BES50_QuickInstallGuide4.pdf
9/13/2006
3:12:23 PM
Busin
Quick Install Guide
B
ess
E
Eth
S
ern
5
et Switch 50 Series
0
17
192.168.1.255 and then
click OK.
Note: By default the
Read Community is
“PlsChgMe!RO” and the
Write Community is
“PlsChgMe!RW”.
Steps 11 13
Powering up
Steps 4 10
17. Enter the range
192.168.1.1 to
Mounting Options
Perform steps 11 and
12 in the order listed.
!
You can download all documents
referenced in this Quick Install guide at
The BES50FE12/24T and BES50GE12/24T switch units can be
mounted horizontally on a flat surface and stacked with a BCM50.
11. Insert the power adapter
into the DC power socket in the
front of the switch.
4. If you mount a BES50 unit on a desktop or shelf,
attach the supplied rubber feet to the bottom of the
unit. If the BES50 system includes additional units,
you can set the additional units beside, or stack
them on top of, the first unit.
Steps 1 3
11
4
Before you
1
start
18. Select the BES device from the list of
network elements on the Element Manager
tree.
1. Download the Business Element
12
Manager 1.0 Installer to a
computer on your network.You
install the Element Manager in
Step 16.
18
19
5. If you are mounting the additional units
beside the first unit, attach the supplied
rubber feet to the bottom of each unit.
12. Plug the other end
of the power adapter
into a grounded, 3-pin
socket, AC power
source.
5
19. Click the Web Page button on the
Element Manager menu.
6. If you are stacking the additional units on top of
the first unit, mount each unit into the tabs on top
2
6
20. Enter the default username
of another unit.
2. Confirm that you have the tools and
package contents as follows:
Tools Required:
(nnadmin) and password
20
(PlsChgMe!) to log on to the
BES50.
13
a. Phillips or flathead screwdriver, depending
on the type of screws used.
Package contents:
b. BES50FE-12/24T PWR or
BES50GE-12/24T PWR switch
c. Adhesive foot pads (4)
d. AC power adapter
C
M
7
13. Check the front-panel LEDs as the device
powers on to confirm that the PWR LED is green.
If not, check that the power cable is correctly
plugged in.
21
7. If you mount the switch on a
desktop or flat surface, attach the
four adhesive feet to the device as
indicated.
Y
21. From the main menu, choose Administration > Quick Start. The
Quick Start screen appears showing the IP address and other items that
you can optionally configure. If you want to manually assign IP addresses,
CM
MY
CY
CMY
K
The BES50 series switch performs a short self-test
as soon as you connect the switch to the power
supply. The status LED will flash green during the
self-test, then solid green when finished. If the
Status LED turns off, the device is not working
correctly. When the self-test finishes, the BES50
starts switching data.
a. Set the device on a flat surface near an AC power source, making
sure there are at least two inches of space on all sides for proper air flow.
b. If you install multiple switches, attach four adhesive feet to each one.
Place each device squarely on top of the one below, in any order.
BES50-FE/GE-12T PWR switch
System Indicators
Port/PoE Status Indicators
8. To install a BCM50 unit on top of a BES50 unit, place
the BCM50 unit on top of the BES50.
RJ-45 Ports with PoE
8
InSitteipasl14Ac2c1 ess and
Configuration
BES50-FE/GE-24T PWR switch
System Indicators
Port/PoE Status Indicators
9. Make sure the feet of the BES50 are in the slots
on the top of the BCM50 unit and in front of the slots
9
14
10. Slide the unit back until it clicks in place on
RJ-45 Ports with PoE
RJ-45 Ports
the slots.
14. To access the BES50, first install the Business Element
Manager 1.0. Refer to Element Manager documentation at
10
3. Check your cables; when you install
the switch into a network make sure you
use the following required cables:
3
15. Start the Element Manager.
• Category 3 UTP or STP cables with an RJ-45 connector
(for 10BASE-T ports).
You are now ready to use the BES50 series switch in
your network installation.
15
Slots
Feet
• Category 5 UTP or STP cables with an RJ-45 connector
(for 100BASE-TX ports).
• Category 5, 5e, or 6 UTP or STP cables with an RJ-45
connector (for 1000BASE-T ports).
16. From the Element Manager
Refer to Using the Nortel Business Ethernet Switch 50
instructions.When you connect a PC directly to the
BES50, use the default IP address 192.168.1.128
menu, choose Network > Find
16
Network Elements > Business
Ethernet Switch.
N0128198
|