Microflex R_200_400_IB 8/24/06 2:34 PM Page 1
®
®
MC
400
Use and
Care Guide
R-200
R-225
R-400 (shown)
Microflex R_200_400_IB 8/24/06 2:34 PM Page 4
Product Features
Congratulations on your purchase of a premium
Shaver Parts
®
Remington shaver, with revolutionary shaving technology
(A)
Which model is yours?
Corded Cordless
Operation Operation
Run
Time
Charge
Time
Locking
Trimmer
Pouch
X
X
X
R-200
R-225
R-400
Easy-View® Trimmer
X
X
30 min.
16 hrs.
X
(B)
(D)
Power Sytem
Indicator Lights
(R-400 only)
■ Corded (R-200 & R-225)
shavers can only be used
with the power cord.
Charging
■ The charging indicator is a
green light that glows when
the shaver is being charged.
(C)
(H)
■ Cordless (R-400) shavers can
only be used without the
power cord.
(A) Head & cutter assembly
(B) ON/OFF button
(C) Power port
(D) Trimmer button
(E) Head guard
(F) Cleaning brush
(G) Storage pouch (Model R-225 & R-400)
(H) Power cord
(E)
(G)
(F)
4
5
Microflex R_200_400_IB 8/24/06 2:34 PM Page 6
How to Use
Usage Tips
Before using read the important safety
instruction section in front of the manual.
■ Your shaver cannot be overcharged,
so you can leave it plugged in and
charging between shaves.
shave and minimum wear. Avoid
Getting a close, comfortable
shave
holding the shaver at an angle so
only one head touches the skin. This
could cause skin irritation.
Remington shavers need no adjust-
ments to their heads or cutters before
you shave. The heads will automatically
adjust to the contours of your face.
Removing the Headguard
Before operating your shaver, remove
the headguard, which protects the
head and cutter assembly. It is
important to remove the headguard
correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the head
guard.
2. Lift the lower rear edge.
3. Pull the headguard away from the
shaver.
! Always keep the protective head
guard on the shaver head and keep
the trimmer in the OFF position when
the shaver is not in use.
■ To preserve the life of the batteries,
allow them to fully discharge every
six months, then recharge them for
24 hours.
Rechargeable shavers like the R-400
are designed for cordless operation
only. Plugging it in will not provide the
power to shave.
■ Use short, circular
strokes. Use your free
hand to stretch your
skin. This encourages
Adjusting to your new shaver
your whiskers to stand
As with every shaver, your shave will
improve over time. So allow about three
weeks to develop an effective shaving
style and for your beard to adjust to the
new shaver. The adaptation period may
take a little longer if your skin is sensi-
tive, or if you alternate between shaving
methods.
out, making it easier for them
to enter the cutting chamber.
■ It is not necessary to apply pressure
while shaving, just let the shaver
glide lightly on your skin. Never
press hard. Pressing only flattens
your whiskers, which makes it
harder for them to enter the cutting
chamber. It will also wear out the
cutting surface more quickly. A gentle
touch makes shaving easier and
helps avoid possible skin irritation.
Cordless Operation of the R-400
■ Remove the AC power cord from the
electrical outlet, then remove from
shaver’s power port.
■To activate the shaver, slide the
power button up to the ON position.
Before you begin:
■Wait at least 15
minutes after getting
12
®
Operating the Easy-View
Corded Operation of the
R-200 and R-225
9
3
up before shaving to
ensure the face is free
of puffiness that may
be present from sleeping.
■ Make sure your face
is clean and dry before
starting.
Trimmer
6
The Easy-View®pop-up trimmer extends
to trim mustache, sideburns, etc.
■ Slide the power button down to the
OFF position.
To Trim
Trim mustache
■ Connect the supplied AC power cord
to the shaver’s power port and then
to an electrical outlet.
■To activate the shaver, slide the
power button up to the ON position.
■ Trimmer is turned off until it is
extended for use.
■ Use the shaver heads to trim the
lower edge of your mustache. Hold
shaver at desired trim line for a
quick, easy, professional trim.
■ Use the pop-up trim-
mer for the upper edge
of your mustache.
Extend the trimmer
and touch the edge
of it to the desired line.
■ Push the trimmer
button up to pop up
the trimmer.
■Always use a clean, dry
shaver.
■ Make sure the cutter head
assembly is in the locked position.
