24-01-2006
Nilfisk-ALTO E 130.1, E 140.1
EN
User Manual
EN
Index
1
2
3
4
5
Safety precautions and warnings .............................................3
Description ...............................................................................4
Before you start using your pressure washer...........................5
Operating your pressure washe ...............................................6
Fields of Application
and Working Methods...............................................................9
After using your pressure washe............................................11
Maintenance...........................................................................12
Trouble Shooting ....................................................................13
Further information.................................................................14
6
7
8
9
10 EC Declaration of Conformity.................................................17
1 Safety Precautions and Warnings
Symbols used to mark in-
structions
Before starting up
your high pres-
sure washer for
This symbol is
used to mark safety
instructions that
must be ob-
the first time, this
instruction manual
served to prevent
damage to the ma-
chine and its performance.
ꢀ
must be read through carefully.
Save the instructions for later
use.
This symbol
indicates tips
and instructions
Safety instructions
marked with this
symbol must be
to simplify work and to ensure a
observed to pre-
safe operation.
vent danger to persons.
WARNING!
ꢁNever use the machine in
an environment where there
could be a danger of explo-
sion. If any doubt arises,
please contact the local
authorities.
ꢁHigh pressure jets can be
dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.
Do not let children or people
who have not read the instruc-
tion manual operate the ma-
chine.
ꢁNever try to clean clothes or ꢁIt is not allowed to clean as-
footwear on yourself or other
persons.
ꢁHold the spray lance firmly
with both hands. The spray
lance is affected by a thrust
bestos-containing surfaces
with high pressure.
ꢁThis high pressure washer
must not be used at tempera-
tures below 0°C.
Before starting up your machine
please check it carefully for
any defects. If you find any, do
not start up your machine and
contact your Nilfisk-ALTO dis-
tributor.
of up to 26.5 Nm during ope- ꢁNever let any persons stay
ration.
under the product when
stored on the wall.
ꢁThe operator and anyone in
the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles during opera-
tion.
Especially check:
ꢁThe insulation of the electric
cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Nilfisk-ALTO dis-
tributor should replace it.
WARNING!
Inadequate extension cables
can be dangerous. Cables on
drums should always be com-
pletely unwinded to prevent the
cable from overheating.
3
Extension cables should be of ꢁOnly connect the machine to
Repair and maintenance
WARNING! Always remove the
electric plug from the socket be-
fore carrying out maintenance
work on the machine.
EN
a watertight construction and
comply with the below-men-
an installation with earth con-
nection.
tioned requirements for length ꢁThe electric installation shall
and cable dimensions.
be made by a certified elec-
trician.
ꢁIt is strongly recommended
that the electric supply to this
machine should include a re-
sidual current device (GFCI).
1.0 mm² max.
1.5 mm² max.
2.5 mm² max.
12.5 m
20 m
30 m
Safety devices
Locking device on spray gun
(7a) (see foldout at the end of
this manual):
ꢁCable connections should be
kept dry and off the ground.
The spray gun features a lock-
ing device. When the pawl is
activated, the spray gun cannot
be operated.
Water connection
Connection to the public mains
according to regulations.
Mains power connection
IMPORTANT! Only use wa-
ter without any impurities. If
there is a risk of running sands
in the inlet water (i.e. from your
own well), an additional filter
should be mounted.
Thermal sensor:
A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen-
sor has cooled.
The following should be ob-
served when connecting the
high pressure washer to the
electric installation:
2 Description
2.1 Application
This high-pressure washer has
been developed for domestic
use within:
Only use the high-pressure
washer for purposes described
in this manual.
-
Car, Motorbike, boat, cara-
van, trailer, patio/drive/flags-
tones, woodwork, brickwork,
barbecue, garden furniture,
lawn mower
The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.
Section 5 describes the use of
the high-pressure washer for
vaious cleaning jobs.
2.2 Operation elements
and model survey
See foldout at the end of this
manual.
13 Hose reel (not standard)
14 Hose hook
15 Model tag
1 Start/stop switch
16 Quick coupling
2 Water inlet (with filter)
3 High pressure connection
4 High pressure hose
5 Electric cable
Specifications: See model tag
(15) of machine.
