INSTALLATION INSTRUCTIONS
HB0058
WP29M SERIES
!
!
INTENDED FOR DOMESTIC COOKING ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE, CARE AND OPERATION INFORMATION
ON PAGES 10 AND 11.
SV07693 rev. G
- WP29M SERIES RANGE HOOD SYSTEM -
INTERIOR BLOWERS
Model 441
Model 647
Model 634 or 644
(roof cap)
Model 437
(High capacity roof cap)
(10’’ Round wall cap)
(7” Round wall cap)
Model 418
(10” round adjustable elbow)
Model 415
(7” round adjustable elbow)
Model 421
(10” Round Vertical
In-line damper —
Optional)
Model 407
(7” round duct—2 ft. sections)
Model 410
(10” round duct—2 ft. sections)
Model 427
(4½” x 18½”
to 10” Round,
6” high - lateral
Model 423
(4½” x 18½”
to 10” Round -
vertical
Model 424
(4½” x 18½”
to 10” Round - to 10” Round -
horiz. front/rear
Model 454
(4½” x 18½”
Model 453
(4½” x 18½”
to 10” Round -
horiz. /left
horiz. /right
OPTIONAL
DECORATIVE FLUE
AEWP SERIES
NON-DUCT KIT FLUE
ANKWP SERIES
OPTIONAL
FLAT TOP COVER
ADPWP SERIES
WP29M
MODEL P6
SERIES HOOD
(Canopy with
blower controls
& lighting.
BLOWER/ROUGH-IN KIT
(600 cfm interior blower &
rough-in plate)
Required for all
installations.)
MODEL P12
BLOWER/ROUGH-IN KIT
(1200 cfm interior blower
& rough-in plate)
HL0081
NOTE: For a non-ducted installation, we
recommend the non-duct kit flue
ANKWP Series be installed with
Model P6 Blower/Rough-in kit for
effectiveness.
- 3 -
- WP29M SERIES RANGE HOOD SYSTEM -
IN-LINE AND EXTERIOR BLOWERS
Model 441
Model 437
(High capacity roof cap)
Model ILB9 (800 cfm)
or ILB11 (1100 cfm)
in-line blower
(includes two 8” x 12” to
10’’ round transitions)
(10” Round wall cap)
Model EB12 (1200 cfm)
or EB15 (1500 cfm)
exterior blower
Model EB6 (600 cfm)
or EB9(900 cfm)
exterior blower
Model 441
(10” Round
wall cap)
Model 643
(8” Round
wall cap)
Model ILB6 (600 cfm)
in-line blower
(includes two 4½” x 18½”
to 10’’ round transitions)
Model 421
Model 418
10” Round
adjustable elbow
(optional)
(10” Round vert.
in-line damper)
Recommended
for use with
Model ILB3 (280 cfm)
in-line blower
(includes one 8” to 10”
round transition)
exterior blowers
Model 410
(10” Round duct
—2ft. sections)
OPTIONAL
DECORATIVE FLUE
AEWP SERIES
WP29M
SERIES HOOD
(Canopy with
blower controls
& lighting.
OPTIONAL
FLAT TOP COVER
ADPWP SERIES
required for all
installations.)
In-line and exterior blower rough-in kit
(included with EB6, EB9, EB12, EB15,
ILB3, ILB6, ILB9 and ILB11 blowers.)
HL0082
- 4 -
1. SELECT BLOWER OPTION AND INSTALLATION TYPE
1.1 NON-DUCTED INSTALLATION
For a non-ducted installation, we recommend using interior blower Best model P6 for effectiveness. (Blower sold separately.)
The non-duct kit ANKWP Series (sold separately) must be installed. This kit fits hood from 30-inch width up to 48-inch
width. See installation instructions included with the non-duct kit ANKWP Series.
1.2 DUCTED INSTALLATION
For a ducted installation, either an interior or exterior blower or in-line blower may be used with this hood. The Best WP29M
Series must be installed with blower models P6, P12, ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only.
Other blowers cannot be substituted. (Blowers sold separately.)
