CP-1050
Direct Drive Turntable
Instruction Manual
Names and functions of parts .....6
Assembly and installation............7
Preparatory adjustments.............8
1. Horizontal balance............................8
2. Stylus pressure.................................9
3. Anti-skating.......................................9
Connections..............................10
Playing records ......................... 11
Troubleshooting ........................12
Thank you for purchasing an Onkyo product.
Please read this manual thoroughly before making any
connections and plugging in your new Onkyo product.
Following the instructions in this manual will enable you to
obtain optimum performance and listening enjoyment from
your new product.
Please retain this manual for future reference.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without
the permission of the copyright holder.
8. Handling Notes
0 If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
0 Do not leave rubber or plastic items on this unit for a
long time, because they may leave marks on the
case.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact your
Onkyo dealer.
0 This unit’s top and rear panels may get warm after
prolonged use. This is normal.
0 If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be
sure to use it occasionally.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a clean
cloth. Don’t use abrasive cloths, thinners, alcohol, or
other chemical solvents, because they may damage
the finish or remove the panel lettering.
0 When you’ve finished using this unit, remove all
discs and turn off the power.
9. Installing this Unit
4. Power
0 Install this unit in a well-ventilated location.
0 Ensure that there’s adequate ventilation all around
this unit, especially if it’s installed in an audio rack. If
the ventilation is inadequate, the unit may overheat,
leading to malfunction.
0 Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may rise,
shortening the life of the optical pickup.
0 Avoid damp and dusty places, and places subject to
vibrations from loudspeakers. Never put the unit on
top of, or directly above a loudspeaker.
0 Install this unit horizontally. Never use it on its side
or on a sloping surface, because it may cause a
malfunction.
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC
230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug is
readily operable (easily accessible) at all times.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF mode
does not fully disconnect from the mains. If you do not
intend to use the unit for an extended period, remove
the power cord from the AC outlet.
0 If you install this unit near a TV, radio, or VCR, the
picture and sound quality may be affected. If this
occurs, move this unit away from the TV, radio, or
VCR.
10.Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this unit.
0 Moisture condensation can occur in the following
situations:
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select Standby
mode does not fully disconnect from the mains. If you
do not intend to use the unit for an extended period,
remove the power cord from the AC outlet.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
– The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat as sunshine, fire or the
like.
o not use this unit when there’s the possibility of
0 D
moisture condensation occurring. Doing so may
damage your discs and certain parts inside this unit.
If condensation does occur, unplug the power cord and
leave the unit for two to three hours in the room
temperature.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are
wet or damp. If water or any other liquid gets inside
this unit, have it checked by your Onkyo dealer.
3
Precautions
For U.S. and Canadian models
FCC CAUTION
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
For European Models
Declaration of Conformity
We declare, under our sole
responsibility, that this product
complies with the standards:
– Safety
– Limits and methods of
measurement of radio
disturbance characteristics
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Limits for harmonic current emissions
– Limitation of voltage changes, voltage fluctuations
and flicker
– RoHS Directive, 2011/65/EU
WEEE
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
For Canadian Models
NOTE:
CAN ICES-3 B/NMB-3 B
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows: The wire which is coloured blue must be
connected to the terminal which is marked with the letter
N or coloured black. The wire which is coloured brown
must be connected to the terminal which is marked with
the letter L or coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for the
ASTA mark or the BSI mark on the body of the fuse. If the
power cord’s plug is not suitable for your socket outlets, cut
it off and fit a suitable plug. Fit a suitable fuse in the plug.
4
Features
Supplied accessories
Before use, check whether the main unit and the
accessories below are supplied.
Professional manual record player with a focus
on sound quality
This is a manual player with simple functions that is
designed with the highest priority placed on the sound
quality for playing analog records. In terms of operations,
usability is ensured with fittings such as a lifter for
lowering and raising the tone arm. Also, the cartridge and
head shell can be replaced.
∫
Turntable
k
1
∫
∫
Rubber mat
k
1
Composed of highly reliable parts
High reliability parts such as a MDF-manufactured
cabinet for better sound quality, high rigidity aluminum
die-cast turntable, high sensitivity tone arm, MM-type
cartridge, etc., are used.
Counterweight
k
1
High precision and stable direct drive system
∫
Head shell/Cartridge
k
1
High precision rotating performance is achieved with a
quartz lock system. It is also equipped with an insulator to
absorb external vibrations effectively.
