time
The stainless steel trim to the interior
shelves and the door shelves has a
layer of protective foil to prevent
damage during transportation.
On stainless steel appliances, the
stainless steel door (and sides,
depending on model) have a layer of
protective foil to prevent damage
during transportation.
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
^ switch the appliance off,
^ disconnect it from the mains. Switch
off at the wall and withdraw the plug
from the socket, or disconnect the
mains fuse.
^ Do not remove this foil until the
appliance has been positioned in its
final location.
^ clean the appliance out and
^ leave the door ajar to air the appliance.
Cleaning
If, during a long absence, the
appliance is switched off but not
cleaned out and the door is left shut,
there is a danger of mould and
odours building up inside the
appliance.
^ Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
Switching on
^ Press the On/Off button. The
temperature display will light up.
The appliance begins to cool down, and
the temperature required shows in the
temperature display. The interior light
will come on when the door is opened.
17
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
. . . in the refrigerator
We recommend a temperature of 5 °C
in the middle of the refrigerator.
Setting the temperature
The temperature in the appliance will
rise:
^ Press the temperature selector button
repeatedly until the indicator light for
the temperature you want lights up in
the display.
– the more often the door is opened
and the longer it is kept open,
– the more food that is placed in it,
The first time you press the button the
indicator light for the last temperature
you set will flash in the display.
– the warmer the food is which is being
put into it,
The temperature value will change up
until the setting for 9 °C is reached. It
will then drop back to the 1 °C setting.
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
The newly selected temperature will be
adopted automatically after a short
while.
The indicator for the temperature which
has been set for the refrigerator will
light up constantly.
The temperature can be set slightly
colder than shown in the display if
wished.
The following example shows how this
option works:
18
The correct temperature
To set the temperature between 5 and
7 °C to be slightly colder:
Temperature display
The temperature display on the
control panel always shows the
required temperature.
^ Press the temperature selector button
repeatedly until the indicator for 5 °C
lights up.
The temperature can be adjusted from
1 °C to 9 °C.
^ Press the button for approx. another
5 seconds to set the temperature.
The colder temperature setting within
the small temperature range is now set.
However, this is not visible in the
temperature display.
19
Super cool and Dynamic cooling
Super cool
Dynamic cooling m
The Super cool function can be used to When the Dynamic cooling function is
rapidly reduce the temperature in the
refrigerator section to its lowest setting
(depending on the room temperature).
not switched on, the natural circulation
of air in the appliance will cause
different temperature zones in the
refrigerator as the cold, heavy air will
sink to the lowest section of the
Switching on Super cool
appliance. You should bear this in mind
when placing food in the appliance
(see "Using the refrigerator efficiently").
However, if you are placing a large
amount of food in the refrigerator at any
one time, it is a good idea to switch on
Dynamic cooling. This way you can
distribute the temperature inside the
appliance to all areas more evenly so
that all the food will be chilled to about
the same degree.
Super cool is particularly
recommended for faster chilling of
large amounts of fresh food or drink.
^ Press the Super cool button. The
Super cool indicator light will come
on.
The temperature is set as normal with
the temperature control.
The appliance will then work at full
power to lower the temperature.
Dynamic cooling should also be
selected when:
Switching off Super cool
– the ambient temperature in the room
is high (above approx. 30 °C), and
The Super cool function will switch itself
off automatically after approx. 6 hours.
The indicator light will go out and the
appliance will run at normal power
again.
– the room humidity level is high.
Switching on Dynamic cooling
To save energy, the Super cool function
can be switched off once food and
drinks are sufficiently chilled.
^ Press the Super cool button. The
Super cool indicator light will go out,
and the appliance will continue to
operate at normal power.
^ Press the Dynamic cooling button
m. The Dynamic cooling indicator
light will come on.
20
Super cool and Dynamic cooling
Switching off Dynamic cooling
^ Press the Dynamic cooling button
m. The Dynamic cooling indicator
light will go out.
The fan automatically switches off
when the door is open.
21
Storing food in the refrigerator
Different storage zones
Warmest area
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
The warmest area is in the top section
at the front and in the door. Use this for
storing butter and cheese.
Coldest area
The coldest area is directly above the
vegetable containers or above the fruit
and vegetable drawers (depending on
model) and on the back wall.
This appliance has dynamic cooling,
which helps to keep an even
temperature when the fan is running.
