13A25C
J3M13221A(E)_COVER
1
13/01/2005, 10:49 PM
Important Safety Instructions
Installation, Care, and Service
Installation
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
Follow these recommendations and precautions and heed
all warnings when installing your TV:
4) Follow all instructions.
16) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user’s authority to
operate this equipment under the rules of the Federal
Communications Commission.
5) Do not use this apparatus near
water.
17)
DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE! Never place the TV on
6) Clean only with a dry cloth.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
an unstable cart, stand, or table. The TV
may fall, causing serious personal injury,
death, or serious damage to the TV.
8) Do not install near any heat
sources such as radiators,
heat registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
18) Never place or store the TV in direct
sunlight; hot, humid areas; areas
subject to excessive dust or vibration;
or locations with temperatures at or
below 41°F (5°C).
9) Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding
19) Always place the TV on the floor
or a sturdy, level, stable surface that
can support the weight of the unit.
Wide plug
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician
for replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where it exits the apparatus.
20) Never place items such as vases,
aquariums, or candles on top of the TV.
11) Only use attachments/accessories specified by the
21) Never block or cover the slots or
openings in the TV cabinet back,
bottom, and sides. Never place
the TV:
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
• on a bed, sofa, rug, or similar
surface;
• too close to drapes, curtains,
or walls; or
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
• in a confined space such as a
bookcase, built-in cabinet, or any
other place with poor ventilation.
The slots and openings are provided
to protect the TV from overheating
and to help maintain reliable
operation of the TV.
13) Unplug this apparatus during
lightning storms or when
unused for long periods
of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply
cord or plug is damaged, liquid has
22) Never allow anything to rest on or roll over the power
cord, and never place the TV where the power cord is
subject to wear or abuse.
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
23) Never overload wall outlets and
extension cords.
15)
CAUTION: To reduce the risk of electric shock, do
not use the polarized plug with an extension cord,
receptacle, or other outlet unless the blades can be
inserted completely to prevent blade exposure.
0303
3
J3M13221A(E)_P02-07
3
13/01/2005, 10:50 PM
30) [This item applies to projection TVs only.] If the air
temperature rises suddenly (for example, when the TV
is first delivered), condensation may form on the lenses.
This can make the picture appear distorted or the color
appear faded. If this happens, turn off the TV for 6 to 7
hours to allow the condensation to evaporate.
24) Always operate this equipment from
a 120V AC, 60 Hz power source only.
25) Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see Section
810 of the National Electric Code).
31) For added protection of your TV from lightning and
power surges, always unplug the power cord and
disconnect the antenna from the TV if you leave the TV
unattended or unused for long periods of time.
Antenna lead-in wire
32) During normal use, the TV may make
occasional snapping or popping
Antenna discharge unit
(NEC Section 810-20)
Ground clamp
sounds. This is normal, especially
when the unit is being turned on or
off. If these sounds become frequent
or continuous, unplug the power cord
and contact a Toshiba Authorized Service Center.
Grounding conductors
(NEC Section 810-21)
Electric service equipment
Power service grounding
electrode system (NEC Art 250 Part H)
Ground clamps
33) Possible Adverse Effects on TV Picture Tube: If a
fixed (non-moving) pattern remains on the TV screen
for long periods of time, the image can become
permanently ingrained in the picture tube and cause
subtle but permanent ghost images. This type of
damage is NOT COVERED BY YOUR WARRANTY.
Never leave your TV on for long periods of time while it
is displaying the following formats or images:
26)
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
• Use extreme care to make sure you are never
in a position where your body (or any item you are in
contact with, such as a ladder or screwdriver) can
accidentally touch overhead power lines. Never locate
the antenna near overhead power lines or other
electrical circuits.
• Fixed Images, such as PIP/POP windows, stock
tickers, video game patterns, TV station logos, closed
captions, and websites.
• Never attempt to install any of the following during
lightning activity:
• Special Formats that do not use the entire screen.
For example, viewing letterbox style (16:9) media on a
normal (4:3) display (gray bars at top and bottom of
screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (gray bars on left and right
sides of screen).
a) an antenna system; or b) cables, wires, or any home
theater component connected to an antenna or phone
system.
Care
For better performance and safer operation of your
TOSHIBA TV, follow these recommendations and
precautions:
Service
34)
WARNING: RISK OF ELECTRIC
SHOCK! Never attempt to service the
TV yourself. Opening and
27) Always sit approximately 10–25 feet away from the TV
and as directly in front of it as possible. The picture can
appear dull if you sit too far to the left or right of the TV,
or if sunlight or room lights reflect on the screen. Turn
the TV off to check for reflections on the screen, and
then remove the source of reflections while viewing the
TV.
removing the covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to a
Toshiba Authorized Service Center.
35) If you have the TV serviced:
• Ask the service technician to use only replacement
parts specified by the manufacturer.
28) Always unplug the TV before
cleaning. Never use liquid or
aerosol cleaners.
• Upon completion of service, ask
the service technician to perform
routine safety checks to determine
that the TV is in safe operating
condition.
36) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of the
TV. Improper disposal may result in a picture tube
implosion and possible personal injury.
