VX410
VX410a
series
VX115 BASS
4 x10″ + 1″ High Frequency CD
Bass Enclosure
Hartke
Connecting the VX410 and VX410a
About Impedance
Before you hook up your speaker cabinet be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance; When two speakers are wired in "Parallel"
EFFECT
the total impedance is cut in half and
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
when two speakers are wire is “Series”
the total impedance is the sum of the
speakers individual impedance.
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
The VX410 and VX410a’s impedance
(many audio guys used the made up
word “ohmage”, however the correct
term is impedance) is 8 Ohms. So,
when two VX410’sor VX410a’s are con-
nected together in parallel the total
impedance is 4 Ohms. The impedance
of your speaker also has an effect on
you amplifier. In general, the lower the
impedance the more power your ampli-
fier will put out.
Hartke
-series
VX410 BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
IMPORTANT: There is an minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
EFFECT
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
Connecting the VX410 to Your Amplifier
The VX410 and VX410a connections
are made via 1/4” phone jacks located
on the rear panel jack-plate. Be sure to
make your connection with un-shielded
speaker cable. Connect the Amplifier
Output to the speaker Input on the
VX410’s rear jackplate.
Hartke
-series
VX410 BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
Using the EXTENSION Output
The VX410and VX410a provides a
convenient Extension Output for con-
necting additional speaker cabinets in
parallel. Be sure to read the section
above on impedance to insure a proper
hook up with your amplifier. Follow the
steps below to connect two VX410’s
using the Extension Output. Connect
the Amplifier Output to the Input of the
first VX410. Now, connect the
Hartke
-series
Extension Output to the Input of the
second VX410 or VX410a.
VX410 BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
VX410 and VX410a Specifications
Type
Bass speaker enclosure
Impedance (Ohms)
Power Handling
8 Ohms Impedance
400 Watts Peak Power Handling
Low Frequency Drivers
High Frequency Driver
Dimensions
4-10″ Special Design 8 ohm, 100
wattSpeakers,
1″ Throat Compression Driver
Height:25″ (62.2 cm)
Width: 25″ (62.2 cm)
Depth: 15″ (47.0 cm)
Weight
VX410
VX410a
72 lbs. (32.6 kg)
70 lbs. (31.68 kg)
Specifications subject to change without notice.
Hartke
Distributed Worldwide Exclusively by:
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
|