6 Click & Clean spray lance
7 Spray gun with lock
8 Click & Clean Tornado PR
Sound pressure level measures
in accordance with ISO 3744
EEC directive 2000/14/EEC:
LpA = 69,9 dB(A), LWA = 84
dB(A).
®
nozzle
®
9 Click & Clean Powerspeed
nozzle
10 Click & Clean foam sprayer
11 Nozzle cleaning tool
12 Trolley handle
We reserve the right to alter the
specifications.
4
EN
3 Before you start using your
pressure washer
3.1 Mounting of trolley
handle (models with
trolley handle)
1. Remove the label on top of
machine.
2. Push down the trolley handle
(12) into the machine. Secure
the handle by tightening the
2 screws.
ꢀꢁ
ꢀꢂ
3. Mount the hose hook (14)
on the handle (3 screws).
Note: the hose hook can be
mounted on the front as well
as on the back. Front position
is to be used if the product is
used together with a special
wall hook for wall storage.
3.2 Mounting of hose reel
handle (models with
hose reel)
1. Click the hose reel handle
on to the trolley handle (no
screws).
3.3 Mounting of quick
coupling
1. Screw the quick coupling (16)
tight on to the water inlet (2).
Note: The inlet filter must al-
ways be fitted in the water inlet
pipe to filter out sand, limestone
and other impurities as these
will damage the pump valves.
Caution: Failure
to fit the filter will
invalidate the
guarantee.
ꢀ
5
EN
4 Operating your pressure washer
4.1 Connection of high
pressure hose (models
without hose reel)
1. Mount the high pressure
hose on the outlet (3).
4.2 Mounting of spray
lance and Click & Clean
nozzles
1. Push the spray lance (6) into
the spray gun (7) and screw
it on.
Note: The
spray lance (6)
has a built-in
ꢀ
low pressure nozzle that can
be used for flushing away
dirt.
2. Attach the nozzle.
Warning: When
attaching the Click
& Clean noz-
zles, the pawl on
ꢀ
the side of the spray
lance should come out again.
®
Note: The Tornado PR nozzle
and the foam sprayer feature a
swivel lock, which must be posi-
tioned in the hole in the Click &
Clean spray lance.
Press the pawl to detach the
Click & Clean nozzle.
6
4.3 Water connection
An ordinary 1/2" garden hose
of min. 5 m and max. 25 m will ter without any impurities. If
IMPORTANT! Only use wa-
EN
be suitable.
there is a risk of running sands
in the inlet water (i.e. from your
own well), an additional filter
should be mounted.
1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrat-
ing the machine.
Note: Check that the filter is
fitted in the water inlet pipe
and that it is not clogged up.
2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 50°C).
3. Turn on the water.
NOTE: Connection to the public
mains according to regulations.
4.4 Start and stop of the ma-
chine (when connected to
a water supply)
The spray lance is affected
by a thrust during operation
- therefore always hold it firmly
with both hands. IMPORTANT:
Point the nozzle at the
ground.
Do not cover the machine
during operation or use it in a
room without adequate ventila-
tion !
Note: If the ma-
chine is left or not
1. Check that the machine is in
upright position.
used for 5 min-
utes, it must be switched off on
the start/stop switch "O" (1):
NOTE: Do not place the
machine in high grass!
2. Release the trigger lock.
3. Activate the trigger of the
spray gun and let the water
run until all air has escaped
from the water hose.
4. Press the Start/stop switch
"I" (1).
5. Activate the trigger of the
1. Press the start/stop switch
"O".
2. Disconnect the electrical plug
from the socket.
3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.
4. Lock the spray gun.
spray gun.
When releasing the trigger of
the spray gun, the machine au-
tomatically stops. The machine
will start again when you re-ac-
tivate the spray gun.
Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.
7
4.5 Start the machine (when
connected to open con-
tainers (suction mode))
The washer can take in water
from a rain water tank as an
example. The hose for the wa-
ter supply must not be too long,
approx. 5 m.
1. Place the other end of the
water hose in the water tank.
Use an external filter if the
water contains impurities.
2. Press the start/stop switch
"I".
EN
Make sure that the water tank
is not placed on a lower level
than the machine.