29)
WARNING: RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind
into the TV cabinet slots.
0303
4
J3M13221A(E)_P02-07
4
13/01/2005, 10:51 PM
FEATURES
• 181 Channel Tuner - The tuning system is capable of receiving all 68 VHF/UHF standard broadcast channels that
are available in your area. When operating on a cable system, it can tune to the standard VHF channel frequencies
plus up to 113 cable channel frequencies. The actual number of channels received depends upon channel
reception in your area or your cable system.
• On-screen 3 Language Display - This TV can display the on-screen language in English, Spanish or French.
• Sleep Timer - Operable from the remote control, the TV can be programmed to turn off automatically (from 10 to
120 minutes, in 10-minute increments).
• Memory Back Up - This system prevents loss of memorized channel selections in case a power interruption to the
TV should occur.
• Picture Control Adjustments - The on-screen display allows precise remote control adjustment of BRIGHTNESS,
CONTRAST, COLOR, TINT and SHARPNESS.
• Closed Captioned Decoder - Displays closed captions or text on-screen (when available).
• Lock feature - This feature has three functions, LOCKING CHANNELS, LOCKING VIDEO INPUT and SETTING
THE GameTimerTM.
• Programmable ON Timer - Allows you to program the TV to automatically turn on at a set time.
LOCATION OF CONTROLS
FRONT
BACK
ANT
8
9
PHONE
POWER
VOLUME
CHANNEL
VIDEO AUDIO
SET
MENU
ENTER RESET
1 2 3
4
5
6
7
6. CHANNEL L/M Buttons - Press to select a higher or
lower numbered channel set into memory.
(ENTER Button) - Press to enter or select information
for on-screen operations.
(RESET Button) - Press, while in the on-screen
menu mode, to reset the on-screen picture adjust-
ments to their factory preset positions.
7. AUDIO/VIDEO IN Jacks - Audio and video signal
cables from an external source can be connected
here.
1. PHONE (Earphone) Jack - Plug an earphone or
monaural headphones with a 1/8” miniplug into this
jack for private listening.
2. POWER indicator - Lights up when the power is
turned on.
3. Remote Sensor - Signals from the Remote Control
unit are received here.
4. POWER Button - Press to turn the TV on or off.
5. VOLUME L/M Buttons - Press to raise or lower the
level of the sound.
8. AC Power Cord - Plug into an outlet with 120V,
60 Hz AC power only.
9. VHF/UHF IN (ANT) Jack - Connect a VHF/UHF
antenna or Cable TV 75 ohm coaxial cable to this
jack.
(MENU Buttons) - Press both VOLUME L/M buttons
at the same time to display the on-screen menu functions.
(SET + / – Buttons) - Press to select the desired set-
ting during on-screen operations.
5
J3M13221A(E)_P02-07
5
13/01/2005, 10:51 PM
REMOTE CONTROL
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button on the remote
control. The clock will count down 10 minutes each time
the button is pressed in the order of 120, 110, 100, ······ 20,
10, 0. After the sleep time is programmed, the display will
disappear then reappear momentarily every ten minutes to
remind you the sleep timer function is operating. To
confirm the sleep time setting, press the SLEEP button
once and the remaining time will be momentarily displayed.
To cancel the sleep timer, press the SLEEP button
repeatedly until the display turns to 0.
POWER
1
1
4
7
0
2
5
8
3
6
2
3
9
10
11
CH RTN
RECALL
5. VOL (VOLUME) + / – Buttons - Press the + button to
increase or the – button to decrease the volume level.
6. MENU Button - Press to display the on-screen menu
function.
SLEEP
MUTE
4
5
CH +
7. SET + / – Buttons - Press to select the desired setting
during on-screen operations.
8. RESET Button - Press to reset the on-screen picture
adjustments to their factory preset positions.
9. TV/VIDEO Button - Switches between the TV and external
device inputs.
VOL
–
VOL
+
12
13
MENU
ENTER
CH –
SET
6
7
–
+
10. RECALL Button - When you press this button, the
channel number will appear in the upper right corner of the
screen. Press the button again to remove it from the
screen.
11. MUTE Button - To turn off the sound, press this button
once. The TV will be silenced and the word “MUTE” will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL + or
– buttons.
RESET
8
9
14
15
CAP/TEXT
TV/VIDEO
1/2
CT-859
12. CH (CHANNEL) + / – Buttons - Press the CH + button to
change to a higher numbered channel set into memory.
Press the CH – button to change to a lower numbered
channel set into memory.
13. ENTER Button - Press to enter or select information for
on-screen operations.
1. POWER Button - Press to turn on the TV. Press again
to turn off the TV.
2. Direct Channel Selection Buttons (0–9) - Allows direct
tuning of any channel.
3. CH RTN Button - Repeatedly press CH RTN to toggle
back and forth between the last two channels you tuned.
14. 1/2 Button - Switches between captions channel 1 and
captions channel 2 in the closed caption mode.
15. CAP/TEXT Button - Press to switch between normal TV
and the two closed caption modes (captions or text), when
available.
Before using the remote control, batteries must first be installed.
