Contents
DVD Receiver
DR-645
Instruction Manual
Thank you for purchasing an Onkyo DVD Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new DVD Receiver.
Please retain this manual for future reference.
En
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
9. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all around
this unit, especially if it’s installed in an audio rack.
If the ventilation is inadequate, the unit may
overheat, leading to malfunction.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners,
alcohol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
4. Power
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may rise,
shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject to
vibrations from loudspeakers. Never put the unit on
top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its side
or on a sloping surface, because it may cause a
malfunction.
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 200-240 V, 50/60 Hz or AC 120 V, 60 Hz).
• If you install this unit near a TV, radio, or VCR, the
picture and sound quality may be affected. If this
occurs, move this unit away from the TV, radio, or
VCR.
10. To Obtain a Clear Picture—This unit is a hightech,
precision device. If the lens on the optical pickup, or
the disc drive mechanism becomes dirty or worn, the
picture quality may be affected. To maintain the best
picture quality, we recommend regular inspection and
maintenance (cleaning or worn part replacement)
every 1,000 hours of use depending on the operating
environment. Contact your Onkyo dealer for details.
11. Moisture Condensation
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
Pressing ON/STANDBY to select Standby mode does
not fully shutdown the unit. If you do not intend to use
the unit for an extended period, remove the power cord
from the AC outlet.
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
8. Handling Notes
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility of
moisture condensation occurring. Doing so may
damage your discs and certain parts inside this unit.
If condensation does occur, unplug the power cord and
leave the unit for two to three hours in the room
temperature.
• If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
• Do not leave rubber or plastic items on this unit for
a long time, because they may leave marks on the
case.
• This unit’s top and rear panels may get warm after
prolonged use. This is normal.
• If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
12. Region Numbers—The DVD standard uses region
numbers to control how discs can be played around
the world, the world being divided into six regions.
This unit will only play DVD discs that match its
region number, which can be found on its rear panel
ALL
1
(e.g.,
,
).
13. About this Manual—This manual explains how to
use all of this unit’s functions. Although the DVD
standard offers many special features, not all discs use
them all, so depending on the disc being played, this
unit may not respond to certain functions. See the
disc’s sleeve notes for supported features.
• When you’ve finished using this unit, remove all
discs and turn off the power.
En
3
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to use
this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
CAUTION:
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME NMB-
003 DU CANADA.
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
The label on the right is applied
on the rear panel.
1. This unit is a CLASS 1
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified
personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
For U.S. models
Blue: Neutral
FCC Information for User
Brown: Live
CAUTION:
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
The user changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved
by ASTA or BSI to BS1362 and have the same ampere
rating as that indicated on the plug. Check for the ASTA
mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
En
4
Standard Accessories
*
FM antenna × 1
Using Remote Control
RCA video cable × 1
AC power cord × 1
Installing the Batteries
Batteries (AAA, R03, UM-4) × 2
Remote control (RC-798S) × 1
Instruction manual (this document) × 1
Note
• In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
Batteries
Note
• If the remote control doesn’t work reliably, try replacing the
batteries.
• Don’t mix new and old batteries or different types of batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent damage
from leakage or corrosion.
Aiming the Remote Control
To use the remote control, point it at the DVD receiver’s
remote control sensor, as shown below.
Remote control sensor
DVD receiver
Approx. 16 ft. (5 m)
En
5
Features
Highlights
*3
*4
• Compact-Size Home Entertainment DVD Systems for
iPod
• iPod Direct Connection via Top Panel
• Front Panel USB Interface for Flash Drives
“HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.”
Amplifier / DVD Player / USB Features
(North American)
• 20 W/Ch, 8 ohms, 20 kHz, 2Ch Driven (FTC)
(Others)
“DivX®, DivX Certified® and associated logos are registered
trademarks of DivX, Inc. and are used under license.”
*5
• 40 W/Ch, 4 ohms, 1 kHz, 1Ch Driven (IEC)
• Digital Amplifier Circuitry to Maintain Clean Audio
Signals
*3
• 1080p Video Upscaling via HDMI Output
iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
“Made for iPod” means that an electronic accessory has been
designed to connect specifically to iPod and has been certified
by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
• Front-Panel Audio Input for Portable Devices
• 1 Audio Input and 1 Output
• 1 Component Video Output
• 1 Digital Output (Coaxial)
• 1 Video Output
• 1 Subwoofer Pre Out
• Tone Control (Bass/Treble)
• Super Bass Function
*6
*1
• Plays DVD-Video , Video CD, Audio CD, CD-R and
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and
worldwide patents issued & pending.
DTS and the Symbol are registered trademarks, & DTS 2.0+
Digital Out and the DTS logos are trademarks of DTS, Inc.
Product includes software. © DTS, Inc. All Rights Reserved.
CD-RW, DVD-R and DVD-RW
• MP3, WMA, JPEG
• DivX (excluding North American models)
• CD 4 Play Modes (Normal/Memory/Random/Folder)
• Memory Playback
*4
• 3 Repeat Modes (Track/Full/Folders (for MP3 and
WMA formats))
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Tuner & Other Features
This product is protected by certain intellectual property
rights of Microsoft.
• Preset Function with 20 FM Selections
• Wake-up Timer
• Aluminum Front Panel and Volume Knob
Use or distribution of such technology outside of this
product is prohibited without a license from Microsoft.
Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United States
and/or other countries.
iPod Dock Features
*5
• Recharges iPod
It is forbidden by law to copy, broadcast, show, broadcast
on cable, play in public, and rent copyrighted material
without permission.
• Composite video output or component video output is
possible only with iPod that support video output.
DVD videos are copy protected, and any recordings made
from these discs will be distorted.
This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property
rights of Rovi Corporation.
*1
Reverse engineering and disassembly are prohibited.
is a trademark of DVD Format/Logo Licensing
Corporation.
*2
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories.
En
6
Contents
RDS (Display Setting of the FM)
Basic Operations for iPod, Disc
– excluding North American models.......................... 23
– excluding North American models.......................... 24
En
7
Connections
Connecting the DVD receiver
FM Antenna Connection
Speaker Connection
Connect the supplied FM antenna to the FM ANTENNA
socket on the unit.
If reception is poor, connect the outdoor antenna.
Subwoofer
Caution
Note
• Before attaching a 75 ohm coaxial cable, disconnect the supplied
FM antenna.
• To avoid damaging the speakers with a sudden high-level
signal, be sure to switch the power off before connecting
the speakers.
Before connection
Check the impedance of your speakers. Connect speaker
with an impedance of 4 Ω ~ 16 Ω.
The black speaker terminals are “-” (negative).
Generally, the “+” side of the speaker cable is marked to
make it distinguishable from the “-” side of the cable.
Connect this marked side to the “+” terminal and the
unmarked side to the black “-” terminal.
How to connect
Caution
Turn the terminal cap counterclockwise to loosen
it. The speaker terminal caps cannot be fully re
moved from the base.
• To avoid noise, keep antennas away from the system, the
connecting cord and the AC power cord.
1
Insert the wire into the terminal fully and turn the
terminal cap clockwise to securely connect it:
2
Subwoofer
Connect a subwoofer using a commercially-available
RCA cable. Use a subwoofer with built-in amplifier
referred to as a “powered subwoofer”.
En
8
A HDMI video/audio output jack
Connection to a TV
Use an HDMI cable to connect the unit to an HDMI
compatible television or monitor.
Caution
• Turn the power off to all components before making
connections.
• Read the instructions of each component you intend to
use with this unit.
• Be sure to insert each plug securely. To prevent hum and
noise, avoid bundling the signal interconnection cables
together with the AC power cord or speaker cables.
• If the television or monitor is equipped only with a DVI
terminal, a suitable adapter cable or adapters should be
used. Note that the television connected in this way must
be HDCP compatible. Also note that this connection
outputs no sound.
• Make sure that you read and understand the
documentation provided with the HDMI component.
■ HDMI video output formats
• 480p (60Hz)
B
C
A
• 576p (50Hz)
• 720p (50Hz) or 720p (60Hz)
• 1080i (50Hz) or 1080i (60Hz)
• 1080p (50Hz) or 1080p (60Hz)
■ To output audio from the HDMI jack
If the connected HDMI component is capable of inputting
HDMI audio, digital audio can be output from the HDMI
jack.
• Only PCM digital audio can be output from the HDMI
jack.