For this reason, the difference
between the various zones is less
pronounced.
Use this for all delicate and highly
perishable food, e.g.
– fish, meat, poultry,
– sausage products, ready meals,
– dishes or baked goods containing
eggs or cream,
– fresh dough, cake mixtures, pizza or
quiche dough,
– soft cheese and other dairy
products,
– pre-packed vegetables and other
fresh food with a label stating it
should be kept at a temperature of
approx. 4 °C.
22
Storing food in the refrigerator
Food which is not suitable for
storing in the refrigerator
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
Not all food is suitable for storing in a
refrigerator at temperatures below 5 °C,
as some food is sensitive to cold. The
appearance, consistency, taste and / or
the vitamin content of certain foods can
be adversely affected by being stored
in too cold a place.
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
Please be aware if storing cooking
oil in the appliance that traces of oil
can cause stress cracks to occur in
plastic components causing them to
split or break.
Food which does not tolerate cold
temperatures includes:
– Pineapples, avocados, bananas,
pomegranates, mangos, melons,
papayas, passion fruit,
citrus fruit (such as lemons, oranges,
mandarins, grapefruit),
Food must not touch the back wall of
the appliance, as it may freeze to
the back wall.
– Fruit which is not yet ripe,
– Aubergines/egg plant, cucumber,
potatoes, peppers/capiscum,
tomatoes, courgettes/zucchini,
To allow air to circulate efficiently,
do not pack food too closely
together in the refrigerator. Do not
cover the fan in the rear wall of the
refrigerator, as this is essential for
keeping the appliance cool.
– Some hard cheeses, e.g. Parmesan.
23
Storing food in the refrigerator
When shopping for food
Storing food correctly
The freshness of food when first placed Food should generally be stored
in the appliance is an important factor
in determining how long it stays fresh,
and how long it can be kept in the
covered or packaged. This will prevent
food smells from affecting other food,
food from drying out, and also any
refrigerator. Time out of the refrigerator, cross-contamination of bacteria. This is
e.g. during transportation, should be particularly important for protein-based
kept to a minimum. For example, do not foods such as meat or fish.
allow food to stay in a hot car for too
long. Note: Take a cool bag with you
when shopping and on return place
food into the appliance immediately.
The growth of bacteria, such as
salmonella, can be avoided by setting
the correct temperature and
maintaining good standards of hygiene.
Fruit and vegetables
Fruit and vegetables can be stored
loose in the vegetable containers or
drawers (depending on model).
Protein rich foods
Please note that foods rich in protein
deteriorate faster than others.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
24
Adjusting the interior fittings
Moving the shelves
The shelves can be adjusted according
to the height of the food.
^ Raise the shelf, and pull it forwards
slightly until the notch at the side is in
line with the shelf support. It can then
be raised or lowered to the required
level.
^ fit the two brackets onto the supports
The raised edge at the back must face
upwards to prevent food from touching
the back of the appliance and freezing
to it.
on either side at the required height,
^ and push the glass shelves in one
after the other.
The shelf with the raised edge must
be at the back.
Stoppers prevent the shelves from
being dislodged by mistake.
Adjusting the door shelf/bottle
shelf
Split shelf
In order to accommodate tall items in
the appliance, one of the shelves is
divided. The front section can be
pushed under the rear section.
^ Push the door/bottle shelf upwards,
then remove it by pulling it forwards.
^ Replace the door/bottle shelf at the
required position. Ensure that it is
securely pushed back into position.
^ Push the rear half of the glass shelf
up slightly from below.
^ At the same time, pull the front half of
the glass shelf forwards slightly and
then push it carefully under the rear
half.
To move the split shelf:
^ Take both halves of the split glass
shelf out,
25
Adjusting the interior fittings
Fruit and vegetable containers
The fruit and vegetable containers are
pushed in and out on telescopic
runners, and can be completely
removed if necessary.
^ Pull the container right out and then
lift it up and off.
Push the runners back in again to
avoid injury or damage.
To replace a container,
^ place it back on the fully extended
runners a. The front of the runners
must be right up against the front of
the container b.
^ Then push the container back in c.
26
Automatic defrost
The refrigerator defrosts automatically.
Condensate and frost can build up on
the back wall of the refrigerator whilst it
is in use. You do not need to remove
this, as it will defrost and evaporate
automatically with the warmth
generated by the appliance.
