ELITE 8805
ELITE SERIES
EXPANSION HANDSET
OWNER'S
MANUAL
OWNER'S MANUAL
Installing Your Expansion Handset
Follow these three easy steps to get your new handset ready to use:
1 Install the battery pack.
2 Connect the charger and charge your new handset for 15 - 20 hours.
3 Register your new handset to the main base.
Step 1: Install the Battery Pack
1 Press down on the handset battery case
cover (use the finger indention for a better
grip) and slide the cover downward to
remove.
2 Place the battery pack in the battery
compartment with the connectors on the
battery and on the compartment aligned.
3 Place the battery case cover back on the
handset and slide it upwards until it clicks
into place.
•
Use only the Uniden battery (BT-
0003) supplied with your phone.
Replacement batteries are available.
Please see our website at
Recharge your handset on a regular
basis by returning the handset to
the charger after each phone call.
•
Rechargeable Ni-MH Batteries
Must Be Recycled or Disposed of Properly
(2)
Step 2: Connect the Charger
1 Connect the AC adapter to
the DC IN 9V jack and to a
standard 240V AC wall outlet.
2 Set the charger on a desk or
tabletop, and place the
handset in the charger with
the LCD screen facing
forward.
3 Make sure the charge LED
illuminates. If the LED does not
illuminate, check to see that the AC adapter is plugged in and that
the handset makes good contact with the charger charging contacts.
•
•
Use only the supplied AAD-600S AC adapter. Do not use
any other AC adapter.
Place the charger close to the AC outlet so that you can
unplug the AC adapter easily.
4 Charge the handset for 15 - 20 hours before using.
Step 3: Register the Handset
YOU NEED TO REGISTER THE ELITE8805 SERIES TO THE MAIN BASE
BEFORE USE!
For Backward Compatible Base Models - DSS7800 series [DSS7815,
DSS7815+1, DSS7855 and DSS7855+1]
1
2
Disconnect the AC adapter from the main base.
While pressing down on the following key, reconnect the AC adaptor.
DSS7815/DSS7815+1 models - find handset key
DSS7855/DSS7855+1 models - flash/find hs key
Keep pressing the key until the CHARGE LED starts to blink.
3
On the handset, press and hold the # key until you hear a beep.
(3)
For ELITE8815/ELITE8815+1
1 Press and hold the Registration
button at the underside of the base.
2 Keep pressing the Registration
button until the handset charge
LED on main base starts to blink.
3 On the handset, press and hold the
# key until you hear a beep.
Registration button
For Main Base Models ELITE8855/ELITE8855+1
1 With the main base in standby mode (i.e. not being used), press
menu/select on the base.
2 Use the up/down key to select System Setup.
3 Use the up/down key to select Register Handset.
4 The base LCD screen will display the following prompt:
On handset, press and hold "#" key for 2 sec
5 On the handset, press and hold the # key until you hear a beep.
De-register the handset
1 Press and hold end and # for more than 5 seconds. Select
Deregister Hs.
2 The phone will ask you to confirm the deregistration. Select Yes.
Select Replacing Base at instruction 1 if handset has previously
been registered to another base and you want to register to a new
base.
(4)
Using Your Expansion Handset
Now that your new handset is registered, it can perform all the same
functions as the handsets originally included with your phone. With
your new handset, you can;
•
•
•
Transfer calls between handsets
Use two handsets as 2-way radios in DirectLink mode
Use two handsets or a handset and the base as a baby/room
monitor
•
•
Hold 3 to 4 way conference calls (depends on the model)
Access the integrated answering device or voice mail using the
handset
•
Record Distinctive Ringer Tones
See the owner's manual that came with your main base for complete
instructions on operating your new expanded digital phone. You can
(5)
Using the joystick
The joystick makes it easy
to use your phone. The
four most commonly used
functions are accessible
just by moving the
joystick:
To enter the menu, press the centre of
the joystick inwards.
Highlight the option you want by moving the
joystick up, down, right, or left on the
handset. This will move the cursor; the
option currently highlighted appears in
reversed out text.
Select the highlighted option by pressing in
on the center of the joystick.
To exit the MENU and return to standby, press the end key on the
handset.
To go back a level in the menu, press the
back/hold/int'com .
(6)
Setting Advanced Features
•
When using your handset with the backward-compatible
DSS7800 Series (DSS7815, DSS7815+1, DSS7855 and
DSS7855+1), some advanced features (such as
Reminders) may not be compatible.
•
Please refer to your respective (DSS7815, DSS7815+1,
DSS7855 and DSS7855+1) Owner's Manual.
Record Ringer Tones
1) Connect the audio recording cable to the handset and sound source
(e.g. stereo or CD player). Insert one end of the audio recording
cable into the handset's headset jack and the other end into the
sound source. You can also simply use the handset's microphone by
holding the handset close to the sound source.
2) Select menu option
3) Go to Rec/Edit Rings.
.
4) Select a location from 1-5, and press the OPTIONS soft key.
5) Select Record. To start recording, press the RECORD soft key. The
message counter displays 20 and then begins to count down.
6) When you are finished recording, press the STOP soft key. The
phone will play the recorded ringer. To re-record the ringer, press
the ReRec soft key.
7) Enter the title of this ringer (up to 12 Characters) using the number
keypad, the DELETE soft key, right, or left key.
8) Press the center of the joystick, you will hear a confirmation tone,
and Done! appears.
Set Animation Type
1) Select menu option
.