B Component video output jacks
Use component video cables to connect the unit to the
component video inputs of a suitably equipped television
or monitor to enjoy a high-quality picture. Use these
terminals in preference to composite video connections.
• If the component video terminals are connected to a
television with progressive scan capabilities, the output
can be set to match this.
• Note that these jacks cannot be connected to high
definition component jacks.
C Composite video output jack
Use a RCA (pin) video cable to connect the unit to the
composite video connector of a television or monitor.
Use this connection only if no other video connection
method is available.
TV (Monitor)
• Adjust the video aspect ratio to match that of the
television.
• This unit adopts analog copy protection features. If the
unit is connected to a TV through a VCR (video cassette
recorder), the resulting playback may be affected.
Connect the unit directly to the television.
• In all cases, use the highest quality cables for the best
possible picture.
• Select proper setting in the “VIDEO SETUP”.
En
9
D Digital audio output jack
Connection to Audio Components etc.
Digital audio from DVD-Video, CD and Video CD is
output from this jack. Connect an amplifiers including a
decoder, or digital audio components such as CD recorder,
etc. to this jack using commercially-available coaxial
digital audio cable.
Caution
• Turn the power off to all components before making
connections.
• Read the instructions of each component you intend to
use with this unit.
• Be sure to insert each plug securely. To prevent hum and
noise, avoid bundling the signal interconnection cables
together with the AC power cord or speaker cables.
• Select “ALL” or “PCM only” in the “DIGITAL
AUDIO SETUP”.
E LINE 1 IN/LINE OUT jacks
Analog 2-channel audio signal is input or output from
these jacks. Connect a cassette tape deck etc. to these
jacks using commercially-available RCA cables.
Make sure to connect:
F E
D
• white plug: white jack (L: left channel)
• red plug: red jack (R: right channel)
F Power cord receptacle
After all other connections have been made, insert the
supplied AC power cord into this receptacle, then connect
the other end of the power cord into the wall socket.
• In order to avoid the risk of electric shock, fire, and so
on, only use the supplied power cord.
• If you are not going to use the unit for some time,
disconnect the power cord from the wall socket.
Cassette tape
deck, etc.
Digital audio component
(CD recorder,
MD deck, etc.)
To AC wall outlet
En
10
Identifying the Parts
a Remote control sensor
Main Unit
Receives signals from the remote control. Point the
remote control at this sensor when operating the
remote control.
a
b
c
d
b Display
c Disc tray
d VOLUME knob
Turn this knob (or press q VOL w of the remote
control) to adjust the volume level.
e 9 ON/STANDBY button/STANDBY indicator
Use this button to turn the unit on and standby. The
STANDBY indicator lights in the standby mode. It
turns off when the unit is turned on.
e
f gh i
j k l m n
The equipment draws nominal non-operating
power from the AC outlet with its
■ Top view
9 ON/STANDBY in the standby mode.
f INPUT button
Use this button to select an input source as follows:
DVD, iPod, USB, FM, LINE1 or LINE2
g
(headphones) jack
For private listening, insert the headphones plug into
this jack, and adjust the volume using the VOLUME
knob.
h LINE 2 IN jack
You can connect a portable audio player to this jack.
o
i USB port
You can connect a USB flash drive to this port.
j 7 button
In DVD, iPod or USB mode, use 7 to skip
tracks/files/songs.
e PRESET button
In FM mode, use e PRESET to select a preset
channel.
k 6 button
In DVD, iPod or USB mode, use 6 to skip
tracks/files/songs.
PRESET r button
In FM mode, use PRESET r to select a preset
channel.
l 2 button
In DVD or USB mode, use this button to stop
playback.
In iPod mode, use this button to pause playback.
In FM mode, use this button to select Auto mode or
Mono mode.
m 1/3 button
In DVD, iPod or USB mode, use this button to start or
pause playback.
n 0 button
Use this button to open and close the disc tray.
o iPod dock connector
Connects to your iPod.
En
11
a 9 ON/STANDBY button
Remote Control
Use this button to turn the unit on and standby.
The STANDBY indicator lights in the standby mode.
It turns off when the unit is turned on.
b iPod/USB button
Use this button to select an “iPod” or “USB Source”.
a
b
c
d
e
f
g
s
u
w
y
t
v
x
c DVD button
Use this button to select a “DVD Source”.
d SUBTITLE button
Use this button to select the displayed subtitles during
DVD playback.
e AUDIO button
h
i
z
B
Use this button to select the audio for playback.
A
f ZOOM button
In DVD or USB mode, use this button to enlarge the
image.
j
g DIMMER button
k
l
In standby mode, use this button to change the
brightness of the front panel display.
C
E
h TITLE button
D
m
During PBC playback, use this button to display a
menu.
n
o
p
i q button
F
H
Use q for navigation of on-screen menus.
G
I
ANGLE button
Use ANGLE to select camera angles during DVD
q
playback.
j e button
r
Use e for navigation of on-screen menus.
k w button
Use w for navigation of on-screen menus.
J
SLOW button
In DVD mode, use SLOW for slow motion video
playback.
l SETUP button
Use this button to enter the SETUP menu where you
can setup the parameters of the unit.
m 4 button
In DVD, iPod or USB mode, use 4 to search for a
part of a track/file/song.
TUNING q button
In FM mode, use TUNING q to tune in a station.
n 5 button
In DVD, iPod or USB mode, use 5 to search for a
part of a track/file/song.
TUNING w button
In FM mode, use TUNING w to tune in a station.
o 1/3 button
In DVD, iPod or USB mode, use this button to start or
pause playback.
En
12
p 7 button
E VOL w (Volume Down) button
In DVD, iPod or USB mode, use 7 to skip
tracks/files/songs.
Use this button to adjust the volume level.
F 2 button
e PRESET button
In DVD or USB mode, use 2 to stop playback.
In FM mode, use e PRESET to select a preset
In iPod mode, use 2 to pause playback.
channel.
FM MODE button
In FM mode, use FM MODE to select auto or
monaural.
q PROG button
In DVD or USB mode, use PROG to programme
tracks.
G 6 button
MEMORY button
In FM mode, use MEMORY to preset stations.
In DVD, iPod or USB mode, use 6 to skip
tracks/files/songs.
r Number buttons
PRESET r button
Use these buttons to enter track numbers, passwords,
etc.
In FM mode, use PRESET r to select a preset
channel.
s SLEEP button
H REPEAT button
When the unit is on, use SLEEP to set the sleep timer.
In DVD, iPod or USB mode, use this button for repeat
playback.
TIMER button
In the standby mode, use TIMER to set the wake up
I A-B button
timer.
In DVD or USB mode, use this button to specify a
section and play it repeatedly.
t FM button
Use this button to select a “FM Radio”.
J SEARCH button
Use this button to start time search.
In FM mode, use this button to preset stations
automatically.
u LINE button
Use this button to select a “LINE1 Source” or
“LINE2 Source”.
v CLOCK button
In standby mode, use this button to adjust clock.
w TONE button
Use this button to adjust bass and treble together with
q VOL w.
x DISPLAY button
In DVD or USB mode, use this button to display
information about the currently playing disc.
In FM mode, use this button to change the information
on the second line of the display. (This function only
works in areas where RDS broadcasts are available.)
y S.BASS button
Use this button to boost low end bass.
z MENU button
In DVD mode, use this button with menu-enabled
DVD discs to bring up the DVD menu.
In iPod mode, use this button to go back to previous
menu of iPod.
During playback of MP3/WMA/JPEG files, use this
button to switch between the folder list and the file
list.
When a VCD (version 2.0) is loaded, use this button to
turn the PBC function on or off.
A ENTER button
Use this button to confirm menus selections.
B r button
Use r for navigation of on-screen menus.
C MUTING button
Use this button to mute the sound.
D VOL q (Volume Up) button
Use this button to adjust the volume level.
En
13
Discs
■ About DVD-RW
Type of discs that can be played on this unit
• DVD-RW discs that were recorded with copy-once only
permission cannot be played.
• When playing a DVD-RW disc that was edited on a
DVD recorder, the screen may momentarily black out at
the edited point.
• When playing a DVD-RW disc that was edited on a
DVD recorder, you may see scenes from just before the
edited point.
This unit can playback discs bearing any of the following
logos:
This unit does not support disc types not listed.