Charging the R-400
■ Hold the shaver
with the trimmer
toward you when
trimming.
Before using your shaver for the first
time, charge it for 24 hours.
To Shave
NOTE: It may take up to 3 cycles of
full charge and discharge to maximize
battery capacity.
■ Slide the ON/OFF button
to activate the shaver
for shaving.
■After trimming, pull the trimmer
button downward into the OFF
position. Leave it in the down
position when not in use.
Trim sideburns
■ Hold the shaver so all
the heads touch your
face together. This
allows the shaver to
work the way it was
designed for the closest
To charge your shaver
■ Slide the power button downward to
the OFF position.
Extend the trimmer and
touch the edge of it to the
desired trim line.
NOTE (R-400): It is important to always
use the button to close the trimmer to
avoid damaging the locking mechanism.
■ Connect the supplied AC power cord
to the shaver’s power port and then
to an electrical outlet.
6
7
Microflex R_200_400_IB 8/24/06 2:34 PM Page 8
Cleaning and Maintenance
To assure smooth, efficient
performance, it is important
to clean your shaver.
Lubricate
Cleaning Cautions
When is it Time to Replace
Your Heads and Cutters?
Remington® Shaver Saver® Lubricant
(SP-4) lubricates and cleans your
shaver's cutters and head assembly.
The lubricant helps remove hair clip-
pings while reducing wear. A quick
spray after each shave keeps your
shaver operating at peak performance.
■ The construction of this shaver
is for dry operation only. It is
not waterproof. Never put the
shaver partially or completely
into water.
It is very important to replace your
heads and cutters when necessary
to ensure a close, comfortable
shave without irritation. We recom-
mend they be replaced every 12
months. Here are some signs of
head and cutter wear, indicating
that replacement is needed.
Daily
Brush inside the
head assembly
after each use:
1. Turn the shaver
off.
■ Never clean the shaver or
replace the cutters while it is
plugged into an electrical outlet.
■ Do not use an aggressive cleansing
agent as this may destroy the
shaver coatings.
■ Do not clean or remove the head
assembly while the shaver is running
or plugged in, as it may cause dam-
age to the unit's heads or cutters.
■ Replace worn or damaged parts
with Remington® replacement
parts only.
! Important: Make sure to align
the two locating holes in the Cutter
Retainer assembly with the pins in
the Head Frame Assembly. (See
illustration below). Then tighten
center screw knob to lock the
cutters into place.
2. Grip the head
assembly by
the three ridges
and pull it off the
shaver.
3. Use the clean-
ing brush to
sweep out the
internal part of
the head assem-
bly and the hair
pocket area,
where 3 shaver
spindles are
Irritation
As the heads get excessively worn
you may experience some skin
irritation. This would be especially
noticeable when you apply
after-shave lotion.
Replace head assembly on the shaver
simply by pushing it onto the shaver.
Cover shaver head with plastic head-
guard between uses. When removing
the headguard or placing it back onto
the shaver,do not apply pressure to
floating cutter surfaces, as you may
damage them.
Pulling
When the cutters wear you may
feel a sense of pulling and a loss
of closeness when you shave. This
is an indication that it is time to
replace your heads and cutters.
located.
4. Replace head assembly.
The replacement parts for your
shaver is model SP-25.
Cutter retainer
assembly
Weekly
U.S. residents: To order, contact
us at 800-231-8793, visit us at
or visit your local retailer.
Clean under the cutter assembly at
least once a week:
Center
screw
knob
1. Turn the shaver off.
2. Open the head assembly as above.
3. Unscrew the center screw knob
to remove the cutter retainer
assembly.
4. Use the cleaning brush to sweep
the dust and hairs from under the
cutters.
Locating holes
Canadian residents: For any shaver
accessory requirements, please
call800-268-0425 or visit us at
Head/frame
assembly
5. Replace head assembly.
Floating
cutter
heads
Locating pins
8
9
Microflex R_200_400_IB 8/24/06 2:34 PM Page 10
Performance Guarantee
Battery Disposal
SPECTRUM BRANDS, INC. SHALL
CAUTION: DO NOT PUT IN FIRE OR
MUTILATE YOUR BATTERIES WHEN
DISPOSING AS THEY MAY BURST OR
RELEASE TOXIC MATERIALS. DO NOT
SHORT CIRCUIT AS IT MAY CAUSE
BURNS. DISPOSE PROPERLY IN
ACCORDANCE WITH YOUR LOCAL
AND STATE REQUIREMENTS.
