5742
Body Fat Analyzer
and Scale
®
Leading the Way in Accuracy
Instruction Manual
BATTERY INFORMATION AND GENERAL SET-UP
This scale operates on 4 AAA batteries (included).
Insert the 4 AAA batteries into the battery compartment. Ensure the + and -
terminals are the correct way round.
Some models have a static cling label on the lens to prevent scratching.
Please remove before use.
Your scale has been set to measure in pounds and inches
(lb). To change the measurement units to kilograms/centimeters or
stone/inches, move the switch on the bottom of the scale to
(kg) or (st-lb).
Place the scale on a flat, hard surface. Carpeted or uneven
floors may affect accuracy.
When the LCD displays “Lo”, replace the batteries.
The scale needs to be initialized before first use or
after battery replacement. Press lightly on the scale
Tap to initialize
platform. The display will show a running zeros pattern and automatically
turn off. Your scale is now ready for use.
WEIGHT ONLY OPERATION
Your Taylor® Body Fat Scale will operate as a basic weight-reading scale.
No special programming steps are required.
Once the scale is initialized, as
previously described, you may
simply step on the scale to obtain
your current weight. For a weight
only reading:
1. Place the scale on a flat, hard
surface. Carpeted or uneven
floors may affect accuracy.
2. Step onto the scale platform and remain still while the scale computes
your weight.
3. The display will flash twice when the weight is locked. Your weight is
now displayed.
4. The scale will automatically turn off.
3
USING YOUR BODY FAT SCALE
In order to measure body fat and body water, you must first enter your
height, age, and gender. The analyzer uses these factors to calculate your
results. Onscreen prompts will lead you through programming your personal
information into the analyzer. The analyzer will then use this data to com-
pute your body fat/body water percentages.
You must have bare feet to use the body fat analyzer function.
Remove your shoes and socks before proceeding. To get the most accurate
and consistent reading, wipe your feet with a damp cloth, leaving them
slightly damp before stepping on the scale.
REMINDER: The scale needs to be initialized after battery installation. The
scale may also need to be initialized if it is moved or bumped. At all other
times, you may directly proceed with the following instructions for
programming your personal data into the scale.
To initialize the scale, simply press lightly on the scale platform. The display
will show “0000” and automatically turn off. Your scale is now ready for use.
BODY FAT AND BODY WATER MEASURING OPERATION
In order to measure body fat/body water, you must first enter your height,
age, and gender. The analyzer uses these factors for body fat and body
water calculations. This analyzer also has an athlete mode option, which
uses additional software to calculate more accurate results for highly fit
individuals. Onscreen prompts will lead you through programming your
personal information into the analyzer. The analyzer will then use this
data to compute your body fat/body water percentages.
Your data may be stored into memory for future use, thus eliminating the
need to enter your personal information before each reading (see the
next section about “Memory Functions”).
1. You must have bare feet to use the body fat analyzer function. Remove
your shoes and socks now, before proceeding with Step 2. To get the most
accurate and consistent reading, wipe your feet with a damp cloth, leav-
ing them slightly damp before stepping on the scale.
2. Press the ON button to turn the scale on. The height digits blink.
3. Press the (▲) or (▼) button to increase / decrease the height value. Press
the SET button to confirm displayed height. The age digits blink.
4. Press the (▲) or (▼) button to increase / decrease the age value. Press
SET button to confirm displayed age. A gender icon blinks.
5. Press the (▲) or (▼) button to toggle between the male and female gender
icons. Press SET button to confirm your gender. The normal or athlete
mode icon blinks.
6. Press the (▲) or (▼) button to toggle between athlete mode and normal
mode. (Please note: this selection is only available to those aged 18 or
4
older. For ages 17 or under, this step is automatically bypassed).
7. Press the SET button to confirm all settings. A “beep” sound and an “R”
icon on the LCD screen indicate successful programming, Your personal
data is now saved in memory.
8. Repeat procedure for a second user.
MEMORY FUNCTIONS
This scale has 4 personal memory settings. You may save your height, age,
gender, and normal/athlete selections into one of these memories. Once your
personal data has been stored into memory, you may take a reading simply
by accessing your memory number and stepping on the scale. Please see the
next two sections entitled “To Store Data into Memory” and “To Access and
Use Memory Data”.
To Store Data into Memory
1. Follow steps 1-7 in the Body Fat Measuring Operation section above. A
beep sounds in Step 7 after you enter your personal data.
2. Press the (▲) or (▼) button to select a memory (1 - 4). The memory num-
ber appears on the screen.