DVD Video
• Single-sided or double-sided discs
• Single layer or dual layer discs
• Dolby Digital, MPEG or Linear PCM
digital audio
■ About CD-R/CD-RW
CD-R/CD-RW discs recorded in Audio CD format and
finalized correctly are playable. But depending on the
quality of the disc and/or the condition of the recording,
some CD-R/CD-RW discs may not be playable.
• MPEG-2 digital video
• This unit can play DVD-R discs recorded in
DVD video format.
• This unit can play DVD-RW discs recorded
in DVD video format or DVD video
recording format.
Discs are generally divided into one or more
titles.
Caution
• If you record a disc using a personal computer, even if it
is recorded in a compatible format, there are cases in
which it may not play because of the settings of the
application software used to create the disc. (Check with
the software publisher for more detailed information.)
• Unfinalized CD-R/CD-RW/DVD-R/DVD-RW discs
cannot be played.
Titles may be further subdivided into
chapters.
Audio CD
• 12 cm or 8 cm discs
• Linear PCM digital audio
Audio CDs are divided into tracks.
Video CD
• 12 cm or 8 cm discs
• MPEG-1 digital audio
• MPEG-1 digital video
Video CDs are divided into tracks.
SVCD
Copy-protected discs, Dual Discs and other discs that do
not conform to the CD standard may not play back
correctly in this unit. If you use such discs in this unit,
Onkyo Corporation and its subsidiaries cannot be
responsible for any consequences or guarantee the quality
of reproduction. If you experience problems with such
non-standard discs, you should contact the producers of
the disc.
• 12 cm or 8 cm discs
• MPEG-1 Audio Layer 2
• MPEG-2 digital video
Playable file format
This unit can play following files recorded on a CD-R,
CD-RW, DVD-R, DVD-RW or USB flash drive:
• MP3 files
■ Region Number of DVD Video discs
DVD players and discs are designed with region numbers
that dictate the regions in which a disc can be played. If
the region number on the disc you want to play does not
match the region number of your DVD player, you will
not be able to play the disc. In that case, an error message
will appear on the screen.
• WMA (Windows Media-formatted audio) files
• JPEG files
®
®
®
®
• DivX video files (DivX 5, DivX 4, DivX 3 and
®
DivX VOD video content) (excluding North
American models)
Note
The region number is printed on the rear panel of this unit.
• File names should be alphanumeric characters. This unit
cannot display symbols and full-size or double-byte
characters (such as Japanese, Chinese, etc.) correctly.
Also, be sure to use the file extension. (“.mp3” for MP3
files, “.wma” for WMA files, “.avi” or “.divx” for
North American
®
DivX video files, “.jpg” or “.jpeg” for JPEG files.)
European
• Files are played in alphabetical order.
• MP3 files must be monaural or stereo MPEG-1 Audio
Layer 3 format. This unit can play MP3 files with
sampling frequency 44.1 kHz or 48 kHz, bit-rate
320 kbps or less.
Hong Kong
• This unit can play WMA files with sampling frequency
44.1 kHz, bit-rate 192 kbps or less.
En
14
• This unit cannot display the bit-rate of VBR (variable
bit-rate) files correctly.
Handling precautions
• Always place the disc on the disc tray with the label side
up. Compact discs can be played or recorded only on one
side.
• To remove a disc from its storage case, press down on
the center of the case and lift the disc out, holding it
carefully by the edges.
• The disc must be finalized in order to play.
• This unit is NOT compatible with multi-session discs.
• The CD-ROM must be ISO 9660 compatible.
• It may take time to display a progressive JPEG picture.
• Depending on the file size and compression rate, some
JPEG pictures cannot be displayed correctly.
• Some MP3 players etc. that can connect via the USB
terminal cannot be played back with this unit.
®
ABOUT DIVX VIDEO: DivX is a digital video
How to remove the disc
How to hold the disc
format created by DivX, Inc. This is an official DivX
Certified device that plays DivX video. Visit
www.divx.com for more information and software tools
to convert your files into DivX video.
Maintenance
• Should the disc become dirty, wipe the surface radially
(from the center hole outward towards the outer edge)
with a soft, dry cloth.
ABOUT DIVX VIDEO-ON-DEMAND: This
®
DivX Certified device must be registered in order to
play DivX Video-on-Demand (VOD) content. To
generate the registration code, locate the DivX VOD
section in the device setup menu. Go to vod.divx.com
with this code to complete the registration process and
learn more about DivX VOD.
• Never use such chemicals as record sprays, antistatic
sprays or fluid, benzine or thinner to clean the discs.
Such chemicals will do irreparable damage to the disc’s
plastic surface.
Example of Icons used on DVD discs
Storage precautions
Number of audio tracks recorded on the disc
Number of subtitles recorded on the disc
Screen aspect ratio
• Discs should be returned to their cases after use to avoid
dust and scratches that could cause the laser pickup to
“skip”.
Disc recorded with multiple camera angles
Region code
• Do not expose discs to direct sunlight or high humidity
and temperature for extended periods.
Long exposure to high temperatures will warp the disc.
• CD-R and CD-RW discs are more sensitive to the effects
of heat and ultraviolet rays than ordinary CDs. It is
important that they are not stored in a location where
direct sunlight will fall on them, and away from sources
of heat such as radiators or heat-generating electrical
devices.
If you are in any doubt as to the care and handling of a
disc, read the precautions supplied with the disc, or
contact the disc manufacturer.
Caution
• Do not play any disc that is warped, deformed or
damaged. Playing such discs may cause irreparable harm
to the playing mechanisms.
• Printable discs are not recommended, as the label side
might be sticky and damage the unit.
• Do not stick papers or protective sheets on the discs and
do not use any protective coating spray.
• Use a soft oil-based felt-tipped pen to write the
information on the label side. Never use a ball-point or
hard-tipped pen, as this may cause damage to the
recorded side.
• Never use a stabilizer. Using commercially available CD
stabilizers with this unit will damage the mechanisms
and cause them to malfunction.
• Do not use irregular shape discs (octagonal, heart
shaped, business card size, etc.). Discs of this sort can
damage the unit:
En
15
iPod
To play your iPod through this unit, you must first attach
the Universal Dock Adapter for your model of iPod.
Handling precautions
Prepare the adapter that came with your iPod.
Compatible iPod models
Made for:
• iPod touch (1st and 2nd generation)
• iPod classic
• iPod (5th generation)
• iPod nano (1st, 2nd, 3rd, 4th and 5th generation)
How to open the dock cover
Note
• Before using this unit, update your iPod with the latest software,
available from the Apple Web site.
Universal Dock Adapter
supplied with your iPod
Caution
• If you use a case with your iPod, always remove it before
you insert it. Otherwise, it may not connect properly and
a malfunction may occur.
• Do not insert your iPod into the dock connector without
the Universal Dock Adapter that came with it, as it may
put unnecessary strain on the iPod or unit’s dock
connector, causing permanent damage.
How to insert the iPod
• To prevent dock connector damage, don’t twist your
iPod when inserting or removing it, and be careful not to
knock your iPod while it’s inserted.
• Don’t use your iPod with any other accessories, such as
FM transmitters and microphones, because they may
cause a malfunction.
■ Attaching the Universal Dock Adapter
Fit the front edge of the adapter into the dock, and then
press in the back edge of the adapter onto the dock until
a slight “click” is heard indicating the adapter is
inserted correctly.
• Use the Universal Dock Adapter that supplied with the
iPod or a commercially available one to use the other
types of iPod.
• If the Universal Dock Adapter is not supplied, or if you
lose it, purchase a new Apple Universal Dock Adapter.
• When the iPod is inserted, input source is selected to
“iPod” and start playback from music list automatically.
• The iPod is charged when it is inserted into the dock and
the unit’s power consumption is increased.
• When the iPod is inserted, the video signal is output
from this unit with no video played back on the iPod
LCD screen.
■ Removing the Universal Dock Adapter
To remove the Universal Dock Adapter from this unit,
attach a small flathead screwdriver into the slot, and lift
it out, as shown below.
En
16
USB flash drive compatibility
• Only USB flash drive can be used.
• Some MP3 players etc. that can connect via the USB
port cannot be played back with this unit.
• Hard disk drives, CD/DVD drives, and others connected
via USB cannot be used.
• The unit cannot copy, move, or delete files.
• Playable format: FAT12, FAT16, FAT32
• NTFS, HFS, HFS+ cannot be used.