Plan where and how the ductwork will be installed.
If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 8, 11, 12, 14
and up of this manual.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use metal duct tape to
seal duct joints.
ROOF CAP
ROOF
CAP
7" (178 mm)
ROUND DUCT
10" (254 mm)
ROUND DUCT
DECORATIVE
FLUE
DECORATIVE
6" or 12"
or SOFFIT (152 mm
FLUE or SOFFIT
6" or 12"
(152 mm
WALL
CAP
WALL CAP
or 305 mm)
or 305 mm)
HOOD
ROUND
HOOD
7" (178 mm)
ROUND
ELBOW
TRANSITION
4½" x 18½" to 10"
(114 mm x 470 mm
to 254 mm)
(see page 3)
24" TO 30" (609 mm to 762 mm)
ABOVE COOKING SURFACE
24" to 30" (609 mm to 762 mm)
ABOVE COOKING SURFACE
HH0069A
HH0068A
MODEL P6 SINGLE INTERIOR BLOWER
TYPICAL DUCTWORK
MODEL P12 DUAL INTERIOR BLOWER
TYPICAL DUCTWORK
EXTERIOR BLOWER
ROOF CAP
10" (254 mm)
ROUND DUCT
10” ROUND DUCT
IN-LINE BLOWER
DECORATIVE FLUE
or SOFFIT
10" (254 mm)
ROUND ELBOW
6" or 12"
(152 mm
or 305 mm)
EXTERIOR
BLOWER
WALL
CAP
HOOD
HOOD
24” to 30”
(609 to 762 mm)
ABOVE
COOKING SURFACE
24" to 30" (609 mm to 762 mm)
ABOVE COOKING SURFACE
HH0071A
HH0070A
MODEL EB6, EB9, EB12 OR EB15
MODEL ILB3, ILB6, ILB9 OR ILB11
EXTERIOR BLOWER TYPICAL DUCTWORK
IN-LINE BLOWER TYPICAL DUCTWORK
- 5 -
2. MEASURE INSTALLATION
Dimensions for the most common installation are shown beside.
The minimum hood distance above cooktop must not be less
than 24’’. A maximum of 30” above cooktop is highly
recommended for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
Ceiling
Top of wood
mounting strip
A + 0.25’’ (6 mm)
Cabinet, soffit,
decorative flue or
non-duct kit flue
A
Hood
Minimum distance between
the hood and cooktop:
24’’ (610 mm)
Recommended maximum
distance between the hood
and cooktop: 30’’ (762 mm)
Standard 36” (914 mm)
HH0072A
high cooktop
MINIMUM AND MAXIMUM DISTANCE
OVER COOKTOP
3. PREPARE THE INSTALLATION
!
WARNING
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and
gloves.
Remove the installation kit from inside the hood.
Make sure that the following items are included:
- Wood strip (screwed on back of hood)
- Installation manual
- Accessories including:
• Evolution™ hybrid baffle filters (3 for hoods up to 54” width, 4 for 60” width)
• Shielded halogen lights (GU10 type base, 120 V, 50 W) (4 for hoods up to 42” width, 6 for hoods from 48” to 60” width)
• Bag of parts including:
(4) flat head screws no. 10-2”, (8) screws no. 8 x 3/4”, (4) nuts no. 10-32, (2) wall anchors, (2) washers 3/16” ID x 3/4” OD
Parts sold separately:
- Interior blower Model P6 (includes rough-in kit), for either ducted or non-ducted installation.
- Interior blower Model P12 (includes rough-in kit), for ducted installation only.
- In-line blower assembly ILB3, ILB6, ILB9 or ILB11 (all include transition and rough-in plate), for ducted installation only.
- Exterior blower assembly EB6, EB9, EB12 or EB15 (all include rough-in plate), for ducted installation only.
- Transitions, duct, elbows, dampers, wall and roof caps. Refer to pages 3 and 4 for a complete list of venting options and model
numbers.
- Non-duct kit ANKWPD Series, mandatory for non-ducted installation.
- Optional decorative flue AEWP Series, for ducted installation only.