3. Press the SET button to confirm. A “beep” will sound. Your height, age,
gender and normal/athlete values are saved in that memory number (1-4).
4. You may step on the scale for a measurement at this time. Otherwise,
the scale will turn off automatically. Your data remains saved in memory.
To Use Memory Data
1. Press and hold the SET button for 2 seconds while the power is off.
2. Press (UP) / (DOWN) button to scroll to the desired memory number.
3. When your memory number appears on the screen, press the SET button
to select. A “beep” will sound. Your data will toggle on the screen.
4. Step on the scale with bare feet. Stand still while the scale measures
your weight.
5. Your weight will display for 2 seconds. Continue to stand still on the
scale.
6. The scale will start to measure body fat % and body water %. The LCD
will show spinning zeroes (“0000”) while the scale computes.
7. A “beep” sounds when measurement is complete. Remain on the scale. The
body fat %, body water % and weight will appear in sequence.
8. The scale turns off automatically.
TO TURN OFF THE SCALE:
To turn the scale off, press the ON button. Or, the scale will turn off after
about 20 seconds if no keys are pressed or nothing is weighed.
NOTE: If you are having a problem operating this Analyzer please call 866-
843-3905 from 7:30 am to 4:30 pm, Mountain Standard Time, Monday
through Friday.
5
QUESTIONS AND ANSWERS
How exactly is my body fat and water being measured?
The Taylor Body Analyzer Scale uses a measurement method known as
Bioelectrical Impedance Analysis (BIA). A minute current is sent through
your body, via your feet and legs. This current flows easily through the lean
muscular tissue, which has a high fluid content, but not easily through fat.
Therefore, by measuring your body’s impedance (i.e. its resistance to the cur-
rent), the quantity of muscle can be determined. From this, the quantity of
fat and water can then be estimated.
What is the value of the current passing through me when the meas-
urement is taken? Is it safe?
The current is less than 1mA, which is tiny and perfectly safe. You will not
be able to feel it. Please note however, that this device should not be used by
anyone with an internal electronic medical device, such as a pacemaker, as a
precaution against disruption to that device.
If I measure my body fat and water at different times during the
day, it can vary quite considerably. Which value is correct?
Your body fat percentage reading varies with body water content, and the
latter changes throughout the course of the day. There is no right or wrong
time of the day to take a reading, but aim to take measurements at a regular
time when you consider your body to be normally hydrated. Avoid taking
readings after having a bath or sauna, following intensive exercise, or within
1-2 hours of drinking in quantity or eating a meal.
My friend has a Body Fat Analyzer made by another manufacturer.
When I used it I found that I got a different body fat reading to that
on my Taylor Body Analyzer Scale. Why is this?
Different Body Fat Analyzers take measurements around different parts of
the body and use different mathematic algorithms to calculate the percent-
age of body fat.The best advice is to not make comparisons from one device
to another, but to use the same device each time to monitor any change.
Why are the body fat percentage ranges for men and women so dif-
ferent?
Women naturally carry a higher percentage of fat than men, because the
make-up of the body is different being geared towards pregnancy, breast-
feeding etc.
6
Why should I avoid using the Taylor Body Analyzer Scale while
pregnant?
During pregnancy a woman’s body composition changes considerably in
order to support the developing child. Under these circumstances, body fat
percentage readings could be inaccurate and misleading.
Why is the Taylor Body Analyzer Scale unsuitable for athletes and
children?
The body compositions of both athletes and children require different mathe-
matic algorithms for the body fat calculation.
TROUBLE SHOOTING
1. You must have bare feet to make this measurement. To get the most
accurate and consistent reading, wipe your feet with a damp cloth,
leaving them slightly damp before stepping on the scale. Measurement
again, maintaining maximum contact between your feet and the metal
sensors.
2. The condition of the skin on the bottom of your feet can affect the
reading. The natural effects of aging or activity can make this skin hard.
Take the reading with clean, slightly damp feet for best accuracy.
3. Please note that body fat contains some body water weight. Thus, body
fat and body water percentages will not add up to 100%.
If you are having a problem operating this Analyzer please call 866-843-3905
from 7:30 am to 4:30 pm, Mountain Standard Time, Monday through Friday.
7
WARNING MESSAGES
CAUTION
BIA (Bioelectrical Impedance Analysis) method determines your body fat
percentage by sending a harmless signal through the body. Do not use this
product if you have a pacemaker or other internal medical device.
When in doubt, contact your physician.
