LIMITED WARRANTY
This product is warranted to the original consumer purchaser to be free from
defects in materials and workmanship under normal installation, use and service for a
period of one (1) year from the date of purchase as shown on the purchaser’s receipt.
The obligation of Rolls Corporation under this warranty shall be limited to repair
or replacement (at our option), during the warranty period of any part which proves
defective in material or workmanship under normal installation, use and service, provided
the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PRE-
PAID. Products returned to us or to an authorized Service Center must be accompanied by
a copy of the purchase receipt. In the absence of such purchase receipt, the warranty
period shall be one (1) year from the date of manufacture.
RA62b
Six Channel
Stereo Headphone Amplifier
This warranty shall be invalid if the product is damaged as a result of deface-
ment, misuse, abuse, neglect, accident, destruction or alteration of the serial number,
improper electrical voltages or currents, repair, alteration or maintenance by any person or
party other than our own service facility or an authorized Service Center, or any use
violative of instructions furnished by us.
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
LEVEL
LEVEL
LEVEL
LEVEL
This one-year warranty is in lieu of all expressed warranties, obligations or
liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE
LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN
LIMITED WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
PAN
STEREO
INPUT
6 CHANNEL
HEADPHONE AMPLIFIER
MONO
OUTPUT
L
R
RA62b
pwr
STEREO
LEVEL
LEVEL
LEFT INPUTS
IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
R
L
CHANNEL ONE
1/4" OUT
INSERT
LEFT/MONO
INPUT
CHANNEL ONE
1/8" (3.5 mm) OUT
L
RIGHT/STEREO
INPUT
R
L
PAN
CHANNEL TWO
HEADPHONE OUT
INSERT
FRONT PANEL
STEREO IN
R
CHANNEL TWO
1/8" (3.5 mm) OUT
TO CHANNELS
3 THROUGH 6
RIGHT INPUTS
ROLLS CORPORATION
SALT LAKE CITY, UTAH
5/03
OWNERS MANUAL
SCHEMATIC
INTRODUCTION
Thank you for your purchase of the Rolls RA62b Stereo Headphone Amplifier.The
ROLLS RA62b is a six-channel headphone/earphone amplifier for professional
audio monitoring. It is intended for recording studios, sound reinforcement, and
audiophile listening environments where full frequency response signal(s) are to
be distributed to up to six individuals. A variety of input options are available
including 1/4", RCA, and balanced XLR. Since the MONO/STEREO switch is after
the pan control, it will mix 2 MONO signals and their balance can be adjusted with
the Pan control. Up to six individual monitor mixes may be listened to via the rear
panel insert jacks. The RA62b features a FR4 double sided circuit board, socketed
integrated circuits, and painted steel chassis.
This manual assumes the user has a basic knowledge of audio electronic equip-
ment.
FEATURES
• 6: 1/4" Headphone and 6: 1/8" (3/5 mm) Earphone Outputs per channel with
Level Controls
• 1/4" and 1/8" Outputs may be used simultaneously
• 1/4", RCA and XLR Inputs
• 6 TRS Stereo Insert jacks for separate use of each channel
• Up to 600 mW output per jack - it's loud
• Stereo/Mono Switch - allows mixing 2 mono signals
• Front and rear panel input jacks
• May be used as a six channel Distribution Amplifier
• FR4 Double-sided fiberglass epoxy circuit board
• Socketed ICs
• Made in the U.S.A.
WARNING
USING THIS SYSTEM AT EXCESSIVE VOLUMES CAN CAUSE
PERMANENT HEARING DAMAGE.
USE AS LOW A VOLUME AS POSSIBLE
In order to use this system safely, avoid prolonged listening at excessive sound
pressure levels. Please use the following guidelines established by the Occupa-
tional Safety Health Administration (OSHA) on maximum time exposure to sound
pressure levels before hearing damage occurs.