- Optional flat top cover ADPWP Series, for ducting through back of hood, intalled on hood or installed on the optional decorative
flue AEWP Series. Can also be installed on the non-duct kit flue ANKWPD Series.
- 6 -
4. REMOVE THE FILTERS AND THE GREASE DRIP RAIL(S)
1
A. Remove tape on filters.
Remove filters from hood and set aside.
NOTE: It is recommended to start with the
central one.
B. Remove tape on grease drip rail (1).
Lift out grease drip rail and set aside.
NOTE: The 60-inch width hood has 2 grease
drip rails.
HD0175
5. REMOVE THE PAN
Using a Phillips no. 2 or Robertson no. 2 screwdriver, remove the screws retaining the
pan (shaded part on illustration beside) to the hood. Remove the pan and set aside.
RETAINING SCREWS LOCATION
HD0176
6. INSTALL WOOD MOUNTING STRIP
Measure and mark a level line on wall above cooktop location for the wood
mounting strip (see illustration beside and under step 2). Remove wood mounting
strip from back of hood.
Use no. 10 - 2’’ flat head screws to secure the mounting strip to the drywall. Make
sure to hit the wall studs.
CAUTION
Due to the weight of this hood, ensure that the wood strip is attached
to all of the available studs (2 studs minimum for a 30’’ width hood,
more as hood width increases); not into the drywall alone.
HD0174A
1. Drywall
2. Wood mounting strip
3. Flat head screw
4. Wall anchor location
5. Back of hood outline
6. Wall studs
7. INSTALL THE FLUE AND/OR THE FLAT TOP COVER
7.1 DUCTED INSTALLATION: A) OPTIONAL DECORATIVE FLUE AEWP SERIES
For a ducted installation, refer to the instructions sheet included with the optional decorative flue.
B) OPTIONAL FLAT TOP COVER ADPWP SERIES
For ducting through back of hood only, install on hood or on the Optional Decorative Flue AEWP Series.
Refer to the instructions sheet included with the optional flat top cover.
7.2 NON-DUCTED INSTALLATION: NON-DUCT KIT FLUE ANKWP SERIES
Refer to the installation sheet included with the non-duct kit for details.
NOTE:
The Optional Flat Top Cover ADPWP Series can be installed on the Non-Duct Kit Flue ANKWP Series. Refer
to the instructions included with the optional flat top cover.
- 7 -
8. INSTALL THE HOOD
Rest the top back cavity of the hood on the wood mounting strip.
CAUTION
Hold the hood until it is completely secured to the wood mounting
strip.
TOP OF HOOD (INSIDE VIEW)
MOUNTING SCREWS LOCATION
Secure the hood to wood mounting strip with (4) screws no. 8 x 3/4” (for 30” and 36”
width hoods) or (6) screws (for 42” width and wider hoods) provided at locations
shown. Drill (2) 3/16’’ size holes into the drywall for wall anchors through the
existing holes in the inside hood back in the locations shown. Then, install the two
wall anchors with the remaining no. 8 x 3/4” screws and the (2) washers provided.
BACK OF HOOD (INSIDE VIEW)
WALL ANCHORS LOCATION
For a non-ducted installation, go to step 11, Install the Rough-in Plate.
HD0178
9. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR, DUCTED INSTALLATION)
INTERIOR BLOWER: Follow all subsequent steps of this manual.
EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 11 and up of the present manual.
10.INSTALL TRANSITION TO ROUGH-IN PLATE (INTERIOR BLOWER, DUCTED INSTAL.)
Model 423, 424, 427 453, or 454
Attach transition (if required) to blower rough-in plate.
Use metal duct tape to make all joints secure and air-tight.
NOTE: Model P6 blower plate connects directly to 7’’ round ductwork without
a transition.
HO0086
11.INSTALL THE ROUGH-IN PLATE TO THE HOOD (ALL INSTALLATIONS)
11.1 ALL INSTALLATIONS:
Run power cable to installation location. Refer to the instructions included
with the selected blower/rough-in kit (sold separately) for details on
installing the rough-in plate. Install the rough-in plate so that the wiring
box is located on the right side as you are facing the hood.
