INSTALLATION/OPERATION MANUAL
MIRATRON WIRELESS
REMOTE CONTROL RADIO
MAYCO MODEL C30HDG
Revision #0 (08/19/09)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALL TIMES.
WARRANTY
LIMITED ONEYEAR WARRANTY
Miratron Incorporated, hearafter referred to as Miratron, is providing this
warranty in lieu of all other express or implied warranties, including any
warranty of merchantability or fitness for a particular purpose.This warranty
is buyer’s exclusive remedy for all claims against Miratron. Miratron shall
not be liable for any consequential or incidental damages. Miratron’s total
liability for all contracts, negligence, or other claims shall be limited to the
price paid for its product.
Miratron promises buyer that any Miratron product purchased by buyer shall
be free from all material defects in desgin, material, or manufacturing for a
period of one year from the manufacture date; provided, however, that the
warranty shall not extend to ordinary wear and tear or to normally replaceable
components (e.g., batteries).
During the warranty period, Miratron may repair or replace (in its sole
discretion) any product suffering from a warranty defect and returned
freight prepaid by buyer, with no charge to buyer for any warranty repair or
replacement.
The warranty shall remain in full force and effect for such 1 year period,
provided that the product: (1) was installed, operated, and maintained
properly;(2) has not been abused or misused;and (3) has not been repaired,
altered, or modified outside of Miratron’s authorized facilities. This warranty
provides specific legal rights that may be varied by state law.
Miratron products are not designed for life or safety applications.
Product specification subject to change without notice.
NOTICE
System must be physically disconnected from the
machine prior to welding on the machine. Welding
may cause permanent damage to sensitive electronic
components, and will void this warranty.
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 3
OVERVIEW
ALWAYS read manual before attempting to operate the
equipment. Failure not to read manual could cause severe
equipment damage and or damage to the receiver and
transmitter.
Make sure work area is safe to operate radio control receiver and
transmitter.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
If any problems or malfunctions occur using this product, discontinue use
immediately, and refer to the Troubleshooting Guide in this manual. If the
problem persists, call your equipment dealer immediately for parts and or
service.
NOTICE
Disconnect and lock-out all power sources before
making any wiring connections to the receiver.
NOTICE
Improper operation of the transmitter receiver could
cause damage to the equipment. DO NOT allow
unauthorized personnel to operate this equipment
before reading manual.
NOTICE
MIRATRON, Inc. transmitters and receivers are not
intended for life or safety applications, MIRATRON,
Inc. shall not accept resposibility for installation,
application, or safety of machine or systems which
utilize MIRATRON, Inc. transmitters and receivers.
PAGE 4 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
SPECIFICATIONS
Table 1. Specifications
Miratron Model Number:
RX4 Radio Control Receiver
CMD16-0135 ~ (MQ P/N EM98215)
12-24VDC, 500mA max
General:
Power Requirements
Radio:
Frequency Standard
Frequecy Control
FCC ID
902-928 MHz, FHSS, ISM Band
Direct FM
OUR9XCITE (Standard)
-106 dBM
Receiver Sensitivity
CMD16-0135 ~ (MQ P/N EM98215)
300 ft. (91.44 meters) Line of Sight (Standard)
Transmitter:
Range
1.5 Volt “AA” Alkaline (4)
Battery Type
Standby, 80 hrs. — Transmitt, 12-16 hrs.
Standby, 40 hrs. — Transmitt, 6-8 hrs.
Battery Life (Standard)
Battery Life (Extended Range)
Flashing = Battery Good
Double Blink = Battery Low
LED Indicator
Enclosure:
Transmitter
Environmental:
Operating
High Impact Polystyrene
-14° F ~ 158° F (-10°C ~ 70° C)
-40° F ~ 185° F (-40°C ~ 85° C)
Storage
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 5
CARE AND HANDLING
Transmitter:
Clean transmitter gently with a damp cloth. DO NOT immerse transmitter
in water, or spray with hose. DO NOT store outside.
DO NOT drop transmitter or otherwise subject transmitter to physical
shock.
DO NOT expose transmitter to extreme temperatures.
DO NOT open transmitter enclosure.Transmitter contains no serviceable
parts.
Receiver:
Remove receiver from machine prior to welding on machine
DO NOT paint electrical connector.
Use only factory provided antenna and cabling.
DO NOT open receiver enclosure except to change radio channel or make
adjustments to factory settings.
Use transmitter to test functions. DO NOT apply voltage to circuit board
directly.
PAGE 6 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
RECEIVER INSTALLATION
Parts:
Make sure all parts are accounted for before performing the installation.
The following parts are included with the kit:
Radio Transmitter
Radio Receiver
Spiral Antenna with associated mounting hardware
Coaxial Antenna Cable
Data /Power Cable (7-wire)
Remote Control Cable
Battery Disconnection
1. Disconnect the negative terminal of the battery cable from the battery.
Antenna Mounting
1. Drill a 3/4” hole into the hood on the C30HDG as shown in Figure 1.
2. After hole has been drilled, deburr hole opening.
3. Tilt the engine hood slightly forward to gain access to the antenna hole
opening. Support the hood with a block of wood to maintain the desired
access position.
