CD Receiver System
CS-245BT
CD Receiver (CR-245BT)
Speakers (D-T05)
Instruction Manual
Playing Your
Bluetooth .................................22
Playing a
Thank you for purchasing an Onkyo CD Receiver System.
Please read this manual thoroughly before making any
connections and plugging it in.
Following the instructions in this manual will enable you to
obtain optimum performance and listening enjoyment from
your new CD Receiver System.
Please retain this manual for future reference.
En
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal
without the permission of the copyright holder.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
• When you’ve finished using this unit, remove all
discs and turn off the power.
9. Installing this Unit
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they
may damage the finish or remove the panel lettering.
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
10. Moisture Condensation
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do
not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an
extended period, remove the power cord from the
AC outlet.
– In the summer, when this unit is moved from
an air conditioned room to a hot and humid
place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
If condensation does occur, unplug the power cord
and leave the unit for two to three hours in the room
temperature.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
8. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
3
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Hereby, Onkyo Corporation, declares that this
CR-245BT is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
С настоящето, Onkyo Corporation, декларира, че
CR-245BT е в съответствие със съществените
изисквания и другитеприложими разпоредби на
Директива 1999/5/EC.
The label on the right is
applied on the rear panel.
1. This unit is a CLASS 1
Onkyo Corporation tímto prohlašuje, že CR-245BT
splňuje základní požadavky a všechna příslušná
ustanoveni Směrnice 1999/5/ES.
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified
personnel.
Undertegnede Onkyo Corporation erklærer herved,
at følgende udstyr CR-245BT overholder de
væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
Hiermit erklärt Onkyo Corporation, dass sich das
Gerät CR-245BT in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/
5/EG befindet.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Käesolevaga kinnitab Onkyo Corporation seadme
CR-245BT vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
Blue:
Brown:
Neutral
Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo
Corporation ∆ΗΛΩΝΕΙ ΟΤΙ CR-245BT
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ
Por la presente, Onkyo Corporation, declara que
este CR-245BT cumple con los requisitos
esenciales y otras exigencias relevantes de la
Directiva 1999/5/EC.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
Par la présente, Onkyo Corporation déclare que
l’appareil CR-245BT est conforme aux exigences
essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE.
Con la presente Onkyo Corporation dichiara che
questo CR-245BT è conforme ai requisiti essenziali
ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
For European Models
Ar šo Onkyo Corporation deklarē, ka CR-245BT
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.
Šiuo Onkyo Corporation deklaruoja, kad šis
CR-245BT atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
A Onkyo Corporation ezzennel kijelenti, hogy a
CR-245BT típusú beren-dezés teljesíti az alapvető
követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.
4
Hierbij verklaart Onkyo Corporation dat het toestel l
CR-245BT in overeenstemming is met de
essentiële eisen en de andere relevante bepalin-
gen van richtlijn 1999/5/EG.
Before Using Your New Speakers
• Place the speakers on sturdy, flat surfaces. Putting
them on uneven or unstable surfaces where they may
fall and cause damage will affect the sound quality.
• Do not keep water or other liquids close to the
speakers. If a liquid is spilled over them, the woofer
and tweeter inside may be damaged.
Niniejszym Onkyo Corporation deklaruje że
CR-245BT jest zgodny z zasadniczymi
wymaganiami i innymi właściwymi
postanowieniami Dyrektywy 1999/5/EC.
• Do not handle the speakers with wet or damp hands.
Eu, Onkyo Corporation, declaro que o CR-245BT
cumpre os requisitos essenciais e outras provisões
relevantes da Directiva 1999/5/EC.
Speaker Precautions
The speakers can handle the specified input power when
used for normal music reproduction. If they’re fed any
of the following signals, even if the input power is
within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2. Audio from a cassette that’s being fast-forwarded.
3. High-pitched sounds generated by an oscillator, elec-
tronic musical instrument, and so on.
Prin prezenta, Onkyo Corporation, declară că
aparatul CR-245BT este în conformitate cu
cerinţele esenţiale şi cu alte prevederi pertinente
ale Directivei 1999/5/CE.
Onkyo Corporation týmto vyhlasuje, že CR-245BT
a spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (always turn off your amplifier
before connecting or disconnecting cables).
Onkyo Corporation izjavlja, da je ta CR-245BT v
skladu z bistvenimi zahtevami in drugimi
relevantnimi določili direktive 1999/5/ES.
Onkyo Corporation vakuuttaa täten että CR-245BT
tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
7. Microphone feedback.
The speakers contain powerful magnets. Do not put
metal items, such as screwdrivers, close to the speakers,
as they may be attracted toward the magnet, causing
injury, or damage to the tweeter diaphragm.
Härmed förklarar Onkyo Corporation att denna
CR-245BT följer de väsentliga kraven och andra
relevanta stadgar i Direktiv 1999/5/EC.
Using Close to a TV or Computer
Hér með lýsir Onkyo Corporation því yfir að varan
CR-245BT er í samræmi við grunnkröfur og aðrar
kröfur sem gerðar eru í tilskipun 1999/5/EC.
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer from
discoloration or picture distortion when conventional
speakers are placed nearby. To prevent this, the speakers
feature internal magnetic shielding. In some situations,
however, discoloration may still be an issue. In this
case, turn off your TV or monitor, wait 15 to 30
minutes, and then turn it back on again. This normally
activates the degaussing function, which neutralizes the
magnetic field, thereby removing any discoloration
effects. If discoloration problems persist, try moving the
speakers away from your TV or monitor. Note that
discoloration can also be caused by a magnet or
demagnetizing tool that’s too close to your TV or
monitor.
Onkyo Corporation erklærer herved at denne
CR-245BT er i overensstemmelse med vesentlige
krav og andre relevante bestemmelser i direktiv
1999/5/EC.
Note:
• If the speakers are placed close to a TV or monitor,
due to the electromagnetic waves radiated by the TV
or monitor, you may hear noise from the speakers even
after your amplifier has been turned off. To prevent
this, position the speakers away from your TV or
monitor.
5
Package Contents
Make sure you have the following items:
When using the remote controller, point it toward the
CD receiver’s remote control sensor, as shown below.
CD Receiver (CR-245BT)
Remote controller (RC-854C)
Indoor FM antenna
CR-245BT
Remote control sensor
Power cord
(Connector type varies from country to country.)
Speakers (D-T05)
Speaker cables
8 floor pads
* In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications
and operation are the same regardless of color.
30°
30°
Using the Included Floor Pads for
speakers
Replacing the Battery
You can improve the sound quality by attaching the
included floor pads to raise the speakers off the surface
and reduce the contact area. The floor pads also make
the speakers stable and prevent them from slipping.
Use only a battery of the same type (CR2025).
Firmly insert a thin stick or similar
object into the hole, and pull out
firmly in the direction of the arrow.