11.2 DUCTED INSTALLATIONS ONLY:
WIRING COVER
ROUGH-IN PLATE
ON TOP OF HOOD
LOCKNUTS
For ducting through back of hood, remove existing plate from inside back
of hood and attach it to inside top of hood to cover hole. Secure to threaded
studs with same (4) nuts.
LOCKNUTS
PLATE ON BACK OF HOOD
For ducting through top of hood, existing plate remains in place on inside
back of hood.
HD0179
Connect ducting to transition or rough-in plate as you are installing the
rough-in plate. Use duct tape to make all joints secure and air-tight.
12.CONNECT THE WIRING (ALL INSTALLATIONS)
WARNING
!
Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all
applicable codes and standards. Before connecting wires, switch power off at service panel and lock
service disconnecting means to prevent power to be switched on accidentally.
Remove wiring cover from rough-in plate and set aside.
Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw.
Reinstall wiring cover.
- 8 -
13.INSTALL THE BLOWER (INTERIOR OR EXTERIOR BLOWER)
Refer to instructions included with blower.
Once the blower is installed, plug the blower cord (A) into the female receptacle
and the power supply cord (B) onto the male connector inside the hood.
A
B
WARNING
!
Do not plug the two cords into each other.
HE0078
14.REINSTALL THE PAN
Using a Phillips no. 2 or Robertson no. 2 screwdriver and the retaining screws,
reinstall the pan (previously removed in step 6) inside the hood (shaded part on
illustration beside).
RETAINING SCREWS LOCATION
HD0176
15.REINSTALL GREASE DRIP RAIL(S) AND BAFFLE FILTERS
Reinstall grease drip rail(s) (1). The illustration beside shows how to reinsert the
grease drip rail(s) into the range hood.
1
HD0181
CAUTION
Remove protective plastic film covering Evolution™ hybrid baffle filters before installing them.
Before reinstalling Evolution™ hybrid baffle filters, slide out the secondary micromesh filters from their back and remove all
protective plastic film.
15.1 DUCTED INSTALLATION:
Slide in the secondary filters into each baffle filters before reinstalling them on the hood.
15.2 NON-DUCTED INSTALLATION:
Discard the secondary filters. Slide in the charcoal filters included in the non-duct kit. Reinstall the filters on the hood.
1
2
It is recommended to install side filters first and finish with
center one(s).
1.
Insert one end of Evolution™ hybrid baffle filter into
the upper channel of the hood.
2.
Raise the other end toward the inside of hood and insert
in the grease drip rail of the hood.
Replacement filters are available from your dealer. See label
inside hood for size and part number.
HD0180
For charcoal filter replacement kit, see table on page 12.
- 9 -
16.LIGHT BULBS REPLACEMENT
WARNING
!
In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures.
This hood must use 120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base, shielded halogen lamps (included).
WARNING
!
In order to prevent the risk of personal injury, the halogen lamps must be cooled down before removing them.
1
2
3
1. To remove lamps, gently push upwards and turn counterclockwise
to disengage bulb leads from their grooves.
NOTE: If need be, use a rubber dishwashing glove to add grip
when removing the bulb.
2. Install the new lamps by placing the bulb leads into their
grooves in the socket.
3. Gently push upwards and turn clockwise until secure.
HO0089
17.USE AND CARE
Evolution™ Hybrid Baffle Filters
The Evolution™ hybrid baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your
cooking style generates greater grease—like frying foods or wok cooking.
Remove Evolution™ hybrid baffle filters by pushing them towards the back of hood and rotating filters downward. Slide out the
secondary micromesh filter from the back of each hybrid baffle filter before cleaning. Baffle filters are dishwasher safe. Clean
secondary filters with a warm detergent solution. Allow filters to dry completely before reinstalling them in the hood.
Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate
detergent or as a result of local water conditions—but this will not affect filter performance. This discoloration is not covered by
the warranty.