Luxurious finishing
∫
∫
Adapter for 45 rpm records
A superior finishing reflecting the quality of the raw
materials used is achieved by using a combination of
aluminum parts arranged on the base of the operating
unit and a cabinet with a soothing color tone.
k
1
Dust cover
k
1
∫
∫
Dust cover hinge
k
2
Pin cables with attached
grounding
k
1
∫
Power cord
k
1
*
In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and operations
are the same regardless of color.
5
Names and functions of parts
POWER button ( ON/ OFF): Press this button
to turn the unit on or off.
Speed selector button (33/45): Set this button
according to the record’s playing speed.
Center spindle
START/STOP button: Rotates/stops the turntable.
Locking nut: Use this to install the head shell.
Tone arm
Arm clamp: Secures the tone arm to the arm rest.
Arm rest: Table to mount the tone arm.
Lifter lever: Use this to lift and lower the tone arm.
Anti-skating knob: Use this to adjust the anti-skating.
Rubber mat
Turntable
Counterweight: Use this to balance the tone arm and
to adjust the stylus pressure.
Head shell
*
The turntable, rubber mat, counterweight and head shell are not
fitted at the point of purchase. Refer to “Assembly” on the next
page to assemble them.
6
Assembly and installation
3. Mounting the counterweight
Assembly
Mount the counterweight on the shaft at the back of the
tone arm.
0
Do not rotate the counterweight to a position where the
white center line on the shaft at the back of the tone
arm is no longer visible.
1. Mounting the turntable and rubber mat
Center line
Counterweight
1. Insert the turntable onto the center spindle.
0
Handle the turntable with care so that it does not
drop onto or hit the unit, tone arm, etc.
2. Lay the rubber mat on top.
Rubber mat
Turntable
Installation
Install the unit on a horizontal surface protected from vibrations.
0
0
0
0
Do not place the unit on top of the amplifier or speaker
system.
Install the unit away from the speaker system so as to
avoid the impact of vibrations and acoustic pressure.
Ensure the unit is not exposed to direct sunlight, dust,
humidity, and heat from a heating appliance.
This unit may cause interference to radio broadcast if
there is a radio nearby. Keep radios as far as possible
from this unit.
Center spindle
0
If you have any devices that emit high-intensity radio
waves near the unit, such as a cellular phone that’s
being used to make a call, the unit may output noise.
2. Mounting the head shell
Fit the head shell into the tone arm, keep it horizontal and
tighten the locking nut.
Adjust the unit horizontally
Place the unit where it is to be used and adjust the height
of the insulators to make the unit horizontal.
Head shell
Insulator
Locking nut
7
Preparatory adjustments
3. Release the arm clamp.
Handling the stylus
The tip of the stylus is extremely delicate. Be careful
not to break or bend the stylus when removing the
stylus cover. If the stylus tip is damaged, promptly
replace it with a new stylus. If a damaged stylus is
used, it will result in damage to the record.
1. Horizontal balance
Arm clamp
The horizontal balance of the tone arm needs to be
adjusted first in order to ensure that an appropriate stylus
pressure is applied on the record. Carry out the
adjustment with the power turned off.
4. Free the tone arm from the arm rest.
Leave the lifter lever in a lowered state.
Arm rest
Lifter lever
1. Set the anti-skating knob to “0”.
Anti-skating knob
5. Turn the counterweight to adjust the tone arm so that it
returns to an almost horizontal state (*) when the hand
is released. During adjustment, take care not to allow
the stylus to touch the rubber mat or the turntable.
2. Remove the translucent stylus cover, taking care not to
damage the stylus.
*
Ensure that the tone arm is balanced, so that the end of the tone
arm is neither too high nor too low.
Counterweight
Stylus cover
Head shell
Stylus
6. Return the tone arm to the arm rest and fix it with the
arm clamp.
8
Preparatory adjustments
2. Turn the counterweight in the direction of the arrow so
that the white center line on the shaft at the back of the
tone arm is at “3.5”.
2. Stylus pressure
0
When the counterweight is turned, the stylus
pressure adjustment ring also turns.
0
When using a cartridge and head shell other than
those supplied, adjust the stylus pressure to an
appropriate value to match the cartridge after re-
adjusting the horizontal balance.
First turn the scale of the stylus pressure temporarily to
“0” in a horizontally balanced state, and then adjust the
stylus pressure.
If the stylus pressure is too high or too low, the record
may not be played back correctly, or the stylus life may be
shortened, or the record may be damaged. Be sure to
adjust the stylus pressure to an appropriate value to
match the cartridge.
1. Turn the stylus pressure adjustment ring so that the
white center line on the shaft at the back of the tone
arm is at “0”.