4. Insert antenna cable thru 3/4” hole opening in hood. Insert BNC end of
cable first.
5. With one hand holding the antenna end of the cable through the antenna
hole opening, connect the locking flange, antenna and rubber gasket.
Tighten locking flange securely.
6. Secure coaxial antenna with pressed on tie-wrap pads (interior). Also
apply pressed on tie-wrap pads (exterior) to the control box support
panel (bottom).
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 7
RECEIVER INSTALLATION
Radio Control Receiver Mounting
1. Drill two 1/4” holes into the control box support panel on the C30HDG
as shown in Figure 1.
2. After both holes have been drilled, deburr each hole opening.
3. Using a 1/4-20 x 1-1/4 bolt (2), 1/4 lock washer (2), 1/4 flat washer (2)
and 1/4 nut (2), mount the radio control receiver onto the control box
support panel as shown in Figure 1.
4. Connect BNC end of coaxial antenna cable to BNC connector on radio
control receiver.
STEP 5
LOCKING
FLANGE
ANTENNA
RUBBER
GASKET
ANTENNA
END
COAXIAL
CABLE
RX4
4
RA
AD
IO
CEIVENT
R
RE
CONTR
IVE ROL
L
MIRA
RA
TRON
ON
BNC CONNECTOR
RECEIVER
END
STEP 6
LOCKING
FLANGE
TIGHTEN
COAXIAL
CABLE
RX4
4
AD
RADIO
RECEICVER
IO
CE
O
O
R
L
MIRA
RA
TRON
ON
DATA
CABLE
TIE-WRAP
PADS
(INSIDE)
TIE-WRAP
PADS
(OUTSIDE)
CABLE
SERVICE
LOOP
Figure 1. Antenna/Receiver Installation
PAGE 8 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
CABLE INSTALLATION
Control Box Removal
1. Using a 7/16 socket remove the mounting bolts (3) that secure the control box
to the support bracket.
2. Once the bolts have been removed, flip the panel downward to gain access to
the connection points.
Data Cable Connections
1. Wire data cable into control box as shown in Figure 2.
2. Crimp a 16-14 (3/16”) terminal ring onto the RED wire labeled BATT+.Connect
this end of the wire to the +12VDC terminal strip, pin 2.
3. Crimp a #16-14 (3/16”) terminal ring onto theWHITE wire labeled DECREASE.
Connect this end of the wire onto pin 3 on the throttle high low switch.
4. Crimp a 16-14 (3/16”) terminal ring onto the WHITE wire labeled INCREASE.
Connect this end of the wire to pin 1 of the throttle high low switch.
5. Crimp a #16-14 (3/16”) terminal ring onto the WHITE wire labeled PIN 9.
Connect this end of the wire to pin 2 on the pumping control switch.
6. Crimp a #16-14 (5/16”) terminal ring onto the BLACK wire labeled FRAME
GROUND. Connect this end of the wire to engine chassis ground.
7. Splice the WHITE wire labeled EMERGENCY STOP with the RED or PINK
wire from the engine oil sensor.
8. Insert connector end of data cable into Miratron receiver.
Remote Control Cable Connections
1. Connect the remote control cable to the control box as shown in Figure 2 .
2. Splice the WHITE wire labeled REMOTE (data cable) with the BLACK wire
from the yellow remote cable
3. Crimp a #16-14 (3/16”) terminal ring onto theWHITE wire from the yellow remote
cable. Connect this end of the wire to pin 1 on the pumping control switch.
4. Re-install control box using the existing mounting hardware.
5. Insert the yellow remote control cable into the 2-pin receptacle labled REMOTE
OUTLET on the control box.
6. Reconnect negative battery cable to battery.
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 9
WIRING DIAGRAM
RED OR PINK
12-PIN
DATA CABLE
CONTROL
RADIO
RECEIVER
RX4
SPLICE
TRON
IRA
M
ENGINE OIL
SENSOR
3
EMERGENCY
STOP
PIN 4 (WHITE)
HOUR
METER
7-WIRES
FRAME GROUND
BLACK
R
E
M
O
T
BATT + (RED)
ADD
TERMINAL
RING
DECREASE (WHITE)
INCREASE (WHITE)
E
CHECK
ENGINE
HOOD
OPEN
REMOTE (WHITE)
C
A
B
L
PIN 9 (WHITE)
WHITE
E
Y
E
L
L
BLACK
O
W
1
2
3
TERMINAL
STRIP
(+12VDC)
SPLICE
PUMPING
CONTROL
SWITCH
2
1
WHITE (ADD)
BLACK (ADD)
BATT +
2
1
DECREASE
INCREASE
ADD
IGNITION
SWITCH
ADD
TERMINAL
RING
TERMINAL
RING
EMERGENCY
STOP
SWITCH
2
1
3
T
H
R
O
T
T
L
E
H
IG
H
L
O
W
THROTTLE
HIGH/LOW
SWITCH
EME
RGENC
C
E
H
N
E
G
Y
C
K
ST
OP
1
IN
H
O
E
O
D
N
O
P
E
IG
NITIO
N
S
W
O
FF
ITCH
O
N
E
N
G
IN
E
H
S
TA
RT
O
U
R
S
P
U
M
P
IN
G
C
O
N
R
T
R
E
M
O
O
O
N
T
L
E
NOTE:
O
FF
P
U
M
R
E
P
M
O
O
T
E
T
N
O
U
T
L
E
WIRING DIAGRAM SHOWS REAR VIEW OF COMPONENTS.