2) Go to Animation Type and highlight the animation you want.
3) Press the SELECT soft key to activate it.
Set Themes (wallpaper)
1) Select menu option
.
2) Go to Wall Paper and highlight the wallpaper you want. Press the
VIEW soft key to see the wallpaper or the center of the joystick to
activate it.
(7)
Set Color Scheme (Color handsets Only)
1) Select menu option
2) Go to Color Scheme and select the color you want. As you scroll
.
through the options, the phone displays the highlighted color for you.
Creating and Editing Phonebook Entries
Press the joystick to the left, and then press the STORE soft key for the
1st entry. From the 2nd entry, press the OPTIONS soft key. Select New
Entry to store, or Edit Selection to edit the location. Enter as
much information as you want. Press the center of the joystick to enter
each entry and confirm the selection. When you finish, press the DONE
soft key to save this phonebook entry.
Operational Restrictions
Several of your handset's advanced settings such as Room Monitor,
Unique ID and Call Privacy, will operate differently with the DSS7800
Series Phones.
Setting Privacy Mode
Privacy mode prevents interruption from other registered handsets or
the base. This works only when the phone is in use:
While on a call, press the OPTIONS soft key. Use the joystick to select Call
Privacy, Privacy Mode On appears in the display. To exit
Privacy Mode, use the same procedure.
OR
1) Select menu option
2) Go to Handset.
3) Select Call Privacy.
.
4) Use the joystick to select On.
You will hear a confirmation tone.
(8)
Setting Unique ID
You can assign special ringer tones to anyone in your phonebook. When
your phone gets a call, it looks up the Caller ID information in your
phonebook; if you have assigned a distinctive ringer and pictures to
that number, the phone uses them to tell you who's calling.
1) Select
.
2) Go to Handset.
3) Select Unique ID.
4) Use the joystick to select On.
A confirmation tone tells you that distinctive ringing is active.
When viewing a Caller ID entry, the picture that
corresponds to the Phonebook Unique ID setting appears.
If the Unique ID is set to Off, the phone uses the default
picture for viewing Caller ID entries.
Setting Room Monitor On/Off
To prevent the monitoring of a particular handset or the base, simply
turn off the Room Monitor Feature.
To turn off the Room Monitor:
1) Select
.
2) Go to Handset.
3) Select Room Monitor.
4) Use the joystick to select Off.
You will hear a confirmation tone.
(9)
Battery Information
Low battery alert
When the battery pack is very low, the phone is programmed to
eliminate functions in order to save power.
The battery pack needs to be charged when:
30/05 SUN 10:10A
-
-
The empty battery icon appears.
Low Battery appears in the display.
If the phone is in standby mode, none of the
keys will operate. If you are on a call,
complete your conversation as quickly as
possible, and return the handset to the
cradle.
Low Battery
New CID: 10
Cleaning the battery charging contacts
To maintain a good charge, clean the charging contacts on the
handset once a month. Dampen a cloth with plain water. Gently rub
the damp cloth over the charging contacts until all visible dirt is
removed. Dry the contacts thoroughly before returning the handset
to the cradle.
Caution: Do not use paint
thinner, benzene, alcohol, or
other chemical products. Doing
so may discolor the surface of
the telephone and damage the
finish.
(10)
Warranty
UNIDEN ELITE 8805 Handset
Limited One Year Warranty
Note: Please keep your sales docket as it provides evidence of warranty.
Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498
Uniden New Zealand Limited
Warranty only available in original country of purchase
Elements of Warranty: Uniden warrants to the original retail owner for the duration of
this warranty, its ELITE 8805 Handset (hereinafter referred to as the Product) to be free
from defects in materials and craftsmanship with only the limitations or exclusions set
out below.
Warranty Duration: This warranty to the original retail owner only, shall terminate and
be of no further effect ONE (1) Year after the date of original retail sale. This warranty
will be deemed invalid if the product is; (A) Damaged or not maintained as reasonable
and necessary, (B) Modified, altered or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) Improperly installed, (D)
Repaired by someone other than an authorized Uniden Repair Agent for a defect or
malfunction covered by this warranty, (E) Used in conjunction with any equipment or
parts or as part of a system not manufactured by Uniden, (F) Installed, programmed or
serviced by anyone other than an authorized Uniden Repair Agent, or (G) Where the
Serial Number label of the product has been removed or damaged beyond recognition.
Parts Covered: This warranty covers for 1 year, the Handset and Charge Unit only.
Accessories: Batteries, AC adaptor etc are covered for 90 days.
Statement of Remedy: In the event that the product does not conform to this warranty
at any time while this warranty is in effect, the warrantor at its discretion, will repair the
defect or replace the product and return it to you without charge for parts and service.
THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT
OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS
GUARANTEE IS IN ADDITION TO AND DOES NOT AFFECT YOUR RIGHTS UNDER
THE CONSUMER GUARANTEES ACT.
Procedure for obtaining performance or warranty: In the event that the Product
does not conform to this warranty, the Product should be shipped or delivered, freight
prepaid, with evidence of original purchase, (e.g. a copy of the sales docket), to the
warrantor at:
UNIDEN AUSTRALIA PTY LTD
Service Division
UNIDEN NEW ZEALAND LTD
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Fax (02) 9599 3278
150 Harris Road, East Tamaki,
Auckland
Fax (09) 274 4253
© 2005 Uniden Australia Pty Limited/Uniden New Zealand Limited
Printed in China UUZZ01435BZ(0)
|