• Max. number of playable folders: 300
• Max. number of playable files: 650
• USB flash drive cannot be used by way of the USB hub.
En
17
Basic Operation
Basic Operation
Press 9 ON/STANDBY to turn the unit on.
• The unit turns on with the source that was last
selected.
1
2
Press DVD, iPod/USB, FM, or LINE to select a
source.
The selected source is shown on the front panel’s
display.
Press LINE repeatedly to switch between LINE 1
and LINE 2.
Also, each time INPUT on the unit is pressed, the
source changes as follows:
• DVD Source
• iPod
• USB Source
• FM Radio
• LINE1 Source
• LINE2 Source
Play the source, and adjust the volume using
q VOL w.
3
You can rotate the VOLUME knob on the unit to
reduce or bring up the volume continuously.
• Press 9 ON/STANDBY to put the unit in the
standby mode when it is not being used.
Setting the Clock
If the unit is on, press 9 ON/STANDBY to turn
1
it standby.
Press CLOCK to show the time on the display.
2
• The time appears on the display (if the time is not
set after it blackout, “--:--” blinks). Press CLOCK
again, the “hour” value starts blinking.
• When no button is pressed for 30 seconds, the time
setting mode will be cancelled.
Press q VOL w to set the current hour.
3
4
Press CLOCK.
The “minute” value starts blinking.
Press q VOL w to set the current minute.
5
6
Press CLOCK.
The clock starts.
En
18
Basic Operation
Listening to a Disc
Recording a Source
Press DVD to select “DVD Source”.
• When no disc is loaded in the disc tray, “NO
DISC” is displayed.
1
You can record a source onto a CD recorder or a cassette
tape recorder connected to the COAXIAL DIGITAL
AUDIO OUT jack or the LINE OUT jacks.
Press 0 on the unit to open the tray.
2
3
Select a source to be recorded by pressing DVD,
iPod/USB, FM, or LINE.
1
Place the disc on the disc tray (with the printed
side up).
Start recording.
2
Press 0 on the unit again to close the tray.
4
• When the recording device is connected to the
LINE 1 IN jack and the LINE OUT jack, you
cannot select the LINE 1 Source for the recording
source.
• Some discs may automatically start playback.
Press 1/3 to start playback if playback has not
5
started automatically.
If a menu is shown on screen (some DVD or video
discs may show such a menu), see “On-screen
Dimmer
Press DIMMER to dim the display.
Listening to an iPod
Press DIMMER again to cancel the dimmer
function.
Press iPod/USB once or twice to select “iPod”.
1
2
Push your iPod firmly onto the unit’s dock
connector.
Never insert the iPod into dock connector without
the Universal Dock Adapter.
Muting
To mute the sound temporarily, press MUTING.
Press MUTING again to restore the sound.
Press 1/3 to start playback.
3
• “MUTING” blinks on the display while muting is
engaged.
• If you change the volume when the sound is muted,
it will be unmuted.
■ Stand-by power consumption
When charging the iPod, the power consumption may
reach up to a maximum of 14 W.
Listening to a USB Flash Drive
Super Bass boost
You can reinforce the bass sound to maintain rich, full
bass at low volume.
Press iPod/USB once or twice to select “USB
Source”.
1
Press S.BASS to get the effect.
Plug your USB flash drive into the USB port.
2
It takes a few seconds for the unit to load the USB
flash drive. Some files may automatically start
playback.
Press S.BASS again to cancel the effect.
• You can reverse steps 1 and 2.
Adjusting the bass and treble
Press 1/3 to start playback if playback has not
3
You can change the bass and treble sound between “-5” to
“+5”.
started automatically.
Note
Press TONE repeatedly to select Bass or Treble.
1
2
• Do not unplug the USB flash drive before playback is stopped.
Press q VOL w to adjust the sound level.
En
19
MP3 and Windows Media-formatted audio
files
On-screen Menu
An on-screen menu is shown when a DVD, USB or Video
CD with Playback Control (PBC) content is loaded.
The way in which the menu works may differ according to
disc.
When a disc or USB is loaded, a list of directories appears
on the screen and the first file will automatically start
playback.
Select a directory by pressing q/w and press the
1
DVD menus
ENTER.
File names will appear on the screen.
Use q/w/e/r to select the menu item from a
Select a file by pressing q/w and press the ENTER.
2
DVD, and confirm the selection using the ENTER.
Playback will start from the selected file.
• Press MENU to switch between the folder list and
the file list.
Returning to the menu screen
Press either MENU or TITLE.
• If you want to return to the parent folder, display
the folder list using MENU, select “...” using
q/w/e/r and press ENTER.
• Depending on the disc, pressing MENU during playback
may restart playback from the first chapter.
• During playback, elapsed time of the current file is
displayed on the front panel display.
Video CDs with PBC
When a Video CD (Version 2.0) or Super Video CD with
Playback Control functions (PBC) is loaded, a menu will
appear on the screen.
JPEG files
Select an item using the number buttons to start playback.
• Some discs or USB flash drive may automatically start
playback.
• Press 6 to advance to the next page.
Press 7 to return to the previous page.
• If you press TITLE during playback, the menu will
appear on the screen.
When in stop mode, use q/w to select a picture in
1
the directory list.
After a short wait a thumbnail of the picture will
appear on the right.
Turning on or off the PBC function
Press MENU to turn the PBC function on or off. If you
press MENU during playback, playback will stop.
• Some photos may appear distorted due to the
configuration or characteristics of the disc. Larger
photos may take a short while to appear due to their
larger data size.
When the PBC function is off:
If you press 1/3 in the stop mode, playback will start
Press ENTER or 1/3 to viewing the picture at
from the first track.
2
full-screen size.
• When viewing at full-screen size, press 7/6
to view a previous or next photo. You can also use
e/r to rotate the image.
When the PBC function is on:
If you press 1/3 in the stop mode, a menu will appear
on the screen.
• When viewing at full-screen size, press 2 to
display a number of thumbnails at a time on the
screen.
Select an item using the number buttons to start playback.
– You can use q/w/e/r to select a particular photo and
then press ENTER to view that image at full-screen size.
– Select “Slide Show” to selections played in a random
order.
– Select “Menu” to display “REMOTE KEY
FUNCTION” list.
– Select “e Prev” to display previous screen of
thumbnail images.
– Select “Next r” to display next screen of thumbnail
images.
• Press MENU to exit thumbnail or full-screen
views.
En
20
Basic Operations for iPod, Disc and
USB Flash Drive
Selecting a Chapter or Track
Use the number buttons to select tracks or chapters for
playback.
For instance, to select track number 35, press 10+, 10+,
10+ and 5.
To select a MP3 or WMA file, enter 3 digit numbers.
As an example, to select number 5, press 10/0, 10/0 and
5. (Optionally, you may press just the number 5 and then
wait a few seconds.)
Pausing playback (Freezing the picture)
Press 1/3 to pause audio playback.
Any DVD or Video CD image is frozen.
Press 1/3 again to restart playback.
Caution
• If this unit is left in “pause” mode for an extended period
of time with the screen saver set to on, the screen saver
will automatically start on the television. If the screen
saver is set to off, damage to your television or the player
may occur.
Selecting the menu item (iPod)
Press q/w to scroll to the menu item you want, and then
press ENTER.
Pausing playback (iPod)
Going back to the previous menu (iPod)
Press 1/3 or 2. Playback stops at the current position.
Press MENU.
• To resume playback, press 1/3 again.
This button has the same functions as its iPod counterpart.
Stopping playback (DVD only)
Selecting Video Output (iPod)
When 2 is pressed, playback is stopped, and the display
shows “Press Play Key To Continue”. Pressing 1/3 to
continues playback.
This setting is for switching the output signal of the video
from iPod. Either the “Component” or “Composite” can
be selected. Press SETUP to switch video output signal
when “iPod” is selected as the input source.
`Component
If the component connection is used, select this
option.
`Composite
To cancel resume mode, press 2 (in the stop mode), 0,
INPUT or 9 ON/STANDBY.
Skipping Playback
If the composite connection is used, select this
option.
Press 7/6 repeatedly until the desired chapter or
track is found. The selected chapter or track will be played
from the beginning.
Note
• Make sure that the video output signal is selected before you
insert the iPod into the dock.
