This product complies with the RoHS Directive (EU 2002/95/EC).
Transistors
2SD1820G
Silicon NPN epitaxial planar type
For general amplification
Complementary to 2SB1219G
■ Features
■ Package
•
• Low collector-emitter saturation voltage VCE(sat)
• S-Mini type package, allowing downsizing of the equipment and
automatic insertion through the tape packing and the magazine
packing.
Code
SMini3-F2
Marking Symbol: X
Pin Name
1: Base
•
•
■ Absolute Maximum Ratings Ta = 25°C
2: Emitter
Parameter
Symbol
Rating
Unit
V
3: Collector
Collector-base voltage (Emitter open) VCBO
Collector-emitter voltage (Base open) VCEO
Emitter-base voltage (Collector open) VEBO
60
50
V
5
V
Collector current
IC
ICP
PC
Tj
500
mA
A
Peak collector current
Collector power dissipation
Junction temperature
Storage temperature
1
150
mW
°C
°C
150
Tstg
−55 to +150
■ Electrical Characteristics Ta = 25°C 3°C
Parameter
Symbol
VCBO
VCEO
VEBO
ICBO
Conditions
Min
60
50
5
Typ
Max
Unit
V
Collector-base voltage (Emitter open)
Collector-emitter voltage (Base open)
Emitter-base voltage (Collector open)
Collector-base cutoff current (Emitter open)
IC = 10 µA, IE = 0
IC = 2 mA, IB = 0
V
IE = 10 µA, IC = 0
V
VCB = 20 V, IE = 0
0.1
µA
1
2
Forward current transfer ratio *
hFE1
hFE2
VCE = 10 V, IC = 150 mA
VCE = 10 V, IC = 500 mA
85
40
340
*
1
Collector-emitter saturation voltage *
VCE(sat) IC = 300 mA, IB = 30 mA
0.35
200
6
0.60
15
V
MHz
pF
1
Transition frequency *
fT
VCB = 10 V, IE = −50 mA, f = 200 MHz
Collector output capacitance
Cob
VCB = 10 V, IE = 0, f = 1 MHz
(Common base, input open circuited)
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.
2. 1: Pulse measurement
*
2: Rank classification
*
Rank
Q
85 to 170
XQ
R
120 to 240
XR
S
170 to 340
XS
No-rank
85 to 340
X
hFE1
Marking symbol
Product of no-rank is not classified and have no marking symbol for rank.
Publication date: May 2007
SJC00373AED
1
This product complies with the RoHS Directive (EU 2002/95/EC).
SMini3-F2
Unit: mm
2.00 0.20
0.30 +−00..0025
3
1
2
0.13 +−00..0025
(0.65)
(0.65)
1.30 0.10
(5°)
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.
|