1
CONNECT YELLOW
REMOTE CABLE TO
RECEPTACLE LABELED
“REMOTE OUTPUT”
TERMINAL STRIP IS NOT MARKED. WIRE CAN BE CONNECTED
TO ANY PIN (+12VDC BUS). PIN 2 RECOMMENDED.
2
3
ENGINE OIL SENSOR IS LOCATED BEHIND LEFT REAR OF CLUTCH.
Figure 2. Wiring Diagram
PAGE 10 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
TRANSMITTER/RECEIVER
The definitions below describe the controls and functions of the Miratron
Transmitter and Radio Control Receiver.
Transmitter
1. Power On Switch — Place this switch in the ON position to turn on the
transmitter.Be sure to place this switch in the OFF position when the system
is not in use.
2. Status LED Indicator — Status LED blinks to indicate transmitter is ON
and active. LED will double-blink when battery strength is low.
3. E-STOP Switch — When activated will cause the engine stop and all
pumping will cease.
4. Belt Clip — If desired the transmitter can be placed on a belt.
5. Pump ON/OFF Switch — Place this switch in the pump ON position to
begin pumping. Place the switch in the OFF position to stop pumping.
6. Engine Speed Switch — Place this switch upward to increase engine
speed. Place downward to decrease engine speed.
7. Batteries — Transmitter requires four AA 1.5V alkaline batteries. If
rechargable batteries are to be used, nickel-metal hydride (NiMH) are
recommended.
Receiver (Learn Button)
Transmitter and receiver must be matched as a pair. Perform the procedure
listed below to pair the transmitter and receiver.
1. Place the ignition switch in the ON position.
2. Verify that the status LED on transmitter blinks (active).
3. Place the pumping control switch on the control box in the REMOTE ON
position.
4. Press and hold the learn button on the RX4 radio control receiver. While
keeping the learn button depressed, toggle the pump ON/OFF switch for
10 seconds.
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 11
TRANSMITTER/RECEIVER
Functional Test
Perform the functional test procedure below to test the remote control radio
system..
1. Start the engine as outlined on the operator’s manual.
2. Place the transmitter power ON/OFF switch in the ON position.
3. Place the pumping control switch on the control box in the REMOTE ON
position.
4. Toggle the engine speed switch back and forth. Verify that engine speed
increases and decreases.
5. Toggle pump ON/OFF switch. Verify that pumping starts and stops.
POWER
ON
STATUS E-STOP
BELT CLIP
TRANSMITTER
MODEL CDM16
PUMP
ON
PUMP ON/OFF
SWITCH
ENGINE
INCREASE
BATTERY
COMPARTMENT
OFF
+
+
DECREASE
1.5V 1.5V 1.5V 1.5V
4 AA 1.5V
ALKALINE
BATTERIES
REQUIRED
A
L
K
A
L
I
A
L
K
A
L
I
A
L
K
A
L
I
A
L
K
A
L
I
ENGINE SPEED
SWITCH
N
E
N
E
N
E
N
E
R
X
4
RX4 RADIO
CONTROL RECEIVER
MODEL CDM16
R
A
D
IO
R
E
C
C
O
EIV
N
ER
TR
O
L
MIRA
TRON
LEARN
BUTTON
Figure 3. Transmitter/Receiver
PAGE 12 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
TROUBLESHOOTING
Table 2. Troubleshooting
Symptom
Possible Problem
Solution
Transmitter does not
function at all
LED status indicator not
flashing.
Turn transmitter power
switch ON.
Weak dead battery, replace
batteries.
Check orientation of
batteries.
Make sure transmitter has
be matched (paired) to
receiver.
LED indicator not lit when
power ON/OFF switch is
pressed.
Receiver is not powered
up.
Transmitter range is poor
LED indicator not lit when Weak dead battery, replace
power ON/OFF switch is
pressed
batteries.
LED indicator lit when
switch is pressed
Check receiver antenna
Maintain line-of-sight
Avoid obstructions
Check for interference
Heavy rain reduces range
Transmitter works (RX LED Check wiring.
in receiver comes on) but
Make sure output wires are
not shorted to Ground
outputs do not operate
Verify load is wired
correctly.
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 13
SYSTEM WIRING DIAGRAM
Figure 4. System Wiring Diagram
PAGE 14 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09)
NOTE PAGE
INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 15
INSTALLATION/OPERATION MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Mayco Parts
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Fax: 310-631-5032
Service Department
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Tel: 0161 339 2223
Fax: 0161 339 3226
Contact: [email protected]
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2009, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mayco logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
|