Skipping Playback (iPod only)
• The iPod (5th generation) only supports composite video output,
so make sure you select “Composite” and connect to the
television using the composite video terminal.
• The iPod nano (1st, 2nd generation) do not have a video signal
output function, so cannot playback video on an external
television.
Press 7 twice or more if you want to play the previous
songs of iPod.
Searching for a part of a chapter or
track
Selecting Audio
To Search quickly the disc in the forward or reverse
direction, press 5/4 during playback.
Many DVD discs include audio in different languages, as
well as stereo and multi-channel surround versions of the
sound track. CDs and Video CDs allow the left, right or
stereo channels to be selected.
Pressing AUDIO changes between the different audio
tracks available, and the result is shown on screen.
• It may be necessary to change the audio on some discs
using the on-screen disc menu.
• Some discs cannot have their audio changed in the way
described here, as well as some discs which only have
one audio stream. If you attempt to select different audio
with these discs, the prohibit icon “a” is shown on
screen.
Press 1/3 when the part you want to listen to is found.
Each time 5/4 is pressed, the search speed changes
as follows:
x2, x4, x8, x16, x32, normal speed
• The sound is muted during playback of DVD and VCD.
Searching for a part of a song (iPod)
Hold down 5 or 4 and release it when the part you
want to listen to is found.
En
21
Selecting Subtitles
Repeat and Shuffle Playback
Repeated presses of SUBTITLE cycle through available
languages on a disc.
Each time REPEAT is pressed, the mode is changed as
follows:
• Subtitles do not always appear immediately after the
language has been selected. It may take a few seconds
until the subtitles appear.
■ DVD
`Chapter, Title, All, Shuffle, No display
• Some captions on some discs cannot be removed or
changed using this button. Some discs may have only
one sub-caption language, in which case, the choice is
obviously restricted to one subtitle or no subtitles.
• It may be necessary to change the subtitles on some discs
using the on-screen disc menu.
• Some discs cannot have their subtitles changed in the
way described here. If you attempt to select a different
subtitle with these discs, the prohibit icon “a” is shown
on screen.
■ MP3/WMA
®
■ DivX (excluding North American models)
`Repeat One, Repeat All, Shuffle, Off
■ VCD/CD
`Track, All, Shuffle, No display
• This feature is not available for some discs. The
“prohibit” mark is shown on screen in such cases.
• If one of the following buttons is pressed, repeat mode
will be cancelled:
9 ON/STANDBY, 0, INPUT
■ iPod
Changing Camera Angle
`Repeat 1 (repeat one song), Repeat All (repeat all the
songs in the list), Repeat Off
When a scene recorded with multiple angles is played, the
angle icon appears on the screen. Each time you press
ANGLE while the angle icon is displayed, the camera
angle changes.
• When you select “One”, the Repeat One icon (
appears on the display of iPod.
)
• When you select “All”, the Repeat icon (
on the display of iPod.
) appears
• If you attempt to select a different angle with a disc
which no other angle is recorded, the prohibit icon “a”
will be displayed.
• ANGLE does not work during pause mode.
Repeat chapter/Repeat track/Repeat one
The currently selected chapter/track/file will be played
repeatedly. If another chapter/track/file is selected during
repeat playback, the newly-selected chapter/track/file will
repeat.
Picture Zoom
To zoom the picture, press ZOOM during playback.
Each time ZOOM is pressed, the magnification level
changes as follows:
Repeat title (DVD only)
The currently selected title will be played repeatedly.
■ DVD, VCD
Repeat all
®
■ DivX (excluding North American models)
All the contents in the disc will be played repeatedly.
`2x, 3x, 4x, 1/2, 1/3, 1/4, Normal
Shuffle
■ JPEG
The whole contents of the disc will be played randomly.
`100%, 125%, 150%, 200%, 150%, 125%, 100%, 75%,
50%, Normal
A-B Repeat Playback
• You can shift the zoom point by using e/r during zoom
playback.
You can Repeat Playback of a designated section.
Start playback and designate the point at which
the A-B repeat should start (point A) by pressing
A-B.
Slow Motion
1
For video discs only (DVD and VCD).
To play a disc in slow motion, press SLOW. Each time
SLOW is pressed, the speed changes as follows:
“
” appears on the screen.
A
When the point at which repeat playback should
end (point B) is reached, press A-B again.
2
■ DVD
`1/2, 1/4, 1/8, 1/16, 1/2, 1/4, 1/8, 1/16, r
“
” appears on the screen.
AB
The designated section will be played repeatedly.
■ VCD
®
■ DivX (excluding North American models)
• To fast-forward to point B after designating point A,
press 4.
`1/2, 1/4, 1/8, 1/16, r
To resume normal playback, press 1/3.
• The sound is muted during slow-motion playback.
• To cancel the A-B Repeat, press A-B again.
En
22
Changing the Display Mode
Time Search (MP3/WMA)
Each time DISPLAY is pressed during playback,
You can start playback from the specified hour/minute.
following information appears on the screen.
During playback, press SEARCH.
1
■ DVD
To search within the entire disc
Press SEARCH once.
“- - -” is highlighted on the screen.
`Title Elapsed time
`Title Remain time
`Chapter Elapsed time
`Chapter Remaining time
`Display off
To search within the current track
Press SEARCH twice.
“- - : - -” is highlighted on the screen.
■ CD/Video CD
`Single Elapsed time
`Single Remain time
`Total Elapsed time
`Total Remain time
Enter your desired hour and minute using the
number buttons.
For example, if the length of the current file is
3 minutes, enter a number smaller than 3 minutes.
Playback starts from the selected part.
2
®
■ DivX (excluding North American models)
`Title Elapsed time
`Title Remain time
`Chapter Elapsed time
`Chapter Remaining time
`Display off
Chapter Search/Time Search (DVD)
Chapter Search
You can start playback from the beginning of the specified
chapter.
Time Search (VCD/CD)
You can start playback from the specified hour/minute.
During playback, press SEARCH.
1
To search within a chapter/title of the disc
Press SEARCH once.
“T: - - / - - C: - - / - -” is highlighted on the screen.
During playback, press SEARCH.
1
To search within the entire disc
Press SEARCH once.
To search within the entire disc
Press SEARCH twice.
“TITLE - - / - - TIME: - - : - -” is highlighted on the
screen.
“DT: - - : - -” is highlighted on the screen.
To search within the current track
Press SEARCH twice.
“TT: - - : - -” is highlighted on the screen.
To search within the current chapter
Press SEARCH 3 times.
“CHAPTER - - / - - TIME: - - : - -” is highlighted
on the screen.
To select a track of the disc
Press SEARCH 3 times.
“T: - - / - -” is highlighted on the screen. Then, enter
the track number using the number buttons. (For
example, when you want to select track 2, press 2.)
Enter your desired title number, chapter number
or time using the number buttons.
Playback starts from the beginning of selected title
number, chapter number or time.
2
Enter your desired hour and minute using the
number buttons.
For example, if the length of the current track is
3 minutes, enter a number smaller than 3 minutes.
Playback starts from the selected part.
2
Chapter Search/Time Search (DivX®)
– excluding North American models
Chapter Search
You can start playback from the beginning of the specified
chapter.
During playback, press SEARCH once.
“SELECT: - - -” appears on the screen.
1
Enter your desired file number (3 digit) using the
number buttons.
Playback starts from the beginning of selected file.
2
En
23
Time Search
Programmed Playback (MP3/WMA)
You can start playback from the specified hour/minute/
second.
If another source is selected, press DVD or
iPod/USB once or twice to select “DVD Source”
or “USB Source”.
• You can also select “DVD Source” or “USB
Source” by using INPUT on the unit.
1
During playback, press SEARCH twice.
“GO TO -:- -:-” appears on the screen.
1
Enter your desired hour, minute and second using
the number buttons.
Playback starts from the selected part.
2
Select a file using q/w/e/r and press PROG.
2
The file is added to the programme list.
Press MENU once to display the programme list.
3
4
Programmed Playback (DVD/VCD/CD)
Highlight the first file in the programme list using
q/w/e/r.
Up to 20 chapters/tracks can be programmed in the
desired order.
Press ENTER to start programmed playback.
5
• The programmed contents will be cleared by using
buttons as follows:
If another source is selected, press DVD to select
“DVD Source”.
• You can also select “DVD Source” by using
INPUT on the unit.
1
INPUT (LINE, USB, FM), 0 (in DVD mode),
9 ON/STANDBY
Press PROG.