3. Activate the trigger of the
spray gun and let the water
run, until the air has escaped
from the water hose and the
pump.
4. Mount spray lance and
nozzle.
4.6 Pressure regulation on
The pressure can be regulated
on the TORNADO PR nozzle.
®
®
the TORNADO PR-
nozzle
High pressure
Low pressure
4.7 Stationary use
If mounting a special wall hook
(not standard), the pressure
washer can be used as a sta-
tionary solution meaning that it
can be operated while hanging
on the wall.
B
C
Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawl-
plugs to the type of wall.
On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.
D
Important: The
bearing capacity
of the wall hook
is max. 30 kg.
ꢀ
8
EN
5 Fields of application and working
methods
5.1 General
Efficient high presure cleaning is achieved by following a few guide-
lines, combined with your own personal experience of specific
cleaning tasks. Accessories and detergents, when correctly cho-
sen, can increase the efficiency of your pressure washer. Here is
some basic information about cleaning.
5.1.1 Detergent and foam
Foam or detergent should be applied onto dry surfaces so that the
chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface be-
ing cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be damaged.
5.1.2 Mechanical effect
In order to break down tough layers of dirt, additional mechanical
effect may be required. Special wash brushes offer this supplemen-
tary effect that cuts through dirt (especially by car washing).
9
5.2 Typical fields of application
EN
Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer
from Nilfisk-ALTO in association with accessories and detergents.
Task
Accessories ‘Click Cleaning method
& Clean’
Car nozzle,
auto brush,
underchassis
nozzle,
Foam sprayer,
Car Combi Cleaner
1. Apply Car Combi Cleaner with the foam sprayer. Always
start from the bottom and work upwards. Let Car Combi
Cleaner act for at least 5 min.
Car
2. Wash the car with the car nozzle, which has been optimized for
quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work back-
wards to avoid water from penetrating by the door mouldings.
3. Use the brush for removal of traffic film which is not removed by the
nozzle. If the car is very dirty, apply Car Combi Cleaner again.
4. Attach the undercarriage nozzle and clean undercarriage and
wheel arches.
5. Remove water from the surface of the car with the scraper
on the car brush. Make sure that all grains of sand etc. have
been removed before using the scraper. Wipe with a wash lea-
ther where the scraper cannot reach.
Rims, alu- Rim brush,
Apply Alu Cleaner with an automizer. Let it act for approx.
5 min. and wash with the rim brush. For steel rims, use Car Com-
bi Cleaner. Use the foam sprayer and wash with rim brush.
Be careful! The high pressure jet may damage the tyres.
minium
auto nozzle,
atomizer,
Alu Cleaner
Flagstones, Powerspeed®
concrete nozzle,
floors and Stone & Wood
other hard Cleaner,
Wash towards outlets or the like. On surfaces with moss or
algae you may start by applying Stone & Wood Cleaner with
the foam sprayer. Wash before the soap dries. Another
more effective and quicker method is to use the Patio
Cleaner. Thus you will also avoid splashes.
surfaces
Patio Cleaner
Garden
furniture,
wood
Wood Cleaner
Garden brush
Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.
Brickwork, Powerspeed®
Wood work nozzle,
Stone & Wood
Same method as for flagstones, but be careful - bad joints and
wood may be damaged by high pressure.You may choose only
to use the Tornado® nozzle. Adjust the distance (pressure) to
the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.
Cleaner,
Patio Cleaner
Gutter
Underchassis spray Wash the gutter with the nozzle. Always wash towards
lance
downpipes. Beware not to spray under the roofing.
Cleaning
of drain
pipes, out-
lets, down
pipes etc.
Tube cleaner
Push the tube cleaner approx. ½ m (to mark) into a tube or drain
and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and flush the dirt backwards.
Rust, paint Water/sandblasting Mount the water/sand blasting equipment and rust and paint
equipment
is efficiently and quickly removed. Beware not to damage the
surface to be sandblasted.
Green-
house
Tornado® PR nozzle Wash with high pressure and maybe a brush.You may use Stone
brush, Stone &
Wood Cleaner
& Wood Cleaner to remove moss and algae.