0
Keep your fingers in contact with the stylus
pressure adjustment ring only and turn it so that the
counterweight does not turn at the same time.
Counterweight
Center line
Stylus pressure
adjustment ring
3. Anti-skating
When playing a record, a force pulling the stylus tip
towards the inner circumference is generated. This force
can be canceled by setting the anti-skating value to the
same stylus pressure.
1. Turn the anti-skating knob to adjust it to the same
scale as the stylus pressure. If the stylus pressure is
“3.0” or higher like the supplied cartridge, adjust it to
“3”.
Anti-skating knob
9
Connections
Amplifier
to an AC outlet
1. Connection with the amplifier
3. Mounting the dust cover
Connect the supplied pin cables with attached grounding
to the PHONO OUTPUT terminals on the rear panel of
the unit and the PHONO input terminals of the amplifier.
Connect the red plug to the R terminal and the white plug
to the L terminal respectively.
1. Insert the two supplied dust cover hinges fully into the
holder on the rear panel of the unit.
2. Adjust the square holes of the dust cover to the hinges
and insert them fully into the hinges.
In addition, connect the grounding line of the pin cables
with attached grounding to the GND terminal (ground
terminal) of the rear panel of the unit and the amplifier.
About the amplifier
If there is no PHONO input terminal on the amplifier
used, connect a commercial phono-equalizer between
the unit and the amplifier. See the instruction manual
of the phono-equalizer for the connection method.
Hinge
2. Connecting the power cord
Holder
Do not use a power cord other than the one supplied
with this unit. Before connecting the power cord,
connect all of your components.
Opening and closing the dust cover
Open and close the dust cover slowly. The stylus may
jump if the player is subjected to shock during a
musical performance.
Always connect the power cord to an AC outlet only after
connecting it to the AC INLET terminal of the unit.
Removing the dust cover
After opening the dust cover fully, hold the dust cover
at the back on both sides and pull it out from the top.
Disconnect the power cord only after turning the unit off.
To avoid electrical shock, always disconnect the power
cord from the AC outlet before disconnecting the other
end.
10
Playing records
5. Raise the lifter lever, hold the head shell’s finger hook,
and move the tone arm to the desired position over the
record.
Before playing the music
0 Release the arm clamp.
0 Turn on the power supply of the connected
amplifier and switch the input so that the sound of
this unit comes out. Keep the volume of the
amplifier low.
Lifter lever
6. Lower the lifter lever.
The tone arm will slowly descend until the stylus tip
touches the record and start playing the music.
0
When lowering the stylus onto a record, keep the
amplifier volume low so as not to create large
noises and adjust the volume after the stylus tip
touches the record.
To stop playing the music
1. Lower the volume of the amplifier and then raise the
lifter lever.
0
Lower the lifter lever to start playing the music
again.
2. Hold the finger hook of the head shell and lower the
lifter lever after returning the tone arm to the arm rest.
3. Press the START/STOP button.
POWER button
Speed selector
button
START/STOP
button
The turntable stops revolving.
1. Press the
supply.
POWER button to turn on the power
0
0
0
The player will not stop automatically even when
the record has finished playing.
Wait until the turntable stops revolving before
replacing records.
Secure the tone arm with the arm clamp if you are
not going to start playing the next tune immediately.
The indicator of the speed selector button lights up.
2. Put a record on the rubber mat.
0
If it is a record with a
large hole, fit the
4. Press the
supply.
POWER button to turn off the power
supplied adapter for 45
rpm records into the
center spindle.
0
Put on the stylus cover to protect the stylus tip if you
are not going to use it for a while.
3. Set the speed selector button according to the record’s
playing speed.
For European models
“33”: 33 1/3 rpm record
Auto-standby function: If the unit is not operated for
about an hour with the turntable stopped, it will
automatically go into the standby mode. (The indicator
of the speed selector button will go off.) Power
consumption is reduced in the standby mode.
Press the START/STOP button or the speed selector
button in the standby mode to return to the power on
state.
“45”: 45 rpm record
The indicator of the selected speed selector button
lights up.
4. Press the START/STOP button.
The turntable starts revolving.
11
Troubleshooting
No sound comes out after replacing the stylus
with a special replacement stylus (DN-105ST).
Before starting the procedure
Problems may be solved by simply turning the power
on/off or disconnecting/connecting the power cord,
which is easier than working on the connection,
setting and operating procedure. Try the simple
measures on both the unit and the connected device.
0
Fit the stylus properly until a clicking sound is heard.
The indicator of the speed selector button
blinks.
0
0
0
Check whether the supplied turntable is properly
plugged into the center spindle.
