Tripp Lite World Headquarters
1111 W. 35th Street, Chicago, IL 60609 USA
User’s Manual
KVM CONSOLE EXTENDER
Model #: B013-000
NOTE: Follow these installation and operating procedures to ensure correct performance and to prevent
damage to this unit or to its connected devices.
Copyright © 2000 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
Technical specifications are subject to change without notice.
Features
Uses Inexpensive, Reliable, Category 5 STP Ethernet Cable to
Connect the Local and Remote Units
Dual Console Operation - Control Your System From Both the
Local and Remote PS/2 Keyboard, Mouse, and Monitor Consoles
Push Button Selection of the Active Console
High Resolution Video - Up To 1024 x 768 @ 150 m (max.)
Supports VGA, SVGA, and Multisync Monitors
Local Monitor Supports DDC; DDC2; DDC2B
Automatic Gain Control
System Requirements
Consoles
A VGA, SVGA, or Multisync monitor capable of the highest
resolution that you will be using on any PC in the installation
A PS/2 style keyboard
A PS/2 style mouse
Note: 1. If you connect a DDC type monitor to the Local unit, the
monitor that connects to the Remote unit must be able to
support the highest video resolution that the DDC monitor
can provide.
2. You must use the same brand and model of mouse on both
the local and remote units.
- 3 -
PCs
The following equipment must be installed on each PC that is to be
connected to the system:
With PS/2 Type Connectors:
w A VGA, SVGA or Multisync card.
w A 6-pin mini-DIN mouse port
w A 6-pin mini-DIN keyboard port
With AT Type Connectors:
w A VGA, SVGA or Multisync card.
w A DB-9 (standard serial), mouse port plus mouse adapter (part
# 2A-105).*
w A 5-pin DIN (standard AT), keyboard port plus keyboard adapt-
er (part # 2A-106).*
* Not included - requires separate purchase.
Cables
Although it is possible to use standard extender cables to link
computers with PS/2 type keyboard and mouse ports to the
B013-000 Local, for optimum signal integrity and to simplify the
layout, we strongly recommend that you use the high quality CS
Custom KVM Cable that is provided with this package.
It is not possible to use standard extender cables to link computers
with AT type keyboard and mouse ports to the B013-000 Local.
For those computers, using CS Custom KVM Cables must be used.
Category 5 STP cable is required to connect the local and remote
B013-000 units. Using cable of a lesser standard will result in
degrading the video signal.
- 4 -
Components
The Local Unit (B013-000 Local)
Front View:
1
2
V
9
C
A
CO
N
S
OL
E
O
/
I
E
T
O
M
E
R
3
4
7
5
6
1. Operating Mode Selection Switch
Pressing this button cycles you through the operating mode
choices:
w Local - only the local console can control the system(s);
w Auto - both consoles can control the system(s)).
2. LEDs
The Local Unit has two LEDs to indicate the operating status of
the Local and Remote units (see p. 8, for details).
3. Mouse Port
The local PS/2 mouse plugs into this connector.
4. Keyboard Port
The local PS/2 keyboard plugs into this connector.
5. Monitor Port
The local monitor plugs into this connector.
- 5 -
6. Remote I/O
The Category 5 twisted pair cable that connects to the Remote
Unit plugs into this connector.
7. Power Jack
The cable from the AC Power Adapter plugs into this jack.
The Local Unit (B013-000 Local)
Rear View
CPU
1
2
3
1. Monitor Port
The extension cable that connects to the computer’s VGA port
plugs into this connector.
2. Keyboard Port
The extension cable that connects to the computer’s Keyboard port
plugs into this connector.
3. Mouse Port
The extension cable that connects to the computer’s Mouse port
plugs into this connector.
Note: If you are combining the B013-000 with a KVM switch, the
extension cable connects back to the respective ports on the
Console section of the switch.
- 6 -
The Remote Unit (B013-000 Remote)
Front View
1
9V
C
A
CONSOLE
/O
TE
I
REMO
2
3
6
4
5
1. LEDs
The Remote Unit has two LEDs (Power and On Line) to indicate
the operating status of the Local and Remote units (see p. 8, for
details).
2. Mouse Port
The remote PS/2 mouse plugs into this connector.
3. Keyboard Port
The remote PS/2 keyboard plugs into this connector.
4. Monitor Port
The remote monitor plugs into this connector.
5. Remote I/O
The Category 5 twisted pair cable that connects back to the Local
Unit plugs into this connector.
6. Power Jack
The cable from the AC Power Adapter plugs into this jack.
