Peerless Industries Indoor Furnishings SS550P User Manual

Installation and Assembly: 32" - 50" Flat Panel TV Stand  
Models: SS550P, SS550P-S  
This product is UL Listed. It must be  
installed by a qualified professional  
R
installer.  
Max Load Capacity:  
150 lb (68 kg) screen  
50 lb (22.7 kg) per shelf  
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
 
A
C
B
Before you begin, make sure all parts shown are included with your product.  
Parts List  
SS550P  
SS550P-S  
Description  
screen mount bracket  
hook plate  
shelf support  
shelf clamp bracket  
base  
Qty.  
1
1
2
2
1
1
2
1
Black Part # Silver Part#  
H
A
B
C
D
E
F
201-P1156  
201-P1157  
201-P1158  
201-P1159  
201-P1633  
201-P1109  
201-P1513  
580-P1180  
590-1208  
590-1210  
590-1209  
520-2325  
520-2326  
530-1022  
540-9406  
520-9550  
560-9715  
560-9646  
570-0043  
520-9262  
560-9716  
201-4156  
201-4157  
201-4158  
201-4159  
201-4633  
201-4109  
200-4513  
580-4180  
590-1208  
590-4210  
590-1209  
520-1325  
520-1326  
530-2022  
540-9446  
520-9550  
560-9715  
560-9646  
570-0043  
520-9262  
560-9716  
universal plate  
G adapter bracket  
H
I
J
K
L
upright  
glass shelf  
top cover  
button bumper  
1/4-20 x 12mm decorative screw  
2
1
D
E
18  
18  
4
18  
14  
3
1
1
1
4
M 1/4-20 x 20mm decorative screw  
1/4-20mm nut  
O 5/16" flat washer  
3/8-16 x 2.5" socket screw  
Q 7/32" allen wrench  
N
P
R
S
T
4mm allen wrench  
adhesive felt  
M10 x15mm socket screw  
6mm allen wrench  
U
1
F
G
P
I
J
K
L
M
N
O
S
U
T
Q
R
Some parts may appear slightly different than illustrated.  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
3 of 11  
 
Phillips Adapter Bracket Fasteners  
M4 x 12 mm (6)  
504-9013  
M6 x 12 mm (4)  
520-1128  
M5 x 12 mm (4)  
520-1027  
M8 x 16 mm (6)  
520-9257  
M6 x 20 mm (4)  
520-9402  
M5 x 25 mm (4)  
520-9543  
M8 x 25 mm (4)  
520-1031  
M4 x 25 mm (4)  
504-1015  
M6 x 25 mm (4)  
520-1208  
M6 x 30 mm (4)  
510-9109  
multi-washer (6)  
580-1036  
M8 x 40 mm (4)  
520-1136  
I.D. .22" (5.6 mm) (4)  
540-1057  
I.D. .34" (8.7 mm) (4)  
540-1059  
Cut adhesive felt (S) into four pieces as shown in figure 1.1 below and affix to bottom of base (E).  
1
Attach upright (H) to base (E) using three 3/8-16 x 2.5" socket screws (P). Tighten screws using 7/32"  
allen wrench (Q).  
1-1  
Run cords through upright (H) using cord management holes as shown in figure 1.2.  
1-2  
CORD MANAGEMENT HOLE  
H
CORD MANAGEMENT HOLE  
S
H
CORD MANAGEMENT HOLE  
E
P
fig. 1.1  
fig. 1.2  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
4 of 11  
 
Loosely attach four 1/4-20 x 12 mm screws (L),  
washers (O), and 1/4-20 nuts (N) to shelf  
support (C).  
Slide shelf support (C) onto upright (H) so that 1/4-20  
nuts (N) slide into slots of upright (H) as shown in figure  
3 and detail 1. Slide shelf support to desired position,  
level, then tighten 1/4-20 x 12 mm screws (L) using  
4 mm allen wrench (R).  
2
3
NOTE: MAXIMUM OF TWO SHELVES  
Max height of top shelf is 34" from base.  
Max height of second shelf is 28" from base.  
3-1  
N
L
C
O
L
N
C
SLOT  
H
H
DETAIL 1  
fig. 3  
Insert six button bumpers (K) into shelf support (C).  
Place glass shelf (I) on shelf support.  
Insert three button bumpers (K) into bottom of shelf  
clamp bracket (D).  
4
5
Attach shelf clamp bracket (D) to shelf support (C)  
using two 1/4-20 x 20 mm screws (M) and two  
5-1  
1/4-20 nuts (N).  
For second shelf installation, repeat steps 2  
through 5-1.  
5-2  
D
K
I
M
K
C
C
N
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
5 of 11  
 
Loosely attach six 1/4-20 x 12 mm screws (L),  
washers (O), and 1/4-20 nuts (N) to screen mount  
bracket (A).  
Slide screen mount bracket (A) onto upright (H) so that  
1/4-20 nuts (N) slide into slots of upright (H) as shown  
in figure 7 and detail 2. Slide screen mount bracket to  
desired position, level, then tighten 1/4-20 x 12 mm  
screws (L) using 4 mm allen wrench (R).  
6
7
N
A
N
L
SLOT  
H
H
DETAIL 2  
L
A
O
fig. 7  
Snap top cover (J) onto upright (H).  
Insert two 1/4-20 x 12 mm screws (L) into screen  
mount bracket (A), leaving 1/8" of exposed thread as  
shown in figure 9 and detail 3.  
8
9
J
L
1/8"  
A
DETAIL 3  
H
fig. 9  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
6 of 11  
 