This analyzer will give accurate body fat readings for a majority of people,
but is not intended for use by the following groups:
Children: Anyone under the age of 18 years
Pregnant Women
GENERAL INFORMATION ABOUT BODY FAT AND BODY WATER
1. Ideal body fat content is not the same for all people. Age, sex, and
heredity are variables in this measurement. The table
as follows may be used as a general guide. Consult your physician to
determine what is most ideal for you.
8
Body Water
3. It is recommended to measure body fat, body water or weight at the
same time period daily. Please note that body fat contains some
body water weight. Thus, body fat and body water percentages
will not add up to 100%.
4. Use this product without clothing for best accuracy. Clothes can vary in
weight and affect the percentage calculation.
5. Feet must be bare and clean. For best readings they should also be
slightly damp.
LEVEL OF HYDRATION
This analyzer measures your weight, the electrical impedance between your
feet, and combines those readings with the information you input (Height,
Age, Gender). It then automatically calculates your body fat and body water
percentage.
Your level of hydration (water content) varies throughout the day and affects
your impedance measurement. If you are dehydrated, there is a greater
chance for fluctuation in the body fat and body water percentage displayed
by this analyzer than when you are fully hydrated.
For best results, choose a consistent time to use this analyzer, such as in the
morning. By establishing the pattern of your body’s fluctuation over a period
of one month, you can determine your average level of body fat. Women will
have more fluctuation in water content than men and need to monitor their
reading over a longer time period to establish a personal average. You must
determine this as a reference point before measuring progress in a health
program.
9
You must wait several hours before taking a body fat reading when:
drinking coffee or alcohol, taking diuretic medications, or exercising. These
all affect your level of hydration and the accuracy of this analyzer.
SPECIFICATIONS
•
Uses BIA (Bioelectrical Impedance Analysis) to determine body fat and
body water percentage
•
•
•
•
•
•
•
•
Weight Capacity: 350 lb or 160 kg or 25 st
Weight Graduation: 0.2 lb or 0.1kg or 0.25lb
Body Fat Graduation: 0.1% (in the range from 4% - 50%)
Body Water Graduation: 0.1% (in the range from 37% - 70%)
Height Range: 3' 3.4” – 7' 2.6” (100.0 – 220.0cm)
Age Range: 10-99 years
Weight-only feature with automatic step on
Data can be stored for up to 4 individuals
PRECAUTIONS
1. OVERLOAD WARNING: the maximum weight capacity of this scale is
350 lbs / 160 kgs / 25 st. Remove the weight immediately when the scale
displays “Err2”; otherwise, permanent damage to the scale will occur.
2. The product is intended for home / consumer use only; it is not intended
for professional use in hospitals or medical facilities.
3. Do not disassemble the product. Other than replacing the battery, it
contains no user serviceable parts.
4. Clean after use with a lightly dampened cloth. Do not use solvents or
immerse the product in water.
5. Your scale contains sensitive electronic parts. Avoid rough treatment. Do
not drop, kick, or jump on it. Treat it with care to ensure the best
performance.
6. Do not store the scale where you store cleaning chemicals. The vapors
from some household products may affect the electronic components
of your scale. Do not store the scale on its side.
7. This scale is a sensitive weighing device. To prevent run down of the
battery, do not store anything on the scale.
8. Do not dispose of batteries in fire. Batteries may explode or leak. Do not
mix old and new batteries. Do not mix Alkaline, carbon-zinc (standard)
or Nickel-Cadmium (rechargeable) batteries. Remove the battery if the
scale will not be used for a long period of time.
10
TEN (10) YEAR LIMITED WARRANTY
This scale is warranted against defects in materials of workmanship for ten
(10) years for the original purchaser from date of retail purchase. It does not
cover damages or wear resulting from accident, misuse, abuse, commercial
use, or unauthorized adjustment and/or repair.
Do not return to retailer. Should this scale require service (or replacement at
our option) while under warranty, please pack the item in the original pack-
aging and return it prepaid, along with store receipt showing date of pur-
chase and a note explaining reason for return to:
Taylor Precision Products
2220 Entrada Del Sol, Suite A
Las Cruces, New Mexico 88001
There are no express warranties except as listed above. This warranty gives
you specific legal rights, and you may have other rights which vary from
state to state.
For additional product information, or warranty information in Canada or
elsewhere outside the USA, please contact us through www.taylorusa.com.
©2008 Taylor Precision Products and its affiliated companies, all rights
reserved. Taylor® and Leading the Way in Accuracy® are registered trade-
marks of Taylor Precision Products and its affiliated companies. All rights
reserved.
11
|