Floor pads
Back side
Bottom
Positive ⊕ side
D-T05
Using the Remote Controller
Note:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or corrosion.
Remove the plastic film before using the remote
controller.
Caution:
• Replacing the battery incorrectly may cause an
explosion. Use only a battery of the same type or an
equivalent.
6
Features
General
*1.
• Super Bass (S.Bass) function for deeper bass sounds
• Bass and treble tone controls
• Line input for external audio source
• AUDIO OUT (SUBWOOFER) jack
• Headphones jack
iPad, iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and
iPod touch are trademarks of Apple Inc., registered in the U.S.
and other countries.
• Dimmable display
“Made for iPod”, “Made for iPhone” and “Made for iPad”
mean that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone or
iPad may affect wireless performance.
Speakers
• Stylish cabinet
• 2 Way Bass-reflex
iPod
*1
• iPod/iPhone/iPad direct digital connection
*2. This functionality might not be available depending on the
• Control your iPod/iPhone/iPad with the remote
controller
iPod/iPhone/iPad model or apps.
• Made for iPod touch (1st, 2nd, 3rd and 4th
generation), iPod nano (2nd, 3rd, 4th, 5th and 6th
generation), iPhone 4S, iPhone 4, iPhone 3GS,
iPhone 3G, iPhone, iPad (3rd generation), iPad 2 and
iPad
*3. Onkyo does not guarantee Bluetooth compatibility between the
CR-245BT system and all Bluetooth-enabled devices.
For compatibility between the CR-245BT system and another
device with Bluetooth technology, consult the device’s
documentation and dealer. In some countries, there may be
restrictions on using Bluetooth devices. Check with your local
authorities.
Radio
®
The Bluetooth word mark and logos are registered trademarks
• FM tuner
• 30 FM presets
• RDS (Radio Data System)
• FM Auto Preset function
owned by Bluetooth SIG, Inc . and any use of such marks by
Onkyo is under license. Other trademarks and trade names are
those of their respective owners.
Please read rating label at the bottom or rear panel of system
for other safety information.
CD Player
• Play audio CDs, MP3 CDs (CD-R and CD-RW)
• RANDOM playback mode
• 2-mode repeat function (current track or all tracks)
*4. aptX is a registered trademark of CSR plc.
USB Flash Drive
• MP3 playback from USB flash drives
Timer and Clock
• Programmable timer
• Sleep timer
• The alarm play function of the iPod/iPhone/iPad can
power-on the CD receiver and switch the input to
*
2
iPod/iPhone/iPad
Bluetooth
*3
• Wireless Music Playback via Bluetooth
• Profile: A2DP 1.2
• Audio codec: SBC, AAC and aptX
*4
7
Contents
Getting Started
Playing Your iPod/iPhone/iPad
Disc (Audio CD and MP3)
Navigating the iPod Menus
Playing Back via Bluetooth
Listening to the Radio
Presetting FM Stations Automatically
Connections
Playing a USB Flash Drive
Basic Operations
Clock and Timer
Timer Playback using the Alarm Play Function
Miscellaneous
Playing CDs
8
Display
a b c
d
e
f
g
h
i
j
k l
m
n
o
a SLEEP indicator
i TIMER indicators
j Tuning indicators
k RDS indicator
l FILE indicator
m TRACK indicator
n Message area
b Play 1 and Pause 3 indicators
c USB indicator
d Bluetooth indicators
e FOLDER indicator
f S.BASS indicator
g MUTING indicator
o DISC, TOTAL, and REMAIN indicators
h Playback mode indicators
Rear Panel
a
b
c
d
e
a FM ANTENNA jack
b LINE IN jack
c AUDIO OUT (SUBWOOFER) jack
d SPEAKERS terminals
e AC INLET
10
Disc (Audio CD and MP3) and USB Flash Drive
(MP3) Notes
Precautions for Playback
Playback from USB Flash Drives
Compact discs (CDs) with the following logo on the
label surface can be used.
MP3 files recorded on a USB flash drive can be played
with the CD receiver.
Do not use discs designed for purposes other than audio,
such as CD-ROMs for PC use. Abnormal noise could
damage the CD receiver.
• USB flash drives formatted in FAT16 or FAT32 are
supported.
• Only MP3 files with the extension “.MP3” or “.mp3”
are supported.
• Files recorded using MPEG 1 audio layer 3 at
sampling frequencies of 32/44.1/48 kHz and a
constant bit rate (CBR) of 32–320 kbps are supported.
• A maximum of 299 folders can be recognized on a
single USB flash drive. A maximum of 648 files can
be recognized in a single folder.
*
The CD receiver supports CD-R and CD-RW discs.
Note that some discs may not playback because of the disc
characteristics, scratches, contamination or the recording state.
A disc recorded with an audio CD record will not playback
unless it is finalized.
Note:
• A disc recorded with a recorder or personal computer
may not play in some cases. (Cause: Disc’s
characteristics, damaged or dirty disc, dirt on player’s
lens, dew condensation, etc.)
• A disc recorded on a personal computer may not play
because of the application settings or environment.
Record the disc with the proper format. (Contact the
application maker for details.)
Never use discs which have a special shape (such as
hearts or octagons). These types of discs could jam and
damage the CD receiver.
• A disc with insufficient storage capacity may not
playback properly.
Handling Discs
CD Playback with Copy-control Function
Hold discs by the edge, or by the center hole and edge.
Avoid touching the playback surface (surface with
nothing printed on it).
Some audio CDs with copy-control function do not
comply with official CD standards. These are special
discs and cannot be played with the CD receiver.
Label surface
(printed surface)
Playback of MP3 Discs
MP3 files recorded on a CD-R/CD-RW can be played
with the CD receiver.
• Use discs which have been recorded following the
ISO 9660 Level 2 file system. (The supported
directory depth is eight levels, the same as ISO 9660
Level 1)
• Discs recorded with the hierarchical file system (HFS)
cannot be played.
Playback surface
Do not attach paper or stickers, or write on the playback
or label surface of the disc. Take care not to scratch or
damage the disc.
Precautions for Rental Discs
• Discs must be closed (finalized).
• Only MP3 files with the extension “.MP3” or “. mp3”
are supported.
Do not use discs with residue from cellophane tape,
rental discs with labels which are peeling off, or discs
with decorative labels. This type of disc could get stuck
in the CD receiver, or could damage the CD receiver.
• Files recorded using MPEG 1 audio layer 3 at
sampling frequencies of 32/44.1/48 kHz and a
constant bit rate (CBR) of 32–320 kbps are supported.
• A maximum of 299 folders can be recognized on a
single CD. A maximum of 648 files can be recognized
in a single folder.