- 7 -
Installation
Setting up the Console Extender System is simply a matter of
plugging in the cables:
1. Make sure that all the equipment to be connected up is powered Off.
2. Plug the cables from the local console devices (mouse, keyboard,
monitor), into their ports on the Console side of the Local Unit
(B013-000 Local).
3. Plug the appropriate connectors on the KVM extension cable
supplied with this unit into the CPU side of the B013-000 Local.
Each connector is marked with an appropriate icon to indicate
which it is.
Note: The female monitor connector is the one that plugs into the
B013-000 Local.
4. Plug the connectors on the other end of the cable into the
appropriate ports on the PC system (or Console section of the
KVM switch - if you are using one). Each connector is marked
with an appropriate icon to indicate which it is.
5. Plug either end of the Category 5 twisted pair cable into the
B013-000 Local’s Remote I/O port.
6. Plug one of the power adapters (supplied with this package) into
an AC source; plug the adapter’s power cable into the B013-000
Local’s Power Jack
7. Plug the other end of the Category 5 twisted pair cable into the I/O
port of the Remote Unit (B013-000 Remote).
8. Plug the cables from the remote console devices (mouse,
keyboard, monitor), into their ports on the Console side of the
B013-000 Remote.
9. Plug the second power adapter (supplied with this package) into
an AC source; plug the adapter’s power cable into the B013-000
Remote’s Power Jack.
- 8 -
Operation
The Local and Remote Units each have two LEDs to indicate their
operating status, as shown in the tables, below:
B013-000 Local (Local Unit):
Operating Mode
LED
Local
Lights to indicate that the 1. Lights when the local console is
local console is active active (the Remote LED is out)
Auto
Local
(the Remote LED is out). 2. Turns off when the remote console is
active (the Remote LED turns on)
3. Flashes on and off alternately with
the Remote LED when neither
console is active.
Remote
The LED is Off.
1. Lights when the remote console is
active (the Local LED is out)
2. Turns off when the local console is
active (the Local LED turns on)
3. Flashes on and off alternately with
the Local LED when neither console
is active.
B013-000 Remote (Remote Unit):
LED
Power
Indication
1. Lights steadily to indicate that the connection to the Local Unit
is ok.
2. Flashes when there is a problem with the connection to the
Local Unit.
On Line
1. Lights when the remote console is active.
2. Is Off when the local console is active.
3. Is Off when there is a problem with the connection to the
Local Unit.
- 9 -
Appendix
Troubleshooting
Symptom
Action
No Video
Make sure that all cables are securely plugged into their
sockets.
TP Wiring Diagram
PAIR 3
PAIR 2
PAIR 1
PAIR 4
1
W-O
2
O
3
4
5
6
G
7
8
W-G Bl W-Bl
W-Br Br
JACK POSITIONS
T568B
AT&T 258A
TP Pin Assignments
Pin
Assignment
V OUT B
1
2
3
4
5
6
7
8
/V OUT B
V OUT G
V OUT R
/V OUT R
/V OUT G
/DO
DO
- 10 -
Specifications
Function
Connectors Keyboard
Mouse
B013-000 Local
B013-000 Remote
2 x 6 pin mini-DIN female 6 pin mini-DIN female
2 x 6 pin mini-DIN female 6 pin mini-DIN female
Monitor
1 x 15 pin HDB male
1 x 15 pin HDB female
1 x 15 pin HDB female
8P8C Jack
Unit To Unit
LEDs
1 Local
1 Remote
1 Power On
1 On Line
N/A
Function Keys
Cable Length
Local/Auto Select button
150m [500’] (max.)
1024 x 768; DDC; DDC2; DDC2B*
Video Resolution
Power Consumption
Housing
AC 9V 300mA (max.)
Plastic
Weight
300 g
130 x 100 x 35 mm
220 g
Dimensions (L x W x H)
100 x 80 x 35 mm
* DDC, DDC2, and DDC2B support is for the Local monitor only.
- 11 -
PREVENTING RADIO & TV INTERFERENCE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance
with the instruction manual, may cause interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and
receiver; connect the equipment into an outlet on a circuit different from that which the receiver is connected; consult the
dealer or an experienced radio/television technician for help. The user must use shielded cables and connectors with this
product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
1-YEAR LIMITED WARRANTY
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the
date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any
such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA)
number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an
authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of
the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been
damaged by accident, negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, 1TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit
limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the
purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL 1TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost
profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by
third parties, or otherwise.
The policy of TRIPP LITE is one of continuous improvement. Specifications are subject to change without notice.
- 12 -
- 13 -
- 14 -
- 15 -
PAPE-1142-203
- 16 -
|