Model CF-980
TM
Centurion
Water Filtration Vacuum
by Top Innovations, Inc.
Please read instructions before use.
Mail in your warranty registration card.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of fire, electrical shock, or
injury, the following basic safety precautions should always
be followed when using an electrical appliance.
READ ALL INSTRUCTIONS BEFORE USING YOUR VACUUM
TM
1) DO NOT leave your CF-980 Centurion unattended when plugged in or
not in use.
2)
This unit is not a toy. Close supervision is required when using
unit near children, pets, and plants.
3) Always unplug electrical cord when unit is not in use. DO NOT use this
unit if electrical cord or outlet is damaged. DO NOT use unit if it is not
working properly or has been dropped, damaged, or left outdoors. If such
damage occurs, contact an approved service technician for assistance.
4) This unit is an electrical appliance. DO NOT submerge it in water. DO
NOT use electrical cord or hose as a handle. DO NOT allow cord or hose to
be crimped by closing it in doors. DO NOT pull or stretch cord or hose
around sharp corners or edges. Be sure to keep electrical cord away from all
heated surfaces.
5) DO NOT use this unit with extension cords or electrical outlets that have
inadequate current capacity. A three-prong outlet or a properly grounded
TM
adapter is necessary when using CF-980 Centurion .
TM
6) In order to unplug CF-980 Centurion , grasp plug and pull smoothly and
firmly from outlet. DO NOT attempt to unplug unit by pulling or tugging on
cord.
7) DO NOT handle or use this unit while hands are wet or when not wearing
shoes.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
3
Top Innovations, Inc.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of electric shock, this appliance
has a three-pronged plug. This plug will fit in a polarized wall
outlet only one way. If the plug does not fit fully in the outlet,
contact a qualified electrician to install a proper outlet. DO NOT
attempt to modify the plug or defeat this safety feature in any way.
TM
8) CF-980 Centurion is only meant to be used with recommended
CF-980 accessories. Other types of attachments such as those used with
TM
other vacuum cleaners are not to be used with Centurion . Doing so may
cause injuries or damage to unit.
TM
9) DO NOT use Centurion to vacuum liquids. DO NOT vacuum matches,
ashes, or cigarette butts that are still lit.
10) DO NOT turn unit on its side when in use.
TM
11) When filling your Centurion with water, DO NOT overfill Water
Reservoir. Doing so may cause damage to main unit motor.
12) Before filling or emptying Water Reservoir, always take the following
steps:
1) Turn appliance off
2) Unplug electrical cord
Failure to follow these steps may result in electric shock and injury.
13) Only water should be used in unit. Other cleaning agents will damage
unit and can cause injuries.
14) Keep hair, loose clothing, fingers, and all parts of the body away from
openings and moving parts.
TM
15) Store your CF-980 Centurion in a cool, dry place. Always drain and
clean Water Reservoir before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Top Innovations, Inc.
4
CF-980 CENTURIONTM PRODUCT INFORMATION
The following features and accessories come with your steam cleaner. Carefully inspect
packaging material as some parts are shipped inside Styrofoam packaging. To obtain possible
missing parts, refer to the Customer Support section on page 13 of this manual.
UNIT FEATURES AND
ACCESSORIES
1) Inlet Nozzle Hole
2) Suction Power Control
3) On/Off Switch
4) Grounded Power Cord
5) Side Vent Panel
6) Removable Suction Tube
7) Sponge Filter
8) ULTRA Filter
9) Suction Tube Inlet
10) Sponge Filter Inlet
11) Maximum Fill Line
12) Water Reservoir
13) Locking Handle
14) Power Cord Holders
15) Large Wheels
16) Front Caster
17) Telescopic Extension Tube
18) Flexible Hose
19) Inlet Nozzle
20) Accessory Holder
21) Main Siphon
22) Floor Brush
23) Crevice Tool
24) Upholstery Tool
Top Innovations, Inc.
5
CF-980 CENTURIONTM PRODUCT INFORMATION
· The Inlet Nozzle Hole (1) is where the Inlet Nozzle of the Flexible Hose connects to
the main unit.
· The Suction Power Control (2) lets you adjust how powerful the vacuum suction is.
· The On/Off Switch (3) activates and deactivates the unit.
· The Grounded Power Cord (4) provides exceptional mobility while protecting
against electric shock and injury.
· The Side Vent Panel (5) is where exhaust is emitted from the unit. The left Side
Vent Panel (not shown) is removable and houses the ULTRA filter.
· The Removable Suction Tube (6) is inserted into the removable water tank and
funnels vacuumed materials into the water in the Water Reservoir.
· The Sponge Filter (7) is inserted into the removable water tank and provides extra
filtration. It uses a built-in safety float to control the amount of water and materials
that is drawn through the filter.