12
Precautions for Inkjet Printable Discs
Caring for Discs
Do not leave a CD-R/CR-RW having a label printed with
an inkjet printer in the CD receiver for a long time. The
disc could get stuck in the CD receiver, or could damage
the CD receiver.
If the disc is dirty, the CD receiver will have a hard time
reading signals, and the audio quality may drop. If the
disc is dirty, gently wipe off fingerprints and dust with a
soft cloth. Lightly wipe from the center outwards.
Remove the disc from the CD receiver when not being
played, and store it in a case. A freshly printed disc will
stick easily, and should not be played immediately.
To remove stubborn dust or dirt,
wipe the disc with a soft cloth
dampened with water, and then dry
it with a dry cloth. Do not use
cleaning spray for analog records
or antistatic agents, etc. Never use
volatile chemicals such as benzine
or paint thinner as they can impregnate the disc surface.
Connecting FM Antenna
This section explains how to connect the supplied indoor FM antenna.
The CD receiver won’t pick up any radio signals if no antenna is connected, so you must connect the antenna to use the
tuner.
Caution:
• Be careful not to injure yourself when using
thumbtacks.
Insert the plug fully into
Thumbtacks, etc.
the jack.
Indoor FM antenna (supplied)
Note:
• Once your CD receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve
the best possible reception.
Tip:
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM
antenna instead.
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available
outdoor FM antenna instead.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from
possible noise sources, such as neon signs, busy roads,
etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
Note:
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock
hazards.
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
13
■ Using a TV / FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems.
If circumstances demand it, use a TV / FM antenna
splitter, as shown.
TV / FM antenna
splitter
To CD receiver
To TV (or VCR)
Connecting Speakers
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Use the red line wires to connect the positive (+)
terminals.
Right speaker
Left speaker
• Do not connect anything other than the included
speakers (D-T05). We cannot take responsibility for
malfunctions or poor results if this CD receiver is used
with any other speakers.
Speaker
cable
• Do not connect both speaker cables to the same L or R
terminals. Do not connect more than two speaker
terminals to each speaker.
Red line side
CD receiver
Remove the precut insulation from the ends of the
speaker cables, and twist the bare wires tightly.
Push the lever to open the hole, insert the bare wire into
the hole, and then release the lever.
Make sure that the speaker terminals are gripping the
bare wires, not the insulation.
• Be careful not to short the positive and
negative wires.
Doing so may damage the CD receiver
and/or speakers.
• Connect the right speaker to the CD receiver’s right
(R) SPEAKERS terminals. Connect the left speaker to
the left (L) SPEAKERS terminals.
R
14
Connecting Other Components
CD receiver
Analog audio
cable (RCA)
Powered
subwoofer
To wall outlet
(Connector type varies from
country to country.)
e.g.,
cassette tape deck
About Connections
Connecting an Audio Playback
Device
• Before making any connections, read the manuals
supplied with your other components.
• Don’t connect the power cord until you’ve completed
and double-checked all connections.
Using a suitable cable, connect the CD receiver’s LINE
IN jacks to the OUTPUT (PLAY) jacks of your cassette
tape deck, TV, or other audio playback device.
Push plugs in all the way to make
good connections (loose connections
can cause noise or malfunctions).
Right!
Connecting the Power Cord
Connect the CD receiver’s power cord to a suitable wall
outlet.
Wrong!
Note:
• Do not use any cord other than the included power
cord.
Do not connect the included power cord to any other
device. Doing so may cause malfunctions or
accidents.
• Do not unplug the power cord from the AC INLET
while the other end of the cord is still connected to an
AC outlet. You may receive an electric shock if you
accidentally touch the internal terminals of the power
cord.
Note:
• Do not put anything on top of the CD receiver, as it
may interfere with proper ventilation.
Connecting a Powered Subwoofer
Using a suitable cable, connect the CD receiver’s
AUDIO OUT: SUBWOOFER to the input on your
powered subwoofer.
If your subwoofer is unpowered and you’re using an
external amplifier, connect the AUDIO OUT:
SUBWOOFER to the amp’s input.
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the CD receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the receiver into a different branch circuit.
• Plug the power cord into an AC outlet that is easily
accessible so that you can quickly unplug it if
necessary.
Note:
• Do not connect or disconnect the power cord while the
subwoofer is powered-on. Doing so may damage the
subwoofer. You must power-off the subwoofer before
connecting or disconnecting the power cord.
15
Basic Operations
This section describes the procedure for using the
remote controller, unless otherwise specified.
Selecting the Input Source
You can select CD, iPod (USB), FM, Bluetooth, or
LINE, which can be an external component.
Turning On the CD receiver
To select the input source, use the remote controller’s
Input Selector buttons. On the CD receiver, press the
[INPUT] button repeatedly.
Press the On/Standby [8] button.
The CD receiver comes on, and the display lights up.
The input sources are selected in the following order.
Press the On/Standby [8] button again to set the CD
receiver to Standby.
CD
iPod (USB)
FM
Bluetooth
LINE
You can also use the [8 ON/STANDBY] button on the
CD receiver.
During the use of your iPod/iPhone/iPad connected to
the CD receiver with a USB cable, if the connection
“Charging” appears on the display of the CD receiver
and your iPod/iPhone/iPad will be charged even with the
CD receiver on standby.
Adjusting the Volume
To adjust the volume, use the VOLUME [–]/[+]
buttons.
You can also use the CD receiver’s VOLUME [–]/[+]
buttons.
Tip:
Muting the CD receiver
You can temporarily mute the output of the CD receiver.
Press the [MUTING] button.
Setting Auto Standby (ASb)
The CD receiver is muted.
With Auto Standby, you can set the CD receiver so that
it will be automatically turned off and enter the standby
mode if there is no operation for 20 minutes with no
audio input.
“Muting” appears on the display for a few seconds. The
MUTING indicator flashes continuously while the CD
receiver is muted.
The default setting is “On”.
Note:
Make settings for this function while playback is
stopped.
• To unmute, press the [MUTING] button again or
adjust the volume.
• Muting is automatically cancelled when the CD
receiver is set to standby.
Press and hold down the remote
1
controller’s [SLEEP] button (about 3
seconds).
Using Headphones
If this setting is “On”, “AutoStby On” will appear
You can connect a pair of stereo headphones (ø3.5 mm,
1/8-inch phone plug) to the receiver’s headphones [=]
jack for private listening.
on the CD receiver’s display.
Note:
Note:
• To switch between “On” and “Off”, repeat this
procedure.
• With Bluetooth Standby “On”, the CD receiver will
enter the Bluetooth Standby mode if the Auto Standby
function is enabled (see page 22).
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the
headphones [=] jack, the speakers are turned off.
16
Adjusting the Bass and Treble
Press the [BASS] or [TREBLE] button, and then
use the [q]/[w] buttons to adjust the bass or
treble, respectively.
