STEP2 Press the [AUX] button and the [OK/SEL]
button simultaneously for 3 seconds.The
[AUX] Component LED will light for 30
seconds.
STEP1 Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[TV] Component LED will light for 30 seconds.
A. Quick Set-Up Method
C. Auto-Search Method
Introduction
Button Functions
1
4
STEP1 Turn on the Component you want to
Operating Instructions
For 4-Function
Cable Remote Control
STEP1 Turn on the device you want to program-
This remote control is designed to operate all
Motorola and Scientific Atlanta digital set top
boxes (including HD and DVR), plus the
majority of TVs, VCRs, DVDs and AUDIO
equipment on the market as shown below.
program (TV, VCR, DVD or AUX).
to program your TV, turn the TV on.
STEP2 Press the [VOLꢁ] button.
STEP2 Press the [COMPONENT] button (TV,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED will light
for 30 seconds indicating the unit is
ready to be programmed.
STEP2 Point the remote at the TV and press
and hold the TV key for 3 seconds.
While Holding the TV key, the TV LED
will light off and on again. Begin to press
the number keys, one at a time, starting
with 1, then 2, 3…0 until the TV turns off.
STEP3 Press the [COMPONENT] button you want
to setup. Point the remote control toward
the Component and enter the 3-digit code
number assigned to your brand.
STEP3 Press the [TV] button again.
The Component LED will blink twice to
confirm the programming.
To return to original state:
CABLE : Cable Converters TV : Televisions
DVD : DVDs, TV/DVDs, VCRs and TV/VCRs
AUX : Audio Receivers and DVRs, etc.
*Note : If the 3-digit code number you just entered is
the correct number, the Component will turn
Off. If it did not turn Off, continue entering
code numbers listed for that brand until the
Component turns Off.
If you wish to restore the CABLE channel control in
TV mode, repeat the above steps but press [CBL]
UR4U-MDVR-CHD2
STEP3 Point the remote toward the
Component and press the [CHꢀ] or
[CHꢁ] button one step at a time or
keep it pressed. The remote will emit a
series of ON/OFF commands. Release
the [CHꢀ] or [CHꢁ] button as soon as
the Component turns Off.
STEP3 Release the TV key to save the code.
The TV LED will blink twice to confirm
the code is stored.
in STEP3
.
Replacing Batteries
Before you program or operate this remote
control, you must first install two new AA Alkaline
batteries.
2
H. Programming Volume Control
Repeat these steps for your DVD, Aux, etc.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section B). If
any of the functions do not work as they
should, you need to find a new code.
You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:
B. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section B). If any
of the functions do not work as they
should, repeat from STEP 3 using [CHꢀ]
or [CHꢁ] buttons to find the correct code.
STEP1 Remove the battery compartment cover
program (TV, VCR, DVD or AUX) .
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The Component LED light
will blink twice to confirm the code was
stored. Now when you press the AUX
on the back of your remote control.
CBL : TV
T V : TV
STEP2 Press the [COMPONENT] button (TV,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED will light
for 30 seconds indicating the unit is
ready to be programmed.
DVD : TV
AUX : AUX
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
If you wish to operate the CBL volume control in
CBL mode, use the following steps.
STEP5 Save the code. (Same as for 3-Digit Code
th
button, all the buttons will work with that 4
STEP1 Press the [CBL] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] Component LED will light for 30
seconds.
STEP3 Replace the battery compartment cover.
Programming Method - Section B).
Component.
Now, repeat the Auto-Search Method for those
Components you could not program earlier with the
Pre-Programmed Method.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
F. Programming the System On/Off Button
This allows you to program the System On/Off button
so it can send up to four power On/Off commands
with one button press.
STEP2 Press the [VOLꢀ] button.
STEP3 Press the [CBL] button.
The Component LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the TV volume control in CBL
mode, repeat the above steps but press [TV]
D. Finding a Component Button’s
Setup Code Number
If you used the Auto-Search Method to program a
Component, you may not know what the correct code
number is. Here is a way for you to identify the code
number, so you can record it for future reference.