HOW TO INSTALL BATTERIES
1. Open the battery compartment cover.
Use two “AAA” size penlight batteries (supplied) for the
remote control. The batteries may last approximately one
year depending on how much the remote control is used.
For best performance, it is recommended that you replace
the batteries on a yearly basis or when the remote operation
becomes erratic.
Caution:
•
Never throw batteries into a fire.
Note :
•
•
•
Be sure to use AAA size batteries.
Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects
of battery disposal.
2. Install two “AAA” (penlight size) batteries.
•
•
Do not mix different battery types or combine used
batteries with new ones.
If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both
batteries with new ones.
•
If the batteries are dead or if you will not be using the
remote control for a long time, remove the batteries to
prevent battery acid from leaking into the battery
compartment.
3. Replace the battery compartment cover.
6
J3M13221A(E)_P02-07
6
13/01/2005, 10:51 PM
ANTENNA/CABLE TV CONNECTIONS
Combination VHF/UHF antenna (Single 75 ohm cable or 300
Choose one of the following seven connections, based on your
equipment and service:
ohm twin-lead wire)
Connect the 75 ohm cable from a combination VHF/UHF
antenna to the antenna jack.
If your combination antenna has a 300 ohm twin-lead wire, use
the 300-75 ohm matching transformer (not supplied).
Combination VHF/UHF antenna
To ANT input
on back of TV
Single 75 ohm cable
Combination VHF/UHF antenna (Separate VHF and UHF 300
ohm twin-leads)
(or)
To ANT input
Connect the UHF twin-lead wire to a combiner (not supplied).
Connect the VHF twin-lead to the 300-75 ohm matching
transformer (not supplied). Attach the transformer to the
combiner. Attach the combiner to the antenna jack.
Single 300 ohm twin-lead wire*
on back of TV
For best performance, if you have a splitter connected, remove
the splitter and connect the single wire to the transformer,
and then to the TV’s antenna input (as illustrated here).
TRANSFORMER
(not supplied)
*
Separate VHF/UHF antennas
Connect the 75 ohm cable from the VHF antenna and the UHF
antenna twin-lead to a combiner (not supplied). Attach the
combiner to the antenna jack.
Separate VHF and UHF antennas or
Combination VHF/UHF antenna with separate cables/wires
NOTE: If your VHF antenna has a twin-lead wire, use the 300-75
ohm matching transformer (not supplied), then connect the trans-
former to the combiner.
UHF Antenna
300 ohm twin-lead wire
To ANT input
on back of TV
For subscribers to basic cable TV service
For basic cable service not requiring a converter/descrambler
box, connect the Cable TV 75 ohm coaxial cable directly to the
antenna jack on the back of the television.
VHF Antenna
COMBINER
(not supplied)
75 ohm cable
For subscribers to scrambled cable TV service
If you subscribe to a cable service that requires the use of a
converter/descrambler box, connect the incoming cable to the
converter/descrambler box and connect the output of the box to
the antenna jack on the back of the television. Follow the
connections shown at left. Set the television to the output of the
converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to select channels.
(or)
UHF Antenna
300 ohm twin-lead wire
To ANT input
on back of TV
VHF Antenna 300 ohm twin-lead wire*
COMBINER
For subscribers to unscrambled basic cable with scrambled
premium channels
(not supplied)
TRANSFORMER
(not supplied)
If you subscribe to a cable service in which basic cable channels
are unscrambled and premium channels require the use of a
converter/descrambler box, you may wish to use a two-set signal
To ANT input
on back of TV
Cable TV service
splitter (sometimes called a “two-set coupler”) and an A/B switch
From cable
box from the cable installer or an electronics supply store. Follow
the connections shown at left. With the switch in the position,
you can directly tune any nonscrambled channels on your TV.
TV service
“B”
To ANT input
on back of TV
(or)
From cable
TV service
With the switch in the
“
A
”
position, tune your TV to the output of the
CONVERTER/ DESCRAMBLER
CONVERTER/ DESCRAMBLER
converter/descrambler box (usually channel 3 or 4) and use the
box to tune scrambled channels.
To ANT input
on back of TV
(or)
From cable
TV service
This television has an extended tuning range and can tune most
cable channels without using a cable company supplied
A
SPLITTER
A / B SWITCH
B
converter box. Some cable companies offer “premium pay
channels in which the signal is scrambled. Descrambling these
”
signals for normal viewing requires the use of a descrambler
device, which is generally provided by the cable company.
CONNECTION TO OTHER EQUIPMENT
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features
of each component. Check the owner’s manual provided with each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. You may need to modify them to accommodate your particular
assortment of components.
2. To connect the TV to a VIDEO Game
TV/VIDEO SELECTION
To view the picture from a VCR,
The TV also can be used as a display device for many video
games. However, due to the wide variety of different types of
signal generated by these devices and subsequent hook-up
variations required, they have not all been included in the
suggested connection diagrams. You will need to consult each
component's owner's manual for additional information.
VIDEO
camcorder, or TV game, you must put the
TV in VIDEO mode first. Press TV/VIDEO
to select VIDEO mode. The word “VIDEO”
displays briefly on-screen. Press TV/VIDEO
again to return to TV mode.