CAUTION
Never attempt to wash the carbon filters in the non-duct kit. Those filters must be replaced by new ones.
Refer to the non-duct kit installation instructions for details.
Grease Drip Rail
The grease drip rail should be cleaned frequently. Lift it out from the hood and use a warm detergent solution. As for the baffle
filters, wash more often if your cooking style generates greater grease—like frying foods or wok cooking. Allow grease drip rail
to dry completely before reinstalling it in the hood.
Blower Cleaning
Remove the filters in order to access the blower. Vacuum blower to clean. Do not immerse in water. Refer to blower instruction
manual for more details.
Hood Cleaning
Stainless steel cleaning: How to maintain its “BRIGHT LOOK”
Do:
Don’t:
• Regularly wash with clean cloth or rag soaked with warm • Use any steel or stainless steel wool or any other scrapers
water and mild soap or liquid dish detergent.
to remove stubborn dirt.
• Always clean in the direction of original polish lines.
• Use any harsh or abrasive cleansers.
• Always rinse well with clear water (2 or 3 times) after • Allow dirt to accumulate.
cleaning. Wipe dry completely.
• You may also use a specialized household stainless
steel cleaner.
• Let plaster dust or any other construction residues reach
the hood. During construction or renovation, cover the
hood to make sure no dust sticks to stainless steel surface.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel.
• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should
never be used close to a range.
- 10 -
18.OPERATION
Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run for a few
minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
2
1
3
4
HC0030
1. ON/OFF Blower switch
2. Blower speed control
3. ON/OFF Halogen light switch
4. Light intensity control
Blower
The blower is operated using two (2) controls.
Use the ON/OFF switch (item 1 on picture above) to start and stop the blower. When turned on, the blower will operate at the
previous setting of the speed control (item 2 on picture above).
Turn the speed control knob counterclockwise to increase blower speed—clockwise to decrease speed.
HEAT SENTRY™
This hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will speed up the blower if it senses
excessive heat above the cooking surface.
If blower is ON at a lower speed setting—it turns the blower up to HIGH speed.
When the temperature level drops to normal, the blower will return to its original setting.
Cooktop Lighting (Halogen)
The halogen lighting is controlled by two switches; one ON/OFF switch (item 3 on picture above) and one light intensity control switch.
When turned on, the halogen bulbs will light cooktop at the previous setting of the light intensity control (item 4 on picture above).
Turn the light intensity control knob counterclockwise to increase lighting—clockwise to decrease lighting.
Use 120 V, 50 W, MR16 or PAR16 with GU10 base, shielded halogen lamps (included).
WARRANTY
ONE-YEAR LIMITED WARRANTY FOR BEST PRODUCTS
Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will
be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR
MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which
is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT
BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This
warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to
misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation
contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states
or provinces do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH PRODUCT USE OR PERFORMANCE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province
to another. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number
stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or
part. At the time of requesting warranty service, you must present evidence of the original purchase date.