90 dB SPL at 8 hours
95 dB SPL at 4 hours
100 dB SPL at 2 hours
105 dB SPL at 1 hour
110 dB SPL at 1/2 hour
115 dB SPL at 15 minutes
120 dB SPL - avoid or damage may occur
5
2
DESCRIPTION
CONNECTION
FRONT PANEL
Connect the AC cord to a properly grounded ac outlet.
PAN
STEREO
INPUT
6 CHANNEL
HEADPHONE AMPLIFIER
MONO
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
Determine which input configuration you will use; either discreet right/left, TRS
stereo, or mono.
L
R
RA62b
pwr
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
LEVEL
STEREO
Note: Descriptions for Channel One through Channel Six are identical.
OUT 1 - 6 : 1/4” and 1/8” (3.5 mm) Tip-Ring-Sleeve jacks for connection to a
standard pair of headphones or earphones. These jacks may be used simulta-
neously.
VOLUME 1 - 6: Controls the amount of output signal from the indicated channel.
MONO/STEREO SWITCH: When this switch is pressed in, the Right and Left
channels are summed together providing a mono output signal.
PAN: Controls the relative amount of signal sent to the Right and Left output
channels.
For a discreet right/left input configuration, connect a balanced XLR plug contain-
ing the “Right” portion of the stereo signal to the Right Main Input. Connect a
balanced XLR plug containing the “Left” portion of the stereo signal to the Left
Input.
For a TRS stereo input configuration, connect a Tip-Ring-Sleeve stereo plug into
the front panel STEREO IN input.This cable may come from a mixer’s headphone
output for example.
STEREO IN: 1/4” TRS input jack which parallels the rear panel Right and Left
input jacks.
POWER LED: Indicates that the RA62 is connected to the power supply and is
on.
The Aux Inputs are connected in the same manner as the discreet right/left input
configuration listed above.
To send a mono signal to the RA62b, connect an XLR jack to either Main Input, or
a single 1/4” Tip-Sleeve or RCA plug into either Aux Input input and press in the
front panel MONO/STEREO switch.This mono signal will be fed to both the right
and left sides of the headphone outputs.
REAR PANEL
MAIN INPUTS
AUX INPUTS
RIGHT
SERIAL NUMBER
MODEL RA62b
62-
LEFT
RIGHT
INSERT
6
INSERT
5
INSERT
4
INSERT
3
INSERT
2
INSERT
1
LEFT
CAUTION
LEFT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RIGHT
120 VAC
50/60 Hz 15 VA
MADE IN U.S.A.
WARNING:
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK.
NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
RISQUE DE CHOC
-
NE PAS ENLEVER
120 VAC INPUT: Connects to a properly grounded AC outlet.
INSERTS
MAIN INPUTS: Balanced XLR jacks for connecting to the desired Right and Left
program material.
The inserts have been provided so you can directly access each headphone
output with its own program material.
AUX INPUTS: 1/4” and RCA unbalanced inputs - for use in the event additional
program material is to be mixed with the main inputs, or if XLR plugs are not
available.
The inserts require Tip-Ring-Sleeve connectors, with right and left signals on the
tip and ring respectively. If you use a TS mono plug - you will only hear sound out
of one side.
When these insert jacks are used, the main Right/Stereo and Left/Mono, as well
as the Aux Inputs - are disconnected. Only the stereo signals sent to the Insert
jacks go to that corresponding output.
Note:The description for the Channel Inserts pertains to all six channels.
CHANNEL INSERTS: 1/4” TRS jacks which directly access the channel’s
heaphone output circuitry. This is a stereo jack and requires a TRS stereo signal.
CAUTION: Plugging a mono 1/4” TS plug into the Headphone
Outputs may cause permanent damage to the unit because
one side would be shorted to ground. NEVER PLUG A MONO
PLUG INTO ANY OF THE HEADPHONE OUTPUTS.
Tip
Ring
Sleeve
(ground)
4
3
|