Front of TV
1. To connect the TV to a VCR
VIDEO AUDIO
VCR
VIDEO Game
Front of TV
RESET
VIDEO AUDIO
RESET
To Audio/Video OUT
(not supplied)
To Audio/
Video OUT
VIDEO
AUDIO
(not supplied)
3. To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder to
The unauthorized recording, use, distribution, or
the TV as shown.
Front of TV
revision of television programs, videotapes, DVDs, and
other materials is prohibited under the Copyright Laws
of the United States and other countries, and may
subject you to civil and criminal liability.
VIDEO AUDIO
RESET
To AV OUT jack
(not supplied)
7
J3M13221A(E)_P02-07
7
13/01/2005, 10:52 PM
SETTING THE LANGUAGE
This TV can display the on-screen displays and adjustment menus in English, Spanish, or French.
The on-screen language selection (step 3, below) will automatically appear on the screen when you press the MENU button
initially. Select the language you prefer first, then proceed with the other menu options.
Press SET + or – until the
“
”
Press MENU.
3
1
2
LANGUAGE / IDIOMA / LANGUE
ENGLISH
indicator points to the desired
language: English (ENGLISH),
Spanish (ESPAÑOL) or French
(FRANCAIS), then press ENTER.
ESPAÑOL
Press SET + or – to select the
LANGUAGE mode, then press
ENTER.
FRANCAIS
⟨
⟩
⟨
+
–
⟩
/
/
ENTER MENU
/
Press MENU repeatedly until the
menu screen is cleared.
4
NOTE:
If Spanish or French is chosen, the closed caption indicators will be in the selected language, but the closed caption text
will not be affected by the language selection.
TV OPERATION
DIRECT CHANNEL SELECTION buttons (0–9) - Press
1
2
To turn on the TV, press POWER.
these buttons to select a channel. The channel number will
appear on the upper right corner of the TV screen. If an
invalid channel number is selected, the display will revert to
the previous channel.
The VOLUME can be adjusted to a desired level by
pressing VOL (VOLUME) + or –.
The sound level will be indicated on the TV screen by
GREEN BARS AND A NUMBER. As the sound level
increases, so do the number of BARS AND THE
NUMBER on the screen. The same is true for decreas-
ing the level.
TV MODE DIRECT CHANNEL SELECTION - When the
TV/CABLE menu option is in the TV position, all channels
can be instantly selected by using two buttons (For example,
to select channel 2, press “0,” then “2.” If you press only “2,”
channel selection will be delayed for a few seconds). For
channels 10 and above, press the two digits in order.
Set the TV/CABLE menu option to the appropriate
position. When shipped from the factory, this menu
3
4
option is in the CABLE setting. See “TO MEMORIZE
CHANNELS” on page 9.
CABLE mode direct channel selection
When the TV/CABLE menu option is in the CABLE position,
channels can be selected as follows:
TV - VHF/UHF channels
CABLE - CABLE TV channels
1-9
Press “0” twice, then 1-9 as needed.
Example, to select channel 2, press
“002.”
CH (CHANNEL) + and – buttons
10-12
13-99
100-125
Press “0”, then the remaining 2 digits.
Example, to select channel 12, press
“012.”
Press the 2 digits in order.
Example, to select channel 36, press
“36.”
Press the 3 digits in order.
Example, to select channel 120, press
“120.”
Press and release CH (CHANNEL) + or –. The
channel automatically stops at the next channel
programmed into the TV’s memory. Press and hold the
button down to change channels more quickly.
For proper operation, make sure you program
channels into the TV’s memory before tuning
channels. See “TO MEMORIZE CHANNELS” on page 9.
NOTE: If the station being viewed stops broadcasting, the TV
will automatically shut off after 15 minutes.
8
J3M13221A(E)_P08-12
8
13/01/2005, 10:52 PM
TO MEMORIZE CHANNELS
This TV is equipped with a channel memory feature that allows the
TV to skip up or down to the next channel set into memory, skip-
ping over unwanted channels.
TO ADD/DELETE CHANNELS
Press MENU.
1
Before selecting channels, they must be programmed into the TV’s
memory. In addition to normal VHF and UHF channels, this TV can
receive up to 113 Cable TV channels. To use this TV with an
antenna, set the TV/CABLE menu option to the TV setting. When
shipped from the factory, this menu option is in the CABLE setting.
Press SET + or –until the indicator next to
“CH SETUP” begins to flash, then press
ENTER.
2
⟨
⟩
Press SET + or – until the indicator
next to “ADD/DELETE” begins to
3
TV/CABLE SELECTION
TV
CABLE
flash, then press ENTER.
Press MENU.
AUTO CH MEMORY
ADD / DELETE
1
Select the desired channels to be
Press SET + or – until the indicator next to
2
4
⟨
+
–
⟩
/
/ ENTER / MENU
“CH SETUP” begins to flash, then press
added or deleted using the Direct
Channel Selection buttons (0–9), CH +
or –, SET + or –.
ENTER.
⟨
⟩
Press SET + or – until the indicator next
to “TV/CABLE” begins to flash.
3
4
Press ENTER to select ADD or DELETE.