®
In USA - Best , 926 W. State Street, Hartford, WI 53027 (800-558-1711)
®
In Canada - Best , 550 Lemire Blvd., Drummondville, QC, Canada, J2C 7W9 (866-737-7770)
- 11 -
SERVICE PARTS
7
4
8
3
1
2
5
6
11
12
10
9
14
13
WP29XX4 MODEL
KEY
PART
QTY. (HOOD WIDTH)
30’’ 36’’ 42’’ 48’’ 54’’ 60’’
NO. NUMBER DESCRIPTION
1
2
3
4
5
6
7
8
SV16569 LAMP SHELL, SOCKET AND TRIM ASS’Y
SV05921 SHIELDED HALOGEN BULBS (50 W, 120 V, PAR16, GU-10)
SV03501 ROTARY CONTROL
SV07689 TOGGLE SWITCH
SV16966 PLASTIC CONTROL FRAME AND KNOB ASS’Y
SV07688 KNOB
SV13924 MALE CONNECTOR
SV13923 FEMALE CONNECTOR
SV16793 GREASE DRIP RAIL 30”
SV16794 GREASE DRIP RAIL 36”
SV16796 GREASE DRIP RAIL 48”
4
4
2
2
1
2
1
1
1
-
4
4
2
2
1
2
1
1
-
1
-
1
-
1
-
-
-
-
3
2
1
2
1
1
4
4
2
2
1
2
1
1
-
1
-
1
-
-
1
-
-
-
3
2
1
2
1
1
6
6
2
2
1
2
1
1
-
6
6
2
2
1
2
1
1
-
6
6
2
2
1
2
1
1
2
-
-
1
-
-
-
9
-
-
-
1
1
-
-
-
1
-
-
3
-
3
-
1
1
-
-
-
-
1
-
3
-
3
-
10 SV03435 THERMISTOR HEAT SENTRY™
1
1
-
-
-
-
-
3
3
-
3
-
SV17115 INSIDE FRAME ASS’Y (30” X 24” X 18”) (INCLUDING ITEM 12)
SV17116 INSIDE FRAME ASS’Y (36” X 24” X 18”) (INCLUDING ITEM 12)
SV17117 INSIDE FRAME ASS’Y (42” X 24” X 18”) (INCLUDING ITEM 12)
11
SV17118 INSIDE FRAME ASS’Y (48” X 24” X 18”) (INCLUDING ITEM 12)
SV17119 INSIDE FRAME ASS’Y (54” X 24” X 18”) (INCLUDING ITEM 12)
SV17120 INSIDE FRAME ASS’Y (60” X 24” X 18”) (INCLUDING ITEM 12)
12 SV05528 FILTER SPRING CLIP
-
-
1
6
6
-
6
-
SV07694 SECONDARY MICROMESH FILTER 8.84” X 8.50”
SV07695 SECONDARY MICROMESH FILTER 14.84” X 8.50”
SV16967 EVOLUTION™ HYBRID BAFFLE FILTER 8.95” X 8.61” X 1” (INCL. ITEM 13)
SV16968 EVOLUTION™ HYBRID BAFFLE FILTER 14.95” X 8.61” X 1” (INCL. ITEM 13)
SV07693 INSTALLATION GUIDE
PARTS BAG (FLAT HEAD SCREW NO. 10 X 2’’ [4],
SV12971 SCREWS NO. 8 X 3/4’’ [8], NUTS NO. 10-32 [4],
WALL ANCHORS [2], WASHERS 3/16’’ ID X 3/4’’ OD)
SV05869 BEST LOGO
SV16998 CHARCOAL FILTER KIT (INCLUDING 3 CHARCOAL FILTERS)
SV16999 CHARCOAL FILTER KIT (INCLUDING 3 CHARCOAL FILTERS)
SV17000 CHARCOAL FILTER KIT (INCLUDING 3 CHARCOAL FILTERS)
13
14
3
1
3
1
*
*
1
1
1
1
1
1
1
1
1
*
*
*
*
1
1
-
1
-
1
-
1
-
1
-
1
-
-
1
N/A N/A
N/A N/A
N/A N/A
-
1
*
NOT SHOWN.
WP29XX7 MODEL
SAME PART NUMBERS, EXCEPT FOR ITEM 11 (SEE BELOW)
KEY
PART
QTY. (HOOD WIDTH)
36’’ 42’’ 48’’ 54’’ 60’’
NO. NUMBER DESCRIPTION
SV17121 INSIDE FRAME ASS’Y (36” X 27” X 18”) (INCLUDING ITEM 12)
SV17122 INSIDE FRAME ASS’Y (42” X 27” X 18”) (INCLUDING ITEM 12)
11 SV17123 INSIDE FRAME ASS’Y (48” X 27” X 18”) (INCLUDING ITEM 12)
SV17124 INSIDE FRAME ASS’Y (54” X 27” X 18”) (INCLUDING ITEM 12)
SV17125 INSIDE FRAME ASS’Y (60” X 27” X 18”) (INCLUDING ITEM 12)
1
-
-
-
-
-
1
-
-
-
-
-
1
-
-
-
-
1
-
-
-
-
-
1
-
- 12 -
|