Quick Installation Guide
TEG-PCBUSR
1. ×òî íóæíî ñäåëàòü â ñàìîì íà÷àëå
Äèñêîâîä CD-ROM
Ãíåçäî äëÿ PC êàðò CardBus Type II
ÖÏ: Intel Pentium 300 ÌÃö èëè áîëåå
Ïàìÿòü: ÎÇÓ 64 ÌÁ èëè áîëåå
Windows 98SE/ME/2000/XP
Ïðèìåíåíèå
32-Bit Gigabit CardBus PC Card
(TEG-PCBUSR)
5-Port 10/100/1000Mbps
Copper Gigabit Switch
(TEG-S50TXE)
32-bit 10/100/1000Mbps
Copper Gigabit PCI Adapter
(TEG-PCITXR)
32-bit 10/100/1000Mbps
Copper Gigabit PCI Adapter
(TEG-PCITXR)
1
Ðóññêèé
2. Ïîðÿäîê óñòàíîâêè
Ïðèìå÷àíèå: óñòðîéñòâî TEG-PCBUSR ðàññ÷èòàíî íà «ãîðÿ÷åå»
ïîäêëþ÷åíèå, ò. å. íà âîçìîæíîñòü åãî ïðèñîåäèíåíèÿ è îòñîåäèíåíèÿ áåç
ïåðåçàãðóçêè êîìïüþòåðà.
1. Ïîÿâèòñÿ Ìàñòåð óñòàíîâêè
íîâîãî îáîðóäîâàíèÿ,
âûáåðèòå Íåò, íå ñåé÷àñ, çàòåì
ùåëêíèòå ïî êíîïêå Äàëåå.
2. Óñòàíîâèòå CD-ROM-äèñê ñ
äðàéâåðîì â äèñêîâîä CD-ROM
êîìïüþòåðà.
3. Âñòàâüòå äèñê CD-ROM â
äèñêîâîä è âûáåðèòå
Óñòàíîâèòü ïðîãðàììíîå
îáåñïå÷åíèå àâòîìàòè÷åñêè
(ðåêîìåíäóåòñÿ), çàòåì
ùåëêíèòå ïî êíîïêå Äàëåå.
4. Ùåëêíèòå ïî êíîïêå Çàâåðøèòü.
2
Ðóññêèé
Troubleshooting
Q1: Windows is unable to recognize my hardware. What should I do?
A1: First, verify that your computer meets the system requirements as specified in
Section 1. Second, go to Start -> Control Panel -> Hardware -> Device
Manager. In the list of device types, double-click on Network Adapters. If you
see the device with a yellow question mark or exclamation point next to it, double-
click on it, click on Drivers and click Update Drivers. Follow the Hardware
Update Wizard instructions as illustrated in Section 2. Third, if the device
manager fails to recognize the presence of a new networking adapter, verify that
the network adapter is firmly seated in the PC CardBus slot. Fourth, install the
adapter into another available PC CardBus slot
Q2: Windows recognizes my new hardware, but I'm unable to connect to my
network. What should I do?
A2: First, verify that the RJ-45 Ethernet Cable is securely connected from your
switch or router to your network adapter. Second, verify that the LEDs on your
network card are lit. Third, verify that the TCP/IP settings are set to Obtain an IP
address automatically.
Q3: When I connect the adapter to a gigabit switch, I am not getting gigabit
speeds. What should I do?
A3: Make sure you are using CAT-5e or CAT-6 Ethernet Cables. Some CAT-5
cables are not rated to run in Gigabit.
If you still encounter problems or have any questions regarding the TEG-PCBUSR,
please refer to the User's Guide included on the Driver CD-ROM or contact TRENDnet's
Technical Support Department.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may cause
undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
3
TRENDnet Technical Support
.
US Canada
Toll Free Telephone: 1(866) 845-3673
24/7 Tech Support
.
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)
Toll Free Telephone: +00800 60 76 76 67
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Product Warranty Registration
Please take a moment to register your product online.
3135 Kashiwa Street
Torrance, CA 90505
USA
Copyright ©2006. All Rights Reserved. TRENDnet.
|