· The ULTRA Filter (8) fits inside the left Side Vent Panel, and helps to prevent
dust and other impurities from being released back into the air.
· The Suction Tube Inlet (9) is where the Suction Tube is inserted into the removable
water tank. Water is also poured into the Water Reservoir through this hole.
· The Sponge Filter Inlet (10) is where the Sponge Filter is inserted into the removable
water tank.
· The Maximum Fill Line (11) indicates the maximum amount of water that can safely
be poured into the Water Reservoir, and should never be exceeded.
· The Water Reservoir (12) is where water is poured to assist in the filtration process.
· The Lifting Handle (not shown) located in the middle-bottom of the main water tank
allows you to more easily lift the main water tank into and out of the cradle car.
· The Locking Handle (13) flips up to securely attach the removable water tank and
the main unit to the cradle car.
· The Power Cord Holders (14) are the pegs that the Grounded Power Cord is looped
around for safe and convenient storage.
· The Large Wheels (15) and Front Caster (16) work in conjunction to provide
exceptional freedom and maneuverability.
· The Telescopic Extension Tube (17) is attached to the Main Siphon and greatly
increases your reach, allowing you to more easily vacuum floors and hard to reach
surfaces.
· The Flexible Hose (18) connects the Main Siphon to the main unit, and allows you
the flexibility for any vacuuming needs. It connects to the main unit via the Inlet
Nozzle (19), and is equipped with an Accessory Holder (20), which can be slid to
any point along the Flexible Hose and conveniently stores the Crevice Tool and
Upholstery Tool. The Main Siphon (21) serves as the handle while vacuuming, and
the nozzle to which the Telescopic Extension Tube is attached.
· The Floor Brush (22) attaches to the end of the Telescopic Extension Tube and can
be used to clean both carpeted and hardwood floors.
· The Crevice Tool (23) may be attached to the Telescopic Extension Tube in place of
the Floor Brush, and is designed for cleaning in narrow, hard-to-reach places.
· The Upholstery Tool (24) may be attached to the Telescopic Extension Tube in
place of the Floor Brush, and is designed to safely and effectively clean furniture,
curtains, and other upholstered surfaces.
6
Top Innovations, Inc.
ASSEMBLING THE
C
ENTURIONTM
ASSEMBLING MAIN UNIT
1) Insert removable water tank onto cradle
car (FIGURE 1). A raised cylinder in bottom
of tank (directly under the Suction Tube
Inlet) will line up with peg at front of cradle
car.
2) Insert Removable Suction Tube into
Suction Tube Inlet as shown (FIGURE 2-A).
Align it with the shape of the hole, and press
down to make sure it is set securely in place.
FIGURE 1
3) Insert Sponge Filter into Sponge Filter
Inlet as shown (FIGURE 2-B). Align it with
the shape of the hole, and press down to
make sure it is set securely in place.
4) Insert main unit into removable water
tank as shown (FIGURE 3). It will not snap
into place, but will be held securely when
Locking Handle is flipped up into place as
shown (FIGURE 4). Main unit, removable
water tank, and cradle car will be held
securely together when Locking Handle
snaps into place.
FIGURE 2
FIGURE 4
FIGURE 3
Top Innovations, Inc.
7
ASSEMBLING THE
C
ENTURIONTM
ATTACHING HOSE AND
ACCESSORIES
1) Insert Inlet Nozzle of Flexible Hose into
Inlet Nozzle Hole on main unit as shown
(FIGURE 5). Insert it so that guides on sides
of Inlet Nozzle (FIGURE 5-A) fit between
tabs inside Inlet Nozzle Hole (FIGURE 5-B).
Turn Inlet Nozzle clockwise until snug.
2) Slide Telescopic Extension Tube onto end
of Main Siphon as shown (FIGURE 6).
Firmly press Tube onto Siphon until it is
snug and secure.
FIGURE 5
3) Attach Floor Brush (FIGURE 7-A),
Crevice Tool (FIGURE 7-B), or Upholstery
Tool (FIGURE 7-C) onto end of Telescopic
Extension Tube as shown (FIGURE 7).
Firmly press attachment onto Tube until it is
snug and secure.
FIGURE 7
FIGURE 6
Top Innovations, Inc.
8
USING THE
C
ENTURIONTM
FILLING WATER RESERVOIR
1) Release Locking Handle and pull it back to rest on top of Power
Cord Holders.
2) Carefully remove main unit from removable water tank and set it
aside.
3) Using Lift Handle in bottom of removable water tank, lift water tank
out of cradle car, and carry it to a convenient sink or tub.
4) Remove Suction Tube from Suction Tube Inlet, fully exposing inlet
hole. Note that this step is not necessary, but may make it easier to pour
water into Water Reservoir.