5
TV
CABLE
If an unmemorized channel was selected (step 4), the
channel indication will be red. Press ENTER if you wish
to ADD the unmemorized channel. The channel indica-
tor will change from red to green when a channel is
added and the channel will be memorized.
AUTO CH MEMORY
ADD / DELETE
Press ENTER to select the TV or CABLE
mode. The arrow indicates the selected
mode.
⟨
+
–
⟩
/
/ ENTER / MENU
Press MENU repeatedly until the menu
screen is cleared.
5
NOTE:
If a memorized channel was selected (step 4), the chan-
nel indication will be green. To delete the channel from
memory, press ENTER repeatedly until
Contact your cable company to determine the type of cable
system used in your area.
ADD
CH 012
AUTOMATIC CHANNEL MEMORY
“DEL” appears on-screen. The channel
indicator will change from green to red
when a channel is deleted. Repeat
steps 4 and 5 for each channel to be
added or deleted.
Press MENU.
1
⟨
⟩
0 – 9 / + / – / ENTER / MENU
Press SET + or –until the indicator next to
“CH SETUP” begins to flash, then press
2
ENTER.
⟨
⟩
Press MENU repeatedly until the menu screen is
cleared.
6
Press SET + or – until the indicator next
3
TV
CABLE
to “AUTO CH MEMORY” begins to flash,
then press ENTER. The TV will begin
memorizing all the channels available in
your area. Channel numbers will remain
red until auto memorizing is complete.
AUTO CH MEMORY
ADD / DELETE
⟨
+
–
⟩
/
/ ENTER / MENU
Press MENU repeatedly until the menu screen is
cleared.
4
ADJUSTING THE PICTURE
You can adjust the settings for brightness, contrast, color,
tint and sharpness.
Press SET + or – to adjust the setting.
4
+
–
Press MENU.
1
BRIGHTNESS
higher
lower
CONTRAST
COLOR
lighter
darker
paler
Press SET + or – until the indicator next to “PICTURE”
begins to flash, then press ENTER.
2
deeper
greenish
sharper
reddish
softer
TINT
SHARPNESS
Press ENTER repeatedly to select the item you want to
adjust.
3
TO RETURN TO INITIAL SETTING:
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
Press RESET while the picture adjusting mode appears
on-screen.
9
J3M13221A(E)_P08-12
9
13/01/2005, 10:52 PM
CLOSED CAPTION
WHAT IS CLOSED CAPTIONING?
Text: When available, the Text mode will fill part of the screen with a
This television has the capability to decode and display closed
captioned television programs. When available, closed captioning will
display text on the screen for hearing impaired viewers or it will
translate and display text in another language.
programming schedule or other information.
After selecting a closed caption mode, it will stay in effect until it is
changed, even if the channel is changed. If the captions signal is lost
due to a commercial or a break in the signal, the captions will reappear
when the signal is received again. If the channels are changed, the
captions will be delayed approximately 10 seconds.
For television programs broadcasting with closed captions, look in your
TV guide for the closed captions symbol (CC).
TO VIEW CLOSED CAPTIONS
Press CAP/TEXT on the remote control to switch between normal TV
and the two closed caption modes (captions and half-screen Text).
Captions: This closed caption mode will display text on the screen in
English or another language (depending on the setting of Closed
Captions 1/2). Generally, closed captions in English are transmitted
on captions channel 1 and closed captions in other languages are
transmitted on captions channel 2.
The captions will appear in places on the screen where they will least
interfere with the picture, usually on the bottom of the screen. News
programs will usually show three-line closed captions that scroll onto
the screen. Most other shows provide two- or three-line captions
placed near the character who is speaking so the viewer can follow the
dialogue. Words in italics or underlined describe titles, words in foreign
languages or words requiring emphasis. Words that are sung usually
appear enclosed by musical notes.
NOTICE OF POSSIBLE ADVERSE EFFECTS ON TV PICTURE TUBE
Avoid displaying stationary images on your TV screen for extended
periods of time. Fixed (non-moving) images (such as closed captions)
can become permanently ingrained in the picture tube. This type of
damage is NOT COVERED BY YOUR WARRANTY.
• When activating the closed captioned decoder, there will be a short delay before the closed captioned text appears on the screen.
• Closed captioned text is only displayed in locations where it is available.
• If no caption signal is received, no captions will appear, but the television will remain in the caption mode.
• Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with closed captioning, especially with live
programs. This is because during live programs, captions are also entered live. These transmissions do not allow time for editing.
• When captions are being displayed, on-screen displays such as volume and mute may not be seen or may interfere with closed captions.
• Some cable systems and copy protection systems may interfere with the closed captioned signal.
• If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with strange characters or
misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna.
TO SET THE ON TIMER
This feature allows you to program the TV to turn on automatically at a set time and channel.
NOTE: After a power failure or disconnection of the power, the timer setting will be lost.
ON TIMER
4
ON TIMER
HOUR
MINUTE
CH 125
Press MENU, then press SET + or – until
the indicator next to “ON TIMER” begins
to flash. Then press ENTER.
Press SET + or – to set the desired
channel, then press ENTER.
1
HOUR
MINUTE
CH 002
00h
00m
CANCEL
08h
15m
SET
The ON TIMER menu appears.