The default setting is “0”. You can adjust the bass and
treble from –5 to +5.
While adjusting the bass or treble, you can press the
[CLEAR] button to return the setting to “0”.
Note:
• If you press no buttons for about 5 seconds, the
previous display will appear automatically.
Using Super Bass
To turn on Super Bass, press the [S.BASS]
button.
The setting will alternate between S.Bass Off, S.Bass 1,
and S.Bass 2 each time you press the button.
To turn off Super Bass, press the [S.BASS] button
repeatedly until “S.Bass Off” appears.
The default setting is “Off”.
Changing the Display Brightness
You can adjust the brightness of the display.
Press the [DIMMER] button repeatedly to select:
dim, or normal brightness.
17
Playing CDs
Selecting Tracks
This section describes the procedure for using the
remote controller, unless otherwise specified.
To return to the beginning of the track currently playing,
press the Previous [7] button.
Playing CDs
Press the Previous [7] button repeatedly to select
earlier tracks.
Press the CD receiver’s [0] button to open
Press the Next [6] button repeatedly to select
1
Tip:
the disc tray.
subsequent tracks.
• Pressing the [0] button while the CD receiver is on
Standby will turn on the CD receiver and open the disc
tray.
Displaying CD Information
During playback or while playback is paused, press the
[DISPLAY] button repeatedly to display the following
CD information.
• Elapsed time
• “REMAIN”
Place CD on the tray with the label-side
facing up.
Place 8 cm CDs in the center of the tray.
2
Lights up while the remaining track time is being
displayed.
• “TOTAL REMAIN”
Lights up while the remaining disc time is being
displayed.
• Type of CD
To start playback, press the CD receiver’s
3
[1/3] button.
Alternatively, press the remote controller’s [CD]
button followed by the [1/3] button.
The disc tray closes and playback starts.
Then the “1” indicator appears.
To stop playback:
Press the [2] button.
Playback stops automatically when the last track has
been played.
To pause playback:
Press the [1/3] button. The Pause “3” indicator
appears. To resume playback, press the [1/3] button
again.
To Fast-Forward or Fast-Reverse:
During playback, press and hold the Fast Forward [4]
button to fast forward, or the Fast Reverse [5] button
to fast reverse.
To remove the CD:
Press the CD receiver’s [0] button to open the disc tray.
■ Information Displayed When Playback is
Stopped:
• Audio CD
“DISC TOTAL” lights up
CD „„ „„19„† „„67„‡29
Total number of tracks
Total playing time
18
■ Pausing Playback
Selecting MP3 Files
To pause playback, press the Play/Pause [1/3] button.
The files on an MP3 CD can be located at the disc’s root
level or within a folder.
To resume playback, press it again.
■ Selecting a higher or lower folder
Press the [e] button to select a higher-level folder, or the
[r] button to select a lower-level folder.
A folder can contain additional folders, with other
folders inside them in a hierarchical structure.
A maximum of 648 files and folders (total) can be shown
within a folder. Files and folders are listed alphabetically
without distinction.
■ To return to the root
Press the [MODE] button, and then press the [MENU]
button.
If you don’t select a specific MP3 file or folder for
playback, all of the MP3 files will be played in numerical
order starting with file #1.
Displaying MP3 Information
If random playback is selected, the files will not be
played in the numerical order. If you want the files to
play in the numerical order, you must cancel random
You can display various information about the MP3 file
currently playing, such as title, artist, and album.
During playback, press the [DISPLAY] button
repeatedly to display the following MP3
information.
While playback is stopped, press the
1
[MODE] button.
The information is shown in the following order.
“FOLDER” will light, and the name of the first
folder will be shown.
Elapsed time: The length of time that the current MP3
file has been playing (default display).
Use the arrow [q]/[w] buttons to select a
2
Remain time: The length of remaining time for the
current MP3 file.
folder.
Press the [ENTER] button or the [r] button to
File name: Name of the current MP3 file.
enter the folder.
Folder name: Name of the current folder.
Repeat this operation to select the desired folder.
When the “
” message is shown, you can press
Sampling rate and Bit rate: Sampling rate and Bit rate
of the current MP3 file.
the [ENTER] button to return to the upper-level
folder.
Volume label: Title of the current disc.
Use the arrow [q]/[w] buttons to select the
MP3 files within the folder.
3
4
Note:
• Only single-byte alphanumeric characters can be
shown.
• A folder name, file name, or volume label that
contains anything other than single-byte alphanumeric
characters might be garbled.
The name of the MP3 file inside the folder is
displayed.
To select a different folder, press the [e]/[r]
button, then use the [q]/[w] buttons to select the
desired folder, and finally press the [ENTER]
button. Use the [q]/[w] buttons to select the
desired file.
To start playback, press the [ENTER] button
or Play/Pause [1/3] button.
Playback will start with the specified file and
continue until all of the MP3 files have been
played.
To select an MP3 file in another folder during
playback, press the [MODE] button, select the
folder by using the arrow [e]/[r]/[q]/[w] buttons,
and then press the [ENTER] button. Now use the
arrow [q]/[w] buttons to select the MP3 files
within that folder.
19
Random Playback
Repeat Playback
With random playback, all of the tracks on the disc are
played in random order.
With repeat playback, you can play an entire CD
repeatedly or play one track repeatedly.
Random playback can also be used in conjunction with
repeat playback.
Repeat playback can also be used in conjunction with
random playback.
Note:
Press the [REPEAT] button repeatedly until the
REPEAT or REPEAT 1 indicator appears.
• In the case of MP3 files, the same song might be
played.
“REPEAT” will repeatedly play all songs.
Random playback can be set when the input source is set
to CD or USB.
“REPEAT 1” will repeatedly play the currently-playing
song or the selected song.
Press the [SHUFFLE] button until the
RANDOM indicator appears.
1
Note:
• If REPEAT 1 is selected, pressing the [SHUFFLE]
button will cancel “REPEAT 1”; random playback
will occur.
To start random playback, press the Play/
2
Pause [1/3] button.
■ Cancelling Random Playback
To cancel random playback, press the [SHUFFLE] or
[CLEAR] button.
■ Cancelling Repeat Playback
To cancel repeat playback, press the [REPEAT] button
repeatedly until both the REPEAT and REPEAT 1
indicators disappear.
When playing a CD, random playback will be cancelled
automatically when the CD is removed.
When playing a CD, repeat playback will be cancelled
automatically when the CD is removed.
20
Playing Your iPod/iPhone/iPad
Tip:
This section describes the procedure for using the
• When connecting your iPod/iPhone/iPad with a USB
cable, we recommend you use an official USB cable
from Apple Inc.
remote controller, unless otherwise specified.
• Before using your iPod/iPhone/iPad with the CD
receiver, be sure to update your iPod/iPhone/iPad with
the latest software, available from the Apple Web site.