The condensate is drained away via a
channel and drain hole into an
evaporation system at the back of the
appliance.
Ensure that the condensate channel
and drain hole are kept clean and
are never blocked so that
condensate can flow away without
hindrance.
27
Cleaning and care
To avoid damaging the surface of
your appliance, do not use:
A range of Miele branded cleaning
and conditioning products is
available to order from Miele (see
back cover for contact details).
Make sure that no water can
penetrate into the electronic unit or
into the light.
– cleaning agents containing soda,
ammonia, acids or chlorides,
– cleaning agents containing
descaling agents,
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
Do not let water get into the
condensate channel and drain hole
when cleaning.
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
Do not use steam cleaning
apparatus to clean the appliance.
Steam could reach electrical
components and cause a short
circuit.
– oven sprays,
– glass cleaning agents,
– hard, abrasive sponges and
brushes, e.g. pot scourers,
The data plate located inside the
appliance must not be removed. It
contains information which is required
in the event of a service call.
– melamine eraser blocks,
– sharp metal scrapers.
Before cleaning
The stainless steel door has a
special finish which is resistant to
soiling.
^ Switch off the appliance.
^ Disconnect it from the mains.
Do not treat the door with stainless
steel conditioning agent as this will
cause noticeable smearing.
^ Take any food out of the appliance
and store it in a cool place.
^ Take out any removable parts for
However, do use Miele stainless
steel conditioning agent to treat the
other stainless steel surfaces of the
appliance (available from Miele).
Unlike stainless steel cleaning
cleaning.
agents, the conditioning agent does
not contain any abrasive substances
and will gently remove soiling. Each
time it is used, it forms a water and
dirt repellent protective coating.
28
Cleaning and care
Cleaning the interior and
accessories
^ After cleaning, wipe the interior and
accessories with a damp cloth and
dry with a soft cloth.
^ Clean the appliance at least once a
Leave the door open to air the
appliance for a short while.
month.
Remove soiling immediately to
prevent it from drying on.
Appliance door, side panels
Remove any soiling from the
appliance door and side panels
immediately.
Use lukewarm water with a little
washing-up liquid.
The following are dishwasher safe:
If this is not done, it might become
impossible to remove and could
cause the surface to alter or
discolour.
– the butter dish, egg trays
(supplied as standard, depending on
model)
– the shelves and bottle shelf in the
door
All surfaces are susceptible to
scratching.
– the butter and cheese compartment
Contact with unsuitable cleaning
agents can alter or discolour the
surfaces.
The temperature of the dishwasher
programme must not exceed 55 °C.
Contact with some foodstuffs, such
as carrots, tomatoes or ketchup can
cause plastic items to discolour.
However, this discolouration will not
affect the stability of plastic items.
^ The surfaces should be cleaned
using a solution of hot water and a
little washing-up liquid applied with a
soft sponge. They can also be
cleaned with a damp microfibre cloth
(without using any cleaning agent).
^ Clean the interior shelves and
drawers by hand. These are not
suitable for cleaning in a dishwasher.
^ After cleaning, wipe with clean water
and dry with a soft cloth.
^ Clean the condensate channel and
drain hole frequently, so that
condensate can drain away
unhindered. Use a straw or similar to
clear the drain if necessary.
29
Cleaning and care
Stainless steel appliance door:
Back of appliance -
compressor and metal grille
The appliance door has a high quality,
special finish which is resistant to
soiling and is very easy to clean.
The compressor and the metal grille at
the back of the appliance (heat
exchanger) must be dusted at least
once a year. A build-up of dust will
increase the energy consumption of the
appliance.
Do not use the following to
clean/condition the door
– stainless steel cleaning agent:
this will damage the surface.
– Miele stainless steel conditioning
agent:
When cleaning make sure that the
cable and other components do not
get broken, kinked or damaged in
any way.
this will cause noticeable smearing.
Ventilation gaps
After cleaning
^ The ventilation gaps should be
cleaned on a regular basis with a
brush or vacuum cleaner. A build-up
of dust will increase the energy
consumption of the appliance.
^ Replace all shelves and accessories
in the appliance.
^ Reconnect to the mains and switch
the appliance back on.
^ Switch on the Super cool function for
a while so that the appliance can
cool down quickly.
Door seal
Do not use any oils or grease on the
door seal as these will cause the
seal to deteriorate and become
porous over time.