⟨
+
—
⟩
/
/ ENTER / MENU
⟨
+
—
⟩
/
/ ENTER / MENU
Press SET + or – to set the desired hour (0–12), then
Press SET + or – to select the SET mode, then press ENTER.
5
6
2
3
press ENTER.
Press MENU repeatedly until the menu screen is cleared.
Press SET + or – to set the desired minute
(00, 05, 10, ...55), then press ENTER.
NOTE:
To cancel the ON TIMER, select CANCEL in step 5 above. Press
MENU repeatedly until the menu screen is cleared.
10
J3M13221A(E)_P08-12
10
15/01/2005, 2:02 AM
USING THE LOCK MENU
The LOCK menu includes the CH LOCK, VIDEO LOCK, GAMETIMER and CHANGE PASSWORD functions.
You can use these functions after entering the correct PASSWORD.
TO REGISTER PASSWORD
Press MENU and then SET + or – until the indicator next
NOTES:
1
2
to “LOCK” begins to flash, then press ENTER.
• If you want to change your password, follow steps 1 and 2 and
select “CHANGE PASSWORD” option. Then enter your new
password.
Enter your password (4 digits) using the Direct channel
selection buttons (0–9).
In the event of entering an incorrect password press
RESET. Then press ENTER.
• If you forget or lose your password, you can reset it using the
following procedure:
- While holding down the VOLUME 4 button on the TV, press
“0” on the remote control for a few seconds.
Enter the password again, and then press ENTER.
The password is now registered and the LOCK menu
appears.
3
LOCKING CHANNELS
With the CH LOCK feature, you can lock specific channels. You will not be able to tune locked channels unless you clear the setting.
You can choose to lock up to nine TV channels and nine cable channels.
Repeat steps 1 through 5 to lock other channels. When you
are finished locking channels, press MENU repeatedly until
the menu screen is cleared.
Use the Channel Number buttons (0–9) to display the
1
2
3
6
television channel you wish to lock.
Press MENU, then press SET + or – until the indicator
next to “LOCK” begins to flash. Then press ENTER.
If you try to tune a locked channel, the TV will not display it, but
will display the nearest unlocked channel.
Use the Channel Number buttons (0–9) to enter your
password, then press ENTER.
The LOCK menu appears.
NOTES:
LOCK
CH LOCK
VIDEO LOCK
• If you are accessing the LOCK menus for the first time,
choose a four-digit number to be your password.
GAME TIMER
CHANGE PASSWORD
Press SET + or – until the indicator next
4
5
• After programming CH LOCK, change channels before
to “CH LOCK” begins to flash, then
turning off the television.
+
⟩
/ ENTER / MENU
press ENTER.
⟨
–
/
• If you want to unlock channels, select ALL CLEAR in step 5,
then press ENTER.
Press SET + or – to select:
CH LOCK
CABLE
• INPUT to select the channel as one to
be locked. Then press ENTER.
• ALL CLEAR to clear all channels from
the list of locked channels. Then press
ENTER.
INPUT
--- --- ---
--- --- ---
--- --- ---
ALL CLEAR
⟨
+
–
⟩
/ ENTER / MENU
/
LOCKING VIDEO INPUT
SETTING THE GameTimer™
With the VIDEO LOCK feature, you can lock out the input
With the GameTimer™ feature, you can automatically activate
the VIDEO LOCK feature (VIDEO setting) to set a time limit for
playing a TV game (30, 60, 90, or 120 minutes).
source (VIDEO) and channels 3 and 4. You will not be able to
select the input sources with the TV/VIDEO button or Channel
buttons unless you clear the setting.
Press MENU, then press SET + or – until the indicator next to
“LOCK” begins to flash, then press ENTER.
1
Press MENU, then press SET + or – until the indicator
next to “LOCK” begins to flash, then press ENTER.
1
Use the Channel Number buttons (0–9) to enter your pass-
word, then press ENTER. The LOCK menu appears.
Use the Channel Number buttons (0–9) to enter your
password, then press ENTER. The LOCK menu appears.
2
2
Press SET + or – until the indicator next
3
Press SET + or – until the indicator
next to “VIDEO LOCK” begins to flash,
then press ENTER.
VIDEO LOCK
OFF
to “GAMETIMER” begins to flash, then
3
4
press ENTER.
VIDEO
VIDEO+
Press SET + or – to select a time limit
(30 minutes, 60 minutes, 90 minutes,
120 minutes or OFF).
4
⟨
⟩
Press SET + or – to select:
⟨
+
–
⟩
/
/ ENTER / MENU
• OFF: Unlocks all video input sources.
• VIDEO: Locks VIDEO.
• VIDEO +: Locks VIDEO, channel 3 and channel 4.
This option should be used if you use the antenna
to play a video tape.
Press MENU repeatedly until the menu screen is cleared.
After the GameTimer is programmed, the display will
appear briefly every ten minutes to remind you that the
GameTimer is operating. When the programmed end time
is reached, the display will change the channel
automatically.
5
Press MENU repeatedly until the menu screen is cleared.