*Note : If the 3-digit code number you just
entered is correct, the Component will
turn Off. If it did not turn Off, continue
entering code numbers listed for that
brand until the Component turns Off.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED will
light for 30 seconds.
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn
the Component back On. Now it’s time
to test the VOLUME and MUTE buttons
for the TV (or PLAY and STOP buttons
for VCR and DVD) to make sure they all
work. If any of the functions do not
work as they should, repeat from STEP
3 using the next 3-digit code number
listed for that brand.
in STEP3
.
STEP1 Press the [COMPONENT] button (TV, DVD or
AUX) you want to verify and the [OK/SEL]
button simultaneously for 3 seconds. The
Component LED will light for 30 seconds.
STEP3 Press the first [COMPONENT] button you
want to store in the [SYSTEM ON/OFF]
button and then the [POWER] button.
Repeat this for other Components until you
have stored all the desired power
commands into the [SYSTEM ON/OFF]
button.
I. Programming a Favorite Channel
See on-screen Guide Menu.
Programming the Remote Control
There are three ways you can program your remote control:
5
J. Low Battery Warning
STEP2 Press the [INFO] button and count the
number of times the Component LED light
blinks. This number indicates the first digit
of the code, followed by the second and
third, each separated by a one second
pause when the LED will turn off.
When the batteries are low and need to be
replaced with fresh batteries, the Component LED
lights will blink 2 times in sequence whenever a
[POWER] button is pressed to turn on equipment.
Operations
3
Quick Set-Up Method
*
STEP4 Press the [CHꢀ] button to save the power
commands you stored. The [CBL] button
will blink twice to confirm the commands
have been saved.
The Pre-Programmed 3-Digit Code Method
*
DEFAULT STATUS:
Component Default: CABLE
Channel Default: CABLE channel +/- and
numbers operate through the CABLE box.
You have the option of controlling channel +/-
and numbers through the TV, VCR or DVD.
Refer to section G for programming steps.
The Auto-Search Method
*
STEP5 Once you have found the correct 3-
digit code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink
twice to confirm that the code was
successfully stored.
K. Memory Lock System
The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using
one-digit codes for up to 10 major brands for each component.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code
numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and
easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-
Search Method scans through all the codes in the remote control, one at a time.
*Note : 10 blinks represents the number zero.
This remote control is designed to retain
programmed memory for 10 years even after
batteries are removed from the remote control.
G. Programming Channel Control
Example : One blink, (pause), eight blinks, (pause) and
three blinks, indicates code number 183.
You can program the channel controls (Channel Up,
Channel Down, Last and Numbers) from one
Component to operate in another Component mode.
Default channel control settings on the remote control
are as follows:
th
E. AUX Function: Programming a 4
Component
L. Record Your Component Set-up Codes
Now, program the rest of your Components by
repeating STEPS 1-5.
TV
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
IMPORTANT SETUP NOTES:
Volume Default: CABLE volume +/- and mute
operate through the TV. You have the option
of controlling volume through the Cable box,
VCR or DVD. Refer to section H for
programming steps.
You can take advantage of the AUX function to
*Note : If the Pre-Programmed Method did
not work, or if the Code Tables do not
list your Component brand, use the
Auto-Search Method as explained in
Section C.
DVD
AUX
th
This pertains to all programming steps. When you are in setup mode in each component, a component
LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off
and exit setup mode and you will need to start over.
program a 4 Component such as a second TV, VCR,
CBL : CBL
T V : CBL
DVD or Audio Component.
Universal Remote Control, Inc.
DVD : DVD
AUX : AUX
th
STEP1 Turn on the 4 Component you want to
If you wish to operate the TV channel control in TV
mode, use the following steps.
For additional information about your remote control,
When programming a combo unit, program as a VCR or DVD first.
OCE-0053A REV 20(08/17/11)
program (TV, VCR, DVD or Audio).
|