• Depending on your iPod/iPhone/iPad, or the type of
content being played, some functions may not work as
expected.
Press the Play/Pause [1/3] button.
3
Playback starts.
■ Pausing Playback
To pause playback, press the Play/Pause [1/3] button.
Playing an iPod/iPhone/iPad via USB
Press the Play/Pause [1/3] button again to resume
playback. You can also pause playback by pressing the
[2] button.
■ Selecting Tracks
To return to the beginning of the track that’s currently
playing or paused, press the Previous [7] button.
Press the Previous [7] button repeatedly to select
earlier tracks.
Press the Next [6] button repeatedly to select
subsequent tracks.
■ Fast-Forward or Fast-Reverse
During playback, press and hold the Fast Forward [4]
button to fast forward, or the Fast Reverse [5] button
to fast reverse.
■ Random Playback
Press the [SHUFFLE] button repeatedly to switch the
Compatible iPod/iPhone/iPad models
Made for:
random function of your iPod/iPhone/iPad.
iPod touch (1st, 2nd, 3rd and 4th generation), iPod nano
(2nd, 3rd, 4th, 5th and 6th generation), iPhone 4S,
iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPad (3rd
generation), iPad 2 and iPad
■ Repeat Playback
Press the [REPEAT] button repeatedly to switch the
repeat function of your iPod/iPhone/iPad.
■ Selecting Playlist
Press the PLAYLIST [q]/[w] button to select the
Press the [iPod] button.
Alternatively, you can use the CD receiver’s
[INPUT] button.
playlist.
1
Navigating the iPod Menus with the
Remote Controller
Note:
• If “USB” appears on the display of the CD
receiver, the connection mode is set to USB.
Press and hold the [MODE] button until “iPod”
appears to switch the connection mode to iPod.
And then reconnect your iPod/iPhone/iPad with a
USB cable.
Press the [MENU] button to display the iPod
menu.
1
Use the Arrow [q]/[w]/[e]/[r] buttons to
2
select an item on the menu, and then press
the [ENTER] button.
Connect the USB cable that comes with the
iPod/iPhone/iPad to the USB port on the
front of the CD receiver.
2
Note:
• The volume level is adjusted by using the VOLUME
[–]/[+] buttons on the CD receiver or its remote
controller. Adjusting the volume on your iPod/iPhone/
iPad has no effect.
While reading the contents of your iPod/iPhone/
iPad, the message “Connecting” appears on the CD
receiver’s display.
“iPod” appears on the display of the CD receiver. If
your iPod/iPhone/iPad is not connected properly,
“No Device” appears.
21
Playing Back via Bluetooth
Listening to an audio from Bluetooth
device
Select the desired music and press “1/3”
button on your device. The CD receiver
automatically starts playing the audio.
appears on the display of the CD receiver after 2
minutes have elapsed after “Pairing...” appears, this
means that the pairing is not done successfully.
Perform the above procedure 1 to 4 again.
5
Note:
If the “
” indicator is not lit and “Bluetooth”
• If your mobile phone supports A2DP protocol, its
music will play through the CD receiver.
• You can build a Bluetooth connection with a mobile
phone, an iPod or any other Bluetooth-enabled
devices.
Note:
Press the [INPUT] button on the top panel
• If there is no sound output even after the paring is done
successfully, consult the user manual of the Bluetooth-
enabled device, and then select the
“Onkyo CR-245BT” as the audio output device.
• The CD receiver can store the pairing information of
up to 8 Bluetooth devices. If the pairing is done for the
ninth Bluetooth device, the pairing information of
device connected via Bluetooth in the most past times
is erased.
1
repeatedly to select the “Bluetooth” input.
Tip:
• Alternatively, you can use the remote controller’s
[ /LINE] button.
Press the [ Bluetooth PAIRING] button on
the top panel. to put the CD receiver into the
pairing mode.
2
“Pairing...” appears on the CD receiver’s display.
If you hold the [ Bluetooth PAIRING] button for
more than 2 seconds during the process of pairing,
the operation will be cancelled.
• The multiple Bluetooth devices cannot be connected
at the same time.
Displaying Bluetooth Information
If you press the [DISPLAY] button during the Bluetooth
connection, the following Bluetooth information
appears.
During this period, you can operate the
mobile phone, iPod or Bluetooth-enabled
device to pair with the CD receiver within a
10m range.
For details on the Bluetooth connection, refer to the
user manual of the Bluetooth-enabled device.
The CD receiver may not work as normal
depending on the circumstance even though the CD
receiver is placed within the 10 m range. In such
cases, get the Bluetooth-enabled device closer to
the CD receiver and retry the operation.
3
The information is shown in the following order.
• Audio CODEC
• Sampling frequency
Setting Bluetooth Standby
With Bluetooth Standby, you can set the CD receiver so
that it will be automatically turned on if the Bluetooth
device is operated while the CD receiver is on standby.
The default setting is “Off”.
Once the CD receiver is detected and its
name “Onkyo CR-245BT” appears on the
display of your Bluetooth-enabled device,
select the “Onkyo CR-245BT.” If a prompt
requests a password, key in the “0000”.
When a Bluetooth connection is established
4
Make settings for this function while CD receiver is in
standby mode.
Press and hold the [8 ON/STANDBY] button on
the CD receiver while it is on standby (about 3
seconds).
successfully, the “
” indicator will be solid on
and “Bluetooth” appears on the display of the CD
receiver.
The SLEEP indicator will be dimly-lit.
Note:
• To switch between “On” and “Off” , repeat this
procedure.
22
Listening to the Radio
This section describes the procedure for using the
remote controller, unless otherwise specified.
Presetting FM Stations Automatically
(Auto Preset)
With the Auto Preset function, you can automatically
preset all of the FM radio stations available in your area
in one go. Presets make it easy to select your favorite
stations and eliminate the need to tune the radio
manually each time you want to change stations.
Tuning into FM Radio Stations
When tuned to a station, the Tuned (
) indicator
appears. When receiving a stereo FM signal, the FM ST
indicator appears as well.
The [MODE] button is used to select Auto mode or
Mono mode. In Auto mode, the output will be stereo or
mono depending on the station being received. In Mono
mode, the output will be mono regardless of the station.
As an alternative to this Auto Preset function, there’s
also a Manual Preset function that lets you manually
preset individual FM stations (see page 24).
Auto Preset Caution!
Press the [TUNER] button to select “FM”.
Alternatively, you can use the CD receiver’s
[INPUT] button.
1
Any existing presets will be deleted when the Auto
Preset function is run.
Press the [TUNER] button to select “FM”.
Alternatively, you can use the CD receiver’s
[INPUT] button.
Make sure the FM antenna is positioned to achieve
the best possible reception.
Use the TUNING [e]/[r] buttons to tune
1
2
into a station.