5
NOTE:
NOTE:
After programming VIDEO LOCK, change channels or press the
TV/VIDEO key before turning off the television.
When the programmed end time is reached, the TV will change
channels automatically and the VIDEO LOCK feature will be
activated. To turn off the VIDEO LOCK, see “LOCKING VIDEO
INPUT,” at left.
11
J3M13221A(E)_P08-12
11
15/01/2005, 2:02 AM
TROUBLESHOOTING GUIDE
Before requesting service, please refer to the following chart for the symptom and possible solution.
SYMPTOMS
POSSIBLE SOLUTIONS
SYMPTOMS
POSSIBLE SOLUTIONS
• Check all Cable TV connections.
• Set TV/CABLE menu option to the CABLE
mode.
• Station or Cable TV system problems; try
another station or call your Cable company.
• Make sure the power cord is plugged in.
TV does not • Try another AC outlet.
No Cable TV
reception.
operate.
• Power is off; check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Station or Cable TV experiencing problems;
tune to another station or call your Cable company.
• Check sound adjustments (VOLUME and
MUTE).
Horizontal or
diagonal bars
on screen.
• Check antenna connections; reorient antenna.
• Check for sources of possible interference.
Poor sound
or no sound.
• Make sure TV/CABLE menu option is in the
appropriate mode.
• If using antenna, check UHF antenna
connections.
• Check for sources of possible interference.
No reception
above
channel 13.
• Station or Cable TV experiencing problems;
tune to another station or call your Cable company.
• Make sure channels are set into memory.
• Check antenna or Cable TV connections;
adjust antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
• Press CAP/TEXT to turn off the closed
caption mode.
• Batteries are weak, dead or inserted
incorrectly.
• Remote is out of range; move closer to TV
(within 15 feet).
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between
the Remote and the TV.
Poor picture
or no picture.
No Remote
operation.
• Make sure the power cord is plugged in.
• Station or Cable TV experiencing problems;
tune to another station or call your Cable company.
• Make sure channels are set into memory.
• Station is weak; adjust antenna to receive
desired station.
Poor
reception on
some
• Tuned station is not broadcasting.
• Sleep Timer is set.
• Power interrupted.
TV shuts off.
channels.
• Check for sources of possible interference.
• TV station experiencing problems or tuned
program is not closed captioned. Try another
channel.
• Check Cable TV connection or VHF/UHF
antenna. Reposition or rotate antenna.
• Press CAP/TEXT to turn on the closed caption
decoder.
• Station or Cable TV experiencing problems;
tune to another station or call your Cable company.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or Cable TV connection.
Adjust antenna.
Closed
captions are
not activated.
Poor color or
no color.
Black box on
screen.
• Press CAP/TEXT to turn off the closed
caption mode.
• Station or Cable TV experiencing problems;
tune to another station or call your Cable company.
• Make sure channels are set into memory.
• Cable TV company is scrambling signal.
• Adjust antenna.
Picture
wobbles or
drifts.
Display is not
shown in
your language.
• Select the language in the menu options.
SPECIFICATIONS
• This model complies with the specifications below.
• Design and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
AC Power Input:
AC Power Consumption:
Picture Tube:
Audio Power Output Rating:
Speaker:
Tuner Type:
120V, 60Hz
54 Watts
13 Inch (335mm diagonal) (Screen size is approximate.)
1.0 Watts
3 inches (76mm) Full Range, 8 ohm
181 Channel, Quartz PLL Frequency Synthesized
Infrared, Direct Access, two AAA batteries (supplied)
Remote Control:
Receiving Channels:
VHF
UHF
2-13
14-69
Cable TV 01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
Antenna Input Impedance:
Input:
75 Ohm (VHF/UHF) Coaxial Input
Video: 1.0 Vp-p 75 ohm
Audio: 300 mV, 47k ohm
Width: 14-1/4 inches (362mm)
Height: 12-5/8 inches (320.5mm)
Depth: 14-3/16 inches (360mm)
20.9 Ibs (9.5 kg)
Dimensions:
Weight:
ACCESSORY
Remote Control with two size “AAA” batteries
12
J3M13221A(E)_P08-12
12
13/01/2005, 10:53 PM
Limited Canada Warranty
for 27'’ and All Smaller Television Models
Toshiba of Canada Limited (“TCL”) makes the following limited
Your Responsibility
warranties to original consumers in Canada. THESE LIMITED
WARRANTIES EXTEND TO THE ORIGINAL CONSUMER
PURCHASER OR ANY PERSON RECEIVING THIS TELEVISION AS A
GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO
OTHER PURCHASER OR TRANSFEREE.
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this television must be performed by an
Authorized TCL Service Depot.
(3) These warranties from TCL are effective only if the television is
purchased in Canada from an authorized TCL dealer and
operated in Canada.
(4) Labor charges for installation, setup, adjustment of customer
controls, and installation or repair of antenna systems are not
covered by these warranties. Reception problems caused by
inadequate antenna systems are your responsibility.