^ Place food back in the appliance and
close the door.
^ The door seal should be cleaned
regularly with clean water and then
wiped dry with a soft cloth.
30
Problem solving guide
^ Check whether the metal grille (heat
exchanger) at the back of the
Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous.
appliance has become dusty.
^ The appliance door is being opened
frequently.
^ Check that the door has been closed
properly.
. . . the interior lighting in the
refrigerator is not working.
What to do if . . .
^ Was the refrigerator door left open for
too long? The lighting switches itself
off automatically after approx. 15
minutes if the door is left open.
. . . the appliance does not get cold.
^ Check whether the appliance has
been switched on. The temperature
display must be lit up.
If this is not the case, then the interior
lighting is defective.
^ Check that the plug is correctly
inserted into the socket and switched
on.
^ Call Miele Service.
The LED lighting may only be repaired
or replaced by a service technician.
There are live electrical components
under the cover. Danger of injury and
damage to the appliance.
^ Check that the mains fuse has not
tripped. If it has, there could be a
fault with the refrigerator, the
household electricity supply or
another appliance.
Contact a qualified electrician or the
Miele Service department.
Do not remove the cover. If the
cover is damaged or needs to be
removed due to damage, exercise
caution. There are lasers in the
lighting (laser beam class 1M) which
you should avoid looking at directly.
Do not use optical instruments
(magnifying glass or similar) to look
at the lighting either.
. . . the temperature in the refrigerator
section is too low.
^ Set the required temperature.
^ The Super cool function is still
switched on. Super cool will switch
itself off after 6 – 12 hours.
. . . the compressor is switching in
too frequently and for too long.
^ Check whether the ventilation gaps
have been covered over or become
dusty.
31
Problem solving guide
. . . the floor of the refrigerator is wet.
The condensate drain hole is blocked.
^ Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact Miele Service.
To prevent unnecessary loss of
temperature it is advisable not to
open the door while waiting for the
appliance to be serviced.
32
Noises
Normal noises
What causes them
Brrrrr...
Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....
Click....
A gurgling noise can be heard when coolant is circulating
through the pipes.
Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....
Creak ...
On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectify
What causes them, and what can you do about
them
Rattling, vibrating
The appliance is uneven: Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets or shelves are unstable or sticking: Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other? Separate them.
The transport cable clips are hanging loose at the back of
the appliance: Remove the clips.
33
After Sales / Guarantee
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Dealer
or
– Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However, you must activate
your cover by calling 0845 365 6640 or
34
Electrical connection
Electrical connection U.K.
If the connection cable has to be
replaced, this must be done by a
suitably qualified and competent
person.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
Do not plug other appliances in behind
this appliance
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. It must not be located
behind the appliance. For extra safety it
is advisable to protect the appliance
with a suitable residual current device
(RCD).
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
WARNING
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
THIS APPLIANCE MUST BE
EARTHED
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.
35
Installation
– The plug and cable must not touch
the rear of the appliance as they
could be damaged by vibrations
from the appliance.
Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance. There is the danger of
these catching fire.
– Do not plug in other appliances
behind this appliance.
Side-by-side installation
Important. In environments with
high humidity condensation can
build up on the exterior of the
appliance. This can cause corrosion
of the appliance walls. For
To avoid a build-up of condensation
and resultant damage, refrigerators and
freezers should not generally be
installed side-by-side next to each
other.
prevention, it is advisable to install
the appliance with sufficient
ventilation in a dry and /or
However, some appliances have
side-wall heating, making them suitable
for side-by-side installation with this
refrigerator.
air-conditioned room.
Make sure that appliance door is
closing and sealing properly, the
ventilation gaps are not covered and
the appliance is installed in
accordance with these istallation
instructions.
Your dealer will be able to advise you
on which models are suitable.
^ Follow the instructions for the other
appliance on how to install the two
appliances side by side.
Location
This appliance should not be installed
where it is exposed to direct sunlight or
directly adjacent to a heat-producing
appliance such as an oven or a
radiator. The higher the ambient
temperature of the room the more
energy the appliance requires to
operate. The appliance should be
installed in a dry well ventilated room.
When installing the appliance please
be aware:
– The socket must be easily accessible
in an emergency, not concealed
behind the appliance.
36
Installation
Climate range
Aligning the appliance
The appliance is designed for use within
certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate.