Attaching Screen Using Universal Plate withAdapter Brackets  
For attaching screens with VESA 100 hole pattern, skip to page 10.  
Attach universal plate (F) to hook plate (B) using four  
M10 x 15 mm socket screws (T). Tighten screws  
using 6 mm allen wrench (U).  
Attach hook plate (B) to screen mount bracket (A).  
10  
11  
B
F
B
T
A
Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws  
using 4 mm allen wrench (R).  
12  
L
L
L
No Tilt  
2° Backward Tilt  
5° Forward Tilt  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
7 of 11  
 
Installing Adapter Brackets  
WARNING  
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause  
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become  
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.  
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly  
secured, damage may occur to screen or product may fail.  
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen  
13  
face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs, base, cover, or  
screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the adapter brackets to be  
attached. Select the small, medium, large or extra large screws from the baffled fastener pack then attach tilt brackets to  
screen following figure 13.1 or 13.2.  
NOTE: Top and bottom mounting holes must be used for attaching brackets. Verify that all holes are properly aligned, and  
then tighten screws using a phillips screwdriver.  
X
CENTERBRACKETSVERTICALLY  
ON  
G
BACKOFSCREEN  
X
Note: "X" dimensions should be equal.  
Notes:  
MULTI-WASHER  
• The number of fasteners used will vary,  
depending upon the type of screen.  
MEDIUMHOLEFORM5SCREWS  
SMALLHOLEFORM4SCREWS  
LARGEHOLEFORM6SCREWS  
• Multi-washers and spacers may not be  
used, depending upon the type of screen.  
• Use the corresponding hole in the multi-  
washer that matches your screw size as  
shown.  
NOTE: For flat back screens proceed to step 13-1. For bump-out or recessed back screen skip to step 13-2.  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
8 of 11  
 
For Flat Back Screen  
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2  
for a full screen compatibility chart for this mount.  
13-1  
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown  
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.  
If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.  
Repeat for remaining mounting holes, level brackets and tighten screws.  
NOTE: Spacers may not be used, depending upon the type of screen.  
fig. 13.1  
SCREEN  
MULTI-WASHER  
SCREW  
ADAPTER  
BRACKET (G)  
If you have any questions, please call Peerless customer care at 1-800-865-2112.  
For Bump-out or Recessed Back Screen  
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2  
for a full screen compatibility chart for this mount.  
13-2  
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into  
screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place.  
Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the  
baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.  
fig. 13.2  
SCREEN  
MULTI-WASHER  
SPACER  
SCREW  
ADAPTER  
BRACKET (G)  
If you have any questions, please call Peerless customer care at 1-800-865-2112.  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
9 of 11  
 
Mounting and Removing Flat Panel Screen  
WARNING  
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.  
Hook adapter brackets (G) onto universal plate (F), then slowly swing screen in as shown. Turn screws clockwise at  
least six times to prevent screen from being removed as shown in detail 4.  
Note: Tighten using 4 mm allen wrench (R).  
14  
Screen can be adjusted horizontally if desired.  
Note: It is important to lock screen down! To lock the screen down, tighten screws to adapter bracket as shown in  
detail 4.  
To remove screen from mount, loosen screws, swing screen away from mount, and lift screen off of mount.  
F
F
SCREWS  
G
DETAIL 4  
G
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
10 of 11  
 
Attaching Screen with VESA100 Mounting Pattern  
WARNING  
• If screws don't get three complete turns in the screen inserts or if screws bottom out and hook plate is still not tightly  
secured, damage may occur to screen or product may fail.  
Choose hole pattern as shown in figure 10. Attach  
hook plate (B) to back of screen using four M4 x 12  
mm screws. Tighten screws using a phillips screw-  
driver.  
Attach hook plate (B) to screen mount bracket (A).  
10  
11  
B
fig 10  
A
B
M4 X 12 MM SCREWS  
Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws  
using 4 mm allen wrench (R).  
12  
L
L
L
No Tilt  
2° Backward Tilt  
5° Forward Tilt  
ISSUED: 09-05-06 SHEET #: 202-9166-7 11-10-08  
11 of 11  
©2007, PeerlessIndustries, Inc. Allrightsreserved.  
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.  
 

Pentax Digital Camera Optio S5i User Manual
Philips Coffeemaker HD7001 User Manual
Philips Stereo Amplifier BGY280 User Manual
Philips TV Cables SWA2105W User Manual
Philips Universal Remote pmdvd6 User Manual
Pioneer Car Video System S HTD1 User Manual
Pioneer CD Player DEH P250 User Manual
Planet Technology Network Card WPG 110 User Manual
Polar Heart Rate Monitor S610i User Manual
ProForm Treadmill PFTL721040 User Manual