2
The programme list appears on the screen.
• To cancel the programme mode, press PROG
again, or select “EXIT” using q/w/e/r and press
ENTER.
Programmed Playback (DivX®)
– excluding North American models
If another source is selected, press DVD or
iPod/USB once or twice to select “DVD Source”
or “USB Source”.
• You can also select “DVD Source” or “USB
Source” by using INPUT on the unit.
Enter your desired “TITLE”, “CHAPTER” or
1
3
“TRACK” using the number buttons.
For example, to enter number 5, press 5.
Repeat this step to programme more titles, chapters
or tracks.
• If you made a mistake, move the cursor on the
track number and overwrite it using the number
buttons.
Press 2 when it starts playing.
2
3
Select a file using q/w/e/r and press PROG.
The file is added to the programme list.
• To programme more than 11 chapters/tracks, press
6 to advance to the next programme page (or
select “Next r” using q/w/e/r and press
ENTER). Press 7 to return to the previous page
(or select “e Prev” using q/w/e/r and press
ENTER).
Press MENU once to display the programme list.
4
5
Highlight the first file in the programme list using
q/w.
Press ENTER or 1/3 to start programmed
6
When the selection of chapter/track numbers is
playback.
4
• The programmed contents will be cleared by using
buttons as follows:
completed, select “START” using q/w/e/r and
press ENTER to start programmed playback.
• During programmed playback, the number buttons
do not work.
• When playback ends, the programme is cleared.
• The programmed contents will also be cleared by
using buttons as follows:
INPUT (LINE, USB, FM), 0 (in DVD mode),
9 ON/STANDBY
0, 9 ON/STANDBY, 2, INPUT (LINE, USB,
FM)
En
24
Settings
Settings
`4:3 PANSCAN:
Introduction
This mode is used with 4:3 televisions. 4:3 images
are displayed normally. When showing 16:9
programmes, the full height of the screen is
displayed, and the left and right part of the image are
cut off.
This chapter describes how to use the SETUP menu.
Most settings and adjustments are required to be set when
you first use the system.
Turn on the unit and the connected television or
monitor.
1
• The SETUP menu is available only in the “DVD
Source” mode or the “USB Source” mode. If
another source is selected, press INPUT on the unit
to select the “DVD Source” or the “USB Source”.
• You can also use the remote control’s DVD or
iPod/USB to select source.
4:3 picture
16:9 picture
`4:3 LETTERBOX:
This mode is used with 4:3 televisions. 4:3 images
are displayed normally. 16:9 images are visible at
their full width, but there are blank area at the top
and bottom of the screen.
Press SETUP.
The SETUP menu appears on the screen.
2
• To exit the SETUP menu, press SETUP again.
• Although it is possible to enter the SETUP menu
during playback (or resume mode), not all menu
functions will be available. To expand the number
of available functions, press 2 twice.
Use q/w/e/r to navigate the menus.
3
If no cursor is visible on the screen, use e/r to
4:3 picture
16:9 picture
select a page.
`16:9:
Use with a 16:9 wide television.
• Use q/w to highlight menu items within the
selected page.
• Press e to return to the upper menu.
Press r to enter the menu item.
4
5
Use q/w to select the options within the menu
item, and press ENTER to confirm the entry.
Individual menu functions are described.
Repeat steps 3 through 5 as required.
4:3 picture
16:9 picture
• Some wide-screen discs that do not permit the Pan Scan
mode playback are automatically played in Letter Box
mode.
Press SETUP to exit the SETUP menu.
6
• Depending on the DVD, “4:3 LETTERBOX” may be
selected automatically instead of “4:3 PANSCAN” and
vice versa.
• If “16:9” is selected and a normal TV is connected, 16:9
content will appear distorted during playback (objects
look thin).
GENERAL SETUP
TV DISPLAY
The shape of the television or monitor may not match the
shape of the movie frame. To avoid distortion on older
televisions, you may need to change the way in which the
image is displayed. Televisions use a 4:3 aspect ratio;
high-definition televisions use 16:9 aspect ratio (as do
movies).
Note
• You may need to read your television’s manual in conjunction
with this section in order to achieve the best results. Some discs
do not allow the aspect ratio to be changed and you will therefore
have to change the aspect ratio on the TV.
Make this setting while playback is stopped; you
cannot do this while playing back a disc.
En
25
OSD (ON SCREEN DISPLAY) LANGUAGE
3D PROCESSING
Select the desired language for on screen menus of the
unit from the following:
(European and North American)
`ENGLISH
`FRANÇAIS
`DEUTSCH
`ITALIANO
`ESPAÑOL
(Hong Kong)
`English
■ REVERB MODE
This setting provides following sound effects:
`OFF
`CONCERT
`LIVING ROOM
`HALL
`BATHROOM
`CAVE
`ARENA
`CHURCH
`Chinesetrad
• This function is effective only when playing back a DVD
disc recorded with Dolby Digital. This control has no
effect on other discs.
SCREEN SAVER
`ON:
• The overall effect of this setting depends on the disc
being played, the amplifier, and the speakers used for
playback.
The screen saver starts up if nothing is played back
and no operations are performed for 4 minutes.
`OFF:
NIGHT MODE
The screen saver does not start up.
`ON:
DIVX CODE
Applies dynamic range control to Dolby Digital
material, reducing the volume of loud sounds, and
increasing the volume of quiet ones. This is useful
for spoken word material, and nighttime listening
etc.
(excluding North American models)
`OK:
®
Display the DivX registration code.
`OFF:
AUDIO SETUP
Turns off the audio dynamic compression.
DIGITAL AUDIO SETUP
• This function is effective only when playing back a DVD
disc recorded with Dolby Digital. This control has no
effect on other discs.
■ DIGITAL OUTPUT
• The overall effect of this setting depends on the disc
being played, the amplifier, and the speakers used for
playback.
`OFF:
Select this when you do not use the COAXIAL
DIGITAL AUDIO OUT jack.
No signal is output from this jack.
`ALL:
AUDIO SYNC
Select this when the unit is connected to an audio
component equipped with a built-in Dolby Digital
decoder via the COAXIAL DIGITAL AUDIO OUT
jack.
This setting can cause delays in the sound signal in 10 ms
increments ranging from 0 ms to 200 ms (only for digital
signals recorded on a disc or stored in a USB drive;
unavailable for analog signals coming from LINE 1 or 2).
`PCM only:
Depending on the TV, it may take approximately 100 ms
(0.1 sec.) for an image to appear after video signals are
input, causing the image to appear after the sound coming
from the unit is heard.
Select this when the unit is connected to an audio
component such as amplifier/receiver, CD recorder
or MD deck via the COAXIAL DIGITAL AUDIO
OUT jack.
• If this happens or audio and video synchronization
creates a less than optimal viewing experience, adjust the
delay using e (decrease) or r (increase).
DOLBY DIGITAL SETUP
■ DUAL MONO
`STEREO:
Left channel is output from the left speaker, and right
channel is output from the right speaker.
`L-MONO:
Left channel is output from the front left and right
speakers.
`R-MONO:
Right channel is output from the front left and right
speakers.
En
26
HDMI SETUP
VIDEO SETUP
■ HDMI
`AUTO:
TV MODE
This setting allows the selection of interlaced
(INTERLACE) or progressive-scan (PROGRESSIVE)
video from the component video outputs.
`PROGRESSIVE:
For progressive scan TV: turn on the progressive
scan mode.
`INTERLACE:
Select this to have the signal output when your TV or
monitor is connected to the HDMI OUT jack.
`OFF:
Select this when you do not use the HDMI OUT
jack.
No signal is output from the HDMI OUT jack.
■ RESOLUTION
You can specify the output resolution for the HDMI
output.
`OFF
`480p 60Hz
`720p 60Hz
`1080i 60Hz
`1080p 60Hz
`576p 50Hz
`720p 50Hz
`1080i 50Hz
`1080p 50Hz
For ordinary TV: turn on the interlace mode.
• When your TV is not compatible with progressive scan,
never select “PROGRESSIVE”. No picture will be
shown on the monitor.
In case you select “PROGRESSIVE” by mistake,
disconnect the connection of the unit and the TV, and
then connect in again. And change the setting to
“INTERLACE”.
COLOR SETTING
You can adjust some parameters of video picture.
Use e/r to select the parameter and change the value,
then press ENTER.