Climate range
Ambient room
temperature
SN
N
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
^ To align the appliance, adjust the
front feet using the spanner supplied.
ST
T
Levelling the appliance door
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise with
the risk of food deteriorating and going
off.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be covered
or blocked in any way. They should be
dusted on a regular basis.
^ Ensure that you unscrew adjusting
foot a until it sits on the floor. Then
unscrew the foot by a further 90°.
Installation
^ Remove the cable clip from the back
of the appliance.
^ Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^ Carefully push the appliance into
position with its back against the wall.
37
Installation
Appliance dimensions
A
B
C
K 11820 SD, K 12820 SD,
K 12820 SD edt/cs
1 850 mm
600 mm
630 mm
38
Changing the door hinging
The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
Removing the door handle
To change the door hinging you will
need the following tools:
Two people are needed for
changing the door hinging.
^ Pull door handle a towards you. Side
section b slides back.
^ Pull side section b firmly back out of
the guides on the mounting plate.
^ Undo the 4 screws (TX 15) in the
mounting plate, and remove the
handle.
^ Remove the cover caps from the
opposite side, and fit them into the
empty holes.
39
Changing the door hinging
Changing over the door
^ Then separate retaining plate f from
cover e, by pushing it slightly to the
left and then pulling the cover
forwards and off.
Make sure the door shelves are
empty!
^ Rotate retaining plate f by 180°.
^ Close the appliance door.
^ Then fit cover e from the front over
retaining plate f, and slide it over to
the right. The writing must be visible.
^ Remove cover g, then rotate it by
180° and fit it on the opposite side.
^ Then fit cover e together with
retaining plate f on the opposite
side.
^ Remove cover a by sliding it
forwards from the back and then
lifting it off.
^ Remove cover b by pulling it
upwards.
Caution. The door is not secure as
soon as the hinge plate is removed.
^ Loosen screws d in upper hinge
plate c and pull it upwards and off.
^ Carefully lift the door off and place it
to one side.
^ Carefully ease off cover e from
above using a screwdriver and then
take it off together with retaining plate
f.
40
Changing the door hinging
^ Pull hinge pin a together with disc b
and adjustable foot c upwards and
off.
^ Remove cover cap d.
^ Undo screws e and take hinge plate
f off.
^ Remove cap h from the bearing
bush in the door and refit on the
opposite side.
^ Undo the screw of hinge part h on
hinge plate f slightly. Fit it into the
hole opposite in hinge plate f and
tighten up the screw.
^ Refit cover cap d in the other hole.
^ Remove cover g and fit it into the
holes on the opposite side.
^ Using a screwdriver, remove spring
clamp i from underneath the door
and fit it on the opposite side.
41
Changing the door hinging
^ Screw hinge plate f into position on
the opposite side using the two outer
long slots only. To make it possible to
align the door later, do not replace
the centre screw at this stage.
^ Fit hinge plate c onto the opposite
side and secure it with screws d.
^ Fit covers a and b to their opposite
sides.
^ Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
^ Important. Screw the adjustable foot
c into hinge pin a as far as it will go.
^ Refit hinge pin a together with disc
b and adjustable foot c. Important.
The notch at the bottom of the hinge
pin should face towards the back.
^ Place the door onto hinge pin a.
^ Close the appliance door.
42
Changing the door hinging
Refitting the handle
It is important to check that the side
section of the handle d does not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^ Realign mounting plate c with grub
screws a until the mounting plate
and the side section of the handle d
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
^ Loosely attach the handle to the
opposite side of the door with the two
front screws b.
Mounting plate c must be positioned
on the side of the door so that when the
door is closed it is flush with the side of
the appliance.
If this is not the case,
^ tighten both grub screws a with a
suitable allen key until mounting plate
c lines up correctly.
^ Then tighten all 4 screws b.
^ Slide the side section of the handle
d into the guides on the mounting
plate until it clicks into place.
43
Aligning the appliance door
The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be used again.
44
Building in the appliance
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installed next to a wall d a
distance of approx. 55 mm must be
maintained on the hinge side between
the wall d and the appliance b, so
that the doors and the handles have
sufficient space for opening.
aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box a.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm2 to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
45
46
47
Alteration rights reserved / 4912
M.-Nr. 09 434 270 / 00
K 11820 SD, K 12820 SD, K 12820 SD edt/cs
|