Polycom Server KWS600v3 User Manual

Part No. 14168600, Ed.2  
April 3, 2008  
®
Polycom KWS600v3 Configuration Guide  
(SIP Protocol)  
 
Contents  
3
Contents  
Chapter 1 Preface.......................................................................................................... 5  
1.1 Before You Begin........................................................................................................ 5  
1.2 Chapter Overview....................................................................................................... 5  
1.3 Related Documentation.............................................................................................. 5  
Chapter 2 SIP Specific Configuration ......................................................................... 7  
2.1 Configuring DECT Master .......................................................................................... 7  
2.2 Configuring DECT System ......................................................................................... 8  
2.3 Configuring Call Waiting ............................................................................................. 8  
KWS600v3 Protocol Configuration Guide (SIP Protocol)  
 
4
14168600, Ed.2  
 
5
Chapter 1 Preface  
This guide describes the specific configuration of a KIRK Wireless Server 600v3  
(KWS600v3) when using SIP Protocol. The guide is intended for qualified technicians  
who will install, register and configure a KWS600v3 in a SIP environment. To qualify to  
install the KWS600v3 Solution, you must have successfully completed the KWS600v3  
technical training.  
The user guide also provides you with information about:  
KIRK Wireless Server 600v3  
Web based Adminstration Page of the KIRK Wireless Server 600v3  
1.1 Before You Begin  
This guide assumes the following:  
that users have a working knowledge of the call handlers operation  
that the call handler is installed and initialized and is working correctly  
that users have a working knowledge of the KIRK Wireless Server 600v3  
that users have a working knowledge of the web based Administration Page  
that users are familiar with the KIRK Wireless Server 600v3 Installation and  
Configuration Guide  
1.2 Chapter Overview  
Where is it?  
What is it about?  
When to use it?  
Chapter 2  
SIP Specific Configuration  
To learn how to configure a KWS600v3 in a SIP  
environment.  
1
1.3 Related Documentation  
For further information about the system components not covered by this manual, refer  
to the following documentation:  
Subject  
Documentation  
KIRK Wireless Server 600v3  
Installation and Configuration Guide  
KWS600v3 Configuration Guide (SIP Protocol)  
 
6
Preface  
14168600, Ed.2  
 
7
Chapter 2 SIP Specific Configuration  
This section describes how to configure the KIRK Wireless Server 600v3 when using SIP  
Protocol. It only describes specific configuration procedures in connection with the SIP  
Protocol.  
For detailed information about installing and configuring the KWS600v3 in general, refer  
to the KIRK Wireless Server 600v3 Installation and Configuration Guide.  
For information about accessing the web based Administration Page of the KIRK  
Wireless Server 600v3, refer to the KIRK Wireless Server 600v3 Installation and  
Configuration Guide.  
This section contains information about:  
“Configuring DECT Master” on page 7  
“Configuring DECT System” on page 8  
“Configuring Call Waiting” on page 8  
2.1 Configuring DECT Master  
When configuring the KWS600v3 in a SIP environment it is necessary to type a  
gatekeeper ID.  
1
Under the Configuration menu, click DECT, and then click Master.  
Figure 1 Adm. Page: Configuration/DECT/Master page - SIP Protocol  
2
In the GK-Id field, type a domain name.  
An example of a domain name could be: sip:kirk323.kirktelecom.com.net:5060.  
Contact your system administrator for more information.  
Click OK.  
3
4
Click Reset (under Administration menu) to save your configuration.  
KWS600v3  
 
8
SIP Specific Configuration  
2.2 Configuring DECT System  
When configuring the KWS600v3 in a SIP environment it is necessary to enable the check  
boxes; Enbloc Dialing and DTMF through RTP channel.  
1
Under the Configuration menu, click DECT, and then click System.  
Figure 2 Adm. Page: Configuration/DECT/System page - SIP Protocol  
2
3
Select the Enbloc Dialing check box.  
The Enbloc Dialing check box has to be enabled in a SIP configuration in order for  
the handset to collect all digits, before passing them on to a call handler for routing.  
Select the DTMF check box.  
The DTMF check box has to be enabled in a SIP configuration if DTMF tones are  
needed (optional).  
4
5
Click OK.  
Click Reset (under Administration menu) to save your configuration.  
2.3 Configuring Call Waiting  
To enable the Call Waiting feature in the system, you must do the following:  
14168600, Ed.2  
 
SIP Specific Configuration  
9
1
Under the Configuration menu, click DECT, and then click Features.  
Figure 3 Adm. Page: Configuration/DECT/Features page - SIP Protocol  
2
3
4
Select the Enable check box to enable the Call Waiting feature.  
Click OK.  
Click reset required.  
A window appear.  
Click OK.  
5
The Call Waiting feature is now enabled in the system. For the feature to be used, it  
must be activated on each handset by pressing *43# on the handset.  
KWS600v3 Protocol Configuration Guide (SIP Protocol)  
 
10  
SIP Specific Configuration  
14168600, Ed.2  
 

Pentair Swimming Pool Heater CH User Manual
Perreaux Stereo Amplifier 6160 P User Manual
Philips DVR VR 540 User Manual
Philips Iron GC650 User Manual
Philips Speaker SPA3300 User Manual
Philips Washer Dryer PSC805 User Manual
Pico Communications Power Supply PICOPSU 90 User Manual
Pioneer DVD Player DV 588A S User Manual
Planar Car Video System PLL2410W User Manual
Precor Bicycle Accessories C846 User Manual