Garden
Tornado® PR noz-
Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with
the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle.You may use the multiangle adaptor for hard to get at
areas to avoid splashing.
tools, lawn zle, Powerspeed®
mover
nozzle, multiangle
adaptor, Metal
Cleaner
10
EN
6 After using your pressure washer
6.1 Storing the washer
The machine should be sto-
red in a frost-free room!
3. Stop the machine, unplug
and wind up hose and cable.
4. Place spray handle, nozzles
and other accessories in the
holders of the machine.
Pump, hose and accessories
should always be emptied of
water prior to storing as follows:
Should the machine by mistake
be frozen, it will be necessary
to check it for damage.
ꢀ
1. Stop the machine (press the
start/stop switch “O” (1) and
detach water hose and ac-
cessory.
2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
gun.
NEVER START-UP A FROZEN
MACHINE.
Frost damages are not
covered by the guarantee!
6.2 Winding up of electric
cable and high pressure
hose
To avoid accidents, the electric
cable and the high pressure
hose should always be winded
carefully up.
1. Wind up the electric cable on
the appropriate hooks.
The high pressure washer
comes in two models: A) with
hook for storage of high pres-
sure hose (14) - B) with a hose
reel (13), where the hose is
pushed into the reel and after-
wards winded up.
11
6.3 Storage of accessories
The standard accessories
(spray gun and spray lance (a),
nozzles (b) foam sprayer (c))
can be stored on the pressure
washer.
The nozzle cleaning tool (d)
and a Click & Clean brush
(e) can also be stored on the
product.
EN
A
B
D
C
B
D
A
C
7 Maintenance
WARNING! Always disconnect ꢁWash out water hose, high
the electrical plug from the
socket prior to maintenance or
cleaning.
pressure hose, spray lance
and accessories before
mounting.
ꢁClean the connectors of dust
and sand.
To ensure a long and problem
free working life, please take
the following advice:
ꢁMake sure that no sand or
dirt is blocking the movement
of the pawl on the Click &
Clean spray lance. Rinse ac-
cording to requirement.
ꢁRinse the detergent spraying
attachment after use.
ꢁClean the nozzles.
Any repair should always be
made in an authorized work-
shop with original spare parts.
12
7.1 Cleaning of water inlet
filter
Clean the water inlet filter
regularly once a month or more
frequently according to use.
Carefully loosen the filter with a
pair of pliers and clean it. Check
that it is intact before re-mount-
ing it.
EN
The inlet filter must always be
fitted inside the water inlet pipe
to filter out sand, limestone and
other impurities, as they will
damage the pump valves.
CAUTION: Failure to fit the filter
will invalidate the guarantee.
7.2 Cleaning of nozzle
A clogging up in the nozzle
causes a pump pressure which
is too high. This is why cleaning
is required immediately.
1. Stop the machine and dis-
connect the nozzle.
2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!
3. Flush the nozzle backwards
with water.
7.3 Cleaning of machine
vents
The machine should be kept
clean so as to let cooling air
pass freely through the ma-
chine vents.
7.4 Greasing of couplings
To ensure an easy connec-
tion and that o-rings do not dry
up, the couplings should be
greased regularly.
13
EN
8 Trouble-shooting
To avoid unnecessary disappointments, you should check the following before contacting the Nilfisk-
ALTO service organization:
Symptom
Cause
Recommended action
Machine refuses to start Machine not plugged in
Defective socket
Plug in machine.
Try another socket.
Replace fuse. Switch off other machines.
Try without the extension cable.
Fuse has blown
Defective extension cable
Fluctuating pressure
Pump sucking air
Check that hoses and connections are air-
tight.
Valves dirty, worn out
or stuck
Pump seals worn out
Clean and replace or refer to local Nilfisk
ALTO distributor
Clean and replace or refer to local Nilfisk-
ALTO distributor.
Motor busses
Machine stops
Low voltage or
low temperature
Activate the trigger of the spray gun.
Fuse has blown
Incorrect mains voltage
Replace fuse. Switch off other machines.
Check that the mains voltage corresponds
to specification on the model tag.
Leave the washer for 5 minutes to cool
down.
Thermal sensor activated
Nozzle partially blocked
Fuse too small
Clean the nozzle (see section 7.2)
Fuse blows
Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.