5) Begin pouring water through inlet hole into Water Reservoir.
Ordinary tap water of mild temperature is ideal.
IMPORTANT: When pouring water into Water Reservoir, DO
NOT exceed Maximum Fill Line mark on side of removable water
tank. Doing so may cause damage to main unit motor.
6) Replace Removable Suction Tube into Suction Tube Inlet (if you
chose to remove it in Step 4).
7) Once again using Lift Handle, carefully place filled water tank back
onto cradle car.
8) Replace main unit back into removable water tank, and return
Locking Handle to its upright position to secure the unit together.
Top Innovations, Inc.
9
USING THE
C
ENTURIONTM
VACUUMING
1) Make sure main unit, removable water tank, and cradle car are fully
assembled (see directions on pages 7 and 8 of this manual for assistance),
and ensure that Locking Handle is securely in place.
2) Connect hose to main unit. Connect Telescopic Extension Tube to Main
Siphon. Connect desired attachment (Floor Brush, Upholstery Tool, Crevice
Tool) to Telescopic Extension Tube.
3) Plug Grounded Power Cord into a convenient three-prong electrical
outlet.
4) Press On/Off Switch once to activate unit. You are now free to begin
vacuuming.
5) Suction power of vacuum can be controlled by setting Suction Power
Control switch to either high or low setting. High setting is recommended as
default setting, but you may find low setting is more effective in certain
situations (such as vacuuming especially delicate drapes and upholstery).
NOTE: Suction power may also be adjusted using control switch on
Main Siphon. See “Main Siphon” section on page 11 of this manual for
more details.
6) Once vacuuming task is completed, press On/Off Switch once to
deactivate unit. Immediately unplug Grounded Power Cord from electrical
outlet.
7) Refer to Proper Storage section on page 12 of this manual for
information on appropriate steps for cleaning and storage of Centurion .
TM
Top Innovations, Inc.
10
USING THE CENTURION’STM ACCESSORIES
MAIN SIPHON
Suction power may be controlled
using secondary control switch on
top of Main Siphon (FIGURE 8).
Reducing suction power allows you
to safely change attachments, and
allows safe usage on delicate fabrics
and upholstery.
FIGURE 8
TELESCOPIC EXTENSION TUBE
Telescopic Extension Tube length may be adjusted using switch at end
of tube (FIGURE 9). Simply depress switch and pull extension end of
tube outwards. Once you have reached desired length, release switch
and shift extension end slightly until it “clicks”. This will cue you that it
is securely locked in place.
FIGURE 9
FLOOR BRUSH
Floor Brush may be effectively used
on both carpeted and hardwood
floors by pressing brush height
adjustment switch into either
“lowered” or “raised” positions.
For vacuuming carpeted floors, set
brush height adjustment switch to
“lowered” position (FIGURE 10-A).
For vacuuming hardwood floors, set
brush height adjustment switch to
FIGURE 10
“raised” position (FIGURE 10-B).
11
Top Innovations, Inc.
CARE AND STORAGE GUIDELINES
CLEANING / REPLACING ULTRA FILTER
1) Remove main unit from removable water tank.
2) Holding main unit upside-down in your lap, press in and outwards on locking tab (note
only left Side Vent Panel has this tab and is removable). While still pressing on tab, pull
Side Vent Panel outwards to disconnect it (FIGURE 11).
3) Gently press in on bottom of ULTRA filter to push the top outwards. Grasp top of filter
and pull it outwards to remove it from its housing (FIGURE 12).
4) Gently and thoroughly rinse ULTRA filter under lukewarm running tap water.
IMPORTANT: Allow ULTRA filter to COMPLETELY DRY before reinserting it back
into main unit housing.
5) Once ULTRA filter is reinserted, reattach Side Vent Panel by first inserting locking tab,
then swinging other end of vent into housing. Side Vent Panel should “click” securely
into place.
FIGURE 11
FIGURE 12
In order to maximize the effectiveness of your Centurion’sTM filtration system, it is
recommended that you replace the ULTRA filter every 2-4 months (depending on
frequency of use). For more information on ordering replacement ULTRA filters,
please refer to the Accessory Ordering Guide on page 14 of this manual.
PROPER STORAGE
Preparing your CenturionTM for storage is quick and simple. When you have finished your
vacuuming tasks, follow the steps listed below:
1) Unplug Grounded Power Cord from electrical outlet.
2) Remove all attachments and accessories from unit.
3) Remove main unit from removable water tank.
4) Remove water tank from cradle car. Drain any remaining water in Water Reservoir into
a sink or tub. Flush out Water Reservoir with fresh water to remove any remaining dirt
or materials from Water Reservoir.