PRODUCTS PURCHASED IN CANADA AND USED ANYWHERE
OUTSIDE OF CANADA, INCLUDING, WITHOUT LIMITATION, THE
U.S.A. AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
PRODUCTS PURCHASED ANYWHERE OUTSIDE OF CANADA,
INCLUDING, WITHOUT LIMITATION, THE U.S.A. AND MEXICO,
AND USED IN CANADA, ARE NOT COVERED BY THESE WARRANTIES.
(5) Warranties extend only to defects in materials or workmanship
as limited above and do not extend to any television or parts that
have been lost or discarded by you or to damage to television or
parts caused by fires, misuse, accident, Acts of God (such as
lightning or fluctuations in electric power), improper installation,
improper maintenance, or use in violation of instructions
Limited One (1) Year Warranty on Parts and Labor*
TCL warrants this television and its parts against defects in materials
or workmanship for a period of one (1) year after the date of original
retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW
OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS
OR LABOR. YOU MUST DELIVER THE ENTIRE TELEVISION TO
AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE SERVICE DEPOT.
furnished by TCL; or to units that have been modified or had the
serial number removed, altered, defaced, or rendered illegible.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and
checking the “Troubleshooting” section, you find that service is needed:
(1) To find the nearest TCL Authorized Service Depot, visit TCL’s web site
Limited Two (2) Year Warranty on Picture Tube*
TCL further warrants the picture tube in this television against defects
in materials or workmanship for a period of two (2) years after the
date of original retail purchase. DURING THIS PERIOD, TCL WILL,
AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE
TUBE WITH A NEW OR REFURBISHED PICTURE TUBE WITHOUT
CHARGE TO YOU, EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE
IS REPAIRED OR REPLACED AFTER ONE (1) YEAR FROM THE
DATE OF THE ORIGINAL RETAIL PURCHASE, YOU MUST PAY
ALL LABOR CHARGES INVOLVED IN THE REPAIR OR
REPLACEMENT. YOU MUST DELIVER THE ENTIRE TELEVISION
TO AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR
ALL TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE SERVICE DEPOT.
(2) Present your bill of sale or other proof of purchase to the Authorized
Service Depot. You must deliver the entire television to an Authorized
TCL Service Depot. You must pay for all transportation and insurance
charges for the television to and from the Service Depot.
For additional information,
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF
CANADA, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF
CANADA AS HEREBY LIMITED, THE FOREGOING WARRANTY IS
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS OF
TCL WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY
PARTS. IN NO EVENT SHALL TCL BE LIABLE FOR
Rental Units
The warranty for rental units begins with the first rental or thirty (30)
days from the date of shipment to the rental firm, whichever comes first.
CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, OR
MODIFICATION OR ERASURE OF RECORDED DATA CAUSED BY
USE, MISUSE, OR INABILITY TO USE THIS PRODUCT).
*Limited Warranty for Commercial Units
TCL warrants televisions sold and used for commercial purposes as
follows: all parts are warranted against defects in materials or
workmanship for a period of ninety (90) days after the date of original
purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S OPTION,
REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS
OR LABOR. YOU MUST DELIVER THE ENTIRE TELEVISION TO
AN AUTHORIZED TCL SERVICE DEPOT. YOU MUST PAY FOR
ALL TRANSPORTATION AND INSURANCE CHARGES FOR THE
TELEVISION TO AND FROM THE SERVICE DEPOT.
No person, agent, distributor, dealer, or company is authorized to
change, modify, or extend the terms of these warranties in any manner
whatsoever. The time within which action must be commenced to
enforce any obligation of TCL arising under this warranty or under any
law of Canada or of any province thereof is hereby limited to 90 days
from the date you discover, or should have discovered, the defect. This
limitation does not apply to implied warranties arising under the law of
any province of Canada.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY
FROM PROVINCE TO PROVINCE IN CANADA. SOME
PROVINCES OF CANADA DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, WHEN AN
ACTION MAY BE BROUGHT, OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT
APPLY TO YOU UNDER SUCH CIRCUMSTANCES.
Owner’s Manual and Product Registration
Read this owner’s manual thoroughly before operating this television.
By registering your product, you will enable TCL to bring you new
products specifically designed to meet your needs and help us to
contact you in the unlikely event a safety notification is required
under the U.S. Consumer Product Safety Act. Failure to register your
product does not diminish your warranty rights.
FST PURE¨ is a registered trademark of Toshiba America Consumer
Products, L.L.C.
[011005]
13
J3M13221A(E)_P13-BACK
13
13/01/2005, 10:54 PM
TEL.: (905) 470-5400
Service Centers:
TORONTO: 191 McNABB STREET,
MARKHAM, ONTARIO, L3R 8H2, CANADA
TEL.: (905) 470-5400
MONTREAL: 18050 TRANS CANADA, KIRKLAND,
QUEBEC, H9J-4A1, CANADA
TEL.: (514) 390-7766
VANCOUVER: 22171 FRASERWOOD WAY,
RICHMOND, B.C., V62 1J5, CANADA
TEL.: (604) 303-2500
GameTimer is a trademark of Toshiba America Consumer Products, L.L.C.
FST PURE® is a registered trademark of Toshiba America Consumer Products, L.L.C.
PRINTED IN THAILAND
J3M13221A(E)_P13-BACK
14
13/01/2005, 10:54 PM
|