Full Two-Year Warranty
Battery Removal (R-400 only)
When your rechargeable shaver
reaches the end of its useful life, the
batteries must be removed from the
shaver and be recycled or disposed of
properly in accordance with your local
and state requirements.
NOT BE RESPONSIBLE FOR ANY
INCIDENTAL, SPECIAL OR CONSE-
QUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT.
ALL IMPLIED WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND
MERCHANTABILITY, ARE LIMITED
IN DURATION TO TWO YEARS FROM
DATE OF ORIGINAL PURCHASE.
Spectrum Brands, Inc. warrants this
product against any defects that are
due to faulty material or workmanship
for a two-year period from the original
date of consumer purchase. This war-
ranty does not include damage to the
product resulting from accident or
misuse.If the product should become
defective within the warranty period,
we will repair it or elect to replace it
free of charge. Return your product
and sales receipt with your name,
address and day time phone number
to: Spectrum Brands, Inc. , Attention:
Consumer Services, 601 Rayovac
Drive, Madison, WI 53711. For more
information call 800-736-4648.
The following procedures should
be followed for battery removal:
■ Make sure your shaver is
unplugged from any
outlets, so you don’t
risk an electrical
The EPA-certified
®
RBRC Battery
This warranty gives you specific legal
rights and you may also have other
rights which vary from state to state
or province to province. Some states
do not allow the exclusion or limitation
of incidental, special or consequential
damages.
Recycling Seal on
the nickel-cadmium
(Ni-Cd) battery indicates
Spectrum Brands, Inc.
shock.
■ Remove the Head
Assembly by gently
lifting the assembly
away from the shaver.
■ Using a small Phillips
head screwdriver,
is voluntarily participating in an
industry program to collect and
recycle these batteries at the end
of their useful life, when taken out
of service in the United States or
Warranty excludes:
■ Screens and cutters
Performance Guarantee
Spectrum Brands, Inc. Money-back
Offer
®
remove the screws
from the upper and
lower back of
Canada. The RBRC program
provides a convenient alternative to
placing used Ni-Cd batteries into the
trash or the municipal waste stream,
which may be illegal in your area.
KEEP ORIGINAL SALES RECEIPT AS
PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
If within 30 days after you have
purchased your Remington® branded
product, you are not satisfied and
would like a refund, return it with the
sales slip indicating purchase price
and date of purchase to the retailer
from whom it was purchased.
Spectrum Brands, Inc. will reimburse
all retailers who accept the product
within 30 days from the date of
purchase. If you have any questions
concerning the money-back
the shaver.
■ Pull or gently pry the
shaver halves apart,
exposing the battery.
■ Hold each battery in
place and very carefully cut the
wires leading to the terminals on
each battery.
SM
Please call 800-8-BATTERY for
This warranty does not cover products
damaged by the following:
■ Accident, misuse, abuse or
alteration of the product
■ Servicing by unauthorized persons
■ Use with unauthorized accessories
information on Ni-Cd battery recy-
cling and disposal bans/restriction
in your area. Spectrum Brands, Inc.
involvement in this program is part
of our commitment to preserving
our environment and conserving
our natural resources.
■ Lift or pry the battery out of the
shaver.
■ Connecting it to incorrect current
and voltage
guarantee, please call 800-736-4648.
■ Wrapping cord around appliance
causing premature wear &
breakage
■ Any other conditions beyond our
control
10
11
Microflex R_200_400_IB 8/24/06 2:34 PM Page 12
Warranty Service
R-200, R-225
120 VAC, 60 Hz
Dist. by: Spectrum Brands, Inc.,
Madison, WI 53711
Dist. by: Rayovac Canada Inc.,
Mississauga, ON L4W 2T7
R-400
105-130 VAC, 60 Hz
105-240 VAC, 50 Hz
MADE IN CHINA
Questions or comments:
Call 800-736-4648 in U.S. or
800-268-0425 in Canada.
products.com
REMINGTON & MICROFLEX and
EASY-VIEW are trademarks of
ROVCAL, INC.
© 2006 ROVCAL, INC.
1/06 Job #CS29563
T22-20903
12
|