Each time you press a TUNING button, the
frequency changes 0.05 MHz steps for FM.
If you press and hold a TUNING button, the
frequency will change continuously. Once you
release the button, tuning will stop automatically
when a frequency on which a radio station is
broadcasting is found. If you want to interrupt this
process, press the [CLEAR] button.
Press the [PRESET MEMORY] button.
“Auto Preset?” appears on the display.
2
To start the Auto Preset function, press
[ENTER].
Up to 30 stations can be preset and presets are
stored in frequency order.
If you want to interrupt the Auto Preset process,
press the [CLEAR] button.
3
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, press the
[MODE] button to switch to Mono mode and listen to
the station in mono.
Note:
• Depending on your location, a preset may be stored
with no station, and you’ll hear only noise when you
select it. In this case, delete the preset (see page 24).
23
Presetting FM Stations Manually
Receiving RDS
With the Preset Write function, you can manually preset
individual FM radio stations. Presets make it easy to
select your favorite stations and eliminate the need to
tune the radio manually each time you want to change
stations.
Press the [DISPLAY] button repeatedly to
display the following RDS information.
FM stations can also be preset automatically (see
Frequency and preset number
Program Service Name
Radio Text (if available)
About Presets
You can store up to 30 FM stations as presets.
Tune into the station that you want to store
1
Press and hold down the [PRESET
MEMORY] button to the preset number
flashes.
2
RDS can be viewed on this unit only in areas where RDS
broadcasts are available.
When the preset has been stored, the preset number
will change from blinking to steadily lit.
Preset numbers are automatically stored starting
with the lowest unused number.
If all 30 presets have been set, the display will
indicate “Preset FULL,” and no further presets can
be stored. You’ll need to erase an existing preset
before storing another one.
What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
within the European Broadcasting Union (EBU) and
many European FM radio stations use it these days.
The unit supports and displays Program Service Name
(PS) and Radio Text (RT) RDS data.
The RDS indicator appears on the display when the unit
is tuned to an FM station that supports RDS.
Selecting Preset Stations
Note:
You must store some presets before you can select them
(see pages 23 to 24).
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
• The message “Waiting” may appear while the RT data
is being received.
Press the [TUNER] button to select “FM”.
Alternatively, you can use the CD receiver’s
[INPUT] button.
1
The preset you selected the last time you listened to
the radio will be selected.
Erasing Presets
Select the preset you want to erase.
1
Use the PRESET [e]/[r] buttons to select a
2
preset.
Press and hold down the [CLEAR] button to
erase the preset.
When the preset has been erased, presets following
the erased preset will be renumbered forward and
redisplayed.
2
Press the PRESET [e] button to select the
previous preset. Press the PRESET [r] button to
select the next preset.
Tip:
• If you press the remote controller’s [TUNER] button
while the CD receiver is on Standby, it will turn on
automatically and the station that you listened to last
time will be heard.
24
Playing a USB Flash
Drive
Setting the Clock
This section describes the procedure for using the
remote controller, unless otherwise specified.
This section describes the procedure for using the
remote controller, unless otherwise specified.
Setting the Clock
Press the [iPod] button to select “iPod”.
Alternatively, you can use the CD receiver’s
[INPUT] button.
1
Press the [TIMER] button repeatedly until
“Clock” appears.
1
Press [ENTER].
Press and hold the [MODE] button until
“USB” appears (about 3 seconds).
2
2
Use the arrow [q]/[w] buttons to enter the
3
current hour.
Insert a USB flash drive in the USB port.
3
When the CD receiver is shipped from the factory,
the time display format is set to 24-hour time. Set
the current hour as it would appear in 24-hour time.
If you want to set the current hour as 12-hour time,
press the [DISPLAY] button.
Press [ENTER].
4
Use the arrow [q]/[w] buttons to enter the
5
current minute.
USB flash drive
Press [ENTER].
6
The clock is set and the second dot starts flashing.
To start playback, press the [1/3] button.
4
Displaying the Time
Selecting folders and files, and using the random
play and repeat play functions, are the same as
when playing back MP3 files from a CD (see
To display the time, press the remote controller’s
[CLOCK CALL] button. Press the button again or
perform another operation to cancel the time display.
If the CD receiver is on Standby, the time will be
displayed for about 8 seconds.
Note:
• Do not connect your USB flash drive via a USB hub.
• When connecting or disconnecting a USB flash drive,
use your hand to support the CD receiver so that it
does not move.
While the CD receiver is on, the time are displayed
continuously.
Change the time format
To change the time format between 12-hour and 24-hour,
press the [DISPLAY] button.
• For details on the usable formats for a USB flash
• If your iPod/iPhone/iPad is used, switch the
connection mode to iPod (see page 21).
• Do not connect the CD receiver’s USB port to a USB
port on your computer. Music on your computer
cannot be played through the CD receiver in this way.
25
Using the Timer
This section describes the procedure for using the
remote controller, unless otherwise specified.
Use the arrow [q]/[w] buttons to select the
source, and then press [ENTER].
You can select the following sources:
FM, CD, iPod (USB), LINE.
In the display, “TIMER” and a number indication
will blink according to the input source you’ve
selected.
3
The CD receiver has a programmable timer for
automated playback, and a sleep timer for turning the
CD receiver off after a specified period.
You can also use the alarm playback function of your
iPod to initiate timer playback on the CD receiver.
The number will be “1” for FM, “2” for CD, “3”
for iPod (USB), and “4” for LINE.
The timer can be used to start FM, CD, iPod/USB, or
LINE playback at a specified time. You could, for
example, use a timer to turn on the CD receiver every
morning, just like a radio alarm clock.
Use the arrow [q]/[w] buttons to specify the
hour at which you want the timer to play,
and then press [ENTER].
4
5
6
Note:
• If iPod is selected as the input source for the timer
settings, USB will play if only a USB flash drive is
connected, and iPod/iPhone/iPad will play if an iPod/
iPhone/iPad is connected.
Use the arrow [q]/[w] buttons to specify the
minute at which you want to timer to play,
and then press [ENTER].
Programming the Timer
Use the arrow [q]/[w] buttons to select
“Timer On,” and then press the [ENTER]
button.
Note:
• You must set the clock before you can program the
timer.
When a timer is turned on, its “TIMER” and
number appears on the display.
• If you don’t operate any buttons for about 5 seconds
while programming a timer, the procedure will be
cancelled and the previous display will reappear.
• When the CD receiver is turned on by the timer,
playback will begin with the most recently received
station in the case of FM, the first song in the case of
a CD or iPod (USB), and the current state of the
connected device in the case of LINE.
• Only one timer can be set.
If there is no operation for several seconds, the
setting will be made with the currently-shown
content.
The display will return to its previous state except
for “TIMER” and the number of the selected input
source; the timer is now set.