Machine pulsating
Air in inlet hose/pump
Allow machine to run with open trigger until
regular working pressure resumes.
Check that the water supply corresponds to
specifications required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Clean the nozzle (see section 7.2)
Clean the filter (see section 7.1)
Inadequate supply of
mains water
Nozzle partially blocked
Water filter blocked
Hose kinked
Straighten out hose.
Machine often starts
and stops by itself
Pump/spray gun is
leaking
Contact your nearest Nilfisk-ALTO Service
Centre.
Machine starts, but
no water comes out
Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
frozen
No water supply
Water filter blocked
Nozzle blocked
Connect inlet water.
Clean the filter (see section 7.1)
Clean the nozzle (see section 7.2)
In case problems other than the above occur, please contact your local Nilfisk-ALTO distributor.
14
EN
9 Further information
9.1 Recycling the washer
Make the old cleaner unusable
immediately.
cal and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.
1. Unplug the cleaner and cut
the electric cable.
Contact your local authorities or
your nearest dealer for further
information.
Do not discard electrical appli-
ances with household waste.
As specified in European Direc-
tive 2002/96/EC on old electri-
9.2 Warranty conditions
Nilfisk-ALTO guarantees high
pressure washers for domestic
use for 2 years. If your high
Repairs under this guarantee
include replacement of defec-
tive parts, exclusive of packing
pressure washer or accessories and postage/carriage. Besides,
are handed in for repair, a copy we refer to your national law of
of the receipt must be enclosed. sale.
Guarantee repairs are being
made on the following condi-
tions:
The machine should be for-
warded to one of the service
centres of the Nilfisk-ALTO
organisation with description/
specifi cation of the fault.
ꢁthat defects are attributable
to flaws or defects in materi-
als or workmanship. (wear
and tear as well as misuse
are not covered by the guar-
antee).
Repairs not covered by the
guarantee conditions will be
invoiced. (I.e. malfunctions due
ꢁthat the directions of this
instruction manual have been to Causes mentioned in section
thoroughly observed.
ꢁthat repair has not been car-
ried out or attempted by oth-
er than Nilfisk-ALTO-trained
service staff.
Troubleshooting Chart of the
instruction manual).
In order that Nilfisk-ALTO
can render you optimum
service, you should register
your product on our web site
ꢁthat only original accessories
have been applied.
exposed to abuse such as
knocks, bumps or frost.
“PRODUCT REGISTRATION”.
ꢁthat only water without any
impurities has been used.
ꢁthat the high pressure wash-
er has not been used for
rental nor used commercially
in any other way.
15
9.3 Accessories
EN
Only use original accessories.
Click & Clean
Car nozzle
Special nozzle for enameled surfaces. Optimal distance: 30
- 50 cm.
Click & Clean
Undershassis
nozzle
90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.
Click & Clean
Multiangle
adaptor
Adjusted in angles from 0° - 90° for better working posture and
cleaning of hard to get at places as for instance barrels or the
underside of the lawn mower. Fits all nozzles.
Click & Clean
Brushes
For cars and other surfaces. Available in more shapes.
Extension hose
7 m extension hose increasing the working range.
Special spray lance for washing your car underneath.
Underchassis
spray lance
Drain & Tube
cleaner
15 m long tube cleaner for the cleaning of tubes and drains.
Water-sand-
blasting equip-
ment
For removal of paint and rust. Sand available from do-it-your-
self shops.
Patio Cleaner
Equipment for quick cleaning of patio/drive/flagstones.
Garden brush
Rim brush
Rotating brush for cleaning of wooden surfaces.
Rotating brush for cleaning of wheel rims.
Wall accessos-
ries storage
Rack for storage of hose, spray handle, nozzles etc.
Wall hook
For suspension of your high pressure washer on the wall.
For cleaning vehicles and other surfaces.
Rotary brush
16
Detergents
EN
Stone & Wood Cleaner
Plastic Cleaner
For flagstones, brick- and woodwork. Suitable for moss and algae.
For plastic and synthetic materials such as garden furniture.
For cleaning of metal such as garden tools.
Metal Cleaner
Car Combi Cleaner
Alu Cleaner
For cars etc. With rinsing wax.
For surfaces of aluminium. Applied with an atomizer.