■ SHARPNESS
This adjusts the sharpness of the picture shown on the
monitor.
`HIGH
`MEDIUM
`LOW
■ BRIGHTNESS
This adjusts the brightness of the picture.
`-20 to +20
■ CONTRAST
This adjusts the picture contrast.
`-16 to +10
■ GAMMA
This adjusts the gamma value of the picture.
`HIGH
`MEDIUM
`LOW
`NONE
■ HUE
This adjusts the green/red balance of the picture.
`-9 to +9
■ SATURATION
This adjusts the saturation level.
`-9 to +9
■ LUMA DELAY
This adjusts the luma delay.
`0 T
`1 T
En
27
PREFERENCE
PASSWORD SETUP
TV TYPE
PASSWORD MODE
`PAL:
You can temporarily unlock discs for playback according
Select this when the unit is connected to a PAL TV.
`AUTO:
Select this when the unit is connected to a Multi TV.
`NTSC:
Select this when the unit is connected to an NTSC
to the level.
To change this setting, select “ON” or “OFF”, enter your
password, and press ENTER.
`ON:
You need a password to change the level of parental
TV.
control.
`OFF:
AUDIO, SUBTITLE, DISC MENU
You can change the level of parental control without
a password. You cannot temporarily unlock discs for
playback.
You can select a preferred language for audio, subtitle and
disc menu.
PASSWORD
• When you select a preferred language that is not
recorded on the DVD, one of the recorded languages is
automatically selected.
• You can override the “AUDIO” setting by pressing
AUDIO on the remote control while a DVD disc is
playing.
• You can override the “SUBTITLE” setting by pressing
SUBTITLE on the remote control while a DVD disc is
playing.
• Select “OFF” to turn subtitles off. Note that subtitles on
some discs cannot be removed even when you select
“OFF”.
You can set a new password for parental control.
The default password is 2580.
Select “CHANGE” and press ENTER.
1
2
Enter 2580 (or your privacy password) using the
number buttons.
Enter a new password.
3
4
5
Enter the same password again to confirm.
Press ENTER.
PARENTAL
Note that you will need your password to change the
level of control in the future as well as to temporarily
unlock discs for playback.
Playback of some DVD discs can be limited depending on
the age of the users. The parental control system allows
the playback limitation level to be set by the parent.
If you forget your password, use 2580.
Note
• The lower the level, the stricter the limitation.
• If the rating of the loaded DVD disc is higher than the level you
set, the system will require a password. Enter your password and
press ENTER to start playback.
Select the desired parental control level from the
menu, then press ENTER.
1
You will be prompted to enter your password. Use
the number buttons to enter 2580 (or your privacy
password if already established).
2
• No need to enter a password if “PASSWORD
MODE” is set to “OFF”.
DEFAULT
All the items in the SETUP menu (except for the password
and parental control) will be reset to the default settings.
En
28
Listening to the FM Radio
Listening to the FM Radio
Press FM to select “FM Radio”.
How to select preset stations
1
2
Hold down q TUNING w for more than 1 seconds
Press FM to select “FM Radio”.
1
2
to select the station you want to listen to (Auto
selection).
Select a preset channel using e PRESET r.
When a station is tuned in, the tuning process will
stop automatically.
Repeat this step until the station you want to listen to
is found.
• You can also select a preset channel by using
e PRESET r on the unit.
• If you want to stop the tuning process, press
q TUNING w.
RDS (Display Setting of the FM)
– excluding North American models
Selecting stations which cannot be tuned automatically
(Manual selection)
The Radio Data System (RDS) is a broadcasting service
which allows stations to send additional information along
with the regular radio programme signal.
When q TUNING w is pressed momentarily, the
frequency changes by a fixed step.
Press q TUNING w repeatedly until the station you want
1
to listen to is found.
Press DISPLAY.
Each time DISPLAY is pressed, the RDS mode is
changed as follows:
FM MODE
2
Pressing FM MODE alternates between Auto mode and
Mono mode.
■ PS (Programme Service name)
Automatically displays the FM station name when
PS data is received.
■ Auto Mode
FM stereo or monaural broadcasts are received in the
same mode as the signal.
■ PROG TYPE (Programme Type)
Displays the programme type. If there is no PTY
data, “NO PTY” will be displayed.
■ Mono Mode
To compensate for weak FM stereo reception, select this
mode. Reception will now be forced to monaural,
reducing unwanted noise.
■ RDS CLOCK
Displays the information about times provided
from the station.
If the reception is poor
If there is no time data, “NO CT” will be
displayed.
For the best reception, rotate the FM antenna until you get
stations clearly.
Preset Tuning
RDS only works in areas where RDS broadcasts are
available.
You can store up to 20 FM stations.
Automatic Memory Presetting
Press FM to select “FM Radio”.
1
2
Press SEARCH.
Up to 20 of the received stations in your area will be
stored automatically.
Manual Memory Presetting
Tune in a station.
1
2
3
Press MEMORY.
Select a preset channel to store the station using
e PRESET r, and then press MEMORY.
En
29
Listening to an External Source
Wake Up Timer
The unit can be programmed to turn on at a specified time.
• Adjust the clock before setting the timer.
Connect a cassette tape deck etc. to LINE 1 IN
jack of the unit using commercially-available
RCA cables.
1
If the unit is on, press 9 ON/STANDBY to turn
1
the unit standby.
Or Connect the audio output jack of a portable
audio player to the LINE 2 IN jack of the unit.
Press CLOCK to show the time on the display.
2
3
• When you connect the portable audio player to
LINE 2 IN jack of the unit, use the stereo mini plug
cable.
Press TIMER.
“Timer Set” appears on the display, and the “hour”
value starts blinking.
Press LINE to select “LINE1 Source” or “LINE2
Source”.
2
• When no button is pressed for 30 seconds, the
timer setting mode will be cancelled.
Play the source, and adjust the volume using
3
Press q VOL w to set the start time (hour), and
4
q VOL w of the unit and of the audio player.
You can also adjust the volume by using the
VOLUME knob on the unit.
then press TIMER.
The “minutes” value starts blinking.
Press q VOL w to set the start time (minute), and
5
then press TIMER.
The “Off” starts blinking.
Sleep Timer
Press q VOL w to turn On or Off the timer
6
The power can be switched off after a specified amount
of time.
function, and then press TIMER.
Select “On” to turn the timer function on. The
TIMER indicator ( ) appears on the display.
When you do not use the timer, select “Off”. (The
TIMER indicator disappears from the display.)
Press SLEEP repeatedly until desired time
appears on the display.
`SLEEP 10, 20, 30, 60 or 90:
The power will be switched off 90 (60, 30, 20,
or 10) minutes later.
Turn the unit on and prepare the source.
• To play a disc, select “DVD Source” using INPUT
and set a disc.
• To play a USB flash drive, select “USB Source”
using INPUT and set a USB flash drive.
• To listen to the FM, select “FM Radio” using
INPUT and tune in a station.
7
`SLEEP OFF:
The sleep timer is off.
• If you want to check the remaining time, press
SLEEP once. The remaining time will be
displayed for 3 seconds, and then return to the
normal display.
Press 9 ON/STANDBY to turn the unit standby.
8
• The unit will turn on at the specified time every
day.
• The unit turns on with the source that was last
selected.
Do not forget to turn the unit to standby, or the timer
will not work.
If the timer reaches the timer-on time, the unit is set to
“SLEEP 60” automatically and the power will be turned
standby 60 minutes later.
If you want to listen continuously, press SLEEP
repeatedly to select “SLEEP OFF” before reaches the
timer-off-time.
En
30
Troubleshooting
Troubleshooting
To keep the warranty valid, never try to repair the system
yourself. If you encounter problems when using this unit,
check the following points before requesting service.
DR-645
■ No power
Ensure that the AC power cord of the apparatus is connected
properly.
If normal operation cannot be obtained, unplug the
power cord from the outlet and plug it again. This
resets the internal micro-computer which can be
disturbed during electrical storms, power
interruptions, etc.
Ensure that there is power at the AC wall outlet.
Press 9 ON/STANDBY to turn the unit on.
■ No disc detected
If unplugging the AC power cord does not solve the
problem, try the following procedure to reset the
internal micro-computer.
Note that resetting the unit will delete your radio presets
and custom settings.
Insert a disc.
Check if the disc is inserted upside down.