Press the On/Standby [8] button to set the
7
CD receiver to Standby.
Prepare the source that you want the timer
to play.
If you want FM to play, tune to the station you
1
Tip:
• If you decide to cancel during this procedure without
making timer settings, press the [TIMER] button.
• By pressing the [DISPLAY] button when specifying
the time, you can switch between 12-hour and 24-hour
displays.
want to hear.
If you want a CD to play, insert the disc.
If your iPod/iPhone/iPad is used, switch the
USB flash drive is used, switch the connection
mode to USB (see page 25).
If you want to play a device connected to LINE,
make settings on the connected device so that it
will start playing when the timer operates.
Note:
• Be sure to set the CD receiver to Standby, otherwise
the timed operation will not work.
If the timer has been set, timed operation will work
even if the SLEEP timer caused the CD receiver to
enter Standby mode.
Once the timer has been turned on, playback will start
at the same time every day. Be sure to turn off the
timer before leaving on vacation.
• If the timer turns the power on, the “SLEEP”
indication will light. If no operation is performed for
one hour, the CD receiver will automatically enter
Standby mode. If you perform any operation, the
“SLEEP” indication will turn off, and the CD receiver
will continue operating.
Press the [TIMER] button repeatedly until
“Timer XX” appears.
“XX” indicates the source that was last selected for
2
timer playback.
26
Note:
Turning Timer On and Off
• If the timer turns the power on, the “SLEEP”
indication will light. If you perform any operation, the
“SLEEP” indication will turn off. If you want to set
the SLEEP timer, you’ll need to make the setting again
after the “SLEEP” indication turns off.
Once a timer has been programmed, you can turn it on or
off as necessary. For example, while you’re on holiday,
you may want to turn off the timer you use as an early
morning alarm.
Press the [TIMER] button repeatedly until
“Timer On” or “Timer Off” appears.
Timer Playback using the Alarm Play
Function of your iPod
1
When the alarm play function of the iPod connected to
the CD receiver starts playing a song, the CD receiver
will power-on and switch to the iPod input.
Use the arrow [q]/[w] buttons to select
If there is no operation for several seconds, the
setting will be made with the currently-shown
content, and the display will return to its previous
state.
2
either “Timer On” (set) or “Timer Off”
(cancel), and then press the [ENTER]
button.
On your iPod, make settings for its alarm
play function.
1
Repeatedly press the [TIMER] button to
make the iPod alarm mode “iPodAlarmOff”
message appear.
2
If you specify Timer On (set), the “TIMER”
indication and the number of the selected input
source will light.
If you select Timer Off (i.e., turn off the timer), the
“TIMER” indicator will disappear.
Use the arrow [q]/[w] buttons to select
3
“iPodAlarmOn”, and then press the
[ENTER] button.
If there is no operation for several seconds, the
setting will be made with the currently-shown
content, and the display will return to its previous
state.
Using the Sleep Timer
With the sleep timer, you can set the CD receiver so that
it automatically turns off after a specified period.
Press the On/Standby [8] button to set the
4
Press the [SLEEP] button repeatedly to select
the required sleep time.
CD receiver to Standby.
When the alarm play function of the iPod begins,
the CD receiver will power-on and the input will be
switched to iPod.
With the [SLEEP] button, you can set the sleep time
from 90 to 10 minutes in 10 minute steps.
When the sleep timer has been set, the SLEEP indicator
appears on the display. The sleep time appears on the
display for about 3 seconds, then the previous display
reappears.
Note:
• In order for the timer to work, the CD receiver must be
in standby mode.
• This function will not work if the iPod is not
connected.
• This function won’t work when the sound set for the
alarm is a built-in sound (Beep).
• This function won’t work with models on which
music files cannot be used to set the alarm sound.
Checking the Remaining Sleep Time
To check the remaining sleep time, press the [SLEEP]
button.
Note that if you press the [SLEEP] button while the sleep
time is being displayed, you’ll shorten the sleep time by
10 minutes.
Tip:
For example if you press the [SLEEP] button and the
remaining time is shown as 55 minutes, pressing the
[SLEEP] button once again will shorten this time to 50,
and each subsequent press will shorten the time in 10
minute increments.
• This function will power-on the CD receiver and
switch the input to iPod when it detects a song being
played back by the iPod. If you play back a song on the
iPod without using its alarm play function, the CD
receiver will power-on and switch to the iPod input in
the same way.
Canceling the Sleep Timer
To cancel the sleep timer, press the [SLEEP] button
repeatedly until “Sleep Off” appears.
27
Troubleshooting
If you have any trouble using the CD receiver, look for a solution in this section.
If you can’t resolve the issue yourself, try resetting the CD receiver before
contacting your Onkyo dealer.
To reset the receiver to its factory defaults, turn it on and, while holding down
the CD receiver’s Previous [7] button, press the [8 ON/STANDBY] button.
When the display indicates “RESET”, release the buttons. After a while, the
CD receiver will enter standby mode.
Note that resetting the CD receiver will delete your radio presets and custom settings.
Power
Can’t turn on the CD receiver.
• Unplug the power cord from the wall outlet, wait 30 minutes or more, then plug it in again.
The CD receiver turns off unexpectedly.
• If the sleep timer has been set and the SLEEP indicator is shown on the display, the CD receiver will turn off
• The CD receiver will automatically enter standby mode when Auto Standby has been set and launches (see page 16).
Audio
There’s no sound.
• If there’s no sound from an external device connected to LINE IN, check whether the external device’s audio output
level (volume) might be too low.
The sound quality is not good.
• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices
away from the CD receiver.
• If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone that’s being
used to make a call, the CD receiver may output noise.
• The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during playback or
when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
Headphones output is intermittent or there’s no sound.
• This may be due to dirty contacts. Clean the headphones plug. See your headphones’ instruction manual for cleaning
information. Also, make sure that the headphones cable is not broken or damaged.
28
Audio performance.
• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time
to warm up.
• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.
CD Playback
The disc will not play.
• Make sure the disc has been loaded correctly, with the label-side facing up.
• If condensation is suspected, turn on the CD receiver and leave it for 2 to 3 hours before playing any discs.
It takes a long time for playback to start.
• It may take the CD receiver a while to read CDs that contain many tracks or files.
Playback jumps.
Can’t play MP3 Discs.
• The disc has not been finalized. Finalize the disc.
• MP3 files without a “.MP3” or “.mp3” filename extension are not recognized.
iPod/iPhone/iPad
There’s no sound.
• Check if “iPod” appears on the display of the CD receiver. If “USB” appears, switch the connection mode to iPod
• Make sure the CD receiver is turned on, the input source is set to iPod, and the volume is not set too low.
The message “ERROR” is displayed.
• Try reconnecting your iPod/iPhone/iPad.