5) Remove Sponge Filter from removable water tank and thoroughly rinse it under running
water. Place it back into Sponge Filter Inlet once it is COMPLETELY DRY (keeping
Sponge Filter dry will help prolong its lifetime).
6) Reassemble unit, and place Crevice Tool and Upholstery tool onto Accessory Holder by
sliding each one onto one of the holders two cylinders.
7) Loop Grounded Power Cord loosely around Power Cord Holders.
8) Store CenturionTM in a cool, dry location.
Top Innovations, Inc.
12
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
SOLUTION
Vacuum is not plugged
in.
Plug into electrical
outlet.
Unit fails to turn on.
Household Circuit
Breaker / Ground Fault
Interrupter has tripped or
blown a fuse.
Reset Circuit Breaker /
Ground Fault Interrupter,
or replace fuse. If you
need assistance, contact a
qualified electrician.
Unit turns on, but suction
is very weak or there is
no suction at all.
Hose, Removable
Suction Tube, or one of
the accessories has
become clogged.
Carefully inspect for any
blockages and remove
any you find.
Suction Power Control
on main unit or Main
Siphon is set to “low”.
Check that both Suction
Power Controls are set to
“high”.
ULTRA filter is no
longer functioning
efficiently.
Remove and clean
ULTRA filter, or replace
it with a new one.
There is water leakage
during wet vacuuming.
Float blocked and/or no
float filter.
Release float, clean
and/or dry foam filter.
CUSTOMER SUPPORT
For problems with your steam cleaner, refer to the Troubleshooting Guide located
above. Additional inquiries should be directed to our Customer Support services at
1-800-711-6617 ext. 102 / 130 or e-mailed to:
Should there be any missing or defective parts or accessories, contact Customer
Support. In most cases, it is not necessary to return the entire unit. We can ship
most parts directly to your door.
To ensure prompt and accurate service, call for a Return Authorization
number before returning any unit to Top Innovations. Failure to obtain a
Return Authorization number will cause a delay in warranty or out-of-
warranty service requests.
Top Innovations, Inc.
13
MODEL CF-980
C
ENTURIONTM WATER FILTRATION VACUUM
ACCESSORY ORDER FORM
PRICE
$12.99
$2.99
PART
PART DESCRIPTION
QTY.
TOTAL
A980-001
A980-002
A980-003
A980-004
A980-005
A980-006
A980-007
A980-008
Floor Brush
Sponge Filter
Telescopic Extension Tube
Hose
$12.99
$12.99
$5.99
Crevice Tool
Upholstery Tool
Main Siphon
$5.99
$5.99
ULTRA Filter
$5.99
Subtotal
+ S&H
Total USD
ORDER ONLINE TODAY
To try our convenient and totally secure
online ordering service, visit us at
$3.99
Method of Payment (no C.O.D. orders)
Check or Money Order (payable to Top Innovations)
Charge to my
VISA
MASTERCARD
ACCOUNT NUMBER
EXPIRATION DATE
TO ORDER:
ONLINE
Visit our website at
BY
MAIL
Fill out this form and
return to address on back
of this manual
SIGNATURE: ____________________________________________
(Full name as shown on account)
NAME: __________________________________________________
MAILING ADDRESS: _____________________________________
_________________________________________________________
TELEPHONE: ____________________________________________
B
Y
PHONE
(800) 711-6617
EXT. # 102/130
B
Y
FAX
(816) 584-9066
14
Top Innovations, Inc.
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations, Inc. warrants this product to be free from defects in material
and workmanship for a period of one (1) year from the date of purchase. This
warranty does not cover damage caused by misuse, negligence, use by
improper current or voltage, use contrary to operating instructions or
disassembly, repair or alteration by any person other than Top Innovations,
Inc. Warranty Service Department.
Top Innovations, Inc. will repair or replace, at its option. This warranty gives
you specific legal rights and may have other rights, which may vary from
state to state.
Performance of any obligation under this warranty may be obtained by:
1. Call (800) 711-6617 for Return Authorization Number before returning
for repair
2. Include copy of purchase receipt
3. Include your name, address, telephone number, and Return Authorization
Number on returned package
Please send product postage prepaid to:
TOP INNOVATIONS, INC.
WARRANTY SERVICE DEPARTMENT
400 NW PLATTE VALLEY DR.
RIVERSIDE, MO 64150
After 1 year limited warranty has expired, you will be advised of the cost of
repair before any servicing is done unless you enclose a note indicating that
you would like us to proceed with repairs.
If you have any questions about coverage under this warranty, you may
contact warranty service department by telephone at (800) 711-6617 ext. 102 /
130 or e-mail [email protected]
Top Innovations, Inc.
15
Top Innovations, Inc.
400 NW Platte Valley Dr.
Riverside, MO 64150
Tel: (800) 711-6617
Printed In China
|