Wait until the moisture condensation at the lens has cleared.
Replace or clean the disc.
Use a finalized CD or correct format disc.
■ Resetting the System setup
1. Turn the unit on.
■ No picture
2. Press 2 for 3 seconds while holding down the
Check the video connection.
1/3.
Turn on the TV to the correct Video-In channel.
Progressive scan is activated but the TV does not support
progressive scan.
■ Black and white or distorted picture
The disc does not match the TV color system standard
(PAL/NTSC).
Sometimes a slight picture distortion may appear. This is not
a malfunction.
Clean the disc.
A distorted picture may appear during progressive scan setup.
■ The aspect ratio of the TV screen cannot be
changed even though you have set the TV
display format
3. Release 2 and 1/3 when “DR-645**” appears
The aspect ratio if fixed on the loaded DVD disc.
on the display.
The aspect ratio may not be changed for some TV systems.
4. Press 2.
■ No sound or poor sound
■ Resetting the DVD setup
To reset the custom settings on OSD to its default value,
try the following procedure.
Adjust the volume.
Disconnect the headphones.
1. Turn the unit on.
Check that the speakers are connected correctly.
Check if the stripped speaker wires are clamped.
2. Press SETUP. Setup menu appears on the display.
3. Select “PREFERENCE”, and then select
“DEFAULT”.
■ Remote control does not work
4. Select “RESET”.
Before you press any function button, first select the correct
source.
Reduce the distance between the remote control and the unit.
Insert the battery with its polarities (+/-) aligned as indicated.
Replace the battery.
Aim the remote control directly at the sensor on the front of
the unit.
En
31
■ Disc does not play
iPod
Insert a readable disc and ensure that the label side faces up.
■ No Sound or Video
Check the disc type, color system and regional code. Check
for any scratches or smudges on the disc.
Make sure your iPod is connected properly.
If there’s no video, make sure your iPod supports TV out.
Make sure your iPod is playing.
Press MENU to exit the system setup menu.
Disable the password for parental control or change the rating
level.
On your TV, make sure that the video input to which the unit
is connected is selected.
If condensation is suspected, unplug the AC power cord and
leave DR-645 for two to three hours in the room temperature
before playing any discs.
Make sure all plugs are pushed in all the way.
Try resetting your iPod.
Video on the iPod LCD screen is not output to the monitor.
Only the video content is output.
■ Poor radio reception
Increase the distance between the unit and your TV or VCR.
Fully extend the FM antenna.
The iPod video signal is not output via HDMI.
Connect an outdoor FM antenna instead.
■ Remote Control does not work
Make sure your iPod is seated properly on the dock
connector. If your iPod is in a case, it may not connect
properly, so always remove the case before inserting your
iPod into the DR-645.
■ Unable to select Progressive Scan
Make the component video connection.
Your iPod cannot be controlled while it’s displaying the
Apple logo.
■ Audio or subtitle languages cannot be set
The disc is not recorded with sound or subtitles in multiple
languages.
If you’re using the remote control, be sure to point it toward
DR-645 when you want to control your iPod.
The audio or subtitle language setting is prohibited on the
disc.
Try resetting your iPod.
Changing setting will not take effect if done while pausing or
video playback.
■ Cannot display some files in USB flash drive
The number of folders or files in the USB flash drive has
exceeded a certain limit. This phenomenon is not a
malfunction.
■ Others
Depending on the backlight setting on your iPod, the display
may become dim during use. If the display is hard to see,
change the backlight setting on your iPod.
The formats of these files are not supported.
Connecting the iPod to the dock automatically turns on the
TV output.
■ USB flash drive not supported
The USB flash drive is incompatible with the unit. Try
another one.
If the iPod does not function normally even when inserted in
the dock connector, check that the iPod is firmly inserted. If
the iPod still does not function after checking, remove the
iPod from the dock, wait a few seconds, and insert it again.
■ Timer does not work
Set the clock correctly.
Switch on the timer.
■ Clock/timer setting erased
Power has been interrupted or the power cord has been
disconnected.
Reset the clock/timer.
En
32
Specifications
Amplifier Section
DVD Player Section
Rated Output Power
Signal System
NTSC/PAL
All channels:
(North American)
Video Output Level and Impedance
20 watts minimum continuous power per
channel, 8 ohm loads, 2 channels driven
from 20 Hz to 20 kHz, with a maximum
total harmonic distortion of 10% (FTC)
1.0 Vp-p/75 Ω negative sync, RCA
(Composite)
1.0 Vp-p/75 Ω RCA (Component Y)
0.7 Vp-p/75 Ω RCA (Component PB/PR)
(Others)
Component Video Frequency Response
5 Hz - 13 MHz
Component Video Resolution
2 ch × 40 W at 4 ohms, 1 kHz (IEC)
THD (Total Harmonic Distortion)
10% (Power Rated)/0.05%
30 (1 kHz, 4 Ω, 1 W)
Input Sensitivity and Impedance
600 mV/47 kΩ (LINE)
Rated RCA Output Level and Impedance
1000 mV / 1.5 kΩ (LINE OUT)
480p 60 Hz, 720p 60 Hz, 1080i 60 Hz,
1080p 60 Hz, 576p 50 Hz, 720p 50 Hz,
1080i 50 Hz, 1080p 50 Hz
Damping Factor
HDMI Resolution
480p 60 Hz, 720p 60 Hz, 1080i 60 Hz,
1080p 60 Hz, 576p 50 Hz, 720p 50 Hz,
1080i 50 Hz, 1080p 50 Hz
HDMI Audio Format PCM
Frequency Response 20 Hz to 20 kHz, +0 / -3 dB
Tone Control Characteristics
HDMI Version
1.2a
HDMI Connector
A Type
11.5 dB, 80 Hz (BASS)
10 dB, 10 kHz (TREBLE)
+8.5 dB, 80 Hz (S.BASS)
Frequency Response (Digital Audio)
DVD Liner Sound: 4 Hz to 44 kHz (96 kHz)
4 Hz to 22 kHz (48 kHz)
Audio CD: 4 Hz to 20 kHz (44.1 kHz)
Signal-to-Noise Ratio 80 dB
Audio Dynamic Range
80 dB
Signal-to-Noise Ratio 72 dB (LINE, IHF-A)
Speaker Impedance 4 Ω - 16 Ω
FM Tuner Section
THD (Total Harmonic Distortion)
0.25% (1 kHz)
Wow and Flutter
Below threshold of measurability
Tuning Frequency Range
Audio Output/Impedance (Digital/Coaxial)
0.5 V (p-p)/50 Ω
Audio Output/Impedance (Analog)
1.6 V (rms)/3.3 kΩ
(North American)
87.5 MHz to 107.9 MHz
(Others)
87.5 MHz to 108.0 MHz, RDS
General
Power Supply
(North American)
AC 120 V, 60 Hz
(Others)
AC 220 - 240 V, 50/60 Hz
Power Consumption 36 W
Stand-by Power Consumption
0.9 W
Dimensions (W × H × D)
215 mm × 108 mm × 348 mm
(8-7/16" × 4-1/4" × 13-11/16")
Weight
4.4 kg (9.7 lbs.)
Operation Condition Temperature/Humidity
5 °C ~ 35 °C (41 °F ~ 95 °F)/ 5% ~90%
Bus Power Supply (USB)
DC 5 V, 0.5 A
Disc Compatibility CD-R, CD-RW, DVD-R, DVD-RW, DVD-R
DL, DVD+R, DVD+RW, DVD+R DL, USB
(Discs that have not been properly finalized
may only be partially playable or not playable
at all.)
En
33
■ HDMI
Output
1
■ Video Outputs
Component
Composite
1
1
■ Audio Inputs
Analog
2 (LINE1/LINE2)
■ Audio Outputs
Digital
Analog
1 (Coaxial)
1 (LINE)
Subwoofer Pre Output
1
Speaker Outputs SPEAKERS (L/R)
Phones
■ Others
USB
1 (3.5 ø)
1
1
iPod Connector
• Design and specifications are subject to change
without notice.
• Weight and dimensions are approximate.
En
34
Memo
En
35
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE ELECTRONICS GmbH (UK BRANCH)
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
ONKYO CHINA LIMITED
Unit 1 & 12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung,
N.T., Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039
Y1009-2
SN 29400514A
(C) Copyright 2010 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 4 0 0 5 1 4 A *
|