HS-615 HANGING SPEAKER
O w n e r s M a n u a l
Features (continued)
the -3 position decreases the output of the tweeter relative to the woofer. The
0 position is the factory setting and generally provides the most natural response
from the speaker.
The use of a 70 Volt transformer allows several HS-615 speakers to be used together
by running a speaker wire from one speaker to the next in a parallel connection
when using a 70 Volt amplifier (as shown in the wiring diagram below).
WARNING: Refer to the wiring diagrams and voltage selector sections to
properly install a 70 Volt system.
Wiring Diagrams
CAUTION: If your amplifier isn’t capable of handling the impedance of all
connected speakers, this may result in overloading the amplifier and may cause
possible damage to the amplifier. Check your amplifier’s documentation for
proper impedance levels.
Parallel Connection
A parallel connection exists when speakers are connected directly to an amplifier
(as shown in the illustration below). Each speaker’s positive terminal is directly
connected to the amplifier’s positive terminal, and each negative terminal is
directly connected to the amplifier’s negative terminal. This type of connection
should be made when using a 70 Volt amplifier.
In this example, each speaker is set to
70 Volt operation and is being powered
by a 70 Volt amplifier. If the speakers
were set to 8 Ohm operation, the total
impedance (using Ohm’s Law) equals
(8 x 8) ÷ (8 + 8) or 4 Ohms, which
may be too low for some amplifiers.
Make sure to properly select 70 Volt
or 8 Ohm operation before connecting
the speakers to the amplifier.
2
Wiring Diagrams (continued)
Series Connection
A series connection exists when two or more speakers are connected together by
one wire. Typically, the negative connection of one speaker is connected to the
positive connection of the next speaker as shown in the illustration below. This
type of connection is reserved for certain 8 Ohm systems ONLY, and NOT FOR 70
VOLT OPERATION. Series connections should only be done with identical speakers
to avoid inconsistencies in sound quality.
In this example, each speaker has a impedance of 8 Ohms. In a series connection as
shown here, the total impedance equals 8+8 or 16 Ohms. The total impedance of a
series connection is the sum of each speaker’s impedance.
Voltage Selector
As previously mentioned, the HS-615 can be used in a 70
Volt system or in an 8 Ohm system. The voltage
selector switch allows you to properly set the
speaker to 8 Ohm or 70 Volt operation.
The wattage selector switch allows
the choice of 2, 4, 8 or 16 watt taps
for 70 Volt operation. For 70 Volt
operation, be sure to correctly
set the wattage selector
switch so that the number
of speakers multiplied by
the wattage setting does
not exceed the power
output of the amplifier.
3
Safety Compliance
CE LOGO: These products are in compliance with the EMC Directive 89/336/EEC and
Article 10 (1) of the directive. In compliance with Technical Regulations EN55013-1
and EN50082-1.
Specifications
8 Ohm Operation
2-way Hanging Speaker
Speaker Type:
(20-foot Hanging Cable Included)
100Hz–20kHz 3dB
87dB (2.83V @ 1 Meter)
2–50 Watts / 70 Volts
(1) 6½” (165mm) Polygraphite Cone
(1) 1” (25mm) Swivel Silk Dome
3,000 Hz
Frequency Response:
Sensitivity:
Recommended/Power Rating:
Woofer:
Tweeter:
Crossover Frequency:
Filter Slope:
12dB/octave
8 Ohms
Impedance:
9½” Dia. x 5” H
Finished Dimensions:
(241mm Dia. x 127mm H)
5 lbs. (2.27 Kg)
Weight:
70 Volt Operation
70 Volt Taps:
2, 4, 8, and 16 Watts
4
Troubleshooting
Situation:
Probable Cause:
Solution:
No sound from speakers
Speaker wire not
connected
Make sure wire is
connected at both the
speaker and the amplifier
observing proper polarity
Speaker selector on
amplifier is not on
Activate proper selector
on amplifier
No sound from speaker
Balance control on
receiver or pre-amp is
not centered
Place balance control in
the center
Speaker wire not securely Check all connections at
connected
amplifier and speakers
Very little bass and/or
imaging
Speakers are wired out
of phase
Check entire system
for proper polarity and
make adjustments as
necessary
Warranty
Your RBH Sound residential/commercial 70 volt compatible hanging speaker is
covered by a limited warranty against defects in materials and workmanship for
a period of (5) five years from the original date of purchase. This warranty is
provided by the authorized RBH Sound dealer where the speaker was purchased.
Warranty repair will be performed only when your purchase receipt is presented
as proof of ownership and date of purchase. Defective parts will be repaired or
replaced without charge by your dealer’s store or the location designated by your
dealer authorized to service RBH Sound products. Charges for unauthorized service
and transportation cost are not reimbursable under this warranty. This warranty
becomes void if the product has been damaged by alteration, misuse or neglect.
RBH Sound assumes no liability for property damage or any other incidental or
consequential damage whatsoever which may result from the failure of this product.
Any and all warranties of merchantability and fitness implied by law are limited to
the duration of this express warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitations may not apply to you.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
5
Redefining the Way You Experience Sound.TM
382 Marshall Way, Layton, Utah • USA • 84041
Toll Free: (800) 543-2205 • Fax: (801) 543-3300
It is RBH Sound policy to continuously incorporate improvements into our products; all specifications are subject to change without notice.
Copyright © 2008 RBH Sound. All Rights Reserved.
|