Check whether the rotation of the turntable is blocked
by anything.
The unit does not turn on.
0
Confirm that the power plug is securely plugged in to
an outlet.
Press the
POWER button once to turn off the power
0
Set the
pressing it once and then set it to the
pressing it again after waiting for 5 seconds or longer.
POWER button to the
OFF state by
supply and then press the
turn it back on.
POWER button again to
ON state by
Stylus does not lower onto record.
0
0
Lower the lifter lever.
Check whether the stylus pressure has been adjusted
correctly.
0
Check whether the tone arm is balanced horizontally.
No sound is produced.
Sound is too weak.
0
0
Check the input and volume of the amplifier.
If a commercial phono-equalizer is connected, check
whether its power supply is turned on.
0
0
Make sure the pin cables with attached grounding are
connected correctly.
If connected to an amplifier with no PHONO input
terminal, sufficient volume and the correct sound
quality cannot be obtained. In this case, connect a
commercial phono-equalizer between the unit and the
amplifier before use.
A low booming sound (hum or buzz) is heard
when music is played.
0
Check whether the pin cables with attached grounding
are connected correctly (including the grounding line).
Keep electrical appliances such as fluorescent lamps
and power cords as far away as possible from the pin
cables with attached grounding.
0
0
Check whether the head shell is securely fastened by
the locking nut.
Stylus jumps.
0
0
Check whether the unit is subject to any vibration.
Check whether the stylus pressure and anti-skating
are adjusted correctly.
0
0
Check whether there are any scratches or warps on
the record.
Remove any dust attached to the stylus tip.
12
Handling
Handling and maintenance of stylus
Take due care when handling the stylus as the stylus tip
is extremely delicate.
Remove any dust attached to the stylus tip using a brush
with a soft tip by brushing from the base of the stylus
towards the end. You can also use a special cleaner
available commercially for cleaning.
Replacing the stylus
The life-span of the stylus is normally about 500 hours but
varies greatly depending on the usage conditions. When
the stylus tip is worn out, high frequencies may go out of
pitch or the record may be damaged. Promptly replace
the stylus in this case. Use a special replacement stylus
(DN-105ST) to replace the stylus for the CP-1050. See
the manual supplied with the replacement stylus for the
replacement method.
Maintenance of records
Use a commercial record cleaner to wipe the records
thoroughly. If the record is dirty, the stylus may be
damaged, resulting in noise and jumping sounds.
When relocating the unit
Repackage the unit in the packaging it came in. If you no
longer have the packaging, do the following:
0
0
0
0
Take off the turntable and rubber mat and carefully
wrap them.
Remove the counterweight and head shell from the
tone arm and carefully wrap them.
Secure the tone arm with the arm clamp and then tie it
with a string so that it does not move.
Carefully wrap the unit in a blanket or soft paper.
13
Specifications
∫ Turntable section
Drive method
:
Direct drive
33 1/3 rpm, 45 rpm
0.15 % or less
Turning speed:
Wow and flutter:
Signal to noise ratio:
Turntable:
60 dB or above
Aluminum die-cast
Diameter 305 mm
Brushless DC motor
1.0 kgf-cm or above
Motor:
Starting torque:
∫ Tone arm section
Type:
Static balance, S-shaped tone arm
Effective length:
230 mm
15 mm
Overhang:
Tracking error angle:
Stylus pressure adjustment range:
Applicable cartridge weight range
(including a head shell):
Within 3o
0 g to 4 g
15 g to 20 g
∫ Cartridge section (OC-105)
Type:
MM
Load resistance:
Output voltage:
Stylus pressure:
Replacement stylus:
Cartridge weight:
Head shell weight:
47 k
3 dB
0.5 g
h
2.5 mV
3.5 g
d
d
DN-105ST
5 g
10 g
∫ General
Power supply:
(North American) AC 120 V, 60 Hz
(European) AC 220 - 240 V, 50/60 Hz
Power consumption:
(North American) 4 W
(European) 6 W
Standby power consumption:
(European) 0.4 W
Dimensions (W × H × D): 450 mm
k
158 mm
6-1/4"
k
367.5 mm
(17-11/16"
k
k 14-7/16")
Weight:
8.6 kg (19.0 lbs.)
Specifications and features are subject to change without
notice.
14
15
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku, OSAKA 541-0041, JAPAN
The Americas
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
For Product Support Team Only:
1-800-229-1687
Europe
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
Meridien House, Ground floor, 69 - 71 Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
China
(Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
(Mainland)
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
F1410-0
SN 29401915
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
* 2 9 4 0 1 9 1 5 *
|