Can’t control your iPod/iPhone/iPad with the CD receiver’s remote controller.
• Your iPod/iPhone/iPad may not work soon after it is connected to the CD receiver with a USB cable. In this case, wait
a few moments until your iPod/iPhone/iPad wakes up.
• Depending on your iPod/iPhone/iPad model, its software version, or the content you’re playing, some functions may
• The iPod/iPhone/iPad might not be connected if its power is turned off, or if it is insufficiently charged. Check the
state of your iPod/iPhone/iPad.
The message “No Device” is displayed.
• Try reconnecting your iPod/iPhone/iPad.
Can’t recharge the iPod/iPhone/iPad.
• Check if “iPod” appears on the display of the CD receiver. If “USB” appears, switch the connection mode to iPod
• Check the iPod/iPhone/iPad connection.
• Depending on the state of your iPod/iPhone/iPad, the CD receiver might not be able to charge it. Try using the
dedicated charging method provided for the iPod/iPhone/iPad.
29
Bluetooth
Bluetooth connection cannot be built.
• When building a Bluetooth connection between the CD receiver and your device for the first time, if the connection
is fail, you need to power off your device and power on again to clear the device name, and build the connection again
USB Flash Drive Playback
Can’t access the music files on a USB flash drive.
• Check if “USB” appears on the display of the CD receiver. If “iPod” appears, switch the connection mode to USB
• The CD receiver supports USB flash drives only. Note, however, that playback may not be possible with some USB
flash drives.
• Make sure that the USB flash drive has been formatted as FAT16 or FAT32.
• USB flash drives with built-in USB hub functionality are not supported.
• This CD receiver cannot play files other than MP3 files.
The message “No Device” is displayed.
• Try reconnecting your USB flash drive.
Can’t play MP3 files.
• MP3 files without a .MP3 or .mp3 filename extension are not recognized.
• The MP3 file’s copyright option is on. Don’t use the copyright option.
Tuner
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all stations, or
the FM ST indicator doesn’t light up when tuned to a stereo FM station.
• Move the CD receiver away from a nearby TV or computer.
• Cars or airplanes can cause noisy interference.
• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
If a power failure occurs or the power cable is disconnected.
• A brief power outage will not cause the contents of memory to be lost. However if the power cable is left disconnected
for an extended period of time, only the clock settings (including the timer) will be reset. Please make these settings
Can’t adjust the frequency of the radio.
• Use the remote controller’s TUNING [e]/[r] buttons to change the frequency of the radio (see page 23).
RDS doesn’t work.
• The FM station you are tuned to doesn’t support RDS.
• The radio signal is weak. Change the position of the antenna. If that doesn’t work, install an outdoor FM antenna (see
Remote Controller
The remote controller doesn’t work properly.
• Replace the battery with a new one.
• The remote controller is too far away from the CD receiver, or there’s an obstacle between them (see page 6).
• The CD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
• The CD receiver is located behind the tinted glass doors of an audio rack or cabinet.
30
External Components
No sound is heard from your turntable.
• Make sure the turntable has a built-in phono equalizer. If the turntable doesn’t have a phono equalizer built-in, you
must provide one.
Timer
The timer doesn’t work.
• Timed operation will fail if the CD receiver is on at the specified On time, so make sure it’s set to Standby (see
• If you press the [TIMER] button while a timed operation is in progress, the timer will be cancelled.
• The volume setting for timer playback will be the volume that was set before the CD receiver entered standby mode.
Set the appropriate volume beforehand.
• If a power failure occurs and the clock stops, the timer will also be reset. Reset the clock, and then make timer settings.
Clock
The display indicates “- - : - -” when you press the [CLOCK CALL] button.
Others
Standby power consumption.
• Charging will begin when you connect an iPod/iPhone/iPad, causing the power consumption to increase. Charging
will occur even if the CD receiver enters standby mode.
Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure that the material will be recorded correctly.
The CD receiver contains a microcomputer. In very rare situations, severe interference, noise from an external source,
or static electricity may cause it to malfunction or lock up. In the unlikely event that this should happen, unplug the
power cord, wait at least 30 minutes, and then plug it back in again. If this doesn’t resolve the issue, reset the CD
receiver to its factory defaults (see page 28).
31
Specifications
Amplifier
General
Rated output power (IEC) 2ch
×
15 W (6 Ω, 1 kHz, 2ch driven)
Power supply
AC 220 - 240 V, 50/60 Hz
30 W
THD + N (total harmonic distortion + N )
Power consumption
10% (Power Rated)
0.5% (1 kHz 1W)
No-sound power consumption 7.9 W
(when not charging iPod/iPhone)
Damping factor
60 (1 kHz, 8 Ω)
Standby power consumption 0.5 W
(when not charging iPod/iPhone)
Input sensitivity and impedance
1000 mV/47 kΩ (LINE)
Frequency response
Tone control
Dimensions (W × H × D)
215 × 100 × 270 mm
(8-1/2" × 3-15/16" × 10-5/8")
40 Hz - 20 kHz/+0 dB, –3 dB
Weight
2.4 kg (5.3 lbs.)
+10 dB, –10 dB, 100 Hz (BASS)
+10 dB, –10 dB, 10 kHz (TREBLE)
+4 dB/+8 dB, 80 Hz (S.BASS 1/2)
■ Audio input
Analog input
LINE
Signal to noise ratio
Speaker impedance
84 dB (LINE, IHF-A)
6 - 16 Ω
■ Audio output
Analog output
HEADPHONES, SPEAKERS,
SUBWOOFER
Tuner
■ Other
USB
Tuning frequency range
Channel presets
87.50 MHz - 108.00 MHz
30
2.0 HS
CD
Playable media
CD and CD-R/CD-RW (music CDs
and MP3 CDs)
Specifications and features are subject to change without
notice.
USB
Playable media
USB Flash Drive (MP3)
Bluetooth
Version
Profile
Codec
2.1 + EDR
A2DP 1.2
SBC, AAC, aptX
Speakers D-T05
Type
2 way bass-reflex
6 Ω
Impedance
Maximum input power
Output sound pressure level
Frequency response
Crossover frequency
Cabinet capacity
30 W
82 dB/W/m
55 Hz - 50 kHz
4.5 kHz
3.4 liter (0.12 cubic feet)
Dimensions (W × H × D)
130 × 210 × 172 mm
(5-1/8" × 8-1/4" × 6-3/4")
(incl. grille and projection)
Weight
1.6 kg (3.5 lbs.)
Driver units
10 cm (3-15/16") Cone Woofer
2 cm (3/4") Balanced Dome
Tweeter
Terminal
Other
Spring Type Color Coded
Magnetic shielding
32
Memo
33
Memo
34
Memo
35
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
Y1208-2
SN 29401308A
(C) Copyright 2012 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 3 0 8 A *
|