Oil & Grease Cleaner
For cleaning of grease and oil on motors for instance. Applied with
an atomizer.
Wood Cleaner
For cleaning of wooden surfaces incl. of wooden garden furniture.
10 EU Declaration of Conformity
EU Declaration of Conformity
Product:
High Pressure Washer
Nilfisk-ALTO E 130.1, E 140.1
230 V 1~, 50 Hz - IP X5
EC Machine Directive
Type:
Description:
The design of the unit corres-
98/37/EC
73/23/EEC
89/336/EEC
ponds to the following pertinent EC Low-voltage Directive
regulations: EC EMV Directive
Applied harmonised standards: EN 60335-2-79
Applied national standards and IEC 60335-2-79
technical specifications:
Nilfisk-ALTO
Division of Nilfisk-Advance A/S
Industrivej 1
DK-9560 Hadsund
Anton Sørensen
V.P. Technical Operations Europe Hadsund, 01.11.2004
17
FRANCE
Fax: +48 22 738 37 51
E-mail: info@nilfisk-alto.pl
Nilfisk-ALTO
ALTO France SAS
Aéroparc 1
19 rue Icare
67960 Entzheim
Tel.: +33 3 88 28 84 00
Fax: +33 3 88 30 05 00
E-mail: info@nilfisk-alto.fr
PORTUGAL
Nilfisk-ALTO
Division of Nilfisk-Advance Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edificio 1, 1° A
P2710-089 Sintra
GERMANY
Tel.: +35 808 200 537
Fax: +35 121 911 2679
E-mail: mkt@nilfisk-advance.es
Nilfisk-ALTO
Division of Nilfisk-Advance AG
Guido-Oberdorfer-Strasse 10
89287 Bellenberg
HEAD QUARTER
RUSSIA
Tel.: +49 0180 5 37 37 37
Fax: +49 0180 5 37 37 38
E-mail: info@nilfisk-alto.de
Nilfisk-Advance LLC
Vyatskaya str. 27, bld. 7
127015 Moskow
DENMARK
Nilfisk-Advance Group
Sognevej 25
Tel.: +7 495 783 96 02
Fax: +7 495 783 96 03
E-mail: info@nilfisk-advance.ru
DK-2605 Brøndby
GREECE
Tel.: +45 4323 8100
Fax: +45 4343 7700
E-mail: mail@nilfisk-advance.dk
Nilfisk-Advance SA
8, Thoukididou str.
SINGAPORE
164 52 Argiroupolis
Tel.: +30 210 96 33443
Fax: +30 210 96 52187
E-mail: nilfi[email protected]
Nilfisk-Advance Pte. Ltd.
Nilfisk-ALTO Division
40 Loyang Drive
Singapore 508961
SALES COMPANIES
Tel.: +65 6 759 9100
Fax: +65 6 759 9133
E-mail: sales@nilfisk-advance.com.sg
HOLLAND
Nilfisk-ALTO
AUSTRALIA
Division of Nilfisk-Advance BV
Camerastraat 9
3322 BB Almere
Tel.: +31 36 546 07 60
Fax: +31 36 546 07 61
E-mail: info@nilfisk-alto.nl
Nilfisk-ALTO
SPAIN
48 Egerton St.
Nilfisk-ALTO
P.O. Box 6046
Division of Nilfisk-Advance S.A.
Torre D’Ara
Silverwater, N.S.W. 2128
Tel.: +61 2 8748 5966
Fax: +61 2 8748 5960
Paseo del Rengle, 5 Pl. 10
08302 Mataró
Tel.: +34 902 200 201
Fax: +34 93 757 8020
E-mail: mkt@nilfisk-advance.es
AUSTRIA
HONG KONG
Nilfisk-Advance GmbH
Nilfisk-ALTO
Nilfisk-Advance Ltd.
2001 HK Worsted Mills Ind’l Bldg.
31-39 Wo Tong Tsui St.
Kwai Chung
Metzgerstrasse 68
5101 Bergheim/Salzburg
Tel.: +43 662 456 400-0
Fax: +43 662 456 400-34
E-mail: info@nilfisk-alto.at
SWEDEN
ALTO Sverige AB
Tel.: +852 2427 5951
Fax: +852 2487 5828
Member of Nilfisk-Advance Group
Aminogatan 18, Box 4029
431 04 Mölndal
HUNGARY
Tel.: +46 31 706 73 00
Fax: +46 31 706 @nilfisk-alto.se
Nilfisk-Advance Kereskedelmi Kft.
II. Rákóczi Ferenc út 10
2310 Szigetszentmiklos-Lakihegy
Tel: +36 2447 5550
CANADA
Clarke Canada
Part of the Nilfisk-Advance Group
4080 B Sladeview Crescent, Unit 1
Mississauga, Ontario L5L 5Y5
Tel.: +1 905 569 0266
TAIWAN
Fax: +36 2447 5551
E-mail: info@nilfisk-advance.hu
Nilfisk-Advance Taiwan Branch
No. 5, Wan Fang Road
Taipei
Fax: +1 905 569 8586
Tel.: +886 227 002 268
Fax: +886 227 840 843
ITALY
CHINA
Nilfisk-ALTO
Nilfisk-Advance (Shenzhen) Ltd.
Blok 3, Unit 130 1001 Honghua Road
Int. Commercial & Trade Ce nter
Fuitian Free Trade Zone
518038 Shenzhen
Divisione di Nilfisk-Advance A/S
Località Novella Terza
26862 Guardamiglio (LO)
E-mail: d.puglia@nilfisk-advance.it
THAILAND
Nilfisk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Layao, Jatuchak, Bangkok 10900
Tel.: +66 2 275 5630
Tel.: +86 755 8359 7937
Fax: +86 755 8359 1063
JAPAN
Nilfisk-Advance Inc.
247 Nippa-cho, Kouhoku-ku
Yokohama, 223-0057
Tel.: +8145 548 2571
Fax: +8145 548 2541
Fax: +66 2 691 4079
CZECH REPUBLIC
ALTO Ceská Republika s.r.o.
Zateckých 9
UNITED KINGDOM
Nilfisk-ALTO
Division of Nilfisk-Advance Ltd.
Bowerbank Way
Gilwilly Industrial Estate, Penrith
Cumbria CA11 9BQ
Tel.: +44 1 768 86 89 95
Fax: +44 1 768 86 47 13
E-mail: sales@nilfisk-alto.co.uk
14000 Praha 4
Tel.: +420 24 14 08 419
Fax: +420 24 14 08 439
E-mail: [email protected]
MALAYSIA
Nillfisk-Advance Sdn Bhd
Sd 14, Jalan KIP 11
Taman Perindustrian KIP
Sri Damansara
DENMARK
Nilfisk-ALTO
52200 Kuala Lumpur
Tel.: +60 3 603 6275 3120
Fax: +60 3 603 6274 6318
Division of Nilfisk-Advance A/S
Industrivej 1
USA
9560 Hadsund
ALTO Cleaning Systems Inc.
Part of the Nilfisk-Advance Group
12249 Nations Ford Rd.
Pineville, North Carolina 28134
Tel.: +1 704 971 1240
Tel.: +45 7218 2100
Fax: +45 7218 2105
E-mail: salg@nilfisk-alto.dk
E-mail: service@nilfisk-alto.dk
NORWAY
Nilfisk-Advance AS
Bjørnerudveien 24
1266 Oslo
Tel.: +47 22 75 17 70
Fax: +47 22 75 17 71
E-mail: info@nilfisk-alto.no
Fax: +1 704 971 1241
E-mail: info@nilfisk-advance.us
Nilfisk-ALTO Food division
Division of Nilfisk-Advance A/S
Blytækkervej 2
VIETNAM
Nilfisk-Advance Representative Office
No. 46 Doc Ngu Str.
Ba Dinh Dist.
9000 Aalborg
POLAND
Tel.: +45 7218 2100
Nilfisk-Advance Sp. Z.O.O.
05-800 Pruszków
ul. 3-go MAJA 8
Fax: +45 7218 2099
Hanoi
E-mail: scanio.technology@nilfisk-alto.dk
Tel.: +84 4 761 5642
Fax: +84 4 761 5643
E-mail: nilfi[email protected]
Tel.: